PROVN OF 04 X SENTRY POST FOR LAILAPUR AT CIJW SCHOOL AND CERTAIN B/R AND E/M WORKS FOR NFS NODE, LAILAPUR, VAIRENGTE MILITARY STATION UNDER GE SILCHAR

Amount

PART-I (B/R WORKS) Surface dressing not exceeding 15 cm deep and getting out soft/ loose soil complete all as specified.

Excavating in post holes (or similar holes) each not exceeding 0.50 cum, getting out hard and dense soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance not exceeding 50 mtr complete all as specified.

Excavating in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and not exceeding 1.5 mtr in depth and getting out soft/loose soil complete all as specified.

Returning, filling in, trenches including Spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick all as specified.

Removing of surplus soil to a distance not exceeding 50 metre and deposited where directed at a level not exceeding 1.50 metre above the starting point all as specified.

Material and labour for brick work with subclass 'B' old size bricks, straight or curved on plan exc 6m mean radious , built in cement mortar 1:4 all as specified.

Material and labour for Hardcore of broken boulder or stone gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified.

Material and labour for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregates as in foundations, filling and mass concrete all as specified.

Material and labour for 150 mm thick PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregates as in bases in floor all as specified.

Material and labour for PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregates as in bed block, coping, cills, steps, kneelers, bed plates, apex stones kerbs and similar works including weathering, slightly rounded or chamfered angles and throating and necessary formwork all as specified.

Material and labour for reinforced cement concrete, 1:1.5:3 type A1 using 20 mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns,etc. basement slabs, under-reamed piles and mass concrete etc complete all as specified. Note:- Reinforcement and form work shall be measured and paid separately.

Material and labour for reinforced cement concrete 1:1.5:3 type A1 using 20 mm graded crushed stone aggregates as in columns, pillars, etc complete all as specified. Note:- Reinforcement and form work shall be measured and paid separately.

Material and labour for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregates as in pavement/ hardstanding finished the surfaces even and rough complete all as specified.

Material and labour for use and waste of formwork to sides of rough finished flat concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

Material and labour for use and waste of formwork to sides of rough finished flat concrete formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified.

Supply and fix mild steel angle, flat iron for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified.

Supply and fix framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified.

Supply and fix mild steel screw bolts (machine made) of 12 mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,length of bolt exceeding 5 cm but not exceeding 10 cm complete all as specified.

Material and labour for Mild steel TMT bars of Fe 500D, 10 mm dia and over, cut to length, for chainlink fencing and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified.

Material and labour for Mild steel TMT bars of Fe 500D, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified.

Material and labour for Mild steel TMT bars of Fe 500D, 8 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified.

Supply and fix Chain link fencing 4 mm dia galvanised steel wire, 75 mm x 75 mm mesh, made up into mattresses or cages, lapped, wired and laid/fixed in position, including line wires, any mesh, any size, any type of standards rails straining bolts etc including provisioning of binding wires complete all as specified.

Supply and fix Galvanised. 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified.

Supply and fix Rotational moulded polyethylene water storage overhead tanks (cylindrical vertical with closed top) multi layered 500 ltr capacity hoisted and fixed in position including 20 mm dia Ball valves (Minimum weight of valve 210 gms) high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe complete all as specified.

Supply, lay and fix 15 mm bore galvanized iron water tubing medium grade including all fittings and fixed to walls and ceilings or laid in floors all as specified.

Supply, lay and fix 20 mm bore galvanized iron water tubing medium grade including all fittings and fixed to walls and ceilings or laid in floors all as specified.

Supply and fix 15 mm bore Bib taps, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified. Make Parryware Cat No G0304A1/ Jaquar Cat No FUS-29037/ Marc Cat No MCT-1030

Supply and fix 15 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

Supply and fix 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

Supply and fix 15 mm bore Stop valves, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 20 mm bore iron pipe or for unions and fixed complete all as specified. Make Jaquar Cat No FLR-5053N/ Parryware Cat No G3307A1/ Marc Cat No MCT-1060

Material and labour for preparation of new and previously untreated steel and iron surfaces of any description, not otherwise described exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide primer all as specified.

