ADDN ALTN TO EQPT AND SECURITY PASS

Amount

M & L for complete removal of existing roof treatment (Mud puska, Cement Tiles or Old APP Roof treatment etc) including bedding layer in cement mortar/Mud and disposed from MoD land complete all as specified and directed by Engineer-in-charge.

M&L PCC 1:2:4 type B1 using 20mm graded aggregate mixed with liquid water proofing compound laid as per manufacturer instructions 25 mm thickness as in padding over roof slabs for providing proper slope to the concrete padding, surface finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge. Note : WPC shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and directed by Engineer-in-Charge.

M&L for five layer prefabricated atactic polypropylene polymer (APP) modified 3 mm thick membrane ( weight not less 3 kg/sqm) reinforced with 160 gms polestar non-woven fabric with scratched tool before finishing roof surface. When the concrete surface is still green, 10 mm thick 1:4 cement plaster shall be laid the roof surface shall be thoroughly wire brushed washed dried up and cleaned of all foreign matter and dust prior to the application of primer on the dried surface one coat of approved bituminous primer, having density in the range of 0.87 to 0.89 / kg at 25 degree and viscosity of 70 to 160 CPS manufactured by the same manufacturer @ 0.40 litres/sqm shall be applied. APP membrane shall be laid on primed surface tourch application method after allowing 24 hours of primer to dry. Laying of APP membrane shall be commenced at the lowest level and worked upto the crest.APP membrane will normally be laid in length at right angle to the direction of slope. The overlaps shall be of minimum 100 mm on longitudinal direction and 150mm on the transverse direction. All overlaps shall be bonded with bitumen primer and levelled by the heating the overlaps with brutane tourch. This treatment shall be done by the approved authorised applicator. Guarantee of treatment shall be for 10 years. Thereafter APP membrane shall be painting with two coat of water proofing paint with aluminium finish. (ii) Independent testing of membrane for the approval technical parameters specified hereinafter shall be carried out the approved laboratories like National test house any other Govt approved laboratory having facilities for the testing of membrane.

M&L for two coat of water proof aluminium paint incl preparation of newly or previously untreated surfaces of any description, over 10cm width or girth, not otherwise described complete all as specified and directed by Engineer-in-charge

Dismantling loose concrete cover of RCC columns, beams, slabs chajjas and the like as directed, roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry, incl derusting of steel reinforcement, providing fabric mild steel wire mesh 75 mm x 75 mm x 2 mm dia as reinforcement to concrete. After placing the additional reinforcement all concrete surfaces shall thoroughly scrubbed with brushes, washed with water and alloy to dry . To this surfaces apply chemical polycrete admixture at the rate not less than 2% by weight of cement and providing minimum 30 mm thick (average thickness ) gunniting mix (using 1 part of ordinary Portland cement 53 Grade and 2 parts of ghaggar sand mixed with adhesive / admixture at the rate as directed) with a pressure of 2 to 2.5 Kg per Sq cm by gunniting machine and surfaces finished even and fair, incl necessary padding, shuttering / form work . Including 5 mm thick cement plaster in CM (1: 4 ) complete all as specified and directed by Engineer - in -charge. Note:- (a) The rate is inclusive for scaffolding or reqd necessary arrangement for multi-storey bldg external gunniting.

Taking down cement plaster of any description on brick or concrete surfaces of walls or ceiling etc incl. Raking out joints , hacking for key and scrubbing down with water complete all as specified and directed by Engineer-in-Charge.

M&L for 15 mm thick cement plaster in cement mortar 1:4 on concrete or brick surface and finished even and smooth w/o using extra cement all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces (Cement plaster 1:6) finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge

M&L for complete removing existing treatment old surface of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance 1st quality exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including change of existing colour if required complete all as specified and as directed by Engineer-in-Charge. Note:- (a) The rate is inclusive for scaffolding or reqd necessary arrangement for multi-storey bldg painting.

M&L for complete removing existing treatment old surface of wall and applying two coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer by EIC, of required shade and colour over applying plaster of paris putty of 2 mm thickness over surface to prepare the surface even and smooth. complete, as per manufacturer's specification. complete all as specified and as directed by Engineer-in-Charge.

