PROVN OF TOILET BLOCK FOR CIVILIAN STAFF AT CTW ADDN/ALTN TO TOILET CUM WASHROOM OF BLDG NO T-3 PROVN OF BOUNDARY WALL BEHIND OFFICERS MESS AND PROVN OF MESH COVER METAL GATE AND FENCING AT GARBAGE DISPOSAL PITS IN MCEME UNDER GE MCEME SECUNDERABAD

Amount

Excavation in trenches n exc 1.5m wide and not exc 1.5m depth; for foundation, etc not exc 10 sqm on plan and getting out in hard/dense soil complete all as specified and directed by Engineer-in-charge.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm in hard/dense soil complete all as specified and directed.

Removal of excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above starting point complete all as specified and directed.

M&L for treating the top surfaces of filled earth at the rate of 5 litre of emulsion per sqare metre of surface area complete all as specified and directed.

M&L for treating the soil under plinth protection at the rate of 5 litre of emulsion per sqare metre of surface area complete all as specified and directed.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per sqare metre of perimeter wall complete all as specified and directed.

M &L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation /mass concrete for footing and steps complete all as specified and directed.

M&L for formwork to fair finished surfaces of sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for RCC Type B1 1:1.5:3 ( 20mm graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for formwork to fair finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for RCC Type B1 1:11/2:3 ( 20mm graded stone aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for formwork to fair finished surfaces of timber form work to sides and soffits of floor or roof beam , lintels including support , overhangs etc also splays between floors and beams etc. complete all as specified and directed.

M&L for RCC Type B1 1:1.5:3 ( 20mm graded stone aggregate) in beams, cantilevers,bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for form work to chajjas, and similar work including edges for fair finished surfaces complete all as specified and directed.

M&L for RCC Type B1 1:1.5:3 ( 20mm graded stone aggregate) in Chajjas complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick complete all as specified and directed.

M&L for RCC Type B1 1:1.5:3 ( 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-charge.

M&L for TMT bar 10 mm dia and over cut to length bent to shape required, including cranking, bending, spirally for hooping for column hooking ends and binding with and including mild steel steel wire (annealed ) not less than 0.90 mm dia or seccuring with clips quility confirming to Deformed or twisted bars complete all as specified and directed by Engineer-in-charge.

M&L for TMT bar 6mm to 8mm dia and over cut to length bent to shape required, including cranking, bending, spirally for hooping for column hooking ends and binding with and including mild steel steel wire (annealed ) not less than 0.90 mm dia or seccuring with clips quility confirming to Deformed or twisted bars complete all as specified and directed by Engineer-in-charge.

Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6 Mtr mean radius built in CM 1:6 complete all as specified and directed.

M&L Brick work with fly ash bricks, straight or curved on plane to any radius but in half thick built in CM 1:4 complete all as specified and directed.

M&L for Rendering 15 mm thick cement plaster on fair faces of brick work/concrete in cement mortar 1:6, with water proofing compound finished even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 10 mm thick cement plaster on fair faces of brick work/concrete in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling, complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

M&L for preparation of new plaster surface of wall and applying two coat of white wash over a coat of primer complete all as specified and directed

M&L for preparation of new plaster surface of wall and applying two coat of cement base paint over a coat of primer complete all as specified and directed

M&L applying two coats of white wash, over a coat of primer on new ceiling surface including preparation of surface, complete all as specified and as directed by Engineer-in-Charge.

M&L for Moorum/approved earth filling in floors or pavings laid in layers n.exc 15 cm thick spread levelled and rammed including watering complete all as specified and directed.

M&L Hardcore guage exc 63 mm n.exc. 100 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rolled / rammed to a true surface.brocken stone or boulders complete all as specified and directed.

M&L for cement concrete 75mm thick Type D-2 1:4:8 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L cement concrete type B1, 1:2:4 (20mm graded stone Aggregate) 40 mm thick in floor finished fair and smooth without using extra cement complete all as specified and directed.

M&L Rendering 10mm thick in cement mortar 1:4 finished fair complete all as specified and directed.

M&L screed bed or bedding layer of cement mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L for Non - skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surfaces 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in floor / plinth protection including finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:3) using water proofing compound as per manufacturer instructions as in roof padding and chajjas complete all as specified. Note : Water proofing compound will be measured and paid separately complete all as specified and directed.

