REPAIR /REPLACEMENT OF LT CABLE NETWORK, TRANSFORMER, LT SWITCH GEARS / ACBs AND CONNECTED ITEMS AT ZONE-II AREA UNDER AGE E/M OF GE JAIPUR

Amount

M&L for Maint / servicing of Ring Main Unit (RMU) Out door type, 11KV 630 Amps, 4 way of electro mechanical componants at site etc. by cleaning,brushing & removing dust particals from body, isolating contacts, moving parts, particularly from bus bar chamber, gear mechanism, spring mechanism, tightening of nuts & bolts of all components in entire mechanism and re-connection to load, re-commissioning including consumables (Petrollium jelly) CRC, O ring, and make sure that brushings, cable plugs and gaskits are free of grease and polution including testing complete with replacement of following spare parts complete all as specified and directed by Engr-in-charge. Make: Crompton Greaves Note : Spare parts shall be measured as supply only under respective item of BOQ

Supply only Silicon Grease Grade 50

Supply only 1.1 kv straight throught cable joint kit of size 300 Sqmm 3.5 core complete.

Supply only Contact mechanism piece

Supply only 11 KV straight throught cable joint kit 240 Sqmm 3 core

Supply only Vertical Cable termination boot (Indore type)

Supply and fixing in repair transformer breather assembly oil seal type made of heavy duty transparent plastic body having top & bottom cover made of aluminium or mild steel of capacity 500 grams filled with silica gel complete all as specified and directed by Engr-in-charge.

M&L for topping up of deficient oil level of transformers with filtered and dehydrated transformer oil (conforming to IS: 335) and to withstand dielectric strength 60 KV or above (when tested with 2.5 mm gap electrode) complete all as specified and directed by Engr-in-charge. Make - Savita / Powerlink / Poweroil or equivalent as approved by GE

S&F in repair HV brass set stem of 12 KV grade suitable for transformer of capacities 200 KVA to 400 KVA as required complete all as specified and directed by Engr-in-charge.

S&F in repair LV brass set stem of 1.1 KV grade suitable for transformer of capacities 200 KVA to 400 KVA as required complete all as specified and directed by Engr-in-charge.

Dehydration / Filtration of transformer Oil of existing transformer install at site with portable plant to improve the dielectric strength 40 to 60 KV during filling after initial filtration including testing of dielectric strength after dehydration at site complete all as specified and directed by Engr-in-charge.

M&L for opening up the top cover of transformer of any capacity for checking the conditions to carryout repairs at site, including draining out oil from the transformer in suitable containers (containers to be provided by the contractor) and repair the transformer with replacement of parts where required, check the lead connection from winding to bushing rods including necessary soldering/jointing etc and refilling the dehydrated oil after complete repair, making all connections and testing on full load complete all as specified & as directed. Notes :- (i) Labour component required for the replacement of unserviceable parts shall deemed to be included in the unit rate quoted against this item. (ii) Major parts where required to be replaced shall be measured and paid for separately as ‘Supply only’ under relevant items of this Schedule. (iii) All T&P and minor parts such as nuts, bolts, washers, insulating material, copper wire for delta connection, etc. shall be arranged by the contractor and the cost thereof shall be deemed to be included in the unit rate quoted against this item. (iv) Dehydration of existing transformer oil and new transformer oil required for topping up shall be measured and paid for separately under relevant items of this Schedule.

Supply & fix in repair HT bushing as per existing and as per manufacturers instruction complete with double check nuts, washers, gasket set for transformer of capacity 200 KVA complete all as specified and as directed.

Supply only HT bushing as per existing and as per manufacturers instruction complete with double check nuts, washers, gasket set for transformer of capacity 315 KVA to 400 KVA complete all as specified and as directed.

Supply only LT bushing with brass spindle as per existing and as per manufacturers instruction complete with double check nuts, insulation washers for transformer of capacity 200 KVA complete all as specified and as directed.

Supply only LT bushing with brass spindle as per existing and as per manufacturers instruction complete with double check nuts, insulation washers for transformer of capacity 315 to 400 KVA complete all as specified and as directed.

Supply only Gasket set made of rubberised cork/neoprene material for transformer of capacity 200 KVA complete all as specified and as directed.

Supply only Gasket set made of rubberised cork/neoprene material for transformer of capacity 315 KVA to 400 KVA complete all as specified and as directed.

