REPAIR/MAINT/REPLACEMENT OF LT DISTRIBUTION, CONTROL SWITCH GEAR, GARDEN LIGHTS, STREET LIGHTS AND INTERNAL ELECTRIFICATION WORK FOR AMC RECORD PAO TOPKHANA AND 11 GRRC RECORD PAO AT PCDA OFFICE COMPLEX AND RTC BUILDING UNDER GE E/M LUCKNOW

Amount

Taking down chowkhats or frame (wooden/aluminium) n. exc. 1.5 Sqm each with shutters (with out taking off shutters from the frame) and taken as credit complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames (wooden/aluminium) with shutters without taking off shutter from the frames exc. 1.5 but n. exc 4 sqm each complete all as specified and directed by Engineer-in-Charge

Taking down shutter only n. exc 1.0 sqm each complete all as specified and directed by Engineer-in-Charge

Taking down shutter only exc 1.0 sqm but n.exc 2.00 sqm each complete all as specified and directed by Engineer-in-Charge

S&F 2nd class Hard wood in plain, solid, straight chowkats and frames wrought framed, rebated on the solid, rounded or chamfered put together with glue pinned joints complete all as specified and directed by Engineer-in-Charge

S&F Bands, straps, clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed by Engineer-in-Charge

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate for fixing of hold fast and making good complete all as specified and directed by Engineer-in-Charge

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications& drawing complete all as specified and directed by Engineer-in-Charge

Factory made solid panel PVC Door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail,lock rail and bottom rail on either side as gap insert for top rails, bottom rail,panelling of plain colour PVC sheet to be fitting in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supply & fixing in the frame at site as per specification and drawing on Page No 156 of SSR Part-II Rates,complete all as specified and directed by Engineer-in-Charge

Factory made flush shutters 35 mm thick, solid core construction , with block board core and plywood face panels, commercial type on both sides , complete all as specified and directed by the Engineer in Charge.

S&F 100mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed by Engineer-in-Charge

S&F 75mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed by Engineer-in-Charge

S&F 150mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed by Engineer-in-Charge

S&F 150mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge

S&F 100mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge

S&F Aluminium alloy, anodized, sliding door bolt (ISI Marked) of 300mm with hasp & staple (Bolt type) and fixing clips of sheets, coat or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engineer-in-Charge

M&L Preparation of new wooden surface exceeding 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge

S&F in repairs galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in wooden/steel/aluminium window/door with clips and necessary beading complete all as specified and directed by Engineer-in-Charge

Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames , glazed with putty or fixed with beads in repairss complete all as specified and directed by Engineer-in-Charge

S&F glass pan ordinary quality 3mm thick and glazing with oil putty/ neoprene beadings in square n. exc 0.5 m each pane complete all as specified and directed by Engineer-in-Charge

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty n.exc 0.5 Sqm each pane complete all as specified and directed by Engineer-in-Charge

S&f for 4.8 mm thick sheet glass ordinary qulity and glazing with neosprene beading exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. at any height complete all as specified and directed by Engineer-in-Charge

All as per item no 23 above but on ceiling surfaces

M&L rendering 15mm thick on brick wall or concrete surface in cement mortar 1:6 finished fair and even without using extra cement complete all as specified and directed by Engineer-in-Charge

M&L rendering 10mm thick on brick wall or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge

M&L rendering 10mm thick on ceiling in cement mortar 1:3 finished fair and even without using extra cement complete all as specified and directed by Engineer-in-Charge

M&L applying three coat of white wash on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified and directed by Engineer-in-Charge

M&L for applying two coats of Oil bound distemper over a coat of cement based white wall care putty average thickness 3mm thick including preparation of newly plastered surfaces complete all as specified and directed by Engineer-in-Charge

M&L applying two coat of cement base paint on newly plastered or undecorated wall surfaces including preperation of surfaces, complete all as specified and directed by Engineer-in-Charge

M&L applying three coat of white wash on newly plastered or unplastered ceiling surfaces including preperation of surfaces, complete all as specified and directed by Engineer-in-Charge

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge

All as per item No 32 above but on ceiling.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade complete all as specified and directed by Engineer-in-Charge

Preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

M&L applying two coat of cement base paint on old decorated wall surfaces including preperation of surfaces, complete all as specified and directed by Engineer-in-Charge

Preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Complete removal of existing treatment of walls and applying two coats of distemper oil emulsion over and including a coat of primer over and including a thin layer of wall care putty on old plastered surfaces including prepration complete all as specified and directed by Engineer-in-Charge

Taking up or down steel water tubing and connections of 40 mm bore complete all as specified and directed by Engineer-in-Charge

Taking up or down steel water tubing and connections of 20 mm bore complete all as specified and directed by Engineer-in-Charge

M & L Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors 40 mm bore complete all as specified and directed by Engineer-in-Charge

M & L Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors 20 mm bore complete all as specified and directed by Engineer-in-Charge

S&F in repairs 15 mm dia bib tap cast copper alloy(fency type), chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge

S&F in repairs 15 mm dia long body bib tap cast copper alloy(fency type), chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge

S&F in repairss stop valve, cast copper alloy, fancy type,chromium plated screwed down both ends for high pressure (concealed type), as per ISI suitable for 15mm dia iron pipe complete all as specified and directed by Engineer-in-Charge

