ADDN / ALTN AND SPECIAL REPAIRS TO BLDG NO P 62 (SINGLE LIVING ACCN) UNDER GE (CENTRAL) KHADKI

Amount

M&L for providing 40 mm thick cement concrete M-15 grade (Nominal Mix) using 12.5 mm graded stone aggregate as in roof padding required to maintain desired slope complete all as specified and as directed by Engineer-in-Charge

Taking down/removing existing water proofing treatment from RCC roof slab including removal of plaster bed below felt / membrane and removing the same to low laying area out side the premises and M & L for 10 mm thick screeding/rendering in cement mortar 1:3 on concrete roof surface, using liquid Water Proofing Compound as per manufactures instruction and finishing surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge Note. Liquid Water Proofing Compound shall be measured and paid separately under relvant item this BOQ

Supply only liquid water proofing compound.

M & L for applying APP (Atactic Poly Propylene) bitumen membrane 3mm thick APP modified weight not less than 3.60 Kg/Sqm reinforced with non woven polyester fibre of weight 160 gms/sqm as centre core and without multiple layers of polyethylene, finished on top and bottom with 7 micron thick flammable polyethylene, applied by thermo fusion using LPG torch on the bottom portion of the membrane, after applying a coat of bituminous primer 0.40Kg/Sqm over roof (An overlap of 100mm & 150mm shall be provided on sides and ends respectively) finally apply a coats of bitumastic aluminium paint over the membrane complete all as per manufacturers instructions Note:- Water proofing treatment to RCC roof slab shall be got executed from manufacturers applicator or through their authorise applicator only .

M&L for waterproofing treatment to RCC sunken slab complete all as specified and as directed by Engineer-in-Charge

S&F of UPVC 50 mm dia for spout pipe in sunken floor complete all as specified and directed

Demolition of cement concrete of any description and in any position not other specifically provided and removing the demolished concrete to low laying area out side the premises complete all as specified and as directed by Engineer-in-Charge

Demolition of RCC (Reinforcement cut as reqd to facilitate to demolition) etc with diamond cutter and removing the demolished concrete to low laying area out side the premises complete all as specified and as directed by Engineer -in-Charge

Dismantling of stone slab/flooring of any description laid, bedded and pointed in any mortar complete all as specified and as directed.

M&L PCC M-5 grade (Nominal Mix) using 40mm grade aggregate as in mass concrete or as in sunken portion or floor complete all as specified & directed

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing the rubbish to low laying area out side the premises complete all as specified and as directed by Engr-in-Charge

M&L for 25 mm thick Cement concrete M-15 grade (Nominal Mix) using 20 mm graded stone aggregate as a level course for receiving floor tiles complete all as specified and as directed by Engr-in-Charge

M&L for 100 mm thick Cement concrete M-15 grade (Nominal Mix) using 40 mm graded stone aggregate in sub bases, floors and paving for receiving floor tiles complete all as specified and as directed by Engineer-in-Charge

M&L coloured Non Skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles and laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge

M&L coloured Glazed ceramic tiles on vertical surface of size 450mm X 300mm X 6 to 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles and laid over and including cement plaster 10mm thick as in backing coat in CM 1:4 complete all as specified and directed by Engr-in-Charge

M&L coloured Non Skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0 18 but not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles and laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge

M&L coloured Non skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.18 sqmbut n exc 0 36 sqm, as in skirting to match the ceramic couloured light shade floor tiles etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles and laid over and including 10 mm thick backing or rendering coat of plaster in cement mortar 1:4, complete all as specified and directed by Engr-in-Charge

M&L for 20 mm thick Granite slab as in kitchen slab, steps etc machine cut bedded and jointed with grey cement and pointed and using marble dust with admixture of pigment to match with shade of granite including cutting and polshing/rounding edges laid over & including 15 mm thick screed bed in CM 1:4 all as directed by Engineer-in-charge complete all as specified and as directed by Engineer-in-Charge

Taking down cement plaster on brick or stone walls, ceiling etc. including raking out joints, hacking for key, scrubbing down with water complete including removing the same to low laying aera out side the primeses complete all as specified and as directed by Engineer-in-Charge.