M&L for disconnecting existing transformer step down 11 KV/0.433 KV indoor/outdoor type of capacity 200 KVA, taking down from site of installation, opening the top cover of transformer, draining out transformer oil from the housing in suitable containers (containers to be provided by the contractor) and deposit the oil in store yard of AGE MFFR, inspecting / assessing the defective / burnt parts, core assembly, etc in the presence of Engineer-in-Charge, shifting the transformer to workshop for repair including loading, unloading, transportation etc, cleaning and making good surface including internal cleaning, removing sludge, etc and painting with one coat of zinc chromate paint to the inner side of the transformer body and one coat of synthetic enamel paint (grey) on outer body of transformer by using spray machine after cleaning & removing oil spots etc, carrying out necessary repair to transformer at workshop, re-assembling, shifting back to site, reinstalling, re-connecting, re-commissioning the transformer and testing at site on full load, complete all as specified and as directed.

,---Ditto--- all as per item no 14 above but for Transformer of capacity 315 to 400 KVA complete.

Supply only the following spares/items for repair/replacement to transformers under serial item No. 14.00 to 15.00 here-in-before :- (a) LT coil made out of super enameled copper conductor wire of suitable gauge and size as per requirement for distribution transformer complete all as directed.

(b) HT coil made out of super enameled copper conductor wire of suitable gauge and size as per requirement for distribution transformer complete all as directed.

S&F in repair 11000 volt grade heavy duty HT XLPE cable with PVC insulated aluminum conductor served with inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 120 Sqmm nominal cross section 3 core laid in trenches, fixed to pole or passing through pipes including all necessary clamps, nuts, bolts washers complete all as specified and directed.

S&F cable jointing kit for 11 KV (Earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 to 185 sqmm 3 core complete all as specified and directed.

Material and labour for fault investigation of HT /LT electic supply line of any size with fault lacator machine for LT / HT line including rectification of fault with cutting/disconnecting of cable and jointing with suitable size of cable jointing kit, excavation or as speciffied and as directed.

Providing area cleaning/sweeping of preimises and clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees n exc 30 cm girth (measured one metre above ground level) and maintaining the ground surrounding transformers, LT Panels, 02 Pole structures, 04 Pole Structures, etc at various sub stations / E&M installations and removing the same out side the defence area as directed by Engr in charge. Notes for serial item No: 2.00 to 20.00 :- (i) Labour component required for the replacement of unserviceable parts shall deemed to be included in the unit rate quoted against this item. (ii) HT/LT coils where required shall be measured and paid for separately as ‘Supply only’ under relevant items of this Schedule. (iii) All minor parts such as nuts, bolts, washers, insulating material, copper wire for delta connection, etc. shall be arranged by the contractor and the cost thereof shall be deemed to be included in the unit rate quoted against this item. (iv) Testing of transformer shall be arranged by the contractor for Type Test & Routine Test which shall be carried out in the presence of Engineer-in-Charge and contractor shall submit test certificates to this effect before processing the RAR for payment.

M&L for taking out old unservicable LT cable of any size from trenches complete all as specified and directed

S&F 1100 volt grade heavy duty XLPE cable with PVC insulated aluminum conductor served with inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 400 Sqmm nominal cross section 3.5 core laid in trenches, fixed to pole or passing through pipes including all necessary clamps, nuts, bolts washers complete all as specified and directed.

,---ditto--- all as per srl item No. 23 above but cable of size 300 Sqmm nominal cross section 3.5 core complete.

,---ditto--- all as per srl item No. 23 above but cable of size 240 Sqmm nominal cross section 3.5 core complete.

,---ditto--- all as per srl item No. 23 above but cable of size 185 Sqmm nominal cross section 3.5 core complete.

,---ditto--- all as per srl item No. 23 above but cable of size 120 Sqmm nominal cross section 3.5 core complete.

,---ditto--- all as per srl item No. 23 above but cable of size 95 Sqmm nominal cross section 3.5 core complete.

,---ditto--- all as per srl item No. 23 above but cable of size 70 Sqmm nominal cross section 3.5 core complete.

,---ditto--- all as per srl item No. 23 above but cable of size 50 Sqmm nominal cross section 3.5 core complete.

,---ditto--- all as per srl item No. 23 above but cable of size 35 Sqmm nominal cross section 3.5 core complete.

,---ditto--- all as per srl item No. 23 above but cable of size 16 Sqmm nominal cross section 4 core complete.