S & F in repair 'E' board(Design: LACK & hill) : 605x605x4 mm thick, white pre laminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanized iron imposed grid with 24 mm wide T-section exposed flanges which shall be power coated white. The frame work shall be comprise of main runner made from 0.33 mm thick galvanised steel sheet and of size 24 mm X32mmX300 mm board spaced at 120 mm maximum center to center, hangers of GI wire4 mm dia to be fixed by approved rawal plug level and fasteners and screws etc. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall , flushing fitting of 1200 mm longer cross tee(with double stitching) to be interlocked between main runners at 600 mm center to center from 1200X600 mm modules cross tee longer than 600 mm to be supported independently . 600mm long cross tee centrally between the 1200 mm cross tee(with double stitching) to be interlocked between main runners at 600 mm center to center from 1200X600 mm modules cross Tee longer than 600 mm to be supported independently . The perimeter wall angle shall be 0.45 mm thick GS sheet of size 19 mm X 19 mm and 300 mm long of white colour all as per manufacturer's instructions complete all as specified and directed by Engr-In-Charge.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) exc 1.5 Sqm but n exc 4 Sqm each,incl removing complete all as specified and directed by Engr-In-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners not paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F for butt hinges of stainless steel 100mm size complete all as specified and directed by Engr-In-Charge.

S&F for Brass Mortice lock, vertical type, size 100mm 4 levers vertical with fancy handle (as decided by EIC) complete all as specified and directed by Engineer-in-Charge.

S&F for 150 mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-In-Charge.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 7mm/450 x 350 x 7mm thick over and including 10 mm thick rendering in cement mortar 1:4 as in backing coat for tiles on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-In-Charge.

M&L for Vitrified ceramic coloured (dark/light shade) tiles (600x600)x9/10mm thick in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in cement mortor 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Vitrified ceramic coloured (dark/light shade) (600x600)x9/10mm thick in skirting etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick plastering in CM 1:4 as in backing coat of tiles all as specified and directed by Engineer-in-Charge.

S & F in repair Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all omplete as per architectural drawings and the all as specified and directed by Engineer-in-Charge.

Supply and fixing 5.5 mm thick ordinary quality sheet glass exe 0.5 sqm in each pane of glazing with oil putty /beading etc all as specified and directed by Engineer-in-Charge.

supply and fixing of 5mm thick PVDF coating Aluminium composite panel complete in all respect of Indo bond or equivalent make as per approval of GE. complete, all as specified and directed by Engineer-in-Charge.

S&F in repair 110 mm bore PVC (SWR ) pipe single socketed in any length with rubber ring joints, laid in trenches or in floors etc including removing from site complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC (SWR) bends any radius 110mm bore pipe incl taking down complete all as specifed and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for.complete all as specified and directed by Engr-In-Charge.

M & L for 75mm thick PCC 1:3:6 type C-2 (40mm graded stone aggregate) as in plinth protection complete as directed by Engr-in-Charge.

Dismantling of ceiling board /Wall panelling/ RCC Jalli of any thickness and of any description including cover fillets/battens complete all as specified and directed.

M & L for brick work with sub-class `B' bricks old size, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:4 complete all as specified and directed.

S&F for powder coated (minimum thickness of powder coating 50 micron) aluminum anodized three track sliding window and ventilators with two or more shutter with 5 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing ,handle lock,etc rubber beading and glazing clips etc using following sections as given in 'JINDAL' catalogue etc as specified as per manufacturer instructions with the following size and directed by Engineer-in-Charge. Note : (a) Rate included sliding window section, Glass and Wire mesh. (b) Opening will be measured for payment purpose excluding aluminum frame.

S & F anodized aluminum door shutters of any type , aluminum section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminium snap beading screws etc. complete all as specified

M&L prelaminated particle board 12mm thick interior grade prelaminated both side with decorative choice lamination and other side balancing white lamination with screws to timber frame work

S&F Aluminium grills 10 mm thick along with stainless steel wire mesh as complete, all as specified and directed by Engineer-in-Charge.

Surface excavation n.exc (not exceeding) 30 cmdeep and averaging 15cm deep and getting out in hard dence soil complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate ) as in sub base for flooring finishes complete all as specified and directed by Engr-in-Charge.

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for 60mm thick, M-30 Grade Machine pressed precast concrete interlocking paver block any shape and size casted in plastic moulds and compacted on vibratory table confirming to IS 15658-2006 with grey cement and pigment complete all as specified and directed.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) not exc 1.5 Sqm each , incl removing.

