PROVISION OF SHED AT 105 HU 27 SQN AND STN HQ GUARD REST ROOM AT 11 END SUBSTATION ADDN/ALTN OF SAFETY BAY SPECIAL REPAIR TO ROOF OF AFDC BUILDING AND MINOR WORKS AT TECHNICAL AREA AT AF STATION GORAKHPUR

Amount

Demolition of cement concrete un-reinforced of any description and in any position not otherwise specially provided for complete all as specified and as directed.

M&L for PCC type D-2 1:4:8 using 40 mm graded aggregate as in foundation filling, sub base and mass concrete complete all as specified and directed.

S&F rolled mild steel work in tubular trusses including vertical member, rafter and purline including special shaped washer etc using ERW or induction butt welded tubes conforming to IS 1161-1979 graded ST-240 including cutting to dead length, notching, drilling riveting and/or welding & connecting with nuts & bolts complete all as specified.

S&F transparent colour FRP (Fibre Reinforced Plastic) sheet (corrugated, semi corrugated and plain) 3mm thick as in roof covering fixed with self driving machine made screws and washer and fitting as per manufacturer instruction of approved profile, shape and colour complete all as specified and directed.

M&L for preparation of previously untreated steel and iron surfaces of any description not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Surface excavation n.exc. 30 centimeter deep and averaging 15 centimeter deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide & not exceeding 1.5 metre depth for foundation etc and getting out, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc. 25 cm in soft/loose soil complete all as specified and directed

Removing excavated material to a distance n.exc. 50 mtrs and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for RCC 1:1½:3 type A-1 using 20mm graded stone aggregate as in foundations, footings, foundation beams; plinth beams; bases for columns, and mass concrete complete all as specified and directed.

M&L for RCC 1:1½: 3 type A-1 using 20mm graded mechanically crushed stone aggregate as in beam, lintel, cantilever complete all as specified and directed.

M&L for use and waste form work to sides of concrete foundation, footing, bases of columns and similar works in vertical or to batter of fair finished surfaces complete all as specified and directed.

M&L for use and waste form work to sides of concrete beam, side and soffits of plinth beam and similar works or to batter of fair finished surfaces complete all as specified and directed.

S&F mild steel TMT bar 10 mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for foundations, columns, beams and slabs hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S&F mild steel TMT bar 8 to 10 mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping for stirrups hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size straight or curved on plan exceeding 6 metre mean radius built in CM 1:4 complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:4 mixed with water proofing compound, finished even and smooth without using extra cement complete all as specified and as directed. Note:- Water proofing compound shall be measured and paid separately as supply only.

M&L for rendering 15mm thick in CM 1:6 on fair faces and of brick work or concrete surface finishing the surface even and smooth without extra cement complete all as specified and directed.

Supply only integral liquid water proofing compound complete all as specified and directed. Make: Dr Fixit Pidiproof LW+ or equivalent in specified make.

M&L for PCC 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregate as in benching, padding, coping etc including necessary form work complete all as specified and as directed.

M&L for hard core of broken stone or boulders of gauge n.exc 63 mm deposited spread and leveled in layers n.exc 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as sub base of floor complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as sub base of floor complete all as specified and as directed.

M&L for screed bed or bedding layer in CM 1:6, 15mm thick complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of wall or concrete surfaces in CM 1:4 finished rough for wall tiling complete all as specified and directed.

M&L for non skid ceramic coloured joint free tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for joint free glazed ceramic coloured tiles 350x250 x7/450x350x7mm thick for work on vertical surface such as skirting, dado, set & jointed in cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mt centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and directed.

M&L for PCC 1:3:6, type C-2, using 40 mm graded mechanically crushed stone aggregate as in surface channel and drains finished even and fair complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

S&F 2nd class hard wood (sal) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete as directed.

M&L for 35 mm thick IInd class hard wood plain framed, paneled shutter (two panel or more) with lock rails and panel of 9 mm thick B.W.P. commercial ply or 12mm veneered particle board with commercial veering on both faces. The size of rail and style as per I.S. 1003(Part-I) 2001 complete all as specified and directed.

S&F aluminum handle cast type anodized size 150 mm long, complete all as specified and directed.

S&F Aluminimum anolised barrel tower bolt of extroded section 200mm long, complete all as specified and directed.

S&F 100mm long type C-21, Butt hinges, extruded aluminum alloy with galvanized mild steel hinge pin, anodised complete all as specified and directed.

