GE863/EWS-T-39 OF 2022-23

Amount

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillet, complete, all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete, all as specified and directed.

Taking down chowkats or frames not exc 1.5 sq.m each but with shutters (without taking off shutters from the frames) including removing from site, complete, all as specified and directed.

Taking down chowkats or frames exc 1.5 sq.m but n.exc 4 sq.m each but with shutters (without taking off shutters from the frames). including removing from site, complete, all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in framed work, complete, all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level), complete, all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil, complete, all as specified and directed.

M&L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation, filling in mass concrete etc, complete, all as specified and directed.

Demolition of brick work, block masonry or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar, complete, all as specified and directed.

Dismantling of wrought iron or mild steel work any description and fixed in any position, complete, all as specified and directed.

M &L for pre-cast cement concrete type C1 (1:3:6) using 20mm graded stone aggregate as in block masonry with solid blocks, exc 10cm in width and setting in cement mortar (1:6), complete, all as specified and directed.

M & L for 40 mm thick Plain Cement Concrete 1:2:4 Type B0 (using 12.5 mm well graded stone aggregate) as in damp proof course (DPC) to horizontal or vertical surfaces including necessary form work, and and including WPC as per manufacturer's instructions complete, all as specified and directed.

M&L Reinforced cement concrete M-30 design mix (20 mm well graded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete, all as specified and directed.

M&L Reinforced cement concrete M-30 design mix (20 mm well graded stone aggregate) in Columns, pillars,piers,posts and struts, complete, all as specified and directed.

M&L Reinforced cement concrete M-30 design mix (20 mm well graded stone aggregate) in Beams, cantilevers, bressummers, complete, all as specified and directed.

M&L Reinforced cement concrete M-30 design mix (20 mm well graded stone aggregate) as in Chhaja, complete, all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete, all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete, all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases od columns , raft and raft beams , sides and soffits of foundation and plinth beams and similar work vertical or better for rough finished surfaces of concrete, complete, all as specified and directed.

M&L Form work to pillars, posts, struts, piers, columns and stachions with rough finished, square, rectangular or polygonal concrete surfaces, complete, all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, bands, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete, complete, all as specified and directed.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5 cm but n exc 10cm wide, complete, all as specified and directed.

M&L for rendering 5 mm thick on concrete surface of walls in cement mortar 1:3 finished even & smooth without using extra cement, complete, all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement plaster 1:4 finished even and smooth (without using extra cement), complete, all as specified and directed.

M & L for rendering 10mm thick on fair faces of brick or concrete surfaces in cement plaster 1:6 and finished even and smooth (without using extra cement), complete, all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2, using 40mm well graded stone aggregate as in Sub base of flooring/hardstanding , complete, all as specified and as directed.

M & L for machine cut kota stone slab flooring 20 to 25 mm thick over and including 20 mm thick screed bed laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and morror polishing, complete, all as specified and directed.

M&L for machine cut kota stone slab 20-25 mm thick as in riser/skirting/dado etc,laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, including cutting, rubbing and mirror polishing, complete, all as specified and as directed.

M&L for 75 mm thick Cement concrete (1:3:6) type C2, (using 40 mm well graded stone aggregate), as in plinth protection, finishing cement concrete surface fair and even without using extra cement laid in alternate panels, complete, all as specified and directed.

S & F 1.25 mm thick pressed steel frame size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete, all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C-1 (using 20 mm well graded stone aggregate) as in filling pressed steel frame, hold fast etc, complete, all as specified and directed.

S & F 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete, all as specified and directed.

S & F of 35 mm thick (Batten thickness) 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without shash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and sizes of the members of shutters as specified in clause No . 8.24 (a) of MES schedule part – I (Specifications - 2009), supplied and fitted to chowkhats, complete, all as specified and directed.

S&F Steel windows/ventilator with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete, all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete, all as specified and directed.

S & F of rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters, running rails and guides for sliding doors fixed with angle cleat and other connecting plates confirming to Fe – 410-W (Gde E-250 ) Quality ' A', complete, all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment including welding, complete, all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling of size 605x605 mm including hangers 6mm dia G I (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G I flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed.

M&L for false ceiling with gypsum board of size 12 to 15 mm thick, perforated type, factory made, matt finish surface / pre-painted surface, 600 x 600 mm in size and and fixed in exisiting aluminium snap grids 605 X 605 mm as in ceiling, complete, all as specified and directed.

S & F in repairs 20 mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc, complete, all as specified and directed.

S & F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with overall length of cover plate 140 mm, complete, all as specified and directed.

S&F 100 mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, complete, all as specified and directed.

S & F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete, all as specified and directed

S&F 125 mm long MS pressed handle oval type stove enamelled black fixed with screw to shutter, complete, all as specified and directed.

S & F in repair mild steel 300mm ordinary rat tail rod pattern springs, including roller and roller plate, complete, all as specified and directed.

S & F galvanised mild steel wire cloth , 0.56 mm nominal dia of wire and average width of aperature 1.18 mm, fixed with tinned tacks, or galvanised wire staples complete, all as specified and directed.

M & L sheet glass, 4mm thick ordinary quality and glazing with oil putty or beadings in square not exc 0.5 sqm in each pane, complete, all as specified and directed.

M & L for preparation of new plastered surface of wall and applying two coats of distemper oil emulsion over a coat of chalk whiting as a preparatory to distempering, complete, all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete, all as specified and directed.