S&F in repairs Brass chromium plated shower rose 125mm size with swivel joints, suitable for 15mm dia GI pipe complete all as specified and directed by Engineer-in-Charge

S&F in repairs PVC low level flushing cistern (white) 10 Ltrs capacity with internal fitting, push button operated type with and including bracket, PVC flush pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous China wash down water closet pan ( padestal pattern Water Closet (white) , ( excluding fixing bolts, flushing cistern and flush pipe) , including connection to drain ( or outgoing pipe) and to flushing pipe , etc., complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairss Plastic water closet seat, white, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-Charge

S&F in repairss 32 mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified and directed by Engineer-in-Charge

M&L in repairss 32 mm waste fittings , brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge

S & F Neosprene rubber beading including taking down old rubber beading as in aluminium window and door shutter complete all as specified and directed by Engineer-in-Charge

S & F washer for flushing cistern including taking down old washer complete all as specified and directed by Engineer-in-Charge

S & F PVC Syphon to PVC flushing cistern including taking down old syphon, complete all as specified and directed by Engineer-in-Charge

S&F in repairs PVC connection 15mm size with PTMT nuts, of 450mm length complete all as specified and directed by Engineer-in-Charge

S&F in repairss CP mild steel gratings suitable for 75/100 mm dia NT/ FT complete all as specified and directed by Engineer-in-Charge

S&F in repairss Chromium plated Brass Tubular towel rod, of 24" (60 cm long) complete all as specified and directed by Engineer-in-Charge

S&F 20mm dia ball Brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipes or brass ferrule and fixed as in PVC OHT tanks complete all as specified and directed by Engineer-in-Charge

S&F 40mm dia ball Brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipes or brass ferrule and fixed as in PVC OHT tanks complete all as specified and directed by Engineer-in-Charge

S&F in repairs 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to 20mm dia GI tube complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (un-reinforced) in ground floor and pavings n. exc 15 cm thick (above or below ground level) complete all as specified and directed by Engineer-in-Charge

M & L for cement concrete type D 2, 1:4:8 (40mm graded aggregate) 75 mm thick as in sub base of floor complete all as specified and directed by Engineer-in-Charge

M & L for cement concrete type B 2, 1:2:4 (40mm graded aggregate) 75 mm thick as in sub base of floor complete all as specified and directed by Engineer-in-Charge

S&F in repairs CP Angle stop cock ( one way) long thread with wall flange , fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed by Engineer-in-Charge

S&F in repairs cp angle cock (two way) complete all as specified and directed by Engineer-in-Charge

S&F health faucet CP with 15 mm dia fixed in repairs complete all as specified and directed by Engineer-in-Charge

S&F in repairss Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without lettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed by Engineer-in-Charge

S & F for Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge

S & F in repairs for 15/20mm dia brass standard size spare part and internal fittings for bib tap, angle/stop cock, pillar tap, basin mixer etc. complete all as specified and directed by Engineer-in-Charge

M & L for Aluminium Anodised door frame with shutter, including necessary joining cleats, glazing clips rubber neoprene packing , Handle 2 Nos,1 Nos 200mm aluminium anodised tower bolt, 1 No double action floor spring in each shutter, anodised aluminium snap beading screw necessary locking arrangement with mortice lock, incluing 4.8mm thick ordinary sheet glass or galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm, complete all as specified and directed by Engineer -in-charge.

M & L for Anodised aluminium window and ventilator frame with shutters, fixed type without sash bar, including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. , complete all as specified and directed by Engineer -in-charge.

M & L for Anodised aluminium window and ventilator frame with shutters, side hung type without sash bars, including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) including 3.0 mm thick ordinary sheet glass or galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed by Engineer-in-Charge

M & L for Anodised aluminium window and ventilator shutters, side hung type without sash bars, including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) including 3.0 mm thick ordinary sheet glass or galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed by Engineer-in-Charge

Repairing of existing aluminium door single leaf including oiling and greasing of floor springs,replecing of rubber beading if required,replacement of hinges,handle,towerbolt of any size any type present at site on required basis,also including replacement of any membre of aluminium section i.e frame & shutters membre and 5-12 mm glass and making the door and shutter serviceable , complete all as specified and directed by Engineer -in-charge.Note :Floor door springs where renewed shall be measured and paid separately under appropriate item.

Repairing of existing aluminium door double leaf including oiling and greasing of floor springs,replecing of rubber beading if required,replacement of hinges,handle,towerbolt of any size any type present at site on required basis,also including replacement of any membre of aluminium section i.e frame & shutters membre and 5-12 mm glass and making the door and shutter serviceable complete all as specified and directed by Engineer-in- Charge. (Floor door springs where renewed shall be measured and paid separately under appropriate

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repairs, complete all as specified and directed by Engineer -in-charge.

Aluminium body ( extruded section ) body Door closer hydraulically regulated, designation No. 3 , universal type , suitable for door shutters 851 to 1000 mm in width and of weight between 61 to 80kg and fixed as in repairs , complete all as specified and directed by Engineer -in-charge.

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets , complete all as specified and directed by Engineer-in- Charge.

Suspended ceiling, comprising 12.5 mm thick reinforced gypsum plaster boards Conforming to IS-2095 , GI perimeter channels, intermdiate channels, etc. including finishing the exposed surfaces with Oil bound distemper two coats , complete all as specified and directed by Engineer-in- Charge.