S&F 300 mm long Aluminium anodized sliding door bolt with hasp & staple (bolt type) fixing clips of sheet cast or extruded section & fixing bolts, sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F steel windows or ventilators, with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars including a shop coat of primer complete all as specified.

All as per srl item No. 37 above but without glazing bars.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, galvanised wire staples, complete all as specified and directed.

S&F 3mm thick frosted sheet glass and glazing with oil putty in square n. exc 0.80 Sqm in each panes fixed any bldg height complete all as specified and directed.

S&F mild steel rolled work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe-410 W (grade E-250) quality-B complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick (BMT) of any colour having tensile strength of 550 Map as in roof covering/cladding to wall, fixing with self tapping screws complete all as specified and directed.

M&L for aluminium anodised snap grid frame work of size 605x605mm for false ceiling with hanging arrangement of 6mm dia G.I. wire (upto 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size and 60mm long and expansion hold fasteners 12.50mm dia 40mm long complete all as specified and directed.

M&L for preparation new plastered surface of wall and applying two coats of oil bound distemper over a layer of 1mm thick Birla putty as base coat and primer etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

Taking down chawkhats or frame with shutter (without taking out shutter from the frame n.exc 1.50 Sqm each and removing from site complete all as specified and directed.

M&L for cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings Converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc to store and rubbish not exc. 50 m etc complete all as specified and directed.

M&L for forming jambs etc, to opening (to foregoing item), including cutting too thing and properly bonding into old work also facing jointing and pointing to match existing work in CM 1:4 complete all as specified and directed.

M&L for making good under cills or over arches, lintels including all pinning when necessary in cement mortar 1:6 etc complete all as specified and directed.

M&L for precast RCC 1:2:4, type B-1 using 20mm graded mechanically crushed stone aggregate as in lintel and shelves etc including necessary form work & exposed surfaces finished even and fair with plain faces including chamfered, weathering etc & set in CM 1:4 complete all as specified and as directed.

Dismantling floor, hearth or wall ceramic tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all specified and directed.

Demolition of brick work built in cement mortar including all quoins, pillars etc but excluding ashlar facings, dressed stone work and pre-cast articles complete all as specified and directed.

Taking down cement or cement lime plaster any description incl racking out joints, hacking for keys, scrubbing down with water etc complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying two coats of oil bound distemper over a layer of 1mm thick Birla putty as base coat and primer etc complete all as specified and directed.

M&L for preparing old decorated plastered surfaces of walls, pilasters, cornices etc. and applying one coat of exterior emulsion paint camouflage pattern complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall, pilasters, cornices etc and applying two coat of exterior emulsion paint in camouflage pattern (two or more colour combination) over one coat of primer complete all as specified and directed.

M&L for anodised aluminium doors (sliding/hanging type) with frame size 101.60X44.45X 2.00 mm thick and shutter aluminium anodised and top rail 47.62X44.45X1.50mm and style 47.5x44.5x1.5 mm, lock rail 83.50X44.45X1.50mm and bottom rail 150.00X44.50X2.50mm and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture1.4mm incl necessary aluminium fittings like aluminium butt hinges 04 Nos, aluminium handles 150mm 02 Nos, aluminium tower bolts 200mm 01 No. mortise lock 4 lever MS, hydraulic door closer of suitable capacity 01 No, aluminium door stopper 01 Nos, jointing cleats, glazing cleats, rubber packing, anodised aluminium shape beading, screws etc with paneling in two parts with 12mm thick prelaminated particle board in lower panel and 5mm thick tinted glass in upper panels incl all fittings& fixture complete all as specified and directed.

M&L for anodised aluminium (sliding/hanging type) windows/ ventilator with frame size 60x40x2.00mm thick and shutter with section bearing bottom 25x18x1.50, top 39.4x17.7 X1.50 mm (suitable for moving over three track fixed over top of frame work , top and side section of size 61.6x 31.75x1.5mm and bearing bottom track of size 61.6x 31.75x1.5mm or fixing with hinges steel wire cloth 0.36mm nominal dia of wire and average width of aperture1.4 mm including necessary aluminium jointing cleats, glazing cleats, rubber packing anodised shape beading, screws etc with 4 mm thick tinted/plain glass in panels including anodised aluminium grill with all fittings & fixture complete all as specified and directed .

S&F factory made solid PVC moulded door shutter 28 to 30mm thick (stile) with 2, 4 or 6 raised pannel design with two mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face in frame at site as per specification and drawing on Sl page No.161 of SSR (part-II) complete all as specified and directed.

