SPECIAL REPAIRS TO ROOF TREATMENT AND JOINERY WORKS IN DOMESTIC AREA AT AF STATION ADAMPUR

Amount

Dismantling brick tiles or terracing tiles, single layer on roof including segregating and stacking serviceable brick tiles and removal of unserviceable brick tiles / brick bats and rubbish outside defence land, complete all as specified and directed.

Demolition of mud on roofs, any thickness, including plaster and leeping plaster and bottom layer of polythene film if any, including removal of retrieved material outside defence land, complete all as specified directed.

Uprooting completely natural vegetation /plants, stems of trees (upto 30 cm girth), grown up on wall, parapets or in roof and making good the damaged/disturbed portion and filling holes in cement mortar 1:3/PCC 1:2:4 to match with the existing surface, complete all as specified directed.

Demolition of cement concrete (un-reinforced), of any description and in any position not otherwise specially provided for and removal of debris outside MoD land, complete all as specified and directed.

Material and labour for rendering 10mm thick in cement mortar (1:4), using water proofing compound as per manufacturer's instructions, on concrete surfaces, finished even and smooth, complete all as specified and directed. Note :- Supply only water proofing compound will be measured and paid for separately.

Supply only integral water proofing compound, complete all as specified and directed.

Material and labour for water proofing treatment of RCC roof consisting as under:- (a) Applying evenly a layer of 85/25 bitumen @1.2 Kg/Sqm over a coat of bituminous primer conforming to IS-3384:1986 @ 0.30litre/Sqm, including preparation of roof surfaces (b) A layer of 3mm thick APP polymeric membrane of weight not less than 3.60Kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/sqm), with properties of high penetration and centre core consisting of 90 micron high molecular high density polyethylene ( MHHDPE) film consisting of five layers, duly sealed at over laps (100mm side lap and 150 mm end lap ) & joints with flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.

Material and labour for plain cement concrete (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregate as in padding on roof, in required thickness to maintain desired slope, finished even and fair to receive tiles/ APP membrane, complete all as specified and directed.

Material and Labour for 40mm thick brick tiles laid on and including 15mm thick cement screed bed in CM (1:6) using grey cement and grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement laid on concrete roof, complete all specified and directed.

All as per serial item No 9 here-in-before (but except brick tiles), complete all as specified and directed. Note : (i) Old serviceable ties as obtained from Serial item No 1 here-in-before shall be reused. (ii) The cost of cleaning and washing of brick tiles for re-use, shall be deemed to be included in the unit rate quoted by the tenderer.

Demolition of brick masonry work built in cement mortar including all quoins, arches, pillars, staging etc. and removal of rubbish outside MOD land, complete all as specified and directed.

Material and labour for brickwork with using subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

Material and labour for brickwork with using retrieved subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), except bricks, complete all as specified and directed. Note : Old serviceable bricks retrieved from demolition vide srl item No 11 here-in-before shall be reused after proper cleaning & washing etc.

Taking down cement plaster on brick or stone walls or concrete surfaces, etc, any description including raking out joints, hacking for key, scrubbing down with water, etc and removal of rubbish outside MoD land, complete all as specified and directed. Note : Rate quoted by contractor shall be deemed to include to necessary scaffolding etc.

Material and labour for rendering 15mm thick in cement mortar (1:4), on brick/concrete surfaces of walls, finished even & smooth without using extra cement , complete all as specified and directed.

Material and labour for rendering 10mm thick in cement mortar (1:6), on brick/concrete surfaces of walls, finished even & smooth without using extra cement , complete all as specified and directed.

Taking up or down existing steel water tubing and connections, 15mm bore for re-fixing or removing from site to store for reuse or credit, including taking down standard fittings, complete all as specified and directed.

Taking up or down existing steel water tubing and connections, 20mm bore for re-fixing or removing from site to store for reuse or credit, including taking down standard fittings, complete all as specified and directed.