M&L for rendering 10mm thick on fair faces of brick work or concrete surface in cement mortar 1:6 finishing surface even & smooth complete all as specified and as directed by Engineer-in-Charge

M&L rendering 15 mm thick (10mm + 5mm) plaster on fair face of brick work in CM 1:4 and finishing surface even and fair by mixing liquid water proofing compound as per manufacturers instructions complete all as specified and as directed by Engineer -in-Charge. Note: Liquid WPC shall be measured & paid seprately under relevant item of this BOQ

M & L for rendering 5mm thick in CM 1:3 on fair faces of concrete surface as in ceiling finishing surface even & smooth complete all as specified and as directed by Engineer in-Charge

M & L for preparing of newly plastered surfaces of wall and applying two coats of distemper oil emulsion (OBD) over a coat of primer over wall care putty not less than 1mm thick finishing surface even and smooth to receive primer complete all as specified and as directed by Engineer-in-Charge

M & L for complete removal of existing treatment from old surfaces of wall and applying two coats of distemper oil emulsion (OBD) over a coat of primer over wall care putty not less than 1mm thick finishing surface even and smooth complete ail as specified and as directed by Engineer-in-Charge

M & L for complete removal of existing treatment on external surfaces of walld applying two coats of weather proof acrylic exerior grade paint (100%) Acrylic over one coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed by Engineer-in-Charge

M&L for preparation newly plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exerior grade paint (100%) Acrylic) over one coat of seif primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed by Engineer-in-Charge.

M & L for preparing newly plastered surfaces and applying three coat of white wash on ceiling complete all as specified and as directed by Engineer-in-Charge

M & L for complete removal of old finishes from exsistng surfaces of ceiling including preparing the surfaces and applying three coat of white wash on ceiling complete all as specified and as directed by Engineer-in-Charge

M&L for preparation of old steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st quality) complete all as specified and as directed

M&L framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings; framework of water tanks and similar work con- forming to Fe 290. Gde-E-165 complete all as specified and as directed by Engineer-in-Charge

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, including all necessary preparation over 10 cms width or girth complete all as specified and as directed by Engineer-in-Charge

Hacking out old broken glass (any thickness size, quality or description) from frames glazed with putty or fixed with beads complete all as specified and as directed by Engineer-in-Charge

M&L for 3mm thick sheet glass ordinary quality and glazing clips, rubber packing in exc 0.5 sqm each pane complete all as specified and as directed by Engineer-in-Charge

S&F in repairs stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-Charge

Taking down Chowkat or frames with shutters without taking of shutters from the frames exc 1.5 Sqm but not exc 4Sqm each complete all as specified and including making good disturbed wall surfaces/jambs with cement plaster in 1:4 of thickness as required at site or disturbed masonry, if any, in PCC M-10 grade ( Nominal Mix) using 20 mm graded stone aggregates finished even & smooth using extra cement all as specified and directed.as directed by Engineer-in-Charge

Taking down Chowkat or frames with shutters without taking of shutters from the frames n. exc 1.5 Sqm each complete all as specified and including making good disturbed wall surfaces/jambs with cement plaster in 1:4 of thickness as required at site or disturbed masonry, if any, in PCC M-10 grade ( Nominal Mix) using 20 mm graded stone aggregates finished even & smooth using extra cement all as specified and directed. as directed by Engineer-in-Charge

S & F Pressed steel door frame of size 125 x 60mm and 1.25mm thick one or more rebated for doors incl necessary fixing lugs, hinges lock strike plate, etc complete all as specified and directed.

Taking down shutters of any description exc. 1sqm but n.exc.2sqm each complete all as specified and as directed by Engineer-in-Charge

S&F 105x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and as directed by Engr-in-Charge.