Material and labour for preparation of new and previously untreated steel and iron surfaces of any description, not otherwise described not exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide primer all as specified.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of primer complete all as specified.

Supply, lay and fix 40 mm bore galvanized iron water tubing medium grade including all fittings and fixed to walls and ceilings or laid in floors all as specified.

Supply, lay and fix 25 mm bore galvanized iron water tubing medium grade including all fittings and fixed to walls and ceilings or laid in floors all as specified.

Supply and fix 40 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

Supply and fix 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

Cutting existing steel tubing of 40 mm dia pipe and make a new connection by adding TEE, bend and all necessary fittings complete all as specified.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out soft/ loose soil complete all as specified.

Excavating in post holes (or similar holes) each not exceeding 0.50 cum, getting out soft and loose soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance not exceeding 50 mtr complete all as specified.

Material and labour for half brick thick work with sub class 'B' old size bricks built in cement mortar 1:4 straight or curved on plan to any radius complete all as specified.

Material and labour for reinforced cement concrete, 1:1.5:3 type A1 using 20 mm graded crushed stone aggregates as in beams, cantilevers, bressummers, lintels etc. complete all as specified. Note:- Reinforcement and form work shall be measured and paid separately.

Material and labour for reinforced cement concrete, 1:1.5:3 type A1 using 20 mm graded crushed stone aggregates as in slabs supported on walls,beams and columns in floors,roofs,landings,balconies, canopies, deck slabs and in shelves and the like complete all as specified. Note:- Reinforcement and form work shall be measured and paid separately.

Material and labour for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410 -W (Gde- E- 250) quality-B complete all as specified.

Supply and fix bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified.

Material and labour for use and waste of formwork to sides and soffits of rough finished flat surfaces of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.complete all as specified.

Material and labour for use and waste of formwork to edges of rough finished concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 5 cm but not exceeding 10 cm wide complete all as specified.

Material and labour for use and waste of formwork to soffits of rough finished flat suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) complete all as specified.

Material and labour for Mild steel TMT bars of Fe 500D,8 to 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified.

Material and labour for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick wall or concrete surfaces, finished the surfaces even and fair with using WPC as per manufacturer instruction complete all as specified. Note: WPC shall be measured and paid separately

Material and labour for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick wall or concrete surfaces, finished the surfaces even and smooth without using extra cement complete all as specified.

Material and labour for 10 mm thick rendering in cement mortar 1:3 on ceiling surfaces, finished the surfaces even and smooth without using extra cement complete all as specified.

Material and labour for loose filling with broken bricks of gauge 40 to 80 mm in soakage pits, soakage wells complete all as specified.

Material and labour for 25 mm thick cement concrete 1:2:4 type B0 using 12.50 mm graded crushed stone aggregates as in floor and finished the surfaces even and rough complete all as specified.

Material and labour for 75 mm thick PCC 1:3:6, type C2 using 40 mm graded crushed stone aggregates as in plinth protection and finished the surface even and smooth without using extra cement complete all as specified.

Material and labour for 7 to 8 mm thick mat finished colour ceramic tiles of size 300 mm x 300 mm as in floors set and jointed and pointed in white or colour cement to match and laid over 15 mm thick screed bed in cement mortar 1:4 complete all as specified.

Supply only Integral waterproofing compound.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including washers complete all as specified.

Supply and fix Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall or Eaves board, fixed with self tapping screws including washers complete all as specified.

Material and labour for for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600 mm x 600 mm with main runner 38 mm x 24 mm and wall angle 24 mm x 24 mm using 4 mm thick High Pressure steel Crude Everest Non Asbestos Fibre Cement plain Board (E-Board Classic) in a grid of GI system duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450 mm from the adjacent wall, Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610 mm c/c,so as to form 600 mm x 600 mm grid and painted with two coats of acrylic emulsion paint of approved shed /make over a coat of cement primer before installing it on the grid complete all as specified . Make: Everest/ Lafarge/ Armstrong

Material and labour for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified.

Material and labour for preparation of newly plastered wall surfaces and applying three coats of white wash complete all as specified.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of colour wash over a coat of white wash complete all as specified.