S & F for 2mm thick Fibre glass reinforced translucent plain sheeting in dome shape with 100 mm lap fixed with coach screw and washer etc. complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) rubbish off the premises complete all as specified and directed by Engineer-in-Charge

M&L for glazed ceramic tiles in vertical surfaces 350 x 250 x 7 mm / 450 x 350 x 7 mm [thick] set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10mm thick screed in CM 1:3 complete all as specified and directed by Engineer-in-Charge (Note : Screed bed will not be measured and paid separately)

Taking down carefully aluminium/Copper conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately)and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing complete all as specified and directed by Engineer-in-Charge

M&L point wiring for one light/fan point controlled by one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly and make wall surfce as existing same colour complete all as specified and directed by Engineer-in-Charge .

M&L point wiring for one socket outlet point 5 amps on independent board controlled by one, one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly complete all as specified and directed by Engineer-in-Charge

Ditto all as above item no 86 hereinbefore but one socket outlet point on same baord with other switches with 1.5 sq mm single core multistranded PVC insulated FRLS cable including 1.5 sq mm single core multi stranded copper cable used as continuous earth wire

M&L point wiring for 15 amps socket point controlled by one, one way switch using 2.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated FRLS unsheathed cables in and including PVC concealed conduit and conduit fittings including pressed steel terminal switch boxes and 3 mm thick plate for fixing of switches/sockets and fitted with Chromium plated brass screws & washers and1.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated unsheathed earth wire and connected to earth dolly complete all as specified and directed by Engineer-in-Charge

S&F Polycarbonate switch piano flush type, SP,5/6 Amps, one way complete all as specified and directed by Engineer-in-Charge

S&F Polycarbonate switch piano flush type, SP, 16/20 Amps, one way complete all as specified and directed by Engineer-in-Charge

S&F Polycarbonate socket out let 2 in 1 socket 5 pin, (6 Amps) flush type controlled by one switch, complete all as specified and directed by Engineer-in-Charge

S&F Polycarbonate socket out let 6 pin, 20 Amps complete all as specified and directed by Engineer-in-Charge

M&L ceiling rose, Pilot 3 Plate ceiling rose 6A, complete all as specified and directed by Engineer-in-Charge

S&F ( in repairs) Moduler switch 10 Amp, SP, one way , 220 Volts AC, square white mechanisms & ISI marking complete all as specified and directed by Engineer-in-Charge

S&F ( in repairs) Moduler switch Modular switch 1 way 16A, 1 modules square white mechanisms ISI marking complete all as specified and directed by Engineer-in-Charge

S&F ( in repairs) Moduler socket shuttered 6 Amps, 3 Pin Universal India -2 module,complete ISI marking complete all as specified and directed by Engineer-in-Charge

S&F ( in repairs) Moduler socket shuttered 6/16 Amps, 3 Pin Universal India -2 module, ISI marking complete all as specified and directed by Engineer-in-Charge

S&F ( in repairs) Ceiling fan regulator electronic type deluxe 240 , 5 step , Volts ISI Marked specified make complete all as specified and directed by Engineer-in-Charge

S&F ( in repairs)White cover plate with frame, 1 module, complete all as specified and directed by Engineer-in-Charge

S&F ( in repairs) White cover plate with frame, 2 module complete all as specified and directed by Engineer-in-Charge

S&F ( in repairs) Metal flush box 1/ 2 module, complete all as specified and directed by Engineer-in-Charge.

S&F ( in repairs) Switch socket combination 2 in 1 , 3 pin , 5 & 15 amp flush type universal, complete all as specified and directed by Engineer-in-Charge.

S&F ( in repairs) socket outlet multipurpose 3 pin , 20/10 Amps ISI marking , controlled by one switch complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet multipurpose 3 pin , 6 Amps and one pin,controlled by one switch ISI marking complete all as specified and directed by Engineer-in-Charge.

S&F ( in repairs) Switch, 06 way white coloure complete all as specified and directed by Engineer-in-Charge

S&F ( in repairs) Switch, 16 way white coloure complete all as specified and directed by Engineer-in-Charge

S&F (in repairs) epoxy powder coated distribution box Double door type SPN 4 way,with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door complete all as specified and directed by Engineer-in-Charge

S&F (in repairs) epoxy powder coated distribution box Double door type SPN 8 way,with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door complete all as specified and directed by Engineer-in-Charge

S&F (in repairs) epoxy powder coated distribution box Double door type SPN 12 way, with 200 amps rated bus bar,240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal door complete all as specified and directed by Engineer-in-Charge

S&F (in repairs) MCBs MCB SP, 6 to 32 Amps B /C seires , 240 Volts to be housed in DBs Proper and suitable size cable lugs to be fixed with MCBs are including in unit rate of each complete all as specified and directed by Engineer-in-Charge

S&F (in repairs) MCBs MCB SPN/Isolator single pole and neutral link, 40 Amps , 240 Volts to be housed in DBs Proper and suitable size cable lugs to be fixed with MCBs are including in unit rate of each complete all as specified and directed by Engineer-in-Charge

S & F (in repairs) Single pole enclosure box suitable for MCB SP of capicity 6 to 32 Amps B/C type complete all as specified and directed by Engineer-in-Charge .