,---ditto--- all as per srl item No. 23 above but cable of size 10 Sqmm nominal cross section 4 core complete.

S&F in repair galvanised steel tubes "light grade " of 80 mm bore (ISI marked) with all fitting (ISI marked) and fixed to walls and ceilings or laid in floors/ trenches and under road complete all as specified and directed.

,---ditto--- all as per srl item No. 34 above but tube of 100 mm size complete.

Excavation in trenches not exceeding 1.5 m wide and but exceeding 1.5 m in depth upto 3.00 mtr and getting out in soft/loose soil for laying of cable or foundation etc. complete all as specified and as directed.

Returning, filling including spreading leveling watering and well ramming in layers n. exc 25 cm in soft/loose soil complete all as directed.

Removing excavated soil to a distance n. exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as directed.

M & L Sand cushioning to under ground cable with screened and washed sand (non cohessive), 8 cm before laying cable and 15cm after laying and punned to 18cm after laying of cable complete all as specified and directed by Engineer-in-Charge. Note : Punned thickness shall be considered for payment purpose.

Supplying and laying un-reinforced precast cable covers class HV, type I, flat, size 300mm x 180mm x 40mm complete all as specified and as directed.

M & L bricks for protection cover to UG cable (with old size sub class B bricks) with width equal to length of brick, laid dry and flat abutting each other with gaps between adjecent bricks not exceeding 10mm complete all as specified and directed.

S&F in replacement of digital voltmeter of suitable range including wiring with copper conductor cable of suitable size all as specified and as directed by Engineer-in-Charge.

S&F in replacement of digital ammeter of suitable range including wiring with copper conductor cable of suitable size all as specified and as directed by Engineer-in-Charge.

S&F in rewiring of LT panel/feeder of any size including replacemnt of wornout parts , nut , bolts,backlite surface and cleaning of burnt/rusted surface/ all as specified and as directed by Engineer-in-Charge.

M&L for preparation of the old painted surfaces of feeder piller boxes/panels/boards / transformer of any size any description and in any position including removal of faded & deteriorated paint eaither by hand scrapping or by blow lamps, applying necessary filler coat and scrapping as required and applying two coats of synthetic enamelled paint (grey in colour) with using spray machine complete all as spcified and as directed by Engineer- in Charge.

Supply and fixing in replacement danger notice plate of size 20x15cm made out of MS sheet 1.6 mm thick, vitreous enameled white, with letters figures and conventional skull and bones in signal red colour and fixed with MS clamps, bolts, nuts on LT poles complete all as directed by Engineer-in-Charge.

M&L for cable jointing kit for upto 1.1 KV (Earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 35 sqmm 3.5 core XLPE armoured aluminium conductor cable complete all as directed by Engineer-in-Charge.

,---ditto--- all as per srl item No. 47 above but suitable for cable of 50 sqmm 3.5 core size complete.

,---ditto--- all as per srl item No. 47 above but suitable forcable of 70 to 120 sqmm 3.5 core complete.

,---ditto--- all as per srl item No. 47 above but suitable forcable of 240 to 300 sqmm 3.5 core complete.

,---ditto--- all as per srl item No. 47 above but suitable for cable of 400 sqmm 3.5 core complete.

M& L for shifting of existing LT Panel disconnecting existing electrical connection from MCCBs / MCB / Bus bar, taking out required length from loop of cable and reconnecting with electrical connection at new location including breaking / cutting existing PCC foundation and fixed at new location in PCC 1:3:6 using 20 mm graded stone aggregate incluting paitning with danger sign on Panel not beyond 300 mtr or as specifiied by the Engr In Charge

M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.25mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to GI strip of size 32x6mm by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI strip upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.25mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to GI lead wire 4.0mm dia by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

S&F in repair of MCCB 63 Amps, 4 pole,415V, 16 KA (Ics=100% Icu) thermally adjustable between 70% to 100% with spreader links on both sides complete all as directed by Engineer-in-Charge.

Supply and fixing in repair of MCCB 125 amp, 4 pole, 16 KA (Ics=100% Icu) thermally adjustable between 70% to 100% with spreader links on both sides complete all as directed by Engineer-in-Charge.

Supply and fixing in repair of MCCB 160 amp, 4 pole, 16 KA (Ics=100% Icu) thermally adjustable between 70% to 100% with spreader links on both sides complete all as directed by Engineer-in-Charge.

