8826 E8

Amount

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

Dismantling of brick work /stone bouldersbuilt in cement mortar including all quins, arches, pillars etc complete all as specified and as directed.

Chipping, removing carefully loose/damaged concrete incl plastering from RCC surfaces of columns, beams, soffits of slabs etc by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land, complete all as specified and directed. Note: Hard concrete shall not be removed by force.

Demolition cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) .

Demolition of stone slabs and tiles laid beded and pointed in any mortar of any description or thicknes in floors,walls, aprons etc, complete all as specified and directed.

Dismantling boarding any description fixed in any position with nails, complete all as specified and directed .

Demolition of lime concrete or lean concrete from sunken floor including floor tiles, hacking of surfaces after cleaning with wire brush (floor and adjoining walls) and disposing off debris outside MD land, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 15mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 20mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 25mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 40mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 50mm bore, complete all as specified and directed.

Dismantling of 100mm dia cast iron or reinforced concrete drain pipes,jointed in cement mortar and taking out of trenches if required drain pipes, complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) Sqm but not exc 1.5 Sqm each including complete all as specified and directed.

Taking down shutter of any description, exceeding 1.0 square Metre and not exceeding 2.0 Square Metre each, complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4.0 Sqm each including complete all as specified and directed.

Taking down existing aluminium joinery of any description (frame/ shutters) with all fittings (but excluding grills) complete all as specified and directed.

Taking down existing aluminium grills from balcony/ any locations complete all as specified and directed.

Demolition of brick/cement concrete (unreinforced) / pcc tiles from existing roof/terrace etc and also removing/taking down of existing water proofing treatment of any thickness in any position including cleaning the surfaces of roof etc with wire brush complete and removing the retreived debris out side MD land, all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc, complete all as specified and directed.

M&L for PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in hold fast, bed plate etc including necessary form work complete all as specified and as directed.

M&L for PCC (1:2:4) type B-0, using 12.5mm graded stone aggregate as in leveling course over RCC roof surface to achieve required slope, benching etc including making rounded or chamfered on edges mixed with WPC as per manufacturer's instructions, complete all as specified and directed.

M & L for filling of lean concrete 1:5:10 type E2 (using 40 mm graded stone aggregates ) in sunken portion, as per requirement complete all as specified and directed.

M&L for PCC 1:2:4, type-B, using 20mm graded stone aggregated as in sub base of floors and for any other propose in any location mixed with WPC @ 2% by weight of cement, complete all as specified and directed. Note: Supply only WPC will be measured and paid separately.

M & L for Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 meter mean radius built CM 1:4 complete all as specified.

S&F 18/19 mm thick prelaminated partcile board both sides , interior grade , of approved shade and pattern fixed with screws to timber frame for cupboard and shelves and all necessary fittings ( hinges , scrowes , beeding piece haspstaple ), complete all as specified

M & L for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages : Stage 1: Providing 15mm thick plaster in CM 1:3 mixed with water proofing chemical of Dr.Fixit or Shalicrete 'R' of STP Ltd in the proportion/quantity all as per manufacturer's instructions. State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces. Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer's instructions. Stage 4: Laying fyber glass cloth (weight not less than 50 gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 5: After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 6: Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer's instructions. Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES :(i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid . (ii) The above treatment shall be got executed through applicator of manufacturer and necessary authenticated documents on account of above shall also be produced by the contractor.

Supply and fixing of 20 mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings (including provision of special fittings i.e. brass elbow, brass tee, Male brass threaded adaptor, female brass threaded adaptor etc required for fixing of bib tap, stop valve with CPVC pipes) concealed in walls/ ceiling or laying in floors etc., also including cutting chases, grooves and making good the same in CM 1:3 after fixing of pipes / fittings, complete all as specified and directed.

M&L for 15 mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing surfaces even and smooth complete all as specified and directed Make: Easy Plast from M/s wall plast or chemplast or readyplast from Ultratech” Note: (i) The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with ready mix plaster and nothing extra shall be payable on this account. (ii) This item shall be operated only for the locations where the thickness of existing adjoining plaster is to be matched

Taking down carefully existing aluminium sliding window shutters, taking down of existing broken 5 mm thick plain sheet glass from aluminium sliding window shutters including existing rubber gasket complete, supply and fixing 5 mm thick plain sheet glass with and including provision of new rubber gasket and re-fixing the shutters in existing position, complete all as specified and directed.