Material and labour for prepration new or previously untreated wood or wood base materials of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Excavating over areas, not exceeding 1.5 mtr deep and getting out soft/ loose soil complete all as specified.

Material and labour for 40 mm thick cement concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregates as in floor and finished the surfaces even and rough complete all as specified.

Material and labour for 25 mm thick prepolish chequered cement concrete tiles and area of each tile shall be 30 cm x 30 cm , set, jointed and pointed in neat cement slurry in floors with grey cement or colour pigment to match and laid over 15 mm thick screed bed in cement mortar 1:4 complete all as specified.

PART-II (E/M WORKS) Supply and fix anti static flooring (ESD flooring) PVC vinyl Mat with three layers and thickness not less than 02 mm, abrasiveness loss less than 0.02g/cm2, Bulk resistivity between 105-108 Ohm, Resistivity of bottom between 103-105 Ohm, Resistivity of surface layer is between 106-109 Ohm including copper foil, adhensive & revets as required and shall be installed after ensuring the surface is clean & dry as per the manufacturer's directions and under experts supervision. Colour of flooring shall be approved from Engr-in-Charge/GE. Make : PB Stat clean solution Pvt Ltd/Blue Sky System Pvt Ltd/SR Build Cone Tech/ any other equivalent make as approved by GE.

Material and labour for Sub main wiring with PVC insulated unsheathed two run of 10 Sq. mm single core multistand copper conductor cable (FRLSH), 1100 volt grade alongwith one run of 10 sqmm PVC insulated and unsheathed copper conductor cable (FRLSH) 1100 volt grade, connected to common earth dolly as earth continuity conductor, drawn through 25 mm PVC casing caping complete all as specified. Note:-(a)two runs of 10 sqmm cable,one run of 10 sqmm cable and one run of PVC casing caping will be measured as one unit (b) Cable requireds for connection to MCBs/DBs shall be deemed to be included in the unit rate.

Material and labour for Sub main wiring with PVC insulated unsheathed two run of 6 Sq. mm single core multistand copper conductor cable (FRLSH), 1100 volt grade alongwith one run of 6 sqmm PVC insulated and unsheathed copper conductor cable (FRLSH) 1100 volt grade, connected to common earth dolly as earth continuity conductor, drawn through 25 mm PVC casing caping complete all as specified. Note:-(a)two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC casing caping will be measured as one unit (b) Cable requireds for connection to MCBs/DBs shall be deemed to be included in the unit rate.

Supply and fix 36 W LED edgelit luminaire of 600 mm x 600 mm size suitable for armstrong/grid ceiling complete for low ceiling applications including necessary fixing arrrangements and cutting false ceiling if any. Make:-Havells Item Description ENDURASLIMPROPLUS2X2PLR36WLED840MOD/ Bajaj Cat No BARSQL 36W WH/ Crompton Cat No LCPL-36-CDL(2X2)

Supply and fix 30W Energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP65 protection and Impact resistance of IK07 with 10KV built in Surge Protection Device including brackets and all fixing arrangements. Make:-Havells Item Description ENDURACITYLITEPLATPLUSSL30WLED757SASYBOPC/ Bajaj Cat No BRLEP 30W LED WH/ Crompton Cat No LSTS-30-CDL

Supply and install 2 ton capacity 5 star rating inverter split type AC (indoor and outdoor including) of full load capacity 6400W, full load power 1665W, copper condensing coil and copper connecting pipe of length 3.50 mtr moisture removal 2.2ltr/hour, dual rotor compressor with remote control and 10 years warranty including two pin metal plug and socket with single pole MCB of 20A 'C' series for connection the AC. Make of AC:- Bluestar/Hitachi/Daikin/Lloyd Make of MCB:-Legrand/Schneider/ABB/ Siemens

Supply, installation, commissioning and testing of water cooler with built in purifier partially stainless steel, electric driven single phase having approx storage capacity 40 litres and cooling capacity 40 litres complete all as specified and directed. Make- Usha/Voltas/Blue Star

Material and labour for earthing with galvanised steel earth plate electrode 60cmX60cmX 6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 32 mm x 6 mm thick GI strip protected by 40 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR part-I all as specified.