Supply and fixing in repair of MCCB 250 amp, 4 pole, 25 KA (Ics=100% Icu) thermally adjustable between 70% to 100% with spreader links on both sides complete all as directed by Engineer-in-Charge.

Supply and fixing in repairl of MCCB 400 amp, 4 pole, Icu 36 KA (Ics=100% Icu), electronic release and adjustable between 40% to 100% with spreader links on both sides complete all as directed by Engineer-in-Charge.

Supply and fixing in repair of MCCB 630 amp, 4 pole, Icu 50 KA (Ics=100% Icu), electronic release and adjustable between 40% to 100% with spreader links on both sides complete all as directed by Engineer-in-Charge.

M&L for street light junction box made out of 2 mm thick MS sheet of size 250x200x150 mm incl 04 nos aluminium busbar of size 20x3 mm thick mounted on porcelain insulators and one MCB SP 6 amps etc having provn of cable glands for incoming and outgoing cables, fixed to pole with proper fixing arrangement and painting complete all as specified and directed.

M & L for maint/servicing of AMF panel of any make model and repair of unsv wiring of size (A-Z,0-9) including cleaning resetting / adjustment of relays, calibration of timing, relays, conract checking and replacing following parts etc as specified and as required of existing make for for 250 KVA DG set complete all as specified and directed. Note : Parts shall be measured and paid seperately as supply only

Supply only Advanced AMF controlled unit GCU for (Genset controller unit) for RPM, LLOP / LO battery, low water, low fuel, HTC, V belt safety etc of existing make for AMF panel of 250 KVA DG set complete all as specified and directed.

Supply and fix in repair 4 pole Power contactor, 415 V ,400 Amp alongwith complete new wiring in existing panel complete all as specified and directed by Engr-in-charge.

Supply and fix in repair 3 pole contactor, suitable for 415 volt, 160 Amp alongwith complete new wiring in existing panel complete all as specified and directed by Engr-in-charge.

Supply and fixin repair 3 pole contactor, suitable for 415 volt , 255 Amp alongwith complete new wiring in existing panel complete all as specified and directed by Engr-in-charge.

Supply and fix in repair 3 pole contactor, suitable for 415 volt, 63 Amp alongwith complete new wiring in existing panel complete all as specified and directed by Engr-in-charge.

M&L for of wall mounted 6 Way bus bar chamber connsisting with bus bar 3 phase and neutral 4 Nos 200 Amp fixed on insulators including fixing in wall or as specififed by engineer in charge Make : Havells cat part No IHBC020006 or equivalent in Legrand/ L&T / BCH as approved by GE.

S&F in repair MCB distribution board, tripple pole and neutral (VTPN) powder coated CRCA steel sheet suitable for MCCB incomer upto 160 amp, 4 way, 415 volts, degree of protection IP 43 - IK- 09 with reversible double door, recess mounted, having 250 amp insulated tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required. Note for MCBs & MCB DBs:- MCCBs, MCBs & MCB DBs shall be of the same make.

S&F MCBs Single pole 6 to 32 amp of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed by Engr-in-charge.

,---ditto--- all as per srl item No. 71 above but MCB double pole 10 to 32 amp complete

,---ditto--- all as per srl item No. 71 above but MCB Double pole, 40 to 63 amp complete

,---ditto--- all as per srl item No. 71 above but MCB Four pole 40 to 63 amp complete

M&L for cross arms, bracings, supports, clamp and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot drilling holes for bolts in any shape or size as indicated or directed and inclusive of one primer coat one under coat and one finishing coat of paint complete all as specified and directed.

S&F LED flood light 70 watt, 230 V AC highly efficient integral type mid power made of pressure die cast aluminium housing with 10KV SPD toughened glass w/o lens, outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.

S&F LED flood light 100 watt, 230 V AC highly efficient integral type mid power made of pressure die cast aluminium housing with 10KV SPD toughened glass w/o lens, outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.

S & F in repair LED street light 70 watt including driver with a nominal system lumen output of 7200 lumens and a minimum system efficacy of 100 lumen/watt. The luminaire shall have rated system lifetime of 50,000 burning hours before reaching at L70. The luminaire should have cool white colour temperature (CCT > 5000K) and a CRI >70. The luminaire shall meet IP 66 rating & IK05 rating with THD < 20% and PF > 0.9. The luminaire housing should be made of pressure die cast aluminium with a flat glass optical cover complete all as specified and directed.