Taking down carefully existing aluminium sliding window shutters, taking down of existing stainless steel wire mesh from aluminium sliding window shutters including existing rubber gasket complete, supply and fixing stainless steel wire mesh of dia 0.36 mm and average width of aperture 1.40 mm with and including provision of "U" clip, re-fixing the shutters in existing position, complete all as specified and directed.

Taking down carefully aluminium sliding window shutters from the frames or chowkhat and supply and fix New locking arrangement in place of old one and re-fixing the same shuters in existing position etc, complete all as specified and directed

S&F 4 mm thick sheet glass , figured glass, pinhead type , glazing with oil putty area not exceeding 0.50 Square Metre each pane complete all as specified and as directed.

S& F second class hard wood plain, solid straight chowkhats and frame, wrought framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good disturbed surfaces of wall complete all as specified and directed

S&F for factory made 35 mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides and fit, complete all as specified and directed.

S&F Factory made Plain framed, panelled shutters, 35 mm thick of second class hard wood (Hollock) (any numbers of panels) with panels of 12 mm thick veneered particle board exterior grade medium density with commercial veneering on both faces with sheesham wood beading all round the panel made out of 20 by 15 mm , on one side and fitted to chowkhats complete all as specified and as directed.

S&F factory made Glazed and skelton shutters, 35 mm thick of Second class hard wood open rebated and prepared to receive glass, gauge etc without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) )complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm mm nominal dial of wire and average width or aperture 1.40mm for fixing to wooden door/ window shutters in any position with new beads/ steel section painting to match with existing complete all as specified and as directed.

S&F stainless steel wire in repairs cloth 0.36 mm mm nominal dial of wire and average width or aperture 1.40 mm for fixing to wooden door/ window shutters in any position with new beads/ steel section as required for securing including dismantling of old jalli and painting to match with existing complete all as specified and as directed

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with Square tube, supply and fixing in opening as per specification given under SSR Part II 2010 including making good the disturbed surface all as specified and directed. Make: SYNTEX/SHALIMAR/RAJSHRI

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2010 complete all as specified and directed. Make : SYNTEX/SHALIMAR/RAJSHRI

S&F Factory made solid PVC moulded Door Shutter 30 mm thick (style) with 2, 4, 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm prelam PVC sheet on back face as per specification & drawing for Sl No. 8103 on ser page No. 161 in SSR-2010 (Part-II), complete all as specified and directed.

M&L for treating with tar or coal tar black paint on back of chowkats area exc 0.10 Sqm but not exc 0.5 Sqm each complete all as specified.

M&L for treating with tar or coal tar black paint on back of chowkats, ends of posts, holdfasts etc. area not exc 0.1 Sqm each complete all as specified.

S&F 100 mm long stainless steel butt hinges fixed with stainless screw complete all as specified and as directed

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length, complete all as specified and directed

S&F aluminum anodised barrel tower bolts of extruded section of size 200 mm length, complete all as specified and directed

S&F 150 mm extruded aluminum alloy handles, fabricated type anodised, complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 250 mm complete all as specified and as directed.

S&F D-handle of size 96mm long of stainless steel with matt or gloss finish for modular kitchen shutters, complete all as specified and directed.

S&F continuous (piano) hinges, width of flap 30mm (when open), mild steel, bright finish or electro-galvanised, complete all as specified and directed.

S&F Brass 60mm Economy pin cylindrical lock (one side knob/one side key), make : Godrej or equivalent as approved by the GE.

S&F standard aluminium section powder coated (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by GE ) as in frame, shutters for doors, window / ventilators, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed (Aluminium section shall be of make Jindal/Hindalco/ Indalco) Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, shall be measured and paid separately as supply only under respective item.

Supply only 5 mm thick sheet glass, ordinary quality fixed in aluminium window along F section all as specified and directed

Supply only Stainless steel wire cloth.0.36mm nominal dia of wireand average width of aperture 1.40mm and fixed with stainless steel wire staples in aluminium windows or along with 'F' section, complete all as directed by EIC.

S&F aluminium anodised Grills of approved design for window / ventilators and fixing with F/U channel including drilling as required in RCC sections in rectangular or architectual type balcony opening in existing building, complete all as specified and directed. Note: The Grills shall be of Model DG-100/DG-102 of Make Deco or equivalent make as approved by the GE.

M&L for 35 to 40 mm thick machine cut, prepolished cuddappa stone slab as in plateform for fixing oval shape wash hand basin(including cutting the slab to oval shape to accomdate the sink and WHB), pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab etc,also including moulding/rounding to edges of the slab, complete as specified and directed.