S&F factory made Solid PVC Door Frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification complete all as specified and as directed by the Engineer-in-Charge.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rail with suitable PVC sheet beading, & joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tank and removing to store exceeding 500 but n.exc 1000 ltrs complete all as specified and directed.

S&F for rotational moulded polyethylene water storage tanks triple layers (white colour) of 1000 ltrs capacity (cylindrical vertical with closed threaded top) hoisted and fixed in position including 20mm dia HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves, bore dia of pipe 20mmwith iron wheel head, screwed both ends for iron pipe and fixed

Taking up or down 15mm bore steel tubing and connections, including cleaning for re- fixing or removal to store complete all as spd and directed by Engr-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for re- fixing or removal to store complete all as spd and directed by Engr-in-Charge.

S&F 15mm bore steel water tubing medium grade , galvanized ISI marked with all fittings fixed to wall & ceiling or laid in floors complete all as spd and directed by Engr-in-charge.

S&F 20mm bore steel water tubing medium grade , galvanized ISI marked with all fittings fixed to wall & ceiling or laid in floors complete all as spd and directed by Engr-in-charge.

M&L for Non skid ceramic coloured tiles (300x300/400x400)x7 mm thick in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in cement mortar 1:6 complete all as specified and directed by Engr-In-Charge.

M&L for PCC 1:2:4 type B-0 (Using 12.5 mm graded stone aggregates) of 25 mm thick as in levelling course ,finished surfaces even and rough to receive floor finish complete all as specified and directed.

S&F in repair CP bib taps long body , cast copper alloy, fancy type with crutch or butterfly handles, chromium plated, screwed down to iron pipes or for brass ferrule of 15 mm bore complete all as specified and directed.

S&F in repair CP angle or plain stop valves, cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed.

S&F in repair 15 mm pillar taps swan neck cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered "Hot" or Cold with long screwed shanks and fly nuts screwed for iron pipes and fixed , fancy type complete all as specified and directed.

S&F in repair brass chromium plated waste coupling 32mm bore WHB complete all as specified and as directed.

S&F in repair 15mm dia PVC Connection 600 mm long with brass nuts complete all as specified and as directed.

S&F in repair 10 litre PVC valve less symphonic action type Low level flushing cistern with inlet ball valve float and handle incl CI bracket and 32mm bore PVC flush pipe and connection to pipe complete all as specified and as directed.

S&F in repair vitreous china squatting pan “orrisa” pattern of size 580mmx440mm “white” with integral foot rest (excluding flushing cistern and flush pipe) incl provision of cement concrete bedding, CI ‘P’ trap 100mm dia connection to trap and flushing pipe, anti-syphonage complete all as specified and directed by Engineer-in-charge.

S&F in repairs vitreous china wash hand basin of size 550 mm x 400 mm white, flat back incl angle iron brackets incl waste pipe of 32 mm dia of suitable length, pvc connection of 15 mm dia & 450 mm long with PTMT nuts with 32 mm dia brass chromium plated bottle trap and waste coupling complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs stainless steel chromium plated grating (round) 125/150mm dia fixed over floor/nahani trap (with hole and without hole) complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 110 mm bore PVC (SWR ) pipe single socketed in any length with rubber ring joints, laid in trenches or in floors etc including removing from site complete all as specified and directed by Engr - in- charge.

M&L for 16-18mm thick Granite slab on top of cooking platform, bar counter, shelves and similar work including cutting polishing rounding on edge etc machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed by Engr-In-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid,bedded and pointed in any mortar complete all as specified and directed by Engr-In-Charge.

M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete including 20 mm screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surface and applying two coats of distemper oil emulsion on walls over a coat of primer incl 3mm thick wall care putty on walls complete all as specified and directed by Engr-In-Charge.

M&L for prepration of old plastered or unplastered surfaces of walls and applying two coat of approved shade of oil emulsion distemper with 3mm thick elastomeric wall care putty on walls, including repairing of pot holes and cracks with putty, take it plastered where required complete all as specified and directed by Engr-in-Charge.

S&F in repair aluminium deco grills confirming to DG-104 grade all as specified and directed by Engr-In-Charge.

S&F 150mm long aluminium handle cast type polished bright complete and specified and directed by engr-in -charge.