Supply and fixing galvanized steel water tubes, 15mm bore, medium grade, with all standard fittings such as bends, elbows, tees etc, concealed/on surface, fixed to walls and ceiling or laid in floors, complete all as specified and directed. Note : Cost of cutting chases as required shall be deemed to be included in quoted rate.

Supply and fixing galvanized steel water tubes, 20mm bore, medium grade, with all standard fittings such as bends, elbows, tees etc, concealed/on surface, fixed to walls and ceiling or laid in floors, complete all as specified and directed. Note : Cost of cutting chases as required shall be deemed to be included in quoted rate.

Fixing only, old steel water tubing, 15mm bore pipe, with all fitings in new or old position (walls, ceiling, floors etc), complete all as specified and directed. Note : 1. Old steel tubing shall be fixed after proper checking, cleaning washing, bleaching etc. 2. Cost of cutting chases as required shall be deemed to be included in quoted rate.

Fixing only, old steel water tubing, 20mm bore pipe, with all fitings in new or old position (walls, ceiling, floors etc), complete all as specified and directed. Note : 1. Old steel tubing shall be fixed after proper checking, cleaning washing, bleaching etc. 2. Cost of cutting chases as required shall be deemed to be included in quoted rate.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for and removing rubbish out sie MoD land, complete all as specified and directed.

Dismantling existing water tanks of size exc 250 Litre but n.exc 500 litre capacity and removal from site to store for reuse or credit, complete all as specified and directed.

Dismantling existing water tanks of size exc 500 Litre but n.exc 1000 litre capacity and removal from site to store for reuse or credit, complete all as specified and directed.

Supply and fixing/hoisting, rotational moulded polyethylene (HDPE) water storage tanks (cylindrical vertical with closed top), 500 litres capacity ‘triple layered’, hoisted and fixed in position including inlet, outlet and drain pipe with plug, complete all as specified and directed.

Supply and fixing/hoisting, rotational moulded polyethylene (HDPE) water storage tanks (cylindrical vertical with closed top), 1000 litres capacity ‘triple layered’, hoisted and fixed in position including inlet, outlet and drain pipe with plug, complete all as specified and directed.

Supply and fixing in repairs PTMT ball valves, suitable for 20 mm bore iron pipe, (weight not less than 210 grams), ISI marked, high pressure, with high density plastic ball , with epoxy coated aluminium rod, complete all as specified and directed.

Supply and fixing in repairs 110 mm dia bore PVC (SWR) pipes, single socketed, in any length, with rubber ring joints, fixed to wall, complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) bends any radius with access door, fixed to pipes with adhesive, complete all as specified and directed.

Disconnecting existing water tanks of capacity exceeding 250 ltrs but not exceeding 500 ltrs, draining out of water, setting aside or lowering if required, making alternative arrangement for water supply to the building and refixing in original position after roof treatment work is over, complete all as specified and directed. .

Disconnecting existing water tanks of capacity exceeding 500 ltrs but not exceeding 1000 ltrs, draining out of water, setting aside or lowering if required, making alternative arrangement for water supply to the building and refixing in original position after roof treatment work is over, complete all as specified and directed. .

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of cement based paint, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame), exceeding 1.5 sqm but not exceeding 4 sqm each and removal, including making good the disturbed surface in CM(1:4) and finishing as per existing specifications and removal of debris outside MOD land, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame), not exceeding 1.5Sqm each and removal, including making good the disturbed surface in CM(1:4) and finishing as per existing specifications and removal of debris outside MOD land, complete all as specified and directed.

Taking down chowkhats or frames exceeding 1.5 sqm but not exceeding 4 sqm each and removal, including making good the disturbed surface in CM(1:4) and finishing as per existing specifications and removal of debris outside MOD land, complete all as specified and directed.

Taking down chowkhats or frames not exceeding 1.5 sqm each and removal, including making good the disturbed surface in CM(1:4) and finishing as per existing specifications and removal of debris outside MOD land, complete all as specified and directed.