S & F (in repairs) DP/TP/FP enclosure box suitable for MCB SPN/MCCB of Capicity 32 to 63 amps ,SPN/TP/TPN complete all as specified and directed by Engineer-in-Charge.

M&L for concealed sub main wiring comprising two single core, 4 Sq mm nominal cross sectional area multi on same copper conductor cable, PVC insulated FRLS Grade unsheathed 1100 Volts grade drawing in and over PVC conduits and conduit fittings complete (concealed type) including S&F 4 Sq mm nominal cross sectional area n green coloure on same copper conductor cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed by Engineer-in-Charge (Cutting chases and making good of disturbed surfaces shall deem to be including in the unit rate quoted by tendered).(Note :- Extra length of cables/wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly) Make of PVC insulated unsheathed FRLS copper cable Finolex/Havells/POLYCAB .

M&L for concealed sub main wiring comprising two single core, 10 Sq mm nominal cross sectional area multi on same copper conductor cable, PVC insulated FRLS grade unsheathed 1100 Volts grade drawing in and over PVC conduits and conduit fittings complete (concealed type) including S&F 10 Sq mm nominal cross sectional area on same copper conductor cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed by Engineer-in-Charge (Cutting chases and making good of disturbed surfaces shall deem to be including in the unit rate quoted by tenderer). (Note :- Extra length of cables/wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly) Make of PVC insulated unsheathed FRLS copper cable Finolex/Havells/POLYCAB .

M&L ( in repairs) earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in to ground (earth pit) not less than 2.25 meters deep below GL with top edge of earth plate not less than 1.50 m below ground level, connected to GI lead wire of 4 mm dia. (7.50 m long) by means of nuts, bolts and washers, check nuts of GI and protected by the GI pipe light grade 1.5 mm nominal bore (7.50 m Long) for earth plead wire, watering pipe light grade of 20 mm nominal bore, 0.63 mm thick CI funnel, wire mesh etc complete including necessary earth work and excavation in any type of soil, PCC 1:2:4 type B1 earth pit and Precast RCC cover 50 mm thick dully reinforced with 6 mm dia, MS round bars @ 100 mm C/C both ways, earth testing point, making good to floor complete all as specified and directed by Engineer-in-Charge

M&L ( in repairs) Distribution Board TPN with and including of DPX MCCB 35 KA 250 Amps MCCB FP, as incomer and SP/TPN MCBs as outgoing protection class IP 54, 8 way (DPX 250+24) with metal double door as in repairslacement,complete all as specified and as directed by Engineer-in- Charge. Note :- FP MCCBs 35 KA 250 Amps 1 No and 24 Nos MCB SP 32 Amps 230 Volts and Blanking plate shall be measured and paid under this this item .

M&L ( in repairs) Distribution Board TPN with and including of DPX MCCB 35 KA 160 Amps MCCB FP, as incomer and SP/TPN MCBs as outgoing , 4 way with metal double door as in repairslacement,complete all as specified and as directed by Engineer-in- Charge. Note :- FP MCCBs 35 KA 160 Amps 1 No and 24 Nos MCB SP 32 Amps 230 Volts and Blanking plate shall be measured and paid under this this item

M&L ( in repairs) Distribution Board TPN with and including of 100 amp FP Isolator, as incomer and SP/TPN MCBs as outgoing , 4 way with metal double doorwith metal double door as in repairslacement,complete all as specified and as directed by Engineer-in- Charge. Note :- FP Isolator 100 Amps 1 No and 12 Nos MCB SP 32 Amps 230 Volts and Blanking plate shall be measured and paid under this this item

Supply and fixing in repairs flexible copper cable three core 0.75 sqm white coloure flat type suitable for connection for electric fititing and fixture complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs flexible copper cable three core 1.5 sqm suitable for connection for electric fititing and fixture complete all as specified and directed by Engineer-in-Charge

Supply and fixing flexible copper cable three core 2.5 sqm suitable for connectionfor electric fititing and fixture complete all as specified and directed by Engineer-in-Charge

Supply and fixing (in repairss) 15 amp plug top complete all as specified and directed by Engineer-in-Charge.

Supply and fixing (in repairss) 5 amp plug top complete all as specified and directed by Engineer-in-Charge.

Supply and fixing(in repairs) suitable for 5 amp gang box with switch and socket complete all as specified and directed by Engineer-in-Charge

Supply and fixing(in repairs) suitable for 15 amp gang box with switch and socket complete all as specified and directed by Engineer-in-Charge

Supply and fixing ( in repairs) LED CFL 4 pin 36 watts 4 Pin , suitable for CFL light fittings witn electric connection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing(in repairs) of Recess LED llight fittings of 05 watt LED made of CRCA powder quoted finish with Fully Covered by PMMA Acrylic Lumio Diffuser, LED Used shall be SMD type and fixture including cutting and making false ceiling of any pattern/mtrl proper fixing of light in falce ceiling , electrical connection up to 15 feet height of various ward and dept complete all as specified and directed by Engineer-in-Charge.

Supply and fixing(in repairs) of Recess LED llight fittings of size 2X2 36 watt LED made of CRCA powder quoted finish with Fully Covered by PMMA Acrylic Lumio Diffuser, LED Used shall be SMD type and fixture including cutting and making false ceiling of any pattern/mtrl proper fixing of light in falce ceiling , electrical connection up to 15 feet height of various ward and dept complete all as specified and directed by Engineer-in-Charge.

