REPAIR/MAINTENANCE OF STEEL AND WOODEN FURNITURE AND WEAVING OF CHARPOY GI AND PAINTING/POLISNING OF WOODEN FURNITURE OTHER MISC WORK AT AIR FORCE STATION AMRITSAR

Amount

Charpoy GI/IP

M&L for removing unserviceable plywood from charpoy GI pipe (FD-220) and supply and fix new 12 mm BWR phenol bonded commercial plywood of size 2000 mm x 900 mm including providing 50mm wide strip made out of 6mm thick plywood for filling gap between plywood sheet and short rails including replacement of bolts and nuts for fixing of plywood all as specified and as directed. Make of plywood - kit ply/Green ply/ National.

M & L for removing of old/unserviceable GI check nut of 32mm dia and supply and fixing of GI check nut of 32mm ISI marked in position and also tightening of all component (Complete Charpoy). Complete all as specified and directed by Engr-in-Charge wherever required

M & L for removal of old/broken threaded long rail from charpoy GI and supply & fix new long rail made of GI tubing 32mm bore (Med grade) (ISI marked) Make : TT Swastic/Jindal/Ravindra both ends threaded complete all as specified and directed by Engr-in-Charge.

M & L for removal of old/broken threaded short rail and fixing short rail made from old long rail obtained from item No 3 above duly threaded both ends complete all as specified and directed by Engr-in-Charge

M & L for removal of old/broken threaded leg from charpoy GI and fixing of leg made from old short rail obtained from item No 4 above (with cap welded on bottom and two Nos of clamp each welded) duly threaded one ends. Complete all as specified and directed by Engr-in-Charge

M & L for removal of old/unserviceable GI Elbow of 32mm dia bore 3 way and supply and fixing of GI Elbow of 32mm bore 3 way ISI marked (Weight of Elbow not less than 450 Gsm) in position and also tightening of all component (Complete Charpoy). Complete all as specified and directed by Eng-in-Charge wherever required

M&L for removing U/S rusted MS flat of charpoy GI pipe and replacing the same with new MS flat of size 40x4mm with two Nos. Nut bolts as directed.

Table 900 x 900 x 760MM

Removing the existing unserviceable table top of Table 900 x 900 x 760MM (FD-1009) and supply and fix new top made of 18mm thick pre-laminated particle board one side teak face including provision of 4mm thick teakwood beading all around complete all as directed

Removing the existing unserviceable/rusted leg of Table 900 x 900 x 760MM (FD-1009) and supply and fix 25 x 25 x 1.6mm thick MS square pipe leg duly welded to the frame and painted with one coat of synthetic enamel paint over a coat of primer all as directed

Supply and fix new PVC shoe suitable to the leg of Table 900 x 900 x 760MM (FD-1009) after removing the unserviceable shoe.

Material and labour of Table 900 x 900 x 760MM (FD-1009) for preparation of old painted steel sufaces by scraping with emary paper, cleaning, dusting and making the surfaces smooth and applying one coat of primer and synthetic enamel paint of olive green shade of approved quality complete all as specified and as directed

Chair computer Revolving

M&L for removing the existing damaged twin wheel casters from chair computer (FD/E6/MAP/01) and supply and fix new caster duly fixed to match with the existing all as specified and as directed .

M&L for repairs to seat from chair computer (FD/E6/MAP/01) and back of Chair providing new tepastry/polister cloth and rubber foam including replacement of arms rest with new arm rest and repairs to gas lifting and swivel machenism to its original condition complete including greasing, painting etc all as specified.

M&L for removing unserviceable PVC arm rest from chair computer (FD/E6/MAP/1) and fix new PVC arm rest as to match with the existing all as specified and as directed.

PVC Base for Chair Computer superior quality

Shocker for Chair Computer/Revolving superior quality

Locker steel

Removing the existing unserviceable handle of Locker steel (FD-1029) and supply & fix 100 mm size new incl all necessary welding etc chromium plated steel handle of approved quality all as specified and shown on drawing

Removing the existing unserviceable hasp & stapple of Locker steel (FD-1029) and supply & fix incl all necessary welding etc new chromium plated steel hasp & stapple of approved quality and appropriate size all as specified and shown on drawing

Removing the existing unservicable/Rusted door shutters (both) of Locker steel (FD-1029), supply and fix new door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, chromium plated hasp & stapple of approved quality and appropriate size incl all naccecry gas/electric welding and painting with one coat of synthetic enamel paint of olive green shade of approved quality over a coat of primer both inside and outside after preparation of surface complete all as specified and shown on drawing.