S & F in repair aluminium extruded section door closer hydraulically operated designation No-03, universal type, suitable for door shutters of 851 to 1000mm width and of weight of 61 to 80 Kg complete all as s&d by Engr In Charge.

S & F in repair 140mm long floor door stopper of Almn alloy body and tongue with hard drawn steel spring complete all as specified and directed by Engr In Charge.

M&L Glazed ceramic coloured tiles in vertical surface 300X 450X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl back plaster 10 mm thick in cm 1:4 & including 100mm thik cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base for floors finishes complete all as specified and directed by Engr In Charge.

M&L Virified Ceramic light shade tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.72 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match flooring( in any pattern) and jointed with neat cement slurry over 15 mm thick cement screed in CM 1:6 and pointed with coloured cement matching with surfaces of tiles as in floor complete all as specified and as directed by Engr-In-Charge.

All as per item No 74 above but as on vertical surface of wall such as skirting/dado including 10mm thick cement plaster (1:4) as in backing coat of tiles complete all as specified and as directed

M &L for PVC profile for wall panelling colour / shade as approved size 250mm wide, 08 mm over all thick with 1 mm wall thickness fixed with screw to mild steel square ( size 20mmx 20mmx 1mm thick) tubler frame work including one coat of red oxide primer, fixed to walls and including dismentling complete all as s&d by Engr-in-Charge.

M&L for PVC profile corner beading L/T type for wall panelling, colour/shade matching with wall panelling complete all as specified and as directed

Material and labour for false ceilings using GI snap grid system with roll-formed out of hot dip galvanised steel caping (powder coated) main runner 38 x 24 mm , cross Tee 29 x 24 mm and wall angle 24 x 24 mm members suspended with 4mm dia GI wire, carry maximum load up to 8.10 Kg/Sqm with 4mm thick designer ceiling board , pre painted Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions size 595 x 595mmx 4mm thick any texture (Lake and Hill, oceaniccascade or Electra) as approved by GE all as per , Everest Ceiling grid system 'Regular T-2430' or its equivalent make of "'Ramco, Charminar/Armstrong'' at any height including dismantling complete all as specified and as directed by Engr-In-Charge.

Supply and fix metal clad socket single pole and neutral sheet metal enclosure with and 20A earth plug and socket compete with one single pole MCB 20A 240 Volts all as specified and directed by Eng-in-Charge.

M & L for submain wiring with two run of 4.0 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 4.0 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductordrawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified - 2 Runs of 4.0 Sqmm single core and one run of 4.0 sqmm single core cable.

M & L for submain wiring with two run of 6.0 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 6.0 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductordrawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified - 2 Runs of 6.0 Sqmm single core and one run of 6.0 sqmm single core cable.

M & L for submain wiring with two run of 10.0 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 10.0 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductordrawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified - 2 Runs of 10.0 Sqmm single core and one run of 10.0 sqmm single core cable.

Supply, lay and connect XLPE insulated, armoured heavy duty electric cable having 50 sqmm cable size cross sectional area with aluminium conductor, 650/1100V Grade, confirming to IS 7098(Part 1) 1988, in trenches/ducts/poles /pipes/walls etc. complete all as specified and as directed by Engineer-in-charge.

Supply and fixing sheet metal enclosure with double door category of protection type IP-42 factory made with tinned copper 200 Amps rated bus bar suitable for MCCB 4 Ways 415 Volts, concealed in wall such that front cover shall be seen flush with the wall surface all as specified and directed.

Supply and fixing MCCB 16 KA breaking capacity, three pole, 415 volts,100 amps C Curve capacity.

Supply and fixing sheet metal enclosure with double door category of protection type IP-42 factory made with tinned rated bus bar suitable for MCB SPN 8 Ways 240 Volts, concealed in wall such that front cover shall be seen flush with the wall surface all as specified and directed.

Supply and fixing MCBs 10 KA breaking capacity, single pole, 240 volts,5-32 amps C Curve capacity.

Supply and fixing MCBs 10 KA breaking capacity, single pole and neutral 240 volts,40-63 amps C Curve capacity.