M&L PCC M-10 grade (Nominal Mix) using 12.5mm graded stone aggregate as in filling of MS door frames complete all as specified and as directed by Engr-in-Charge

S & F 35 mm thick IInd class HW glazed and skeleton shutter, open rebated and prepared to receive glass, gauze, etc (without such bars), edges of ramming plain, chamfered or rounded, fitted with cut and mitred beads for scuring glass, etc size of shutters as specified in SSR-I, Section 8.24(a) supplied and fitted to chowkat complete all as specified and as directed by Engineer-in-Charge

M&L for 35 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side one face is covered either decorative face veneer with lipping/frame to match with nails, color and pattern complete all as specified and as directed by Engr-in-Charge

Supply and fix 100mm butt hinges, medium weight, cold rolled mild steel, IS Marked. fixed to angle iron chowkats including welding complete all as specified and as directed by Engr-in-Charge.

S&F for Aluminium sliding door bolts, plate type, with stainless steel bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 300mm long complete all as specified and directed

Supply and fix aluminium handles 150 mm cast type anodised complete all as specified and directed

S&F for aluminium anodised barrel tower bolt 200mm long complete all as specified and as directed by Engineer-in-Charge.

M&L painting to wooden surfaces of any description over 10 cm width or girth including prepration of new or untreated wooden surface and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specifie

M&L painting to wooden surfaces of any description over 10 cm width or girth including prepration of old wooden surface and applying two coat of synthetic enamel paint complete all as specified

S&F new double action hydraulic floor springs of approved brand and manufacturer (conforming to IS) for aluminium doors including cutting and making good the floor as required at site complete all as specified and as directed by Engineer -in-Chargeby Engineer-in-Charge

S& F 20-25 mm thick Machine cut cudappah stone slab laid over and including cement screed bed or bedding layer 15 mm thick in cement mortar 1.4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed

Chamfering to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed

S&F Plain, aluminium sheeting 0.56mm thickness alloy 31000 H4 in ridges, hip, valley gutter, drip and straight flashing (length and girth) as fixed

S&F MS PVC coated Curtain Rod 25 mm dia 1.8mm thick of approved quality with two number decoorative design as approved 3mm thick bracket fixed in brick/ concrete wall and same finished knobs end of curtain rod completed all as specified and directed.

S&F plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F in repair 18mm thick HDHMR BOARD exterior grade including any coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. Make: Action Tessa/Greenply/Century

S&F in repair stainless steel cabinet/drawers handle having a length of 250mm and shape all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating Gl based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws including dismantling old roof sheet CGI/PGI complete all as specified & directed by Engineer-in-Charge

M & L Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe 410-0 or Fe 310-0 (Brackets over 10kg each to be measured under 'Structural Steel')

Excavating in post holes or similar holes each n exc 0.5 cum, getting out in hard and dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good the surface

M&L for Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, stone concrete block or slab shelves etc. making good, cutting not exc 10 cm girth complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Supplying & fixing to walls and ceiling 16 mm outer dia CPVC pipe SDR13.5 and plain CPVC SDR11 fittings complete all as specified and as directed.

Supplying & fixing to walls and ceiling 20 mm outer dia CPVC pipe SDR13.5 and plain CPVC SDR11 fittings complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store all as specified and directed for 40mm bore of pipe.

Supplying & fixing to walls and ceiling 40 mm outer dia CPVC pipe SDR13.5 and plain CPVC SDR11 fittings complete all as specified and as directed.

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed

S&F in repairs vitreous china wash basin white, counter top basin size 430x375x130mm, excluding taps, waste chain & plug & porcelain stopper but cutting for and pinning in ends of brackets including waste coupling and waste pipe all as directed Make: ESC-WHT-933 of CERA or equivalent make given under list of Makes

S&F Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed

S&F in repair of pillar taps long body swan neck chromium plated cast copper alloy with capstan heads, screwed down high pressure with or without lettered "Hot or 'Cold with long screwed shanks and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed. Make: ORI-CHR-109021 or equivalent make given under list of Makes

S and F in repairs for vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests (IWC) (excluding flushing cistern and flush pipe) including connection to down or out going pipe and to flushing pipe anti syphonage pipe etc of approved quality complete all as specified and directed

Supply and fix in repairs for dual flow 10 Itrs capacity PVC/HDPE low level flushing cistern, white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) but including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, seat cover complete, all as specified and directed,

S&F health faucet chromium plated (ABS Body) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook fixing to 15 mm bore of pipe all as specified and directed.