S&F in opening Solid door frame (Factory made) of size 50mmx47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as per specification and as per drawing on Sl page 160 of SSR (Part II) complete all as specified and directed.

S&F in repair chromium plated shower roses with or without swivel joints, any size incl fixing to steel pipe or union complete all as specified and as directed.

S&F stainless steel sink with drainage board made out of 0.80mm thick steel sheet for kitchen with plug, washer waste pipe, MS cantilever bracket, connection union overall size 915x460mm with bowl size 410x310x160mm complete all as directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking/WHB plat forms and like including cutting moulding and rounding edges in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for brick work using old size bricks with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L for GI tubing, 15 mm bore 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1 :3 for concealed water tubing, cutting n.exc. 10cm girth complete all as specified and directed.

S&F bib tap 15mm bore, chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F vitreous china water closet squatting pan, 'Orrisa' pattern, size 580x440 mm white, with integral foot rests including connection to trap, and to flushing pipe, anti syphonage pipe etc complete all as specified and directed.

S&F vitreous china coloured wash hand basin counter top oval shape cascade pattern with & including pedestal of size 550X450x190mm (Make-Johnson Model No. P0813PW or equivalent of specified make) with and including 15 mm dia swan neck pillar tap (Make- Johnson Model No. T1804C or equivalent of specified make) brass with capstan head chromium plated screwed with long screwed shank and fly nut screwed complete all as specified.

S&F PVC connection 15mm size with PTMT nuts of length 450 complete all as specified and directed

S&F 32mm PVC waste pipe fixed to WHB & Sink etc complete all as specified and directed (Note minimum length of each pipe should more than 0.70RM).

S&F in repair vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete incl urinal spreader and providing and fixing plugs, bedding urinal against wall in cement mortor 1:2 complete all as specified and directed.

M&L for in repair for vitreous china urinal partition wall for urinal and making good complete all as specified and as directed.

S&F in repair low level flushing cistern PVC 10 ltrs capacity with all internal fittings, bracket and 32mm bore PVC flush pipe, complete all as specified and directed.

S&F in repair stop valve 15mm bore, cast copper alloy, chromium plated with long shank and cup screwed down, high pressure, with crutch of butterfly handle, screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F Soap dish 150mm dia vitreous china white complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in roof padding, roof kerb, coping etc mixed with liquid water proofing compound, surface finished even and fair without using extra cement complete all as specified and directed. Note:-WPC will be measured & paid separately)

M&L for 15 mm thick rendering on fair faces of brick work or on concrete surface in CM 1:3 finished surface even and smooth without using extra cement with using liquid water proofing compound complete all as specified and directed. Note: WPC will be measured and paid separately.

M&L for water proofing treatment to roof surface complete all as specified and directed with the followings: - (a) Applying bituminous based primer confirming to IS:3384-1965 @ 0.30Kg/Sqm (b) Applying APP modified polymeric membrane of weight not less than 3.0Kg/Sqm laid and bonded to the sub strata by heat process, over laps of 100mm shall be sealed/fused by flame torch application as per manufacturer instructions. (c) Screeding 15 mm thick in CM 1:4 as bedding layer using 100% coarse sand. (d) S&F 40 mm thick brick tiles jointed and pointed in CM 1:3 mixed with linseed oil @ 5% by weight of cement.

S&F aluminium chequered grill weight exc 3.5 kg and n.exc. 5.5 kg per sqm with all fittings & fixture complete all as specified and as directed.

S&F continuous piano type hinges MS bright finish or electro galvanized width of flap 40mm when open all as specified.

S&F 75mm size brass handle, cast type, polished bright complete all as specified and directed.

Taking down chawkhats or frame with shutter (without taking out shutter from the frame exc. 1.5Sqm but n.exc 4.00 Sqm each and removing from site complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size straight or curved on plan exceeding 6 metre mean radius built in CM 1:4 complete all as specified and directed.

S&F light colour vitrified, ceramic tiles of size 600x600x8-10mm thick as in floor etc, set & jointed with in neat cement slurry or with adhesive as per manufacturers instructions & pointed in white/colour cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per item No. 86 above but on vertical surface of wall of size 600X100X10mm thick as in dado/skirting including 15mm thick rendering screed in CM 1:4.

S&F anodised aluminium wall partition with anodised aluminium frame of section 101x44.45x2mm thick and intermediate frame 101x44.45x2mm thick including necessary jointing cleats, glazing cleats, rubber packing, anodised aluminium shape beading, screws etc with paneling in two parts with 5mm thick plain glass in upper panels and 5mm thick aluminium composite panel sheet in lower panel complete all as specified and directed.