Taking down carefully copper/aluminium point wiring light ,fan, light fittings,socket or power) complete, such as switches, ceiling roses, pendents, regulators, sockets etc.removing materials to store for keeping in safe costudy or for taking credit (credit for above items should be made as per conditioned separately) and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with single core of FRLS PVC insulated unsheathed ISI marked 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm drawing through in and including PVC conduit size of not less than 20mm including conduit fittings and acessories concealed in wall / ceiling or surface conduit wiring on ceiling /wall terminated in flush metal box alongwith outer cover plate for mounting modular switch, socket and electronic regulator along with provn of earth wire of PVC insulated, unseathed, 1100 V grade cable multi stranded FRLS ISI marked copper conductor of size 1.5 Sq mm cable for Independent bd one 3 pin 15 Amps socket outlet including S/C 1.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR LS cable for continuous earth wire connected to gang box of required size for one light/fan/bell point controlled by one switch.

All as per item No 91 above but for one 3 pin 5 amps socket outlet on indipendent board with other switchs.

All as per item No 91 above but for one 3 pin 5 amps socket outlet on the same board with other switchs.

All as per item No 91 above but with 2.5 Sq mm cable for Independent bd one 3 pin 15 Amps socket outlet including single core 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR LS cable for continuous earth wire connected to gang box of required size.

S&F switch piano, flush type single pole, one way, 5 Amps, 240 volts all as specified and directed at site.

S&F switch piano, flush type single pole, one way, 15 Amps, 240 volts all as specified and directed at site.

S&F socket outlet 5 pin 5 Amps all as specified and directed at site.

S&F socket 16 Amps, 2 in 1, flush type all as specified and directed at site.

Supply and fixing ceiling roses, surface bakelite 65x50mm ,3 terminals 3 phase, PVC/Polycarbonate, isolated body all as specified and directed at site.

S&F of LED ceiling light 34 watt 2x2 recess LED, 6000 K luminaire having glare free symmetrical illumination Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver ,20 watt LED fitting with 100 lumen/watt, 6000K , 230 Volts, diffused optics ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, and testing complete all as specified and directed by the Engineer- In- Charge.

Supply and fixing in repair MCBs 10 KA breaking capacity, single pole, 240 volts, 6 to 40 amps C Curve capacity.

Supply and fixing in repair MCB SPN 40 Amp , 230 volt, 10 KA all as specified and directed by engineer-in-charge.

Supply and fixing in replacement MCB distribution board with Bus bar 200A neutral link , earth bar made out of CRCA mild steel sheet surface mounting SPN 8 way 230 volts double door type regal gray horizontal type Cat Part No - DHDPSHODRW08 or equivalent complete all as specified and as directed by Engineer-in-Charge.

Taking down fan, sealing cable end dismantling blades and removing fan and, blades to store complete all as specified and as sirected.

Hanging only ceiling fan (M.D.supply) and connecting up including provision of cable from ceiling rose or connector to fan®

supply and fixing wall mounted fan 400 mm 3 blade complete all as specified and as directed

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 450 mm complete all as specified and as directed.

Supply and install hi wall split units indoor/outdoor capacity of 2.0 Ton, complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 4.51 of capacity 2.0 Ton fitted on wall and out door to be fixing on roof/wall at requirement place including all necessary elecrical connections, bolting , nuts , clamping of 3 core copper cable, cooling tube , drain water pipe etc all as specified and directed by Engineer -in -Charge.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 90 V to 300 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5.0 KVA including fixing on wall and necessary electrical connections all as specified and directed by Engr-In-Charge.

Supply & Fix single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB 20-32 amps complete fixing on wall all as specified and directed by Engineer-in-charge

M&L cross arms bracings suppots clamps and back plates fabricated from structural steel sections including nuts bolts washers welding bending cold or hold drilled holes for bolts in any shape or size as indicated or directed and inclusive of one primer coat one under and one finished coat of paint for installation of condesning unit on the wall / ground complete all as specified and as directed by Engineer-in-charge

M&L laying of copper tubing of dia 5/8" including insulation and brazing work complete all as specified and as directed by Engineer-in-charge.

M&L laying of copper tubing of dia 1/4" including insulation and brazing work complete all as specified and as directed by Engineer-in-charge.

Suplly, & Fixing of 3 core flexible copper cable of size 2.5 Sq mm 1100 V grade complete fixing on wall by clamping/securing including connections all as specified and as directed by Engineer-in-charge

Rishi Constructions

deepankar trading co.