M & L for preparation of new wooden surface of any description not otherwise described and exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of prink primer, complete, all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel of any description , over 10 cm in width or girth not otherwise described applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete, all as specified and directed.

Taking down carefully copper/aluminium point wiring from existing points (light, fan, socket or power) alongwith complete fittings such as switches ,ceiling rose, pendent holder, sketch fitting & regulator etc. including making good to the disturbed surfaces of wall, roof and floor etc. to match with the existing surfaces, complete, all as specified and directed.

Taking down Old U/S light fittings ( Tube light, bulk head, ceiling light, mirror light, bldg light etc) of any type, complete, all as specified and directed.

Taking down carefully old MCBs/Isolators, DB's, changeover etc any type by unscrewing from board, complete, all as specified and directed.

M&L for point wiring using approved colour coding as per IS, 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continous earthing in & incl PVC casing & caping with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box sheet on top for fixing switches, sockets etc all as specified for one light point/ fan/ Bell point controlled by one switch, complete, all as specified and directed

All as per Srl item No 56 here-in-before but controlled with one 3 pin socket outlet 5 Amp on same board with other switches with cables 1.5 Sqmm, complete, all as specified and directed.

All as per Srl item No 56 here-in-before but controlled with one 3 pin socket outlet 5 Amp on independent board with other switches with cables 1.5 Sqmm, complete, all as specified and directed.

All as per Srl item No 56 here-in-before but controlled with one 3 pin socket outlet 15 Amp on independent board with other switches with cables 2.5 Sqmm, complete, all as specified and directed.

Supply and fixing in replacement of switch piano type 5 Amp, 230 Volt, flush button single pole one way, complete, all as specified and directed.

S&F in replacement of socket outlet 3 pin 5 Amp, 230 Volt flush type, complete, all as specified and directed.

Supply and fixing in replacement of switch piano type 15 Amp, 230 Volt, flush button single pole one way, complete, all as specified and directed.

Supply and fixing in replacement socket outlet 3 pin 15 Amp 2-in-one 230 Volt flush type, complete, all as specified and directed.

S&F stepped type electronic fan regulator flush type on existing phenolic laminated sheet etc, complete, all as specified and directed.

S&F in replacement of LED lights fitting 1x20W, 220V, AC retro fit type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitbale size from ceiling rose, complete, all as specified and directed.

S&F LED light fitting 1x9W/1x10W bulkhead luminaires with IP65 protection including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete, all as specified and directed.

S&F in replacement ceiling rose, 3 terminal with ISI mark, complete, all as specified and directed.

S&F in replacement of junctions boxes ,plastice, round, four terminals, complete, all as specified and directed.

S&F in replacement lamp holder, PVC/Polycarbonate type with black plate suitable batten fittings, complete, all as specified and directed.

S&F of sheet metal enclosure double door for DBs single pole and neutral for 8 way 240 volt, complete, all as specified and directed.

Supply and fixing miniature circuit breaker (MCB) SP , rating 240V, 10KA 'C' curve, with current carrying capacity 5 to 32 Amp in the MCB DB complete with connection testing and commissioning, complete, all as specified and directed .

Supply and fixing miniature circuit breaker (MCB) SPN , rating 240V, 10KA 'C' curve, with current carrying capacity 40 to 63 Amp in the MCB DB complete with connection testing and commissioning, complete, all as specified and directed .

Material & labour in repair earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr depth below ground level at any type of strata) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. Connected with galvanised earth wire 4 mm dia by means of bolts, nuts hook nuts and washers as earth lead including concrete chamber of PCC 1:3:6 type C1 (using 20mm graded stone aggregate) with fair finish, internal surface of concrete chamber shall be given internal dia 300mmx300mm, 15mm thick plaster in CM 1:4) funnel with wire mesh, RCC pit cover of 320x320x80mm size in (1:2:4) Type B1 (using 20mm graded stone aggregate ) reinforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1 (2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm bore dia light grade GI pipe for protection and watering pipe of GI 20 mm bore, medium grade, including all excavation and earth work and connecting the earthing wire, including testing on completion complete all as specified and directed. Note : (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick reinforced with XPM weighting not less than 4kg/sqm in lieu of CI cover.

S&F in replacement of 1100 Volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4 mm suspension wire twin core cable flat or circular of size 16 sqmm, complete, all as specified and directed.

M&L for dismantling of house service brackets, any type, complete, all as specified and directed.

S&F in replacement of LED lamp/bulb 9 watt, bipin with all accessories, complete, all as specified and directed.

S&F and connection of GI pipe of size 25 mm bore dia, medium grade including GI fittings and fixed complete to walls and ceilings or laid in floors, complete, all as specified and directed.

S&F and connection of GI pipe of size 20 mm bore dia, medium grade including GI fittings and fixed complete to walls and ceilings or laid in floors, complete, all as specified and directed.

S&F gun metal gate valve of size 25 mm dia including connection and testing, complete, all as specified and directed.

S&F gun metal gate valve of size 20 mm dia including connection and testing, complete, all as specified and directed.

S & F 20mm bore brass ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

M&L for cutting of existing steel tubing of size 25 mm dia for alterations or additions, done in position without taking down, complete, all as specified and directed. Note: Each cut shall be measured.

Note:- The total shall subject to adjustment of credit of Rs 110567.25 for old Materials as per Schedule of Credit.

H.S. Enterprises

m/s jupiter builders

M/S PAWAN KUMAR NEGI GOVT. CONTRACTOR