Cutting holes brick walls built in cement mortar and making good in CM 1:3 or cement concrete 1:2:4 type B-1 exc half brick but not exc one brick thick wall complete all as specified and directed.

S&F 50 micron sun light control film approved fixed on glass pane complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded aggregate as in anchorage block complete all as specified and directed.

S&F PVC (SWR) pipes 110mm single socketed in any length with rubber ring joints complete all as specified and directed.

S&F PVC (SWR) 110mm bend complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:3 on fair faces of brick/concrete surfaces of ceiling and finished even & smooth without using extra cement complete all as specified and directed.

M&L for preparation new plastered surface of ceiling and applying two coats of oil bound distemper over a layer of 1mm thick Birla putty as base coat and primer etc complete all as specified and directed.

M&L for complete removal of existing treatment of ceiling and applying two coats of oil bound distemper over a layer of 1mm thick Birla putty as base coat and primer etc complete all as specified and directed.

M&L for cutting/opening/threading of existing steel water tubing of size upto 25mm dia for and including insertion of tee reducer for branch connection of 15mm bore pipe complete all as specified and directed.

M&L for one light/fan point controlled by one switch point wiring with (FRLS) flame retardant low smoke PVC insulated unsheathed cable 1.5 sqmm with multistranded copper conductor, in and including non metallic PVC concealed conduit not less than 20mm dia with fittings, including all tees, bell mouth tube ends and fixing accessories such as couplers, saddles, pipe hooks etc including provision of sunken pressed steel GI terminal boxes of not less than 1.6mm wall thickness, concealed in wall with modular top cover and plate including (FRLS) flame retardant low smoke PVC insulated copper earth conductor 1.50sqmm connected to common earth and earth dolly complete all as specified and directed.

All as per srl item No. 98 above but for one socket outlet 3 pin 5 amps independent controlled by one switch but not below the main board in the same vertical plane

All as per srl item No. 98 above but for one socket outlet 3 pin 5 amps controlled by one switch on the same board.

S&F switch piano, flush type 5 amp, single pole, one way 240 volt complete all as specified and directed.

S&F socket outlet, 5 pin, 5 amps flush type complete all as specified and directed.

S&F ceiling rose surface bakelite, 65X50mm three terminals complete all as specified and directed.

S&F ceiling fan complete with all electronic fan regulator and accessories of capacity 230V, 1200 mm sweep, BEE 5 star rating complete all as specified and directed. Make: Havells, Model No. ES 50 Premium 5 or equivalent in Bajaj/Crompton.

S&F exhaust fan single phase 230/240 volt AC 300mm sweep, 1400 RPM with painted louvers, metal body, including cutting holes of suitable size in wall, grouting of nuts and bolt etc required for fixing fan and making good to match the existing surface and making connection with twisted copper flexible wire 23/0.0076mm complete all as specified and directed. Make: Havells/Bajaj/CG.

S&F wall mounted batten integrated LED plastic channel with tube of capacity 20 Watt (4ft), integral sleek extruded polycarbonate LED channel with white acrylic cover and integrated electronic driver complete fixed/connect properly complete all as specified and as directed. Make:-Bajaj/Havells/Philips/C&S

All as per Item No. 106 above but for capacity 9-10 watt (2ft).

S&F sub main wiring with two single core PVC insulated cable with 2.5 sqmm nominal cross sectional area stranded copper conductor and one single core green PVC insulated 1.5 Sqmm stranded copper conductor earth continuity cable drawn through with and including non metallic rigid PVC conduit medium grade 20mm bore including accessories concealed in wall including cutting chases in wall and making good disturbed surface to match of wall/ceiling complete all as specified and directed.

S&F factory made epoxy powder coated distribution board SPN 4 ways double door with acrylic top cover (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates complete all as specified and directed.

S&F MCB SP 6 to 32 Amp 240 volts 10 KA breaking capacity 'C' curve complete all as specified and directed.

S&F MCB SPN 40 Amp 240 volts 10 KA breaking capacity 'C' curve complete all as specified and directed.

M/s Aradhana Enterprises

M/s Comfort Air Conditioning and Refrigeration Engineers

M/S SHRI RC YADAV

DEEP ENTERPRISES

ANIRUDH ENTERPRISES

M/S B.P. CONSTRUCTION

M/S NITISH ASSOCIATES