Material and labour for removing the existing dents/bends of Locker steel (FD-1029) and preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying two coat of synthetic enamel paint of olive green shade of approved quality both inside and outside complete all as specified and as directed.

Almirah steel med

Removing the unserviceable lock of Almirah steel small (FD 67/1032) and tighting of loose parts of the locking device and supply and fix new lock 7 lever with duplicate keys all as specified and shown on drawing (Make of Lock- Harison)

Removing the existing unserviceable 3 way locking device of Almirah steel med (FD 67/1032) and supply & fix new locking device with necessary fittings and painted with one coat of primer and synthetic enamel paint of olive green shade of approved quality to match with existing all as specified and as directed

Removing the existing unserviceable handle of Almirah steel small (FD 67/1032), supply and fix 100 mm size new chromium plated steel handle of approved quality all as specified and shown on drawing

Removing the existing unserviceable leg, supply and fix new leg made of 1mm thick CRCA sheet to match the existing duly gas/elect welded/riveted of Almirah steel med (FD 67/1032) and painted with one coat of synthetic emamel paint of olive green shade of approved quality to match with existing over a coat of primer all as specified and as directed

Removing the existing unservicable/Rusted door shutters (both) of Almirah steel med (FD 67/1032), supply and fix new door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, 3 way locking device with 7 lever brass lock with duplicate keys- 01 No, key hole and painting with one coat of synthetic enamel paint of olive green shade of approved quality over a coat of primer both inside and outside after preparation of surface complete all as specified and shown on drawing (Make of Lock- Harison)

Removing the exisiting unserviceable shelves of Almirah steel medium (FD-67/1032), supply and fix new shelves made of 1mm thick CRCA sheet to match the existing duly welded/riveted and painted with one coat of synthetic emamel paint of olive green shade of approved quality to match with existing over a coat of primer all as specified and as directed.

Material and labour for removing the existing dents/bends of Almirah steel med (FD 67/1032) and preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying one coat of synthetic enamel paint of olive green shade of approved quality both inside and outside complete all as specified and as directed.

Almirah steel large

Removing the unserviceable lock of Almirah steel large (FD-67/1031) and tighting of loose parts of the locking device and supply and fix new lock 7 lever with duplicate keys all as specified and shown on drawing (Make of Lock- Harison)

Removing the existing unserviceable 3 way locking device and suppply of Almirah steel large (FD-67/1031)and fix new locking device with necessary fittings and painted with one coat of primer & synthetic enamel paint of olive green shade of approved quality to match with existing all as specified and as directed

Removing the existing unserviceable handle of Almirah steel large (FD-67/1031), supply and fix 100 mm size new chromium plated steel handle of approved quality all as specified and shown on drawing

Removing the existing unserviceable leg of Almirah steel large (FD-67/1031), supply and fix new leg made of 1mm thick CRCA sheet to match the existing duly gas/elect welded/riveted and painted with one coat of synthetic emamel paint of olive green shade of approved quality to match with existing over a coat of primer all as specified and as directed

Removing the existing unservicable/Rusted door shutters (both), supply and fix new door shutters made of 1mm thick CRCA sheet including chromium plated steel handle 100mm size -01 No, 3 way locking device with 7 lever brass lock with duplicate keys- 01 No, key hole and painting with one coat of synthetic enamel paint of olive green shade of approved quality over a coat of primer both inside and outside after preparation of surface complete all as specified and shown on drawing (Make of Lock- Harison)

Removing the existing unserviceable shelves and supply of Almirha steel large (FD-67/1031) and fix new shelves made of 1mm thick CRCA sheet to match the existing duly welded/riveted and painted with one coat of synthetic enamel paint of olive green shade of approved quality to match with existing over a coat of primer all as specified and as directed.