Supply and fix PVC connection 15 mm dia with CP nuts of length 600 mm long complete all as specified and directed

Supply and Fix in repair PVC (SWR) floor trap, with grating 75 mm including jointing with solvent complete all as specified and as directed by Engineer-in-Charge

Supply and Fix in repair PVC nahani Trap, with grating 75 mm including jointing with solvent complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repair for fancy type stop valve, cast copper alloy, fency type, chromium plated, screwed down, high pressure, with capstan head handle, screwed both ends for iron pipe or for unions, with long shank and cup (concealed type), bore dia 15 mm with PTMT nipple (min wt 15 gm-18 gm) to extend length complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repairs shower rose size 125 mm chromium plated with or without swivel joints, including fixing to 15 mm dia steel pipe or union complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repairs fancy type bib taps, CP brass, fancy type with crutch or butterfly handle screwed for iron pipe for brass ferrule 15mm dia with PTMT nipple (min wt 15 gm-18 gm) to extend length complete all as specified and direc

S&F in repairs Soap dish brass CP with screws complete all as specified and as directed by Engineer-in-Charge.

S&F for towel rail of CP fixed 20mm dia, D type 60cm long between flanges with and incl CP brass screws and complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repair 20 mm size gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

Supply and fix in repair 40 mm size gunmetal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S&F in repairs 40mm size ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and as directed by Engineer-in-Chargeby Engineer in charge.

Supply and fix for rotational moulded LLDPE water storage tanks 5000 Itrs capacity (as per IS: 12701), tripple layered (cylindrical vertical with closed top) hoisted and including taking down existing unserviceable overhead tank of any capacity complete all as specified and directed

Supply and fix for rotational moulded LLDPE water storage tanks 2000 Itrs capacity (as per IS: 12701), tripple layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia brass float valve and polyethylene ball including taking down existing unserviceable overhead tank of any capacity complete all as specified and directed

Supply and fix for rotational moulded LLDPE water storage tanks 1000 Itrs capacity (as per IS: 12701), tripple layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia brass float valve and polyethylene ball including taking down existing unserviceable overhead lank of any capacity complete all as specified and directed

S & F Factory made internal PVC moulded door frame of size 50x47mm single revated made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02. Nos of 150 mm brackets of 15x15 mm MS square tube The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and directed

S&F Factory Made Solid FRP Moulded Door Shutter with flush door core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site with wood free EPS complete all as specified and as directed by Engineer -in-Charge

S&F aluminium anodised barrel tower bolts of extruded section 150 mm long complete all as specified and as directed by Engineer-in-Charge

Supply and fix aluminium handles 100 mm cast type anodised complete all as specified and directed

S&F 75 mm long Butt hinges, medium weight, cold rolled mild steel, and fixed

Taking down PVC SWR pipes any radius in any position fixed to wall / floor inci connected fittings clamps etc complete all as specified and directed

Supply and fixing 110 mm dia bore PVC 'P' trap complete all as specified and directed

Supply and fixing 110 mm dia bore PVC bends any radius with access door complete all as specified and directed

Supply & Fix 110 mm dia bore PVC pipes single socketed Type B, in any length with rubber ring joints, fixed to walls of laid in trenches with arrangement complete all as specified and as directed by Engineer-in-Charge

Supply & Fix 110 mm bore PVC vent cowl complete all as specified and as directed by Engineer -in-Charge

Supply and fix PVC branch piece, single (single Y) equal or unequal 110 mm bore with access door complete all as specified and as directed by Engineer-in-Charge

Supply and fix PVC junction single, (Single 'T') equal or unequal of 110 mm bore complete all as specified and as directed by Engineer-in-Charge