M&L for APP modified prefabricated five layer water proofing membrane minimum 3mm thick and weighing not less than3.6 kg/Sqm, reinforced with non woven polystester matt black finished (wt not less than150 gms/Sqm) over combatible primer at 0.40 Ltr/Sqm and torch applications of membrane with minimum 10cm side over lap and 15cm end laps and applying solar reflective bituminous aluminium paint @ 0.10 kg / sqm complete all as specified and as directed by Engineer-in-Charge.

S&F Solid PVC Door Frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification & drawing complete all as specified and directed by Engineer-in-charge.

S&F Aluminum anodised, barrel tower bolts of extruded section and fixed of 150 mm long complete all as specified and directed.

S&F Aluminum alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast - aluminum alloy and fixed of 300mm long complete all as specified and directed.

S&F Butt hinges, 100 mm long extruded aluminium alloy with galvanisedmild steel hinge pin, anodised and fixed, type c-21 complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised,150mm long complete all as specified and directed.

S&F steel windows/ventilator with slide/top hung shutters inculding box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and as directed by Engineer-in-Charge.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

M&L for two coats of synthetic enamel paint over and including a coat of red oxide including preparation of new or previously untreated steel surfaces over 10cm in width or girth, not otherwise described in any pattern complete all as specified and directed.

S&F GI pipe medium grade galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors 15 mm bore medium grade pipe complete all as specified and directed.

S&F GI pipe medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors 20 mm bore complete all as specified and directed.

S&F GI pipe medium grade galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors 25 mm bore complete all as specified and directed.

S&F PVC ( SWR) soil waste pipe in any length Single socketed with rubber ring joints laid in trenches or in floors 110mm dia bore of pipe ISI marked complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in trenches or in floors, including necessary brackets complete all as specified and directed.

S & F PVC (SWR) gully trap 125 / 110 mm including setting and jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) floor trap, plain with Chromium plated grating including jointing with solvent cement with 75 mm outlet dia complete all as specified and directed by Engineer-in-charge.

S&F PVC (SWR) bends any radious 75mm bore complete all as specified and directed.

S&F viterous china wash hand basin, white flat back size 550mm x 400 mm including Mild Steel brackets with waste fittings and waste pipe including cutting for and pinning in ends of brackets or erecting stand with grating fixing to floor making good complete all as specified and directed.

S & F fancy typ Pillar taps 15mm dia cast copper alloy with capstion heads, chromium plated , fancy type screwed down high pressure, with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts screwed for 15mm dia pipe complete all as specified and directed.

S&F fancy type stop valve cast copper alloy 15mm bore chromium plated with long shank and cup (concealed type) screwed for both ends for iron pipe or PVC pipes and fixed complete all as specified and directed.

S&F 15mm dia bib taps, chromium plated fancy type, cast copper alloy with fancy type handle , screwed down , screwed for iron pipe or for brass ferrule with wall flange, complete all as specified and as directed

S & F PVC connection 15mm dia 450 mm long with 2 Nos brass check nuts with washer etccomplete all as specified and directed by Engineer-in-charge.

S& F vitreous china squatting pan , 'orissa' pattern, size 580 X 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe ) including connection to trap, and to flushing pipe ,antisyphonage pipe, etc. complete includig making good to floor complete all as specified and directed.

S&F Vitreous China female squatting pan urinal of size 450 x 350 x 100 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and as directed by Engineer-in-Charge.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and as directed by Engineer-in-Charge.

M&L Granite (of any type) tiles 20mm thick machine cut, with grey cement slurry & pointed with white cement with admixure of pigment to match the shade of granite stone including cutting & polishing types for urinal partition complete all as specified and directed.

S&F Stainless Steel soap dish, any type, fixed to plugs with chromium plated brass screws, complete all as specified and directed by Engineer-in-Charge.

S & F PVC (SWR) 'P' trap dia out let is 110 mm complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

Material and Labour Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches, Bore of pipes in 40mm, complete all as specified and directed by Engineer-in-Charge.

S&F CP brass tubular towel rail 600mm long 20mm dia 'D' type complete all as specified and as directed by Engineer-in-Charge.

S&F Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge.

S&F PVC valveless, syphonic action type flushing cistern low level, white, with inlet, ball valve, float and handle incl brackets capacity 10 ltrs and connection to pipe complete all as specified and directed by Engineer-in-charge.