Taking down shutters of any description exceeding 1.0 sqm but not exceeding 2.0 Sqm each, from chowkhats/frames and removal to store for reuse or credit, complete all specified and directed

Taking down shutters of any description not exceeding 1.0 sqm each, from chowkhats/frames and removal to store for reuse or credit, complete all specified and directed

Taking down wooden shutters of any description exceeding 1.0 Sqm but not exceeding 2.0 Sqm each, from chowkhats/frames and refixing in the same opening after necessary repair, easing and adusting, jointing replacement/refixing of mongries etc, complete all as specified and directed.

Taking down wooden shutters of any description exceeding 1.0 Sqm but not exceeding 2.0 Sqm each, from chowkhats/frames and refixing in other opening after necessary repair, easing and adusting, jointing replacement/refixing of mongries etc, complete all as specified and directed.

Supply and fixing factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolt to each shutter, steel handle and with glazing bars, dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing no CEAF/STD-185-2012 sheets 1/2 & 2/2.

Supply and fixing factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolt to each shutter, steel handle and without glazing bars, including flat iron 12x3mm for securing wire mesh, dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing no CEAF/STD-184-2012 sheets 1/3 to 3/3.

Supply and fixing factory made box type steel secion ventilators, fixed type with glazing bars and with one shop coat of zinc cromate primer complete all as specified and and directed and shown on Drawing No CEAF/STD-186-2012 Sheet 1/1.

Supply and Fixing Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed.

Supply and fixing factory made pressed steel frames for doors with two rebates, of size 125 mm x 60mm, made out of 1.25mm thick sheet, including PCC 1:3:6 type C-0 filling, one shop coat primer and necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Supply and fixing factory made pressed steel frames for doors with two rebates, of size 105 mm x 60mm, made out of 1.25mm thick sheet, including PCC 1:3:6 type C-0 filling, one shop coat primer and necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Supply and fixing second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue, pinned at joints, complete all as specified and directed.

Supply and fixing factory made shutter, 35 mm thick, 2nd class hardwood (Hollock) rail and style, plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply. The size of rail and stile as per IS: 1003 (Part-I) and as specified in SSR Part-I section 8 clause 8.24(a), kiln seasoned and chemically pressure treated, complete all as specified.

Supply and fixing flush shutters 30mm thick, solid core construction with block board core and plywood face panels commercial type on both sides, both faces covered with decorative face veneer, duly provided with 6mm thick Teakwood lipping on edges, fitted to chowkats, complete all as specified & directed.

Supply and fixing second class hard wood 35 mm thick plain, glazed and skelton factory made shutters, open rebated and prepared to receive glass, gauge etc (without shash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutter as specified in SSR Part I, Section 8, Clause 8.24(a), kiln seasoned and chemically pressure treated , supplied and fitted to chowkats complete all as specified and and directed. Note:- Glass or Wire cloth in panels will be measured and paid separately.

Supply and fixing factory made solid PVC door shutter (conforming to IS-4020) 30mm thick consisting of frame made out of M.S. tubes of 19 gauge thickness & size of stiles, top rail, bottom rails & lock rail all as per shown on drawings in SSR 2010 Pt II, M.S. frame shall have a coat of steel primer of approved make & manufacturer, MS frame covered with 5mm thick heat moulded pre-laminated PVC ‘C’ channel of size 30mm thick, 70mm width out of which 50mm shall be flat & 20mm shall be tapered in 45degree on the either side forming stiles and 5mm thick, 95mm wide pre-laminated PVC sheet out of which 75mm shall be flat and 20mm shall be tapered at 45 degree on the inner side to form top rail & bottom rail and 155mm pre-laminated sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom & lock rail shall be provided on either side of panel. 10mm (5mmx2mm) thick, 20mm wide cross PVC sheet shall be provided as gap inserted to top rail and bottom rail; Paneling of 5mm thick prelam PVC sheet to be fitted with M.S. frame welded/sealed to the stiles & rails with 5mm+2mm thickx15mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive etc. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of "C" channel using PVC solvent adhesive, complete all as specified and directed.