S & F PVC reducer bore of pipe 110 mm complete all as specified and as directed by Engineer-in-Charge

S & F 75 mm bore PVC pipes single socketed Type B in any length with rubber ring joints fixed to walls with arrangement complete all as specified and directed

S & F 75 mm bore PVC bends any radius with access door complete all as specified and as directed by Engineer-in-Charge

Supply and fix 75 mm bore PVC reducer complete all as specified and as directed by Engineer-in-Charge

Supply and Fix 75 mm bore PVC junction single, (Single 'T') equal or unequal of complete all as specified and directed

S&F Stack clamps for 75mm dia bore of pipe out of flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed by Engineer-in-Charge

S&F Stack clamps for 100mm dia bore of pipe out of flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed by Engineer-in-Charge

Demolition and breaking up drain pipes (salt glazed ware AC/RCC) drain pipes set in cement mortar, dia of pipe 150mm complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware AC/RCC) drain pipes set in cement mortar, dia of pipe 200mm complete all as specified and directed.

Material and labour for cement concrete M-7.5 grade (Nominal Mix) using 40 mm graded coarse stone aggregate in bed to drain pipes of 150 mm bore Concrete bed s including packing under, and haunching against the sides of pipes after they are laid and tested, in complete all as specified and as directed by Engineer-in-Charge

Material and labour for cement concrete M-7.5 grade (Nominal Mix) using 40 mm graded coarse aggregate in bed to drain pipes of 200 mm bore Concrete bed s including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and as directed by Engineer-in-Charge

Material and labour for reinforced concrete pipes, 150 mm bore, Class NP-2, laid and jointed complete with collars complete all as specified and as directed by Engineer -in-Charge.

Material and labour for reinforced concrete pipes, 200 mm bore, Class NP-2, laid and jointed complete with collars complete all as specified and as directed by Engineer-in-Charge.

M&L for precast reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate as in manhole covers, septic tank slab etc set in CM 1:6 complete all as specified and as directed by Engineer-in-Charge

M&L cement concrete M-15 grade (Nominal Mix) 20 mm graded aggregate in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses. string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directing

Material & Labour for rendering 10 mm thick in cement mortar 1:4 on brick work or concrete masonry wall surface finished even and smooth without using extra cement mixed with water proofing compound (WPC) complete all as specified and directed. NOTE: Liquid WPC shall be measured and paid separatelyunder relevant item of this BOQ

M&L for mild steel TMT bar 10mm dia and over cut to length, bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge.

M&L for mild steel TMT bars, 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by Engineer-in-Charge.

Excavating in trenches, in any type of soil n exc 1.5 m wide and n exc 1.5m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out

Demolition of brick work or stone/boulder masonry, built in cement mortar mortor incl all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick (old size) work with flyash bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 etc complete all as specified and directed

Material and labour for brick work with flyash bricks (old size), straight or curved on plan exc 6m mean radius in half brick walls, in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm

M&L for hardcore of broken stone or boulders of gauge n exc 63mm, deposited spread and levelled in layers n exc 15cm thickand rammed to a true surface

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and taking out old paver block with bedding layer complete all as specified and directed.

M & L for 75mm thick PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate) as in plinth protection complete all as specified and directed

M & L for Cement concrete M-7.5 grade (Nominal Mix) using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed

M & L for 75mm thick M-7.5 grade (Nominal Mix) using 40mm graded stone aggregate as in sub base for paver block complete all as specified and directed

M&L for Roughening surfaces of old detoriated RCC/concrete surfaces horizontal or vertical by hacking, picking, sweeping clean and washing down with water to remove dust and repairing the same G+1 Bldg (Celing edges& top) with PMM ready made concrete of approved make and finished complete all as specified and as directed by Engineer-in-Chargeupto GF slab.

M & L for use and waste of steel form work to soffits of suspended slabs such as roof slab, Chajja and landings etc not exc 200mm thick (horizontal or sloping) for fair finished surfaces of concrete flat complete all as specified and as directed by Engineer in-Charge.