S&F ( in repairs) Decorative ultra slim round profile LED lighting fixture with extruded polycarbonate, environmental friendly,energy efficient ready to use pack LED TUBE light fittings with battern of capicity 18 watt (2 feet) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing(in repairs) of Recess LED llight fittings of 4X1 of 30 watt LED made of CRCA powder quoted finish with Fully Covered by PMMA Acrylic Lumio Diffuser, LED Used shall be SMD type and fixture including cutting and making false ceiling of any pattern/mtrl proper fixing of light in falce ceiling , electrical connection up to 15 feet height of various ward and dept complete all as specified and directed by Engineer-in-Charge.

S & F ( in repairs) Lamp holderbattern/anguler type , PVC/polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and directed by Engineer-in-Charge

Taking down old unserviceable FTL T/L rod any watt and Supply and fixing LED tube light Rod 18/20 watt 4 feet retro complete all as specified and directed by Engineer-in-Charge.

Taking down old unserviceable FTL battern and S& F Ultra bright, glass shell, glare free, wide angle, single side connection retofit LED tube with G13 lamp holders. New batten suitable for LED tube rod 18/20 watt pre wired including connection complete all as specified and directed by Engineer-in-Charge.

Supplying and laying or fixing in repairslacement, jointing and testing LT under ground electric power cable crossed linked polyethylene ( XLPE) insulated, galvanised steel strip or wire armoured, ISI-7098 Marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of size 10 sqmm cross sectional area, 2 core ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc. with and including MS Clamps, nuts , bolts, washers complete all as specified and directed by Engineer-in-Charge Note :- Excavation, earth work, sand cushioning, protection bricks/ tiles/ block and pipe shall be measured and paid separately under appropriate items.

All as per item No 135 above but of size 10 Sqmm 4 core

All as per item No 135 above but of size 16 Sqmm 4 core

All as per item No 135 above but of size 25 Sqmm 3.5 core

All as per item No 135 above but of size 50 Sqmm 3.5 core

S & F GI Pipes galvanized, “light grade ”, laid in trench complete including fittings 80 mm dia.protection for LT Cable complete all as specified and directed by Engineer-in-Charge

Supplying, transporting, erecting and fixing Steel tubular swaged poles type 410 SP-31 ( 9.0 metres long) complete with cast iron base plate, finial, taper plug, bolts, nuts and screws as specified, including necessary excavation and earth work , PCC 1:4:8 type D2 in foundations below pole, PCC 1:3:6 type C2 around poles and PCC 1:3:6 type C1 as in plinth block , disposal of surplus soil to a distance not exceeding 50 m and depositing where directed, painting steel tubular poles exposed surafces with Aluminium paint two coats over one coat of red oxide primer and providing 300 mm wide bands (3 bands/ straps with synthetic enamel paint and 2 bands with Black bituminous paint ) from plinth block and numbering of poles , painting embedded portion of poles with one coat of bituminous paint complete all as specified and directed by Engineer-in-Charge (OLD MTRL SHOULD BE DEPOSITED IN RTC STORE yARD)

S & F street light panel single phase up to 6 kw load with Astronomical digital timer and MCCB of capacity 32 / TP and SPN 40 Amps fixed on wall/pole with clamps,nut bolts complete all as specified and directed by Engineer-in-Charge.

Supply, fixing, connecting and testing energy saving LED street light fittings of 90 Watt with thermal management, potted driver, pressure die cast housing LM 6 alloy/anti dust exposed lens, in built tilt angle arrangement and environment friendly long life with IP66 protection on existing street light poles and bracket complete all as specified and directed by Engineer-in-Charge.

Supply, fixing, connecting and testing energy efficient LED flood light fittings of 215 Watt pressure die cast aluminium housing and IP66 protection including XLPE armoured cable 2 core 4 Sqmm up to 5 mtr from fitting to panel box with emitter complete all as specified and directed by Engineer-in-Charge.

Supply, fixing, connecting and testing energy efficient LED flood light fittings of 145/150 Watt pressure die cast aluminium housing and IP66 protection including XLPE armoured cable 2 core 4 Sqmm up to 5 mtr from fitting to panel box with emitter complete all as specified and directed by Engineer-in-Charge.

Supply, fixing, connecting and testing energy efficient LED bollard light of 18 Watt including foundation work with PCC as required complete all as specified and directed by Engineer-in-Charge.

Supply, fixing, connecting and testing energy efficient LED POST TOP LANTERN WITH SYMMETRIC LIGHT DISTRIBITION AND LIMITED UPWARD LIGHT COMPONENT light of 18 Watt in repairs replacement complete all as specified and directed by Engineer-in-Charge.