Material and labour for removing the existing dents/bends of Almirah steel large (FD-67/1031) and preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying one coat of synthetic enamel paint of olive green shade of approved quality both inside and outside complete all as specified and as directed

Table office officer/clerk steel

Removing the existing unservicable/rusted drawer complete of Table office officer/clerk steel (FD-84/1004 ) and supply and fix new drawer complete made of 1mm CRCA sheet including painting with synthetic enamel paint of olive green shade of approved quality over a coat of primer both inside and outside including preparation of surfaces and repairing inter locking system and providing new lock 6 lever to top drawer all as specified and shown on drawing (Make of Lock : Harison/Godrej)

Removing the existing unserviceable/rusted leg/stiffener of Table office officer/clerk steel (FD-841004), supply and fix 25 x 25 x 1.6mm thick MS square pipe duly welded to the frame and painted with one coat of synthetic enamel paint over a coat of primer all as directed

Removing the existing unserviceable lock of Table office officer/clerk steel (FD-84/1004) and supply and fix new lock of 6 levers with duplicate keys including removing dents and adjustment of locking device of drawers for smooth functioning complete all as specified and as directed

Removing the existing unserviceable side panel of table' locker of Table office officer steel (FD-84/1003) and supply & fix new locker made of 1mm CRCA sheet including painting with synthetic enamel paint of olive green shade of approved quality over a coat of primer both inside and outside including preparating of surfaces complete all as specified and as directed

Removing the existing unserviceable table top of Table office officer steel (FD-84/1003), supply and fix new top made of 18mm thick pre-laminated particle board one side teak face including provision of 4mm thick teakwood beading all around complete all as directed.

Supply and fix new PVC shoe suitable to the leg of Table office officer/clerk steel (FD-84/1004) after removing the unserviceable shoe.

Material and labour for removing the existing dents/bends of Table office officer/clerk steel (FD-84/1004) and preparation of old painted steel sufaces by scraping with emary paper, cleaning, dedusting and making the surfaces smooth by applying putty/red oxide primer wherever required and applying one coat of synthetic enamel paint of olive green shade of approved quality both inside and outside complete all as specified and as directed

CChair Excutive Revolving

M&L for removing the existing damaged twin wheel casters from Leatherelte cushioned revolving executive high back chair (TP) and supply and fix new caster duly fixed to match with the existing all as specified and as directed .

M&L for repairs to seat from Leatherelte cushioned revolving executive high back chair (TP) and back of Chair providing new tepastry/polister cloth and rubber foam including replacement of arms rest with new arm rest and repairs to gas lifting and swivel mechanism to its original condition complete including greasing, painting etc all as specified.

M&L for removing unserviceable PVC arm rest supply from Leatherelte cushioned revolving executive high back chair (TP) and fix new PVC arm rest as to match with the existing all as specified and as directed.

M&L for removing the existing damaged twin wheel casters from Leatherelte mid high back chair made of chromium (TP) and supply and fix new caster duly fixed to match with the existing all as specified and as directed .

Chair CBA Steel with/without arms

Removing unserviceable seat frame of chair tubular steel with/without arms from chair steel tubular with/ without arms (FD-75 M) and supply and fix new seat frame made out of shisham wood french polished duly plastic canned in 'Godrej' pattern with plastic cane 2mm width and borders with 4mm wide plastic cane fixed with screws 4 Nos and nuts to the chair frame complete all as per drawing as specified.

Removing broken handle from chair steel tubular with (FD-75M) and replacing with new handle made of shisham wood duly french polished and fixed to the chair tubular with arms with screws of suitable size to the chair frame all as shown on drawing and as directed.

Supply & Fixing of bars MS Flat 25 x 25 x 4mm thick welded at four corner at bottom of the seat only to support from chair steel tubular with/ without arms (FD-75 M) and also screwed with the seat at two places complete all as specified and as directed.

Chair verandah

M&L for removing the unserviceable conduit part from chair verandah FD/MAP-II/06 frame and replace the same with new MS conduit 20mm bore,1.6mm thick, upto 30cm length, made to shape, duly welded all as directed.

M&L for removing of existing torn out/ unserviceable plastic cane from chair verandah (FD-256), prepare steel tubular frame surfaces of chair with emery paper for painting and apply two coat of primer & synthetic enamel paint of white colour of approved quality and recanning the chair fully both seat and back with new plastic cane, white, half round of size 4mm wide including providing new suitable PVC shoes of approved quality and colour all as directed.

WOODEN FURNITUTRE

Chair dining

M & L for removing unserviceable/ broken Rear leg from chair dining (FD-279) and supply and fix new rear leg as to match with the existing, made of shisham wood all as specified and shown on drawings.

M & L for removing unserviceable/ broken Front leg from chair dining (FD-279) and supply and fix new front leg as to match with the existing, made of shisham wood all as specified and shown on drawings.

M & L for removing unserviceable/ broken Rear/front/side rail from chair dining (FD-279) and supply and fix new Rear/front/side rail as to match with the existing, made of shisham wood all as specified and shown on drawings.

M & L for removing unserviceable/ broken Stiffener from chair dining (FD-1105/279) and supply and fix new Stiffener as to match with the existing, made of shisham wood all as specified and shown on drawings.

M & L for removing unserviceable/ broken Back rest from chair dining (FD-279) and supply and fix new Back rest as to match with the existing, made of shisham wood all as specified and shown on drawings.

Removing the existing cane from chair dining (FD-279) and recanning in 'Godrej' pattern with 2mm wide & 0.6mm thick for centre portion and 4mm wide plastic cane for borders all as directed.

M&L for preparation of sufaces by throughly rubbing with emery paper, applying raw seina/burnt seina uniformly from chair dining (FD-279) and polishing with french polish to obtain a glossy finish including fixing 4 Nos nylon buffers at the bottom of the chairs all as specified.

Chair writing

M & L for removing unserviceable/ broken Rear leg from chair writing (FD-250/280) and supply and fix new rear leg as to match with the existing, made of shisham wood all as specified and shown on drawings.

M & L for removing unserviceable/ broken Front leg from chair writing (FD-250/280) and supply and fix new front leg as to match with the existing, made of shisham wood all as specified and shown on drawings.

M & L for removing unserviceable/ broken Rear/front/Side rail from chair writing (FD-250/280) and supply and fix new Rear/front/Side rail as to match with the existing, made of shisham wood all as specified and shown on drawings.

M & L for removing unserviceable/ broken arms from chair writing (FD-250/280) and supply and fix new arms as to match with the existing, made of shisham wood all as specified and shown on drawings.

M & L for removing unserviceable/ broken Back rest from chair writing (FD-250/280) and supply and fix new Back rest as to match with the existing, made of shisham wood all as specified and shown on drawings.

M & L for removing unserviceable/ broken Stiffener from chair writing (FD-250/280) and supply and fix new Stiffener as to match with the existing, made of shisham wood all as specified and shown on drawings.

Removing the existing cane from seat & back of the chair from chair writing (FD-250/280) and recanning in 'Godrej' pattern with 2mm wide & 0.6mm thick for centre portion and 4mm wide plastic cane for borders all as directed.

M&L for preparation of sufaces by throughly rubbing with emery paper, applying raw seina/burnt seina uniformly from chair writing (FD-250/280) and polishing with french polish to obtain a glossy finish including fixing 4 Nos nylon buffers at the bottom of the chairs all as specified.

Sofa set 4/5 seater & Sofa chair With cushion

M&L for removing the old worn/torn out cushion from sofa set 3 seater FD-281 and tapesty cloth from seat and back of sofa and providing new cushion of 32 density cool foam of size 560 x 530x100mm thick including provision tapesty cloth of approved shade & quality (cost of tapestry cloth shall be more than Rs. 200/- per metre)all over a cover of lining cloth duly covered and stiched over the cushions complete all as directed. Make : sleepwell/curlon.

Material and labour for preparation of wooden surfaces with sand/emery paper and applying french polish of approved quality to achieve uniform smooth texture and high glossy finish after filing holes with beas wax for the sofa set 3/4/5 seater all as specified and shown on drawing FD-281.

Side Board

Removing the existing unserviceable door shutters (both) of side board (FD-372) and supply and fix new door shutters (both) as to match with the existing, made of 18mm thick teak face Pre-laminated particle board exterior grade duly providing 6mm thick teak wood beading all round including all fittings and fixtures all as shown on drawing and as directed Note :- (a) Knob shall be aluminium anodized (dark brown chromium plated of approved size and quality) (b) Hinges shall be 50mm of approved quality.

Removing the existing unserviceable front portion of the drawer of side board (FD-372) and supply and fix new front portion of the drawer as to match with the existing made out of 18mm thick teak face Pre-laminated particle board with laminated finish including new knob all as specified and shown on drawing.

Removing the exisiting unserviceable top from the side board (FD 372) and supply and fix new top as to match with the existing, made out of 18mm thick teak face Pre-laminated praticle board with laminated finish duly providing 4mm thick teak wood beading all round duly french polish all as specified and as shown on drawing.

Removing the existing unserviceable plywood from sides (both) of side board (FD-372) supply and fix new 3.5mm thick one side teak face plywood on sides (both) as to match with the existing all as specified and shown on drawing

Removing the existing unserviceable back of side board (FD 372) and supply and fix new back as to match with the existing , made out of 6mm thick commercial ply wood all as specified and shown on drawing

Polishing outersides of the side board from top (FD-372) and foot board including legs and long rails of the with french polish obtaining a glossy finish after preparation of the outer surfaces by throughly rubbing with emery paper all as specified.

Table Dining 04/06 Person

Removing the existing unserviceable leg from the Table dining for 04/06 persons and supply and fix new leg made of shisham wood to match with the existing all as specified and shown on drawing FD-30/273 &239.

Removing the existing unserviceable top rail (long/front) from Table dining for 04/06 person and supply and fix new rail made of shisham wood to match with the existing all as specified and shown on drawing FD-30(M)/273&239.

Removing the existing unserviceable top rail (short/side) Table dining for 04/06 person and supply and fix new rail made of shisham wood to match with the existing all as specified and shown on drawing FD-30 (M)/273 & 239.

Removing the existing unserviceable top from the Table dining for 04/06 person and supply and fix new one as to match with the existing made of 18mm thick teak face pre-laminated particles board one side laminated with 4mm thick teak wood beading duly french polish all as specified and shown on drawing FD-30(M)/273&239.

Material and labour for preparation of wooden surfaces with sand/emery paper and applying french polish of approved quality to achieve uniform smooth texture and high glossy finish after filing holes with beas wax for the Table dining for 04x06 person all as specified and shown on drawing FD-30(M)/273&239.

Teapoy

Removing the existing unserviceable leg from the Teapoy and supply and fix new leg made of shisham wood to match with the existing all as specified and shown on drawing FD-278.

Removing the existing unserviceable top rail (long/front) from Teapoy and supply and fix new rail made of shisham wood to match with the existing all as specified and shwon on drawing FD-278.

Removing the existing unserviceable top rail (short/side) from Teapoy and supply and fix new rail made of shisham wood to match with the existing all as specified and shown on drawing FD-278.

Removing the existing unserviceable top from the Teapoy and supply and fix new one as to match with the existing made of 18mm thick teak face pre-laminated particle board one side laminated with 4mm thick teak wood beading duly french polish and toughened glass 10mm thick top (Mk - Atul/Gobain) all as specified and shown on drawing FD-278.

Material and labour for preparation of wooden surfaces with sand/emery paper and applying french polish of approved quality to achieve uniform smooth texture and high glossy finish after filing holes with beas wax for the Teapoy all as specified and shown on drawing FD-278.

Table peg

Removing the existing unserviceable leg from the Table peg and supply and fix new leg made of shisham wood to match with the existing all as specified and shown on drawing FD-384.

Removing the existing unserviceable top rail (short/side) from the Table peg and supply and fix new rail made of shisham wood to match with the existing all as specified and shown on drawing FD-384

Removing the existing unserviceable top rail (long/front) from Table peg and supply and fix new rail made of shisham wood to match with the existing all as specified and shwon on drawingFD-384

Removing the existing unserviceable top from the Table peg and supply and fix new one as to match with the existing made of 18mm thick teak face pre-laminated particle board one side laminated particle board with 4mm thick teak wood beading duly french polish and toughened glass 10mm thick top (Mk- Gobain/Atul) all as specified and shown on drawing FD-384.

Material and labour for preparation of wooden surfaces with sand/emery paper and applying french polish of approved quality to achieve uniform smooth texture and high glossy finish after filing holes with beas wax for the Table peg all as specified and shown on drawing FD-384.

Table writing

Removing existing unserviceable top of the table writing (FD-275) and supply and fix new top as to match with existing made out of 18mm thick pre-laminated particle board one side laminated finish duly providing 4mm thick teak wood beading all around duly french polish complete all as specified and shown of drawing

Removing the existing unserviceable leg of the table writing (FD-275) and supply and fix the same with new one as to match with existing made out of shisham wood complete all as specified and shown on drawing

Removing the existing unserviceable leg (short) of the table writing (FD-275) and supply and fix the same with new one as to match with existing made out of shisham wood complete all as specified and shown on drawing

Removing the existing unserviceable side/bottom rail of the table writing (FD-275) and supply and fix the same with new one as to match with existing made out of shisham wood complete all as specified and shown on drawing

Removing the existing unserviceable back of the table writing (FD-275) and supply and fix the same with new one as to match with existing made out of 6mm thick plywood commercial complete all as specified and shown on drawing

Removing the existing unserviceable side of the table writing (FD-275) and supply and fix the same with new one as to match with existing made out of 18mm thick partical board one side laminated finish complete all as specified and shown on drawing

Removing the existing unserviceble stiffner of the table writing (FD-275) and supply and fix the same with new one as to match with existing made out of shisham wood complete all as specified shown on drawing

Removing the existing unserviceable drawer of the table writing (FD-275) and supply and fix the same with new one as to match with existing made out of 18mm thick partical board one side laminated finish including provision of knob compete all as specified and shown on drawing. Note:- Knob shall be aluminium anodised (Dark Brown) chromium plated of approvd size and quality.

Removing the existing unserviceable cupboard complete of the table writing (FD-275) and supply and fix new cupboard complete made out of 18mm thick partical board one side teak face finish including 4mm teak wood beading on front side including fitting/fixtures complete all as specified and shwon on drawing. Note:- (a) Knob shall be aluminum anodized (dark brown chromium plated of approved size and quality). (b) Hinges shall be 50 mm of approved quality.

Material and labour for preparation of wooden surfaces with sand/emery paper and applying french polish of approved quality to achieve unifrom smooth texture and high glossy finish after filling holes with beas wax for table writing all as specified and shown on drawing (FD-275)

Dressing Table Gents/Ladies with mirror

M & L for removing the existing unseviceable looking mirror from Dressing Table Gents/Ladies with mirror (FD-379/251) and supply and fix new looking mirror of 5.5mm thick of appropriate size along with 6mm thick commercial plywood back of the mirror including minor repairs all as specified and shown on drawings(Ladies). Note : Make of Mirror should be of Modiguard/St Gobain/Atul.

M & L for removing the existing unseviceable looking mirror and wooden beading from Dressing Table Gents and supply and fix new looking mirror of 5.5mm thick 1.50 m long and 600mm wide along with 50 mm thick teak wood beading all around and fixed of with 6mm thick commercial plywood on back of the mirror including polishing, batten of appropriate size repairs all as specified and shown on drawings(Gents). Note : Make of Mirror should be of Modiguard/St Gobain/Atul.

Material and labour for removing the unserviceable drawers from the dressing Table Ladies with mirror (FD-379/251) and supply & fix new drawer made out of 18mm thick prelaminated particles board one side laminated finish all as specified and shown on drawing

Polishing outersides of the Dressing table from (FD-379/251) with french polish obtaining a glossy finish after preparation of the outer surfaces by throughly rubbing with emery paper all as specified.

Note: The Total amount shall subject to adjustment of credit for old Materials as per Schedule of Credit.

M/S INDAN FURNITURE MART (BID ID -3489271)

ASHOK KUMAR MAHAJAN (BID ID -3490566)

NAVEEN TRADERS (BID ID -3491025)

RATTAN CHAND CHANDAN AND CO (BID ID -3490624)