Material and Labour Grating 100 mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed by Engineer-in-Charge.

S& F brass chromium plated shower rose 125mm size with shower arm 15 mm size,195mm long with bend of 45degree with flange of PTMT any colour . (Minimum weight 40gms) complete all as specified and directed by Engineer-in-Charge.

M&L Rotational moulded polyethylene water storage tanks 1000Ltr three layered (cylinderical vertical with closed top) including dismantling water tanks and also necessary float ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed .(Minimum weight 20mm - 210 gms) hoisted and fixed in position , complete all as specified and directed by Engineer-in-Charge.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out as in hard/dense soil ccomplete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete 1:2:4 type B1 ( using 20 mm graded aggregate) in , copings, haunching and benching the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engineer-in-Charge.

M&L precast cement concrete type B1 1:2:4 type B1 (20mm graded aggregate) as in Manhole / Gully trap cover slab including use and waste of necessary form work set in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for Rendering 15 mm thick cement plaster on fair faces of brick work/concrete in cement mortar 1:4, with water proofing compound finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for 150 mm dia bore reinforced concrete pipes, class NP2, laid in trenches and jointed complete with collars complete all as specified and directed by Engineer-in-Charge.

M & L for cement concrete 1:4:8 type D2 to bed to drain pipe including packing under and hunching against sides of pipes after they are laid and tested for 150 mm dia pipe complete all as specified and directed by Engineer-in-Charge.

Cutting into existing manhole for connecting new drain, making good pipe and rending cutting out existing benching for and forming branch channel (1/2 round or 3/4 sec ) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 160mm dia complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm thick screed bed or bedding layer of mortar in cement 1:6 for laying floor finishes complete all as specified and directed by Engineer-in-Charge.

M&L chequered cement concrete tiles 30cm x30 cm x25mm thick , set jointed and pointed in neat cement slurry with grey cement and pigments complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in copings around thepaver block for setting etc including weathering, slightly rounded or chamfered angles and throating and including necessary form work complete all as specified and as directed.

Demolition of brick work or stone masonry built in cement mortar including pillar etc. complete all as specified and directed by Engineer-in-charge.

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6 Mtr mean raius built in CM 1:4 complete all as specified and directed by Engineer-in-charge.

Forming jambs, etc. in cement mortar 1:6 to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and directed by Engineer-in-charge.

Cutting opening in cement concrete walls, with or without reinforcement (any description) for door, window and other openings (with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering, etc. complete all as spd and directed.

M&L precast cement concrete type B1 1:2:4 type B1 (20mm graded aggregate) as in lintel band incl necessary form work set in CM 1:4 complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster or cement lime plaster of any description including racking out joints and hacking for key and scrubbing down with water complete all as specified and directed by Engineer-in-charge.

M&L for Rendering 10 mm thick cement plaster on fair faces of brick work/ concrete in cement mortar 1:4, rough finished complete all as specified and directed by Engineer-in-charge.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by Engineer-in-charge.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc ofFe 410 -W (Gde E- 250) quality A complete all as specified and directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/ ridge/ velley gutters and fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

Dismantling of ceiling boards of any description and any thickness, fixed in any position including cover fillets if any , complete all as specified and as directed by Engineer -in-Charge.

S&F anodised aluminium snap grid of 605 X 605mm frame work for false ceiling including hangers 3 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and xpansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed by Engineer-in-charge.

M&L for 6 to 7 mm thick gypsum board panels 600 x600 mm with PVC laminated on one side and aluminium foil on another side suitably placed in false ceiling grid made of aluminium Gi/MS all as specified and as directed. Note : Aluminium grid will be measured and paid separately.

M&L for applying two coats of OBD over two coat of wall care putty over a coat of alkali resistant primer including preparing the new plastered wall surfaces complete all as specified and directed by Engineer-in-charge.

Demolition of Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Taking down chowkhats of frames with shutter without taking taking off shutters from the frames n. exc 1.5 sqm but not exc. 04 sqm complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats of frames with shutter without taking taking off shutters from the frames not exc. 1.5 sqm complete all as specified and directed by Engineer-in-charge.

Dismantling of floor, hearth or wall tilling incl cement mortar bedding (but not backing) and removing the rubbish off the premises complete all as specified and as directed by Engineer -in-Charge.