S & F Voltage stabilizer for automatic operation single phase n ntelligent Time Delay System, Compatible with Regular & Inverter ACs, Wall Mounting Cabinet Design, Energy efficient design, smart Digital Display, Built In Thermal Overload Protection Low & High Voltage Cut-off Protection, Latest IC Technology of capacity 05kVA . make -V Gaurd Cat part MOP suitable for 2.0 TR inverter AC or eqvlnt (OLD MTRL SHOULD BE DEPOSITED IN RTC STORE yARD)

Supply & fixing exhaust fan 380 mm sweep AC 230 volts single phase with louvers including making connection with three core PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified and directed by Engineer-in-Charge Make: Bajaj/CG

Supply & fixing exhaust fan 450 mm sweep AC 230 volts single phase with louvers including making connection with three core PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified and directed by Engineer-in-Charge. Make: Bajaj/CG (OLD MTRL SHOULD BE DEPOSITED IN RTC STORE YARD)

Supply & fixing exhaust fan fresh air 250 mm sweep AC 230 volts single phase with louvers including making connection with three core PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified and directed by Engineer-in-Charge (OLD MTRL SHOULD BE DEPOSITED IN RTC STORE yARD)

Supply, installation testing and commissioning of storage type water heater 25 ltrs capacity vertical mounting type complete made out of CRCA outer body, copper storage tank, heating element,thermostat,thermal cut out, glass wool etc. complete including making necessary electrical connections with suitable size copper multistranded cable complete all as specified and directed by Engineer-in-Charge (OLD MTRL SHOULD BE DEPOSITED IN RTC STORE yARD)

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil complete all as specified and directed by Engineer-in-Charge

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed by Engineer-in-Charge

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete all as specified and directed by Engineer-in-Charge Note :- Punned thickness shall only be considered for payment

M&L laying well burnt old size bricks, sub class "B" bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection complete all as specified and directed by Engineer-in-Charge

M&L for outdoor type cubical panel board made out of 3.15 mm thick CRCA sheet and inner shell made out of 1.6 mm thick CRCA sheet and MS angle section 50x50x6 mm, factory fabricated front openable double door system suitable for 3 phase 4 wire 415 volts, powder coat RAL 7035 painting having thickness 90 microns comprising of the following :- a) The TPN busbar duly plated copper busbar fitted in cascaded moulding. b) Incoming MCCB 400 Amps 36 kA, 415 volts, FP - 01 Nos c) Outgoing MCCB 250 Amps 25 kA, 415 volts, FP - 01 Nos d) Outgoing MCCB 200 Amps 25 kA, 415 volts, FP - 02 Nos e) Outgoing MCCB 160 Amps 25 kA, 415 volts, FP - 01 Nos Voltage/Ampere/Frequency meter multi functional meter - 01 No f) LED indicator lamp RYB - 01 Set of three

M&L ( in repairs) earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in to ground (earth pit) not less than 2.25 meters deep below GL with top edge of earth plate not less than 1.50 m below ground level, connected to GI lead wire of 4 mm dia. (7.50 m long) by means of nuts, bolts and washers, check nuts of GI and protected by the GI pipe light grade 1.5 mm nominal bore (7.50 m Long) for earth plead wire, watering pipe light grade of 20 mm nominal bore, 0.63 mm thick CI funnel, wire mesh etc complete including necessary earth work and excavation in any type of soil, PCC 1:2:4 type B1 earth pit and Precast RCC cover 50 mm thick dully reinforced with 6 mm dia, MS round bars @ 100 mm C/C both ways, earth testing point, making good to floor complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs flexible copper cable three core 0.75 sqm white coloure flat type suitable for connection for electric fititing and fixture complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs flexible copper cable three core 1.5 sqm suitable for connection for electric fititing and fixture complete all as specified and directed by Engineer-in-Charge

Supply and fixing flexible copper cable three core 2.5 sqm suitable for connectionfor electric fititing and fixture complete all as specified and directed by Engineer-in-Charge

Supply and fixing(in repairs) suitable for 5 amp gang box with switch and socket complete all as specified and directed by Engineer-in-Charge

Supply and fixing(in repairs) suitable for 15 amp gang box with switch and socket complete all as specified and directed by Engineer-in-Charge

S & F ( in repairs) Lamp holderbattern/anguler type with led bulb , PVC/polycarbonate type with cord grip cap suitable for garden light fittings complete all as specified and directed by Engineer-in-Charge

Supply and fixing (in repairs) LED tube light Rod 18/20 watt 4 feet retro complete all as specified and directed by Engineer-in-Charge.

S& F (in repairss) Ultra bright, glass shell, glare free, wide angle, single side connection retofit LED tube with G13 lamp holders.New batten suitable for LED tube rod 18/20 watt pre wired including connection complete all as specified and directed by Engineer-in-Charge

Disconnecting all existing electrical connection from panel ,taking out unserviceable MCCB and cable from LT panel Board and Supply, fixing, connecting and testing of MCCB 63 Amp 3 pole 16 KA fixed type 415 volts 50 Hz with spreader with suitable size of cable lugs/thimble complete incl all electrical connection with making good the damaged surface complete all as specified and directed by Engineer-in-Charge

Disconnecting all existing electrical connection from panel ,taking out unserviceable MCCB and cable from LT panel Board and Supply, fixing, connecting and testing of MCCB 100Amp 3 pole 16 KA fixed type 415 volts 50 Hz with spreader and suitable size of cable lugs/thimble complete incl all electrical connection with making good the damaged surface complete all as specified and directed by Engineer-in-Charge

Disconnecting all existing electrical connection from panel ,taking out unserviceable MCCB and cable from the LT panel Board and Supply, fixing, connecting and testing of MCCB 160 Amp 4 pole 25 KA fixed type 415 volts 50 Hz with spreader and suitable size of cable lugs/thimble complete incl all electrical connection with making good the damaged surface complete all as specified and directed by Engineer-in-Charge