M&L for steel doors of angle or other sections, hinges or steel hanging door fittings Fe-410W, grade E-250 exclusive of steel sheetings incl hanging fastening or fixing complete incl removal of existing doors from the site

M&L for MS black sheet 1.6mm thick fixed to steel doors with rivet or welding complete all as specified and directed

S&F aluminium powder coated (minimum thickness of powder coating shall not be less than 50 micron of approved colour) window with shutter and frame including with two side hung shutter with 4mm thick tinted glass and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing handle, lock rubber beading and glazing clips with cill etc; fabricated using following aluminium powdwer coated section conforming to catlogue of ' Jindal' or of equivalent make given under list of makes complete all as specified and directed by Engineer in charge. (a) Frame-20513, 21034 (b) Handle (side)-20606 (c) shitter inter lock-20724 (d) Shutter glass -20509 (e) Shutter wire mesh -20511 (f) Glazing clips-19352 Note:- Unit rate quoted shall deemed to include the cost of 4mm thick tinted glass and stainless steel wire cloth 0.36mm nominal dia & 1.18 mm width aperture.

S & F aluminium powder coated (minimum thickness of powder coating shall not be less than 50 micron of approved colour) window three track sliding window with shutter and frame including two shutters with 4mm thick tinted glass and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing handle, lock, rubber beading and glazing clips with cill etc; fabricated using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make given under list of makes complete all as specified and directed by Engineer-in-Charge. (a) Bottom Frame-20620 (b) Top Frame & vertical-20621 (c) Handle (side)-20606 (d) shitter inter lock-20724 (e) Shutter top & Bottom -20844 (f) Glazing clips-19352 Note:- Unit rate quoted shall deemed to include the cost of 4mm thick tinted glass and stainless steel wire cloth 0.36mm nominal dia & 1.18 mm width aperture.

S&F louvered aluminium powder coated (minimum thickness of powder coating shall not be less than 50 micron of approved colour) ventilators with adjustable louvers fixed with and including 4mm thick frosted glass louvers and shall be fly proof with stainless steel wire gauge of 0.36mm dia and 1.08mm aperture fixed to frame with aluminium beading and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make given under list of makes and rubber beading etc all as directed:- (a) SP 20048 (b) Glazing clips 19352 (Note:- Cost of glass louvers & wire cloth shall be included in the quoted rate of item. Note:- Unit rate quoted shall deemed to include the cost of 4mm thick frosted glass and stainless steel wire gauge of 0.36mm dia and 1.08mm aperture .

S&F Aluminium single leaf door on pivots along with hydraulic door closer (Aluminium Extruded section), door lock, handles, 5.5mm thick plain glass in top and bottom panel, fixed with rubber beading and glazing clips with cill and using anodised sections as given in 'JINDAL' or of equivalent make given under list of makes Catalogue complete all as directed by Engineer-in-Charge. a) Rectangular tube 14005 b) Shutter vertical 19501 c) Shutter top rail 19503 d) Shutter Middle rail 20060 e) Shutter Bottom rail 19511 f) Glazing clips 19352 Note:- Unit rate quoted shall deemed to include the cost of 5.5mm thick plain glass.

S&F Aluminium double door on floor spring along with 5.5mm thick plain glass and along with door lock, handle MS clamp etc and complete with following aluminium anodised section as given in 'JINDAL' catalogue all as directed by Engineer-in-Charge. a) Door frame partition - 14005 b) Door vertical - 19501 c) Door Top rail - 19503 d) Door Middle rail - 20060 e) Door Bottom rail - 19503 Note:- Unit rate quoted shall deemed to include the cost of 5.5mm thick plain glass.

