Supply of Furnitures Repairing and painting work of Rambagh Dump under zone-4.

Finishing walls with Putty appro roved brand and manufacture and of required shunde on undacorated wall wurface to give even thoude over including curing and cost of all material, labour, T&P etc required for proper completion of work

Finishing walls with exterior emulsion paint (Apex) of approved brand and manufacture and of required shade on undacorated wall surface to give even shade over 1.25 Ltr/10sgm including one cont of primer applid 0.75Ltr/10sqm.coat curing and cost of all material, labour. T&P etc. required for proper completion of work for two coat.

Construction of gramular hase (GSB) by providing course graded material, spreading in uniform layer with mortor grader on prepared surface, mixing by mixin place method with rotovator OMC and compacting with viberatory roller to achieve the desired density as per clause 401.

Providing & laying of Rubber moudded Interlocking Concrete block pavement with 80mm thick CBP (75% Gray & 25% Red/Yellow colored) having strength not less than 30KN/SOM complete as per technical specification Clause 1500

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level 1:6:12 (1 cement: 6 coarse sand (zone-iii): 12 graded Brick aggregate 40mm (nominal size)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorbtion less than 0.08% and conforming to IS 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigements etc. complete. Size of tile 600x600mm

Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete Marble tiles (polished) Raj Nagar 8 mm thick

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, Including all CPVC plain & brass threaded fittings, Ve fixing the pipe with clamps at 1.00 mm spacing. This includes Jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting 25 mm nominal outer dia Pipes

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main "T" runner sheet, spaced at 1200 mm center to center and cross "T" sheet, 1200 mm long spaced between main "T" at 600 secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T runners to be suspended from celling using Gl slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm Gl adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T bottom exposed width of 24 mm of all T- sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. Gi Metal Celling Lay in plain Tegular edge Global white color tiles of size 595-595 mm, and 0.5 mm thick with 8 mm drop: made of Gl sheet having galvanizing of 100 gms/sqm (both sides

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle Iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces