Providing Renovation for Conference Room with Air Condition and Interiors for the Office of Vigilance at IHC HAL Bangalore

Name of the Individual / Firm / Company: * Mandatory

Type of ownership

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Address for correspondence:

PAN No.:

Goods and Service Tax ID No.

Contact details

Please Enter Contact person Name

Pls Enter Mobile No

Registered Contractor

Related Document to be Uploaded to eProcurement Portal * Category: E= 75 Lakhs - Lessthan= 100Lakhs F= 50Lakhs - Lessthan 75 Lakhs G = 25Lakhs - Lessthan 50 Lakhs H = 10Lakhs - Lessthan 25 Lakhs I = 5Lakhs - Lessthan 10 Lakhs J = 2Lakhs - Lessthan 5 Lakhs K = Lessthan 2Lakhs

I.T Returns for past 03 assessment years

Annual financial turn over during the last 3 years, ending 31st March 2025

TURN OVER IN Rs.

Pls Enter Turn over in Rupees for all the 3 years

ESI & PF Nos with proof

Remarks if any

Bank(s) details: [Copy of ECS and cancelled cheque leaf to be uploaded]

Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)

Solvency Certificate Details

Pls Enter Details to 'Name of the Bank' , 'Date of Issue','Value in Rs

Experience of having successfully completed similar works during last 7 years ending on the previous day of submission of tender [Work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender.

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Please enter Details for Work No 1

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Pls Enter Details for Work No II

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Pls Enter Details for Work No III

Details of person holding the power of Attorney (If different from contact person)

Related Document to be Uploaded to eProcurement Portal

Pls Enter Details for Person holding Power of Attorney

DECLARATION I

DECLARATION II

Pls Accept the Delaration II

Specification

Demolishing Nominal cement concrete 1:3:6 or richer mix (i/c equivalent design mix) manually / by mechanical means including disposal of material within 50 metres lead, etc., all complete as directed by Engineer-in-Charge.

Dismantling doors, windows and clerestory windows (steel or wood) of area 3 Sq m and below shutter including chowkhats, architrave, holdfasts, etc., complete and stacking within 50 metres lead, etc., all complete as directed by Engineer-in-Charge.

Demolishing brick work built in cement mortar manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead, etc., all complete as directed by Engineer-in-Charge.

Dismantling tile work For thickness of tiles 10mm to 25mm in floors and roofs / walls laid in cement mortar including stacking material within 50 metres lead, etc., all complete as directed by Engineer-in-Charge.

Taking down cement / lime palstering of any desription on brick walls inlcuding raking out joints, scrubbing, etc., all complete as directed by Engineer-in-Charge.

Taking out existing wooden door shutter / MS shutters / aluminum shutters / frames repair by cutting, painting, etc., and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc., as required, etc., all complete as directed by Engineer-in-Charge.

Cement mortar (1:6) plastering 20mm thick for brick / concrete surfaces, finished smooth with trowel including lime rendering for interior faces of walls surfaces including scaffolding, curing, etc., all complete as directed by Engineer-in-Charge.

Providing and laying Vitrified Matt / Antiskid finishtiles in floor in different sizes (thickness to be specified by the manufacturer) of size [600 x 600]mm with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.30 Kgs/Sq m including grouting the joints with white cement and matching pigments, etc., The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily, etc., all complete as directed by Engineer-in-Charge.

Providing & fixing fly proof wire gauze of stainless steel grade 304 ( wire guage) of 0.50mm wire and 1.40mm aperture on both sides, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing With float glass panes of 5mm thickness (weight not less than 12.50 Kgs/Sq m)glazing in aluminium door, window, ventilator shutters and partitions, etc., with EPDM rubber / neoprene gasket, etc., as per the architectural drawings, etc., all complete as directed by Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth, etc., all complete as directed by Engineer-in-Charge.

Wall painting with 2 coats of premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams / litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour, etc., all complete as directed by Engineer-in-Charge.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams / litre, etc., all complete as directed by Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour and shade of one or more coats on old work of wood / steel, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing factory made uPVC white colour casement / casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners [100 x 8]mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. SUB HEAD : 9 - WOOD & PVC WORK 684 Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water.

Providing and fixing powder coated aluminum sections (minimum thickness of powder coating is 50 micron) for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket, etc., Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasteners to be paid for separately)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required powder coated aluminum sections (minimum thickness of powder coating is 50 micron), etc., all complete as directed by Engineer-in-Charge.

Supplying and fixing of venetian blinds / vertical blinds consisting of control unit idler, head of rail, roller tube, bottom rail operating chain, brackets and clamps /nuts / bolts / of approved clour / pattern including necessary supporting hangar holders / screws, etc., all complete as directed by Engineer-in-Charge.

Providing & laying flamed finish Granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent (of any type) tiles 18mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete (Black Z or equivalant) screeding of 20mm in cement mortar 1:4 laying tiles in neat cement slurry bedded and jointed with grey cement slurry & painted with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types, moulding, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing chromium plated brass butt hinges of size [100 x 70 x 4]mm (ordinary type)with necessary chromium plated brass screws, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing ISI marked oxidised M.S. sliding door bolts (Copper oxidized as per IS 1378) of size [250 x 16]mm with nuts and screws, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) (Copper oxidized as per IS : 1378) of size [150 x 10]mm with necessary screws, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing specified frame work consisting of battens [50 x 25]mm fixed with rawl plug and drilling necessary holes for rawl plug, etc., inclduing priming coat and cll complete using klin seasoned and chemically treated hollock wood, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing 12mm thick commercial ply conforming to IS : 1328 BWR type plain lining with necessary screws / nuts & bolts / nails, including a coat of approved primer on one face and fixed on wooden / steel frame work / Plastered surfaces, etc., all complete as directed by Engineer-in-Charge. (Frame work shall be paid for separately)

Providing & Fixing decorative high pressure 1.0mm thick laminated sheet of plain / wood grain in gloss / matt / suede finish to required pattern and combination as per the drawings etc on plywood with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality / brand, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing 35mm thick flush door shutters conforming to IS :2202 (Part I) non-decorative type of approved brand/make, core of block board construction with frame of 1st class hard wood & lipping with 2nd class teak wood battens 25mm minimum depth on all edges and well matched commercial 3ply veneering with vertical grains or cross bands including ISI marked Stainless Steel butt hinges with necessary screws and face veneers on both faces of shutters and making rectangular vision panel of 0.10Sq m with 6mm thick clear heat strengthened glass, etc., all complete as directed by Engineer-in-Charge.

Supplying and fixing of following door fittings and fixtures, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing bright finished brass handles of 125mm size with screws.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws.

Providing and fixing bright finished brass tower bolts of [250 x 10]mm (barrel type) with necessary screws.

Providing and fixing bright finished brass 100mm mortice latch and lock with min. 6 levers and a pair of lever handles of approved quality with necessary screws.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35kgs and door width upto 700mm), with necessary accessories and screws.

Providing and fixing aluminium sliding door bolts (aldrop) of [250 x 16]mm, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws.

Providing and fixing aluminium handles 125 mm, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws .

Providing and fixing 50mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws.

Providing and fixing FALSE CEILING with 12.50mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks of approved brand) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/Sq m (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.60mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.50mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of [25 x 10 x 0.50]mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels [45 x 15 x 0.90]mm running at the spacing of 1200mm centre to centre, to which the ceiling section 0.50mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.50mm, at 450mm centre to centre, shall be fixed in a direction perpendicular to

Disposal of moorum / building rubbish / malba / similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10km for all lifts, etc., all complete as per directions of Engineer-in-Charge. Note - item to be applicable in urban areas having directions for restricted hours for movement / plying of load carrying motor vehicle of 3.50Cu m or more.

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine, etc., with auto closing spring loaded hinges (hydraulic type), etc., all complete as per direction of Engineer-in-Charge. (Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make / brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished, etc., all complete as per direction of Engineer-in-Charge.

Providing and fixing special quality chromium plated brass cupboard locks of size 40mmwith six levers of approved quality including necessary screws, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates, etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts, etc., of required size, on the top of the floor or the side of waist slab with suitable arrangementEngineer-in-Charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners, etc.,)

Rupees Eleven Lakh Fifty Three Thousand Two Hundred Seventeen and Four Paise Only

Supplying, Installation, Testing & Commissioning of 36W Panel light 2x2 ft., of Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm) body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) <19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output .LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).

Supplying and fixing 16 way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required, as per CPWD specification.

Providing and fixing 125A MCCB rating and 36KA breaking capacity and 4 pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required, as per CPWD specification.

Supply, installation, testing and commissioning of 63A, 4P MCB, 10kA, C Curve in the exisitng DB/powder coated enclosure.

Supplying and fixing 5 A to 32 A rating, 240V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of double poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supply and fixing on wall/ partition wall using necessary mounting arrangements for 105x50mm size DLP-PVC adaptable trunking system with separation partition for laying power and Data/Telephone cables/wires with full top cover, necessary accessoires such as end caps, flat angle, T joints, external/internal angle, flat junction, Body joint, cover joint, required cabling accessories etc., complete in all respects as directed by Engineer-in-charge.

Supply and fixing on wall/ partition wall using necessary mounting arrangements for 80x50mm size DLP-PVC adaptable trunking system including cover and with separation partition for laying power and Data/Telephone cables/wires with full top cover, necessary accessories such as end caps, flat angle, T joints, external/internal angle, flat junction, Body joint, cover joint, required cabling accessories etc., complete in all respects as directed by Engineer-in-charge.

Supply, fabricating and installing of size 100 x 50 x 2mm thick with 1.6mm thick perforated GI cable trays with cover including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling/fixing to the wall/RCC beam/iron structures as per site requirement complete in all respects and as directed by Engineer in charge.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.

2 x 6 sq. mm + 1 x 6 sq. mm earth wire

2 x 4 sq. mm + 1 x 4 sq. mm earth wire

2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire

Supplying, drawing, Installation, Testing and commissioning of 2 runs of CAT6 UTP LSZH 23AWG Twisted Pair Cable in existing conduit/ on surface, Category 6 Unshielded Twisted Pair, 4 pair should be complied as per UL/ETL verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in the range of 6.1mm nominal with Operating Temperature Range : -5° to +60°C, Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg etc. complete as required.

Supplying and drawing 4 pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of 20mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of 25mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following 2sets of 6A switch & sockets on the existing DLP trunking including 6M clip on support with suitable modular plate and necessary interconnections as per site requirement and as directed by E-I-C.

Supplying and fixing following 1set of 6/16A switch & sockets on the existing DLP trunking including 3M clip on support with suitable modular plate and necessary interconnections as per site requirement and as directed by E-I-C.

Supplying and fixing two nos RJ 11 Telephone jack socket on on the existing DLP trunking including 2M clip on support with suitable modular plate and necessary interconnections as per site requirement and as directed by E-I-C.

Supply, Fixing, testing & Commissioning of two nos RJ 45 Data socket/CAT6 I/O on the existing DLP trunking including 2M clip on support with suitable modular plate and necessary interconnections as per site requirement and as directed by E-I-C.

Supply, installation, testing and commissioning of 65" Smart TV with Brightness (Typ.) : 400 nits; Resolution : ULTRA HD (3,840 x 2,160); Improved Design with Slim Depth; HDMI and USB ports; including 15 meter length of HDMI cable. Make & Model of the display may be LG-65UR640S or equivalent in other approved makes (LG/Samsung/Sony).

Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of 1.5TR capacity(5 Star BEE rating) with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 420C. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature).

Rupees Three Lakh Eighty Six Thousand One Hundred Forty Two and Fifty Seven Paise Only

Rupees Fifteen Lakh Thirty Nine Thousand Three Hundred Fifty Nine and Sixty One Paise Only

Approximate Amount Put to Tender

Rupees Two Lakh Seventy Seven Thousand Eighty Four and Seventy Two Paise Only

Rupees Eighteen Lakh Sixteen Thousand Four Hundred Forty Four and Thirty Three Paise Only