S&F flexible copper conductor cable of size 4 Sqmm 3 core in PVC conduit for lighting connection and all as specified and directed.

M&L for preparation of old painted street light poles 8.5 m / 9.0 long including street light brackets/clamps etc and painted with best quality aluminium paint, making alternate black & white colour bands of 30 cms width upto a height of 1.5 m from pole coping with synthetic enamelled paint and writing pole numbers in black colour on yellow base complete all as specified and directed.

S&F in repair for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25x4mm galvanised iron strip and all as per directed.

S&F in repair air termination, single pointed, copper rod 12mm dia and 300mm long with all accessories required for fixing/mounting on 20mm GI pipe including taking down old unserviceable and make good the disturbed surface complete all as specified and as directed. Note: GI pipe 20mm dia measured and paid seperately

S&F in repair single aluminium strip of size 25x3mm in proper posion with saddles and fixing screws for roof conductors and down conducrors from top to the building air termination point to the test points of the building as required after and including taking out old unsv and make good the disturbed surface complete all as specified and directed.

S&F in repair for test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw and connected with earthing strip including taking out old unsv and make good the disturbed surface complete all as per directed.

S &F electric shock treatment chart printed on A1 size paper duly plastic laminated and fixed inside a wooden/PVC photo frame of 50 mm width with 3 mm sheet glass and 6 mm plybood backing and suitable hanging arrangement to wall with hooks/steel chain etc, including taking down old U/S one complete all as specified and directed by Engineer-in-charge.

S &F First aid chart printed on A1 size paper duly plastic laminated and fixed inside a wooden/PVC photo frame of 50 mm width with 3 mm sheet glass and 6 mm plywood backing and suitable hanging arrangement to wall with hooks/steel chain etc, including taking down old U/S one complete all as specified and directed by Engineer-in-charge.

S &F electric Fire safety chart printed on A1 size paper duly plastic laminated and fixed inside a wooden/PVC photo frame of 50 mm width with 3 mm sheet glass and 6 mm plybood backing and suitable hanging arrangement to wall with hooks/steel chain etc, including taking down old U/S one complete all as specified and directed by Engineer-in-charge.

S&F in replacement name board of transformer and DG sets on ACP sheet of size 2 feet X 3 feet with matter indicating capacity, date of installation, SM/MES No., Make/Model and other maater directed by Engr-in-charge complete all as specified and directed. Note: The matter to be printed has to be approved from Engr-in-Charge before final printing

M&L for painting of transformer 200KVA by applying two coats of synthetic enamel paint of grey colour by spraying complete including prepration of old surface, removing & cleaning of oil / grease etc complete all as specified and directed.

M&L for painting of transformer 315KVA by applying two coats of synthetic enamel paint of grey colour by spraying complete including prepration of old surface, removing & cleaning of oil / grease etc complete all as specified and directed.

M&L for painting of transformer 400KVA by applying two coats of synthetic enamel paint of grey colour by spraying complete including prepration of old surface, removing & cleaning of oil / grease etc complete all as specified and directed.

M&L for boring of existing road/PCC path for laying of GI pipe of size 80 to 100mm dia for protection of UG cable including making good the disturbed area with PCC 1:2:4 complete all as specified and as directed

M&L for PCC (1:3:6) type C2 using 40 mm graded aggregate for base / foundation/ earthing chamber / chamber cover etc including form work complete all as specfied and directed .

M&L PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping including nacessary form work complete all as specified and as directed.

S&F in replacement transformer oil temperature gauge suitable for transformers of capacity 200 to 400KVA complete all as specified and as directed.

S&Fin repair Air break switch 200 amp, for HT 11 KV, 50 Hz AC, Gang Operated, triple pole, outdoor, horizonal / vertical mounting type (ISI marked), mounted on insulators and MS frame work, with fuse carriers & HT fuses, manually operated from ground level with locking arrangment including 65 mm pad lock with two keys, necessary electric connections, taking down old item complete all as specified and directed by Engineer-in-Charge..

S&Fin replacement of changover switch 400 Amp, 415 volts, 4 pole of onload with sheet steel enclouser suitable for existing panel complete all as specified and directed.

Note:- (a) Material like MCB, MCCB, ACB, Cable, contactor etc shall be procured in one time, of approved make by authorized dealer of manufacturers ad manufacturer test certificate of (where applicable) shall be submitted before claiming payment (b) The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

SHREE BHAGWATI ENTERPRISES (BID ID -3498418)