Material and labour for air termination, single pointed, copper rod 12 mm dia and 300 mm long complete all as specified.

Material and labour for test point terminal block made of gun metal or phosphorus bronze size 75 mm x 75 mm x 25mm drilled and screwed including 3 nos. 8 mm dia 25 mm long hexagonal head screw complete all as specified.

Material and labour for copper strip 20 mm x 3.15 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified.

Material and labour for Copper strip 32 mm x 6 mm buried in ground complete all as specified.

Material and labour for point wiring with 1.5 Sqmm PVC insulated un sheatned multi stranded copper conductor cable (FRLSH) 1100 volts grade two single core conforming to IS-694-1990 and one run of continious earth wire with 1.50 Sqmm PVC insulated unsheatned stranded copper conductor cable (FRLSH) draw in and including heavy duty PVC conduit (ISI marked) in concealed with all necessary fittings and fixures with GI sunken boxes with earth dolly and 3mm laminated cover sheet suitable for fixing switch, socket, regulator including making good disturbed surface with CM (1:4) to match with the existing surface complete all as specified for the following :- Note:- Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

(a) One light point/ fan point/ exhaust fan point controlled by one, one way switch 5 Amps

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

(c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

Material and labour for Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal complete all as specified.

Supply and fix switch piano flush type button single pole one way 5 Amps with cover plate all as specified and directed.

Supply and fix ceiling rose surface bakelite with three terminals all as specified and directed

Supply and fix wall mounted high speed fan with three strong blades plastic body 400 mm sweep 2200 rpm 100W power and 100 cmm air delivery. Make :- Usha/Havells/Bajaj

Supply and fix 20W surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver with 3 core flexible copper cable PVC insulated of size 16/0.20 mm etc. Make: Havells/ Bajaj/ Wipro/Eveready

Supply and fix 10W LED lamp with Angular holder insulated body with back plate suitable for batten fittings including 3 core flexible copper cable of required length. Make of LED:- Havells/Crompton/Bajaj/ Eveready

Supply and fix 10W ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs. Make:- Havells Item Description RUGBYNEONFT10WLED860SSYMTOPC/ Bajaj Cat No BIBWP 10W LED/ Crompton Cat No LBHE-10-CDL

Supply and fix 70W LED search light for long range vision with IP 65 protection included connection with suitable services wire of three core copper conductor, PVC unsheathed armoured cable including fabrication of steel structure for mounting and fixing of search light including grouting of angle iron frame wall/ floor made up angle iron/ MS flat square tubing etc and bearing, welding, drilling and assembling and suitable for rotation in 180 degree. Make: Bajaj/ Philips/ Crompton

Supply and fix sheet metal enclosure MCB DB SPN with 200 Amp rated bus bar 4 way 415 V (double door type) with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc. and making good of disturbed surface to match with existing colour of wall complete all as specified.. Note: Quoted rates shall be deemed for brick wall / concrete wall cutting and making good as per existing surfaces.

Material and labour for earthing with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 mtr below gound level) with top edge of the plate not less than 1.5 mtr below gound level connected to earth lead wire 4mm dia protected by 15 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcol and common salt in alternate layers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover 10mm thick hinged to CI frame and 6mm MS rod for handle, necessay excavation and earth work in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 SSR part-1 all as specified.

Supply and lay Cable or fixed to wall/floors XLPE insulated,PVC bedded, Galvanised steel strip or wire armoured,Electric power cable heavy duty with stranded alluminium conductors,1100 volt grade, 10 Sq mm, 2.00 Core all as specified.

Supply and spread sand in trenches as sand cushioning to under ground cable for protection with fine river sand(dry) and provide reqd cover after punning down complete all as specified and directed. Note : thickness of sand cushion after punning down will be measured and paid.

Material and labour for sub-class 'B' old size brick laid in trenches for cable protection all as specified.

Material and labour GI tube light grade 40 mm for protection of UG cable including dismantling complete all as specified and directed. Including dismantling of old unsv pipe.

M/S Manik Lal Gupta

M/S RAJU ENTERPRISES AND BROS

M/S. N.A.BARBHUIYA

Younus Khan