M&L for Rendering 10mm thick in cement plaster 1:3 on brick wall surfaces for fixing tiles complete all as specified and directed by Engineer-in-charge.

M&L screed bed or bedding layer of mortar 15mm thick in cm 1:4 for laying floor finishes complete all as specified and directed by Engineer-in-charge.

Taking up or down, 15mm dia bore, GI tubing, medium grade, including removal from site, complete all as specified and as directed by Engineer-in-Charge.

Taking up or down, 20mm dia bore, GI tubing, medium grade, including removal from site, complete all as specified and as directed by Engineer-in-Charge.

S & F 15mm dia. Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe all as specified and directed.

S & F 20mm dia. Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed by Engineer-in-charge.

S&F in repair 110mm bore PVC (SWR) pipe single socketed,in any length with rubber ring joints, fixed to wall, complete all as specified & directed by Engr-in-Charge.

S&F in repair 75mm bore PVC (SWR) bend with oval access doors, complete all as specified & directed by Engr-in-Charge.

S&F in repair for PVC (SWR) bends any radius, bore of pipe in 110mm, etc, complete all as specified & directed by Engr-in-Charge.

S & F PVC (SWR) floor trap, plain with Chromium plated grating including jointing with solvent cement with 75 mm outlet dia all as directed by Engr-in-charge.

S&F PVC (SWR) bends any radious 75mm bore complete all as specified and directed by Engineer-in-charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern) white includig fixing bolts (excluding flushing cistern and flushing pipe) with Plastic water closet seat, black/white, closed pattern with flat bottom and cover including mild steel chromium plated aluminiged hinging device and making good disturbed surfaces with cement mortar1 :3 complete all as specified and directed by Engineer-in-charge.

S&F Vitreous China Urinal, Half stall type, white all as specified including flushing pipe and waste pipe in repairs complete all as specified and directed by Engineer-in-charge.

Excavation in post holes each n exc 0.50m getting out returning filling and remaining earth or broken rubble mixed with earth around in layers n exc 25cm getting out in hard/dense soil complete all as specified and directed by Engineer-in-charge.

S&F Mild steel angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling hole including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E 165 complete all as specified and directed by Engineer-in-charge.

M & L for PCC (1:3:6) type C2( using 40mm graded stone aggregate) as in foundation, filling and mass concrete etc. complete all as specified and directed by Engineer-in-charge.

Supply only chain link fenching of size 75x75 mm mesh of cages with 3.15 to 4 mm dia Mild Steel Galvanised Wire, complete all as specified and as directed.

Fixing only Chain Link Fencing 75X75mm Mesh or Cages with 3.15 to 4 mm dia Mild Steel Galvanised Wire lapped, Straining and Binding with including Mild Steel Wire (annealed) not less than 0.9 mm dia, complete all as specified and as directed.

M&L Mild Steel Flat as in Bands, etc. to Fencing Post with Ends of Bar shouldered and/or riveted or forged into Spikes, Framed Guard Bars and Similar Work, etc. conforming to Fe-410-0 or Fe-310-0 including all necessary drilling, bolting or riveting, etc., complete all as specified and as directed.

M&L Mild Steel Screw Bolts (Machine Made) with Hexagonal Head at one End and screwed the other Ends, each screwed End to be fitted with Washers and One Hexagonal Nut, diameter of Shank 5 to 10mm Length of Bolt exc. 100mm but not exc. 150mm, complete all as specified and as directed.

S&F welded Steel wire fabric of 5 mm dia and mesh size 50x50 ,complete to wood or steel members etc complete all as specified and directed.

Material and labour for concealed point wiring with single core PVC insulated unsheathed 1100 volt grade cable with multistranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked of suitable dia conduit concealed wiring including Tee, Junction boxes and provision of 2.0mm thick MS terminal boxes duly painted with red oxide metal primer and covered with 3 mm thick sheet cover of suitable size including suitable screws with washer for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to common earth dolly including cutting and chassing of wall complete all as specified & as directed for One light point controlled by one, one way switch 5 amps, SP complete all as specified and directed by Engineer-in-Charge.

All as per item No. 128 above but for One exhaust fan point controlled by one, one way switch complete all as specified and directed by Engineer-in-Charge.

All as per item No. 128 above but using 4.0 Sqmm single core copper conductor cable multistranded PVC insulated unsheathed 1100 volts grade for 3 pin 15 Amps switch socket combination point including running 4.00 Sqmm copper conductor PVC wire as earth continuity conductor on independant board.

