Renovation of Public HEalth Toilets i.e ladies and Gents in the premises of Depot No.IV, CCBSS, at ISBT Sector 43 Chandigarh

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. .2.8

All kinds of soil. .2.8.1

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : .2.10

All kinds of soil .2.10.1

Pipes, cables etc, not exceeding 80 mm dia. .2.10.1.1

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia .2.10.1.2

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : .4.1

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) .4.1.3

1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) .4.1.11

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). .5.3

Centering and shuttering including strutting, propping etc. and removal of form for : .5.9

Suspended floors, roofs, landings, balconies and access platform .5.9.3

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. .5.22

Thermo-Mechanically Treated bars of grade Fe-500D or more. .5.22.6

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: .6.1

Cement mortar 1:4 (1 cement : 4 coarse sand) .6.1.1

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : .6.4

Cement mortar 1:4 (1 cement : 4 coarse sand) .6.4.1

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. .8.2

Granite of any colour and shade .8.2.2

Area of slab upto 0.50 sqm .8.2.2.1

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. .8.5

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. .8.31

Providing and fixing pressed steel door frames confirming to IS:4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm,or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by EIC .10.14

Profile B .10.14.1

Fixing with adjustable lugs split end tail to each jamp .10.14.1.1

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. .11.56

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. .11.56.1

12 mm cement plaster finished with a floating coat of neat cement of mix : .13.7

1:3 (1 cement: 3 fine sand) .13.7.1

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : .13.41

New work (two or more coats) over and including water thinnable priming coat with cement primer .13.41.1

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. .13.8

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: .14.5

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) .14.5.1

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. .15.2

Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) .15.2.2

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and rs wherever required : .17.3

W.C. pan with ISI marked white solid plastic seat and lid .17.3.1

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required .17.1

Kitchen sink without drain board .17.10.2

610x510 mm bowl depth 200 mm .17.10.2.1

Providing and fixing white vitreous china water closet squatting pan (Indian type) : .17.13

Orissa pattern W.C. pan of size 580x440 mm .17.13.2

Providing and fixing CP brass jet heavy duty complete .17.16.A

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. .17.19

10 litre (full flush) capacity-white .17.19.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. .17.28

Semi rigid pipe .17.28.1

32 mm dia .17.28.1.1

Providing and fixing soil, waste and vent pipes : .17.35

100 mm dia .17.35.1

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 .17.35.1.2

75 mm dia .17.35.2

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 .17.35.2.2

Providing and fixing heel rest sanitary bend .17.4

100 mm dia .17.40.1

Centrifugally cast (spun) iron socket &spigot (S&S) pipe as per IS: 3989 .17.40.1.2

Providing and fixing collar : .17.57

100 mm dia .17.57.1

Centrifugally cast (spun) iron socket &spigot (S&S) pipe as per IS: 3989 .17.57.1.2

75 mm dia .17.57.2

Centrifugally cast (spun) iron socket &spigot (S&S) pipe as per IS: 3989 .17.57.2.2

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : .17.58

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : .17.60

100 mm inlet and 75 mm outlet .17.60.2

Centrifugally cast (spun) iron socket &spigot (S&S) pipe as per IS: 3989 .17.60.2.1

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. .18.10

20 mm dia nominal bore .18.10.2

25 mm dia nominal bore .18.10.3

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps,i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall .18.11

15 mm dia nominal bore .18.11.1

20 mm dia nominal bore .18.11.2

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. .18.12

20 mm dia nominal bore .18.12.2

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : .18.17

20 mm dia nominal bore .18.17.1.A

25 mm dia nominal bore .18.17.1

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete .18.18

20 mm dia nominal bore .18.18.2

Providing and fixing uplasticised PVC connection pipe with brass unions : .18.21

45 cm length .18.21.2

15 mm dia nominal bore .18.21.2.1

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : .18.38

20 mm diameter pipe .18.38.2

25 mm diameter pipe .18.38.3

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : .18.46

15 mm dia nominal bore .18.46.1

20 mm dia nominal bore .18.46.2

25 mm dia nominal bore .18.46.3

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (Based on DSR 18.48) .18.48

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 .18.49

15 mm dia nominal bore .18.49.1

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 .18.52

15 mm dia nominal bore .18.52.1

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 .18.53

15 mm dia nominal bore .18.53.1

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. .18.53.A

Cutting holes up to 30x30 cm in walls including making good the same: .18.76

With common burnt clay F.P.S. (non modular) bricks .18.76.1

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc.with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone gregate 20 mm nominal size), including finishing complete so as to make it leak proof. .18.77

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: .19.4

100x100 mm size P type .19.4.1

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 .19.4.1.1

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: .19.30

Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets .19.30.3

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 .19.30.3.1

Dismantling of G.I./C.I. Pipes and taking out the pipes, manully by mechanical means including stacking of pipes with in 50 metres lead as per direction of Engineer-in-Chandigarh. .NSR

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : .NSR

15 mm dia nominal bore .

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards. .NSR

15 mm dia nominal bore .

Providing and fixing CP soap dish holder heavy duty make as approved by EIC .NSR

Providing and fixing CP towel ring round /square with round complete in all respect make as approved by EIC .NSR

Providing and fixing of HCI P trap 4" dia complte in all respect as per entire satisfaction and approvel of make by EIC .NSR

Providing and fixing of C.P. cup heavy duty as per approved make. .NSR

Providing and fixing of curb with CC 1:2:4 complete in all respect. .NSR

Providing and fixing of CP long bend complete in all respect .NSR

Providing and fixing of Standard Urinal size 580x380x350 mm standard with union pvc conction clamp including painting of fifting and cutting ( all inC.P. brassMake jaqur/Hindware/ cera .NSR

Providing and fixing of chinaware oval shape wash basin (snow white ) size 450 x350 x150 mm 2070, make cera /jaqur/ Hindware NSR .NSR

Dismantling of Floor tiles and wall tile complete in all respect .NSR

Providing and fixing pressmatic urinal valve auto cloosing system with built in control cock & wall flange complete in all respect to the entire satisfaction of EIC Make Jaquar , Hindware /Cera .NSR

Providing and fixing urinal partitions curved/rectangular shaped with frosted glass size H: 900 W. 450 glass 8 mmcomplete in all respect make Jaquar/Hindware/Cera .NSR

Providing and fixing of looking glass with PVC beeding 1/4" with plastic hard board or with studs complete in all respect of approved make .NSR

Providing and fixing ISI marked water proof 30 mm thick flush door shutter of pine frame sesoned and treated with seasoned pine filler and 2.5 mm gurjan core ,fungus resistant,eco friendly with 1mm thick lamination on both side with phenol formaldehyde resin conforming to IS:848,complete in all respect of approved make .NSR

Please Enable Macros to View BoQ information