Disconnecting all existing electrical connection from panel ,taking out unserviceable MCCB and cable from the LT panel Board and Supply, fixing, connecting and testing of MCCB 200 Amp 4 pole 25 KA fixed type 415 volts 50 Hz with spreader and suitable size of cable lugs/thimble complete incl all electrical connection with making good the damaged surface complete all as specified and directed by Engineer-in-Charge

Supplying and laying in repairss of 1100 Volt grade heavy duty PVC cable with PVC insulated alluminium conductor served with inner sheathing pf PVC tape armoured XLPE cable with galvanized steel wire or tape and over all PVC sheathed 10 sq. mm 2 core nominal cross sectional area complete all as specified and directed by Engineer-in-Charge

Disconnecting all existing electrical connection from panel ,taking out unserviceable MCCB and cable from the LT panel Board and Supply, fixing, connecting and testing of MCCB 250 Amp 4 pole 36 KA adjustable thermal setting (80 to 100 %) type415 V 50 Hz with spreader and suitable size of cable lugs/thimble complete incl all electrical connection with making good the damaged surface complete all as specified and directed by Engineer-in-Charge

Supplying,laying, fixing,jointing and testing LT under ground electric power cable crossed linked polyethylene ( XLPE) insulated, galvanised steel strip armoured, ISI-7098 Marked, with aluminium conductor multi stranded, heavy duty 1100 Volts grade of size 6 sqmm cross sectional area, 2 core laid in trenches/ laid under floor or fixed naked with walls/ on poles/ in ducts /in GI pipes etc. with and including MS clamps, nuts , bolts, washers complete all as specified and directed by Engineer-in-Charge Note :- Excavation, earth work, sand cushioning, protection bricks/ tiles/ block and pipe shall be measured and paid separately under respective items.

All as per item No 175 above but size 16 sq mm 4 core

All as per item No 175 above but but size 25 sq mm 4 core

All as per item No 175 above but but size 50 sq mm 3.5 core

All as per item No 175 above but but size 95 sq mm 3.5 core

All as per item No 175 above but but size 120 sq mm 3.5 core

All as per item No 175 above but but size 185 sq mm 3.5 core

Taking out old unserviceable LT cable from trench and relaying/rerouting the same after removing of defects any type/size in trenches / road crossing /through pipes pat drains/ducts/floors/along poles/walls/ceilings complete all as specified and directed by Engineer-in-Charge Note - excavation and earth work will be measured and paid seprately in appropriate item.

Plain cement concrete 1:3:6 type D-2 using 40 mm graded stone aggregates, as copping of poles complete all as specified and as directed by Engineer-in-Charge.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete all as specified and directed by Engineer-in-Charge

Protection to cable with one layer of bricks laid flat butting to each other in such a way that the length of the bricks is at right angle to the central axis of the cable using old size sub-class ‘B’ bricks complete all as specified and as directed by Engineer-in-Charge.

Boring / drilling (Horizontly ) manually under existing road Max 10 M in width ) suitable for passing GI tubing 40 to 100 mm bore complete all as specified and directed by Engineer-in-Charge

Disconnecting the cable from Panel / Pole, preparing the end for jointing including all earth work, Supply and fixing Cable end termination heat shrinkable joint inclding sleeves suitable for LT XLPE cable of size 4/3.5 core 25 to 50 sq mm complete all as specified and directed by Engineer-in-Charge.

All as per item No 187 above but size 70 to 185 sq mm

Disconnecting the cable from Panel / Pole, preparing the the cable end for jointing including all earth work, Supply and fixing straight through heat shrinkable joint suitable for LT XLPE cable of size 4/3.5 core 25 to 50 sq mm complete all as specified and directed by Engineer-in-Charge.

All as per item No 189 above but size 70 to 185 sq mm

S&F Mild steel galvanized tubes light grade ISI marked 40mm bore laid in trenches / road crossing/ fixed to pole /walls/path/drain/floor etc complete all as specified and directed by Engineer-in-Charge

All as per item No 191 above but 50 mm size

All as per item No 191 above but 80 mm size

Surface dressing/ cleaning of surrounding area of two pole/four pole structure / RMU /LT panel etc sub stn area ( 4 mtr X 4mtr ) including removing of tree branches complete all as specified and directed by Engineer-in-Charge

Dismantling of existing old damage PCC pole/ steel pole of any description complete all as specified and directed by Engineer-in-Charge

Supplying, transporting, erecting Steel tubular swaged poles type 410 SP-31 ( 9.0 metres long) complete with cast iron base plate, final, taper plug, bolts, nuts and screws as specified, including necessary excavation and earth work , PCC 1:4:8 type D2 in foundations below pole, PCC 1:3:6 type C2 around poles and PCC 1:3:6 type C1 as in plinth block , disposal of surplus soil to a distance not exceeding 50 m and depositing where directed, painting steel tubular poles exposed surafces with Aluminium paint two coats over one coat of red oxide primer and providing 300 mm wide bands (3 bands/ straps with synthetic enamel paint and 2 bands with Black bituminous paint ) from plinth block and numbering of poles , painting embedded portion of poles with one coat of bituminous paint complete all as specified and directed by Engineer-in-Charge