All as per item No. 128 above but for One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

All as per item No. 128 above but for One 3 point 5 Amps switch socket combination point controlled by one switch on the independent board.

Supply and fixing of Switch piano , single pole one way, flush type 5 Amps capacity 230 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of socket outlet 2 in 1 multipurpose 2/3 pin 5 amps flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing switch socket combination 2 in 1 multipurpose 2/3pin 5 amps flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing switch socket combination 2 in 1 multipurpose 3pin 5/15 amps flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed .

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

Supply and fixing LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fix LED energy efficient building security light fitting of capacity of 35 W for fixing in GI pipe bracket on wall complete all as specified and directed by Engineer-in-Charge. NOTE : GI bracket, clamp, nut and bolt etc will be measured in separate item.

Supply & fixing galvanised iron tube bracket of suitable size dia light grade and 1.2 mtr length for fixing building security light, with all fixing arrangement including necesssary clamp, nut and bolt etc. as required size complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Exhaust fan, heavy duty, 225/230 mm sweep metal body with louvers, AC single phase, 230 Volts, 1400 rpm and connecting up with and including necessary 3 core PVC insulated copper flexible cord of size 23/0.019 from exhaust fan to the ceiling rose including making hole in the wall and making good edges in cement plaster complete all as specified and directed.

Supply and replace MCB double door DB SPN 4 way with 200 Amps busbar including removing the existing unserviceable one and making good the distrubed surface to match with the existing surface complete all as specified and directed by Engineer-in-Charge.

Supply and replace MCB double door DB SPN 8 way with 200 Amps busbar including removing the existing unserviceable one and making good the distrubed surface to match with the existing surface complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair MCB SPN 40 Amps 240 volts for fixing on MCB DB complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair MCB SP 6 to 40 Amps 240 volts for fixing on MCB DB complete all as specified and directed by Engineer-in-Charge.

M & L Submain wiring on surface with 2 runs of single core 6 sqmm PVC insulated unsheathed multistranded 1100 volts grade with copper conductor drawn through and including non-metalic rigid PVC conduit and conduit accessories of medium grade not not less than 25 mm dia including one run of single core 6 sqmm PVC insulated unsheathed multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing all as specified and as directed.Note:-Two runs of cable, one run of earth contuinity conductor and one run of conduit shall be measured as one unit length. Note: For the concealed wiring made concealed, cutting and chasing will be measured and paid seperately.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground to a depth not less than 2.25 m below ground level with top edge of earth plate not less than 1.5 m below normal ground level connected to GI earth wire 4 mm dia drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, checknuts and washers all as shown in Electrical Plate No.3 of SSR Part-I and connected to main switch board including excavation and earth work, PCC chamber in 1:3:6, RCC Cover in 1:2:4 type B-1 reinforced with 8 mm dia MS bars at 10 cm c/c, 20 mm dia medium grade GI pipe with funnel and wire mesh complete and watering arrangement complete all as specified and directed by Engineer-in-Charge. (Note: GI pipe 15mm dia, GI wire 4mm dia upto 7.5m deemed to be included in quoted rate.)

Supply and lay on wall/in ground/on pole ISI marked XLPE insulated armoured, heavy duty, electric cable with aluminium conductors 1100 volts laid in trenches, floors, ducts, pipes drawn across the road/paths/drain/along poles/walls/floor/equivalent etc including jointing & testing complete all as specified of size 25 Sqmm , 2 core complete all as specified and directed by Engineer-in-Charge.

Supply, spread river sand of approval in cable trenches providing for cable cushioning as directed. NOTE :- Punned thickness of sand only will be measured and paid complete all as specified and directed by Engineer-in-Charge.

Cutting the existing GI Pipe of 25mm to 50mm bore for alterations or additions and screwing the tubing for inserting of new GI specials such as Tee/ Reducers/ Tail pieces/ Collers/ Sluice Valve/ Air release Valve etc complete all as specified and directed by Engineer-in-Charge.

Supply and lay PCC cable covers for LT cable protection, Class LV, Type 1 of size 250x150x40mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing medium grade GI tubing of 50 mm dia for XLPE cable protection complete all as specified and directed by Engineer-in-Charge.

RAM CHARAN CONSTRUCTIONS

SAI RUPA CONSTRUCTIONS