Development of Traffic park in Municipal Area Sri Ganganagar

Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe / foundation and disposal of surplus excavated material at a lead up to 50 m suitable site as per direction of Engineer for following depths, below natural ground / Road top level. In all type soils/ Saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. depth up to 1.5m.

Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering All up to plinth level 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size)

Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded 20mm nominal size stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick

Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 12 mm cement plaster of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar 1:4 (1 cement : 4 fine/ coarse sand)

Providing and fixing of precast concrete interlocking tiles of desired shape of M 30 grade manufactured from fully computerized automatic stationery hydraulic vibrio pressed machine and fully computerized automatic batching plant of class A1/A2 as per BS 6717:2001. The CC interlocking paving blocks be laid on average 50mm. thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer in-charge. The rates to be inclusive of all lead & Lifts etc. complete as per specifications. Tensile splitting strength, abrasion and braking load etc. as per BS 6717:2001, Grey cement. 60mm thick

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Providing and fixing in position precast Reinforced Cement Concrete M15 grade Kilometre stone of standard IRC design, including painting and printing letters etc. as per clause 804 of MoRT&H Specification including all material, labour, machinery. 200 metre stone

Providing and fixing in position Reinforced Cement Concrete Boundary pillars of standard IRC - 25 design, including finishing but excluding printing as per clause 806 of MoRT&H Specification including all material, labour, machinery.

Painting two coats on specified surface with synthetic enamel paint of approved brand and shade, after thorough cleaning and necessary filling to give even shade as per clause 803 of MoRT&H Specification including all material, labour. On new plastered concrete surface

Painting two coats on specified surface with synthetic enamel paint of approved brand and shade, after thorough cleaning and necessary filling to give even shade as per clause 803 of MoRT&H Specification including all material, labour. On steel surface

Painting new letters and figures of specified size, of any shade with first quality synthetic enamel paint, black or any other approved colour to give an even shade as per clause 801 of MoRT&H Specification including all material, labour. Hindi (Matras, Commas and the like not to be measured and paid for. Half letters shall be counted as half).

Painting new letters and figures of specified size, of any shade with first quality synthetic enamel paint, black or any other approved colour to give an even shade as per clause 801 of MoRT&H Specification including all material, labour. English and Roman (Hyphens, commas and the like not to be measured and paid for)

Providing and laying marking of center line and stop line etc with hot thermoplastic compound 2.5 mm thick on road/ plain surface, including reflectorising glass beads @ 250 gms per sqm area with special applicator machine, as per IRC:35 including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control involved. The finished surface to be level, uniform and free from streaks and holes as per clause 803 of MoRT&H Specification including all material, labour, machinery, lighting, guarding and maintenance of diversion.

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 3 metre long and size 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing including all material, labour. 90 cm equilateral triangle

Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide stripes, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and confirming toIRC-79 and the drawings.

Providing and erecting direction and place identifications retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 807.3, fixed over aluminium sheeting 2 mm thick supported on mild steel angle iron post 75 x 75 x 6 mm firmly fixed to ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing. Identification sign board of size upto 0.90 sqm

Providing and fixing CAT’s eye made of aluminium alloy size 75x100x22mm having 21 biconvex lenses embedded in circular disk of AS plastic on each side on road surface complete including all material, labour, diversion.

Supplying and fixing of Single Moulded twin Shank Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/ NH/33023/ 10-97-DC) III Dt 11.06.1997. The height, width and length shall not exceed 50 mm, 100 mm and 100 mm and with minimum reflective area of 13 Sq cm on each side and the slope to the base shall be 35+/-5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 700 Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesiv6 as per manufacturer's recommendation and complete as directed' by the engineer. (manufactured from 3M, Avery or equivalent)

Supplying and fixing glow studs of size 100 X 20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acrylortrite) of ABS having electronically welded micro prismatic lens with abrasion resistant coating as approved by Engineer- in-charge. The glow stud shall support a load of 13635 kg. tested in accordance with ASTM D4280. The slope of retro-reflective surface shall be 35+/ -5 degree to base. The panels on both sides with at least 12 cm of reflective areas up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM 1: 809 as recommended in BS : 873 part 4 : 1973 as per approved sample & manufactures by the Engineer-in-charge.

Providing and fixing “L” type bollard 135cm height made out of 1.25mm thick M.S. sheet welded in conical section having upper dia 15cm and lower dia 20cm with another attachment of 150x150x7mm thick plate and hold fast at bottom, whole body is painted in white stove enamel and red reflective 3 band, each of 7.5cm and one reflective sheet of 15cm dia provided to it complete in all respect including all material, labour, diversion.

Providing and fixing hazard marker made out of 2mm thick M.S. angle iron 25x25x3mm and fixed on channel posts 75x75x6mm and hold fast at bottom whole body is painted in white stoving enamel and 6 nos 5 cm dia reflective sheet on white reflective background with additional border of 1.25 cm all around it complete in all respect including all material, labour, diversion.

Providing and fixing SWISS type hazard marker made out of 2mm thick M.S. sheet size of box is 15x15cm with hold fast at bottom whole body is painted in white stoving enamel paint with white/ high intensity grade prismatic type sheeting on all four side complete in all respect including all material, labour, and diversion.

Providing and laying in place 300mm x 300mm x 16mm cement tactile directional and warning tiles (for a person with visual impairment)of the approved brand and make and specified colour for outdoor floors such as footpath, courtyard, multimodals location etc. laid on 20mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) in all shapes and patterns including grouting the joints with white cement with matching pigments etc. complete as per direction of engineer in-charge

Providing and fixing precast cement concrete M-20 grade (Using mechanical Concrete Mixer) kerb stone top and bottom width 115 and 165 mm respectively, 250 mm high on 150 mm thick PCC M-10 grade foundation as per design, including fixing at site as per clause 408 of MoRT&H Specification including all material, labour, machinery, lighting, guarding and maintenance of diversion.

Painting two coats on plasted concreat surface with synthetic enamel paint of approved brand and shade after through cleaning and neccessary felling to give even shade as per clause 803 and painting new letters and figures of specified size of any shade with firts quality sythetic enamel paint, black or any other approved colour to give an even shade as per clause 801 including all material , labour.