S&F aluminium Door Closer hydraulically regulated, designation No. 2 universal type, suitable for door shutter of 701 to 850mm in width and of weight between 36 to 60 kg and fixed with door complete all as specified

Taking down copper/aluminium point wiring ( light, fan, socket, power ) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surface of walls, floors, etc

Taking down carefully unserviceable Sub main wiring of any size and type, removing material from for taking credit and making good the disturbed surfaces of walls, ceilings etc

Taking down old and unserviceable main incoming MCB DB TPN/ main switch including MCCBs/MCBs and making good the disturbed surface all as directed specified and directed.

M & L for point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories along with one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one light point or one fan/Ex fan point controlled by one, one way switch including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switch, regulators or bell push and casing capping terminal box for mounting ceiling rose/ holders etc all as specified and directed by Engr-in-Charge.

One light / fan point controlled by one,one way switch on independent board

One three pin 5 Amp socket outlet on independent board

One three pin 5 Amp socket outlet point on same board

All as per item No 145.00 but FRLSH copper stranded cable of size 2.5 sq mm for 3/6 pin socket outlet 15 amp on one independent board. along with all fitting and accessories complete all as specified and as directed by Engineer -in-Charge by Engr-in-Charge.

Material and Labour for replacement old unsv Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLSH cable 1100 Volts grade drawn through in and including PVC casing capping of required size with all fittings and accessories along with green colour FRLSH Copper conductor cable of size 1.5 sqmm as earth lead for one light point controlled by two, two way switch and connected to earth dolly PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switch, regulators or bell push and casing capping terminal box for mounting ceiling rose/ holders etc incl dismantling taking down old unserviceable point wiring and making good to disturbed surfaces complete all as specified and as directed by Engineer -in-Charge by Engr-in-Charge.

M & L for sub main wiring with two single core PVC insulated multi stranded FRLSH Copper conductor cable of size 6 sqmm drawn through in and including PVC Conduit of suitable size with all accessories and one single core green colour FRLSH Copper conductor cable of size 6 sqmm as earth wire and connected to earth dolly and making good to disturbed surfaces . NOTE: -Two run of 6 sqmm cable with one run 6 sqmm earth wire and one run of PVC Conduit of suitable size shall be be measured as one unit length.

M & L for sub main wiring with four single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 10sqmm (Nominal area) drawn through in and including PVC conduit of suitable size with all fittings and accessories along with one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 10 sqmm as earth lead and connected to earth dolly and making good to disturbed surfaces all as specified and directed. NOTE:- Four run of 10sqmm cable with one run 10sqmm earth wire and one run of PVC Conduit of suitable size shall be be measured as one unit length.

S&F 5 Amp switch Piano flush type single pole one way all as specified and as directed by Engr-in-Charge.

S&F 5 Amp switch piano type two way all as specified and as directed by Engr-in-Charge.

S & F Angular Lamp holder of PVC/ Polycarbonate type with back plate all as specified and as directed by Engr-in-Charge.

S&F flush type electronic fan regulator with 5 step type,120 W, AC 240 Volts, 50 Hz all as specified and as directed.

S&F socket flush type 6 amps, 5 pin, 230v all as specified and as directed by Engr-in-Charge.

S&F switch socket combination multipurpose 2-in-1 flush type 3 pin 16 amps and 3 pin 6 amps, 230v

S&F ceiling rose surface Bakelite three terminal all as specified and as directed by Engr-in-Charge.

S&F in replacement old unsv Sheet metal enclosure SPN 08 way (MCB DB) Double door, 240 Volts AC all as specified and as directed by Engr-in-Charge.

S&F in replacement old unsv Sheet metal enclosure SPN 12 way (MCB DB) Double door, 240 Volts AC all as specified and as directed by Engr-in-Charge.

S&F Vertical MCB distribution board, as MCB TPN incomer, IP 43 protection, Double door, metal enclosure, TPN, 415 Volts, 4 way incl dismantling taking down unsv one all as specified and directed by Engr-in-Charge.

S&F MCB TPN 40 to 100 Amps, 415 volt 10 KA complete all as specified and as directed by Engineer -in-Charge by Engr-in-Charge.

S&F MCB, SPN (Double Pole) 32 amps, 240 Volts, 10 KA ‘’C” curve all as specified and directed by Engr-in-Charge.

