Repair work for Gandhi park Mulligirampattu Main road Anganvadi center in Nellikuppam Municipality

Supplying and filling with clean M. sand in layers of not more than 15cm thick well rammed watered and compacted including cost and conveyance of sand and filling charges etc complete as per SS 7 & 24 – V, VI ( S4) 8

Plain cement concrete of mix 1 : 4 : 8 ( one cement , four sand and Eight aggregates ) using 40 mm ISS HBG metal for foundation and flooring, including , dewatering, if found necessary, and laid in layers of not more than 15 cm thick, well rammed and consolidated, including cost and conveyance of all materials and labour charges for mixing, laying, compacting and curing etc. completed as per standard specification and as directed by departmental officials

Centering the soffits of Drain sides plain surface including using steel sheet with mild steel angle of size 25mm x 25mm x 3mm laid over deer joined of size 10mm x 6.5cm spacing about 90cm c/c and supported by casurina pole of 10cm to 13cm dia spacing 75cm c/c etc. including cost and conveyance charges etc. complete as per standard specification.

Reinforced Cement concrete 1:1.5 :3 (one cement, one and half M.sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete and also including fixing fan clamps and fixtures in rcc works wherever necessary as directed by departmental officer etc., complete.

Supplying , fabricating and placing in position of steel Reinforcement using Mild steel or Ribbed Tor Steel rods, for all RCC works as per the design given by the departmental officers including cost of steel and binding wire and all labour charges for cutting, bending, tying and placing in position etc. complete as per standard specification1.

Brick work in CM 1:5 (one cement & five sand) using III class country bricks of size 8 3/4"X4 1/4" X 2 3/4" including finishing, curing, etc., complete complying with standard specification - 100CFT

Painting two coats for Interior surface with approved Interior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Manufacturing supplying and fixing of MILD STEEL DOOR made out of 50 x 50 x 6 mm M.S angle for outer frame,35 X 35 X 5mm M.S.Angle for outer frame of shutter. The entire shutter area shall be covered with CRC sheets (18 G) with 5Nos, of stiffners using M.S.Flats of size 25 X 6mm at equal intervals horizontally. The corners of the frames and shutter with CRC sheets shall be welded by adopting flash butt welding or any other suitable method. Provision towards 3Nos, of Hinges incase of single shutters / 6Nos,of Hinges incase of Double shutters of 125 X 31 X 1.25mm size placed at appropriate intervals and provisions shall be made for Tower bolts 2Nos, Aldrop 1No. The frame shall be provided with 6Nos,of Hold fast of 200mm length using 50 X 6mm M.S.Flat. The entire frame and shutter shall be provided with one coat of red oxide primer including cost of hold fasts,hinges, locking arrangements, handles wind appliences etc., complete and as directed by the departemental officers.

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixedin position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x30mm. The over all sizeofframes shall be 50mm x 45mm with suitable rabate for shutter

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Wiringwith2x1.5sq.mm.PVCinsulatedSCunsheathedFRLScopperconductorof1100VgradeinsuitablePVCrigidpipeconcealedinwallandceilingwithPVCaccessoiresinflushithwallwith3mmthickhylumsheetcoverwithTWswitchboxand5AFTswitchandmakinggoodoftheconcealedportionwithsuitablecolourforPVCconcealdlight/fan Point (for electronic regulator) (5 points per coil) SD 25

Wiringwith2x1.5sq.mm.PVCinsulatedsinglecoreunsheathedFRLScopperconductorcableof1100VgradeinsuitableheavygaugeMSconduitpipeonwallandceilingwithMSaccesorieswithMSswitchBoxand5AFTswitchwithpaintingofsuitablecolourcontinuousearthwireconnectionof1.5sq.mmcopperwireforlightpoint/fanpoint(for electronic regulator) SD 12

Wiringwith2x4sq.mm.PVCinsulatedSCunsheathedFRLScopperconductorcableof1100VgradeinsuitablePVCrigidpipeconcealedinwallandceilingwithPVCaccessoriesinlushwithwallwith150mmx100mmx113mmTWswitchboxwith3mmthickhylemsheetfor15A3pinnoninterlockingwallsocketwith15Aflushtypeswitchwithontinuousearthwireconnectionof4sq.mmcopperwireandmakinggoodoftheconcealedportionwithsuitablecolour for concealed power plug point ( SD 40 )

1 HP Motor

Sintex Tank

Goods and Service Tax @ 18%

Please Enable Macros to View BoQ information