Preparation of old painted surfaces and painting of LT steel tubular pole 9 mtrs long from bottam to top with aluminium paint and painting to bottam up to 1.5 mtr height from top of PCC coping with sysnthetic enamel paint 2 coats in black and Yellow/white alternate strip including numbering in 8 cm height of number with white paint both paint aluminium /synthetic duly approved by engineer –in-Charge and complete all as specified and directed by Engineer-in-Charge

M & L for painting on old painted surface of LT Panel/Feeder Piller Box by Spray after cleaning stain & grease spot with thinner and sand papar and painting the cleaned surface with synthetic enamel paint as existing colour to acheive good finish by applying two coat paint by spray painting machine carefully after disconnection of power supply and covering the meters, indicators, relays and switches to prevent fall of paint drop on them & including writing, numbering, letter etc with white paint on newly painted surfaces complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs changeover switch triple pole with neutral link 320 amps 415 Volts AC, 50 Hz, complete existing system and cabling network including making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

S&F in replacement LED Indicator lamps (RYB) as per existing size complete all as specified and directed by Engineer-in-Charge

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode 32x6 mm earthstrip by means of bolts, nuts check nuts and washers of GI or steel and connecting to earthing test point, main switch board, testing on completion including PCC cover and frame, PCC (1:3:6) type C-2 as in earthing pit, MS funnel with wire mesh GI pipe 20 mm dia light grade for watering and GI pipe 20 mm dia light grade for the protection of GI wire from earth pit to earth point complete including necessary excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50 m all as specified as shown in electrical plate No 5 SSR Part-I. PCC chamber shall be constructed at least one metre away from the earth pit and GI pipe fittings for watering shall be provided up to chamber and cost of the same is deemed to be included in the rate of earthing.

Supply & fixing in replacement ISOLATOR 4P 100 Amp, 10 KA ,415 volts C curve complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement ISOLATOR 4P 63 Amp, 10 KA ,415 volts C curve complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement of LED street light fitting with mandatory driver set having pressure die cast aluminium body and lenses suitable for 45 watt conforming to IP 66 and IK 07 protection having company LOGO ingraved complete lumes high power LED with lenses Lumen efficacy of LED not less than 100 lumen per watt system,efficiency power factor >0.95, THD<10% at Full load CRI> 70%, every life class 50000 hrs at the L70,poted driver set suitable for pole mounting bracket 40 mm. All relevent documents related to luminaries and driver needed to submit for approval complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement of LED street light fitting with mandatory driver set having pressure die cast aluminium body and lenses suitable for 60 watt conforming to IP 66 and IK 07 protection having company LOGO ingraved complete lumes high power LED with lenses Lumen efficacy of LED not less than 100 lumen per watt system,efficiency power factor >0.95, THD<10% at Full load CRI> 70%, every life class 50000 hrs at the L70,poted driver set suitable for pole mounting bracket 40 mm. All relevent documents related to luminaries and driver needed to submit for approval complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement of LED street light fitting with mandatory driver set having pressure die cast aluminium body and lenses suitable for 90 watt conforming to IP 66 and IK 07 protection having company LOGO ingraved complete lumes high power LED with lenses Lumen efficacy of LED not less than 100 lumen per watt system,efficiency power factor >0.95, THD<10% at Full load CRI> 70%, every life class 50000 hrs at the L70,poted driver set suitable for pole mounting bracket 40 mm. All relevent documents related to luminaries and driver needed to submit for approval complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement of LED flood light fitting with mandatory driver set having pressure die cast aluminium body and lenses suitable for 120 watt conforming to IP 66 and IK 07 protection having company LOGO ingraved complete lumes high power LED with lenses Lumen efficacy of LED not less than 100 lumen per watt system,efficiency power factor >0.95, THD<10% at Full load CRI> 70%, every life class 50000 hrs at the L70,poted driver set suitable for pole mounting bracket 40 mm. All relevent documents related to luminaries and driver needed to submit for approval complete all as specified and directed by Engineer-in-Charge

Supply & fixing in replacement GI brackets made of 32/40 mm nominal bore GI pipe medium grade of required length not less than 1.5 M long, mounting brackets made out of Mild steel FI 40x6 mm of required shape ( two Nos) duly fitted with Mild steel nuts, bolts and washers and painting with two coats of synthetic enamelled paint over one coat of red oxide Zn chrome primer and fixed to pole / walls etc complete all as specified and directed by Engineer-in-Charge

Supply and fix PVC junction box weather proof IP-65 conform to EN 60439-3, recessed with wall/pipe surfaces by chase cutting and making good surfaces of wall complete all as specified and directed by Engineer-in-Charge

Supply and fixing new generation ,energy saving ,environment friendly LED post top lanterns fitting, aluminium spun lamdscape luminaires with high power LED as light sopurce including making connections complete all as specified and directed by Engineer-in-Charge

Supply and fixing new generation ,energy saving ,environment friendly LED post top lanterns fitting, aluminium spun lamdscape luminaires with high power LED as light sopurce including making connections complete all as per specified and directed by the Engr-in-Charge.

Material and labour for tubes, 'light grade', galvanised 50mm bore with all fitting laid in trenches/walls complete all as specified and directed by Engineer-in-Charge

M&L for Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregates as in foundation of GI pipes including finishing to exposed concrete surfaces even and fair and provision of necessary form work for rough finished surfaces complete all as specified and directed by Engineer-in-Charge

M K Engineers and Contractors

M/S S.B. Singh and Sons