Supply and fix, Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawing in SSR Part-II, in opening, complete all as specified and directed.

Material and labour for steel plain black sheet 1mm thick for steel doors etc, cut ot size, edges beaded if directed, holes punched, includind round headed screw clout nails or rivets and fixed to steel members with plain 40 mm lap joints, welded/riveted seams including bending, turning up mitred angles, stopped ends, outlets etc as required , complete all as specified and directed.

Material and labour for mild steel as in framed work of doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing similar work conforming to Fe-290 Grade E-165, complete all as specified and directed.

Supply and fixing plain sheet glass 3 mm thick, ordinary quality, not exceeding 0.50 Sqm each pane, and glazing with oil putty and securing pins, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, shape, quality or any description) from metal frame including punching or drilling out old glazing pins/ spring clips and providing and fixing new ones, complete all as specified.

Supply and fixing galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed to steel frames with tinned tacks, or galvanised steel wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed.

Supply and fixing in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed to steel frames with tinned tacks, or galvanised steel wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed.

Supply and fixing Aluminium alloy, anodised, sliding door bolts 250mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 12mm dia, complete all as specified and directed.

Supply and fixing butt hinges, medium weight, 75mm long, cold rolled mild steel , complete all as specified and directed.

Supply and fixing butt hinges, medium weight, 100mm long, cold rolled mild steel , complete all as specified and directed.

Supply and fixing butt hinges, 100mm long, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, ISI marked, complete all as specified and directed.

Supply and fixing 200 mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing 150 mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing in repairs 150 mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing in repairs 100 mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing, 150 mm long, extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and directed.

Supply and fixing, in repairs 150 mm long, extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and directed.

Supply and Fixing mild steel 300mm long, ordinary rat tail rod pattern springs including roller and roller plate, complete all specified and directed.

Supply and fixing in repairs mild steel 300mm long, ordinary rat tail rod pattern springs including roller and roller plate, complete all specified and directed.

Supply and fix in repairs hasp & staple, safety type, aluminium anodised, 100mm size, fixed with screws, complete all as specified and directed.

Supply and fixing in repairs cast iron body door closer, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed.

Supply and fixing 140 mm door stopper of aluminium alloy body and tongue , anodised, with hard drawn steel spring fixed in door, complete all as specified and directed.

Supply and fixing in repairs mild steel motice lock vertical type size 100 mm, 4 levers for steel cupboard, complete all as specified and directed.

Material and labour applying two coats of synthetic enamel paint over and including a coat of pink primer, on new wooden surfaces over 10cm width or girth, including preparation of wooden surface, complete all as specified and directed.

Material and labour, applying two coats of synthetic enamel paint over and including a coat of red oxide primer, on new steel surfaces over 10cm width or girth, including preparation of steel surface, complete all as specified and directed.

Supply and fixing18mm/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc, including fixing 18mm wide 6mm thick beading of 1st class HW (Teak) all around, fixed as in repairs, including removal of old to store for reuse or credit, complete all as specified and directed.

Material and labour for First quality, glazed ceramic coloured tiles, 7-8mm thick, of size 300mm x 200mm on vertical surface such as in skirting, dados, risers to steps, etc., including 10mm thick screed or bedding layer in CM 1:4, set and jointed in neat cement slurry @ 3Kg/Sqm, including pointing in white cement mixed with pigment or coloured cement to match the shade of tiles, fixed in repairs, complete all as specified and directed.

Supply and fixing in repairs 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished, complete all as specified.

Supply and fixing in repairs 100 mm long, cast iron window handles, left/right direction, for 'Z' section window , complete all as specified and directed.

Note: The Total amount shall subject to adjustment of credit of Rs.123070.00 for old Materials as per Schedule of Credit.

BHARAT ENTERPRISES

Surya & Gautam Builders