S&F MCB, Single Pole, 5 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve all as specified and directed by Engr-in-Charge.

S&F in replacement old unsv LED Light batten 20 watt, 4 feet AC sleek and seamless profiled extruded polycarbonate batten with an efficient diffuser to illuminate work and retail spaces with three core flexible copper conductor cable from ceiling rose complete all as specified and as directed by Engineer -in-Charge by Engr-in-Charge.

S&F in replacement old unsv LED Light batten 10 watt, 2 feet AC sleek and seamless profiled extruded polycarbonate batten with an efficient diffuser to illuminate work and retail spaces with three core flexible copper conductor cable from ceiling rose complete all as specified and as directed by Engineer -in-Charge by Engr-in-Charge.

S&F LED lamp 12 watt, CDL, B-22 (Pin type), 230V, PF-0.95 (min) all as specified and directed by Engr-in-Charge.

Supply and fixing LED building light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by Engineer -in-Charge.

M & L for replacement of earthing complete and providing GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and including 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling, necessary excavation and earth work complete including taking out old earthing material complete all as specified and as directed by Engineer -in-Charge

Supply, laying and testing cable XLPE insulated screened pvc bedded galvanised steel strip or wire armoured electric power cable (heavy duty )1100 volts grade with stranded aluminium conductor of size 3.5 core 120 sq mm complete all as specified and as directed by Engineer -in-Charge .

Supply, laying and testing cable XLPE insulated screened pvc bedded galvanised steel strip or wire armoured electric power cable (heavy duty )1100 volts grade with stranded aluminium conductor of size 3.5 core 35 sqmm all as directed by Engineer-in-charge

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of cable and getting out in soft loose soil complete all as specified and as directed by Engineer -in-Charge

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of cable and getting out in soft disintegrated rock complete all as specified and as directed by Engineer -in-Charge.

Removing of excavated material ( disintegrated rock ) n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by Engineer -in-Charge.

Supply and lay double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of underground cable of size 50 mm outer dia with all fittings such as clamps. coupler etc laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection all as specified Note:- Excavation and earth work shall be measured and paid separately under relevant item of this BOQ

Supply and lay double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of underground cable of size 120 mm outer dia with all fittings such as clamps. coupler etc laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection all as specified. Note:- Excavation and earth work shall be measured and paid separately under relevant item of this BOQ

M&L for road cutting upto 300mm deep and 200mm wide for crossing GI water pipe line through road including making good the disturbed surface by filling mass concrete complete all as specified and directed.

Cutting existing GI water pipe line 50/80 mm dia in position for inserting tee/specials for branch connection of 50 mm size complete all as directed.

M&L for Laying in trenches/fixed to wall galvanised steel water tubing 25 mm bore, medium grade with and including all medium grade fittings complete all as specified.

M&L for Laying in trenches/fixed to wall galvanised steel water tubing 40 mm bore, medium grade with and including all medium grade fittings complete all as specified.

S&F in repair gun metal gate valve with iron wheel head, screwed both ends for iron pipes 25mm bore complete all as specified and directed.

Horizon Construction (BID ID -3324805)

S S ENTERPRISES (BID ID -3324919)

Mehta Construction Co. (BID ID -3324234)

H S TAKHI (BID ID -3323952)

Mukund Engineers and Contractors (BID ID -3322264)

UNIQUE ENGINEERS (BID ID -3325387)

SHREE KRISHNA INFRASTRUCTURE (BID ID -3325120)

M/s L. K. Agarwal (BID ID -3325224)

S.R.M.K Enterprises (BID ID -3325340)

Sunbud Multiventures Private Limited (BID ID -3325188)

Bidder Name

H S TAKHI

S S ENTERPRISES

Mehta Construction Co.

United Sales Corporation

UNIQUE ENGINEERS

M/s L. K. Agarwal

S.R.M.K Enterprises

SHREE KRISHNA INFRASTRUCTURE

Horizon Construction

Mukund Engineers and Contractors

Sunbud Multiventures Private Limited