M&L for 20 to 25 mm thick machine cut pre-prolished cuddappa stone Slabs (table rubbed and polished) as in cills, jambs etc, pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab etc, including moulding/rounding to edges of the slab and also including provision of 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for prepolished machine cut kota stone slab flooring 20-25 mm thick over 20 mm thick cement screed base CM 1;6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations, complete all as specified and directed.

M&L for machine cut kota stone prepolished slab flooring 20-25mm thick as in flooring, treads, risers, landing etc over 15mm thick cement screed base CM 1;6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

M&L for Durastone Heavy Duty vitrified tiles (300x 300) x 10-12 mm thick in floor set and jointed with neat cement slurry and pointed in coloured cement to match over screed bed or bedding layer of morar 20 mm in cement mortar 1:6 complete all as specified.

M&L for coloured Non-skid ceramic tiles 7 to 8mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15 mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

All as per items No 64 above but in skirting or in dado including 10 mm thick rendering CM 1:4 complete all as specified and directed

M&L for coloured glazed ceramic tiles 300x200x6 to 7 mm thick set and jointed in neat cement slurry and pointed with coloured cement as in skirting/dados including 10mm thick rendering in CM 1:4 as in backing coats of tiles finished the surfaces rough to receive tiles etc complete all as directed and specified.

M&L for non skid coloured ceramic tiles 300x300x6 to7mm thick in floors etc set and jointed in neat cement slurry and pointed with coloured cement to match the shade complete including 15 mm thick CM 1:6 screed bed for laying floor finishes all as specified and directed..

S&F Vitrified light shade ceramic tiles 10 mm thick (square/rectanglar) polished area of each tile not exceeding 0.36 sqm ,in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to matched laid over 15mm thick bedding layer of CM 1:6 complete all as specified and as directed.

Al as per item No 68.0 but as in skirting /dado laid over 10 mm thick bedding layer of CM 1:4 complete all as specified and as directed

M&L for coloured 300x600x7 to 8 mm thick digital ceramic tiles on vertical surfaces such as skirting,dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:4 etc, complete all as specified and directed.

M&L for coloured 450x350x7 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:4, complete all as specified and directed.

M&L for coloured Non-skid digital ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15 mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directe.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75 mm thick, with expansion joints at 3.0 m center to center & top surface finished even and smooth without using extra cement etc complete all as specified and directed.

M&L cement plaster (1:3) with 10 mm thick to be finished smooth without using extra cement mixed with WPC @3% by weight of cement, , complete all as specified and directed.Note : WPC shall be measured and paid separately as supply only.

Supply only lquid water proofing compound, complete all as specified and directed.

Material and labour 75 mm thick PCC 1:4:8 type D-2 using 40 mm graded aggregate as in floor complete all as specified and as directed..

M&L for 25 mm thick prepolished PCC chequred tiles size 30x30 CM jointed with over and including cement mortar 15 mm thick in CM 1:4 screed bed complete all as specified and as directed.

M& L for rendering 10 mm thick with ready mix plaster on ceiling surface finished even & smooth with sagol finish complete all as specified.

M&L for 20 mm thick (12 mm +08 mm ) in two layers ( with top 08 mm thick using WPC as per manufacturers instructions ) polymer modified ready mix cement based plaster on the wall surfaces including finishing the surfaces even and smooth, complete all as specified and directed. Make:Easy plast from M/s wall plast or chemplast or readyplast from ultratech.note:the thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with the readi mix plaster and nothing extra shall be payable on this account.

M&L for cleaning existing reinforcement by sand blasting with suitable pump as directed by the GE and wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.)

M&L for Anticorrosive Treatment to Reinforcement Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed

M&L for providing mild steel TMT bars in various structural RCC elements like column, beams and Slab etc. including cutting, bending, fixing the bars, tying with binding wires etc. complete all as specified and directed. Note: This item is applicable for additional bars required in the existing RCC structures.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit, upto 20mm thickness including levelling, profiling etc complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed.

M&L for leakage / seepage proof coating consisting of preparing the new/old surfaces of existing exterior walls, parapet walls, chajjas etc. and applying Primeseal primer of M/s Dr Fixit or equivalent chemical of M/s STP Ltd as approved by the GE or one coat of Chemstic PDE 600 elastomeric coating (and allowing to dry for 8hrs) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of M/s Dr Fixit with DFT 100microns or Shalicryl 215 of M/s STP Ltd or Chemstic PDE 600 elastomeric coating (the surfaces after painting one coat shall be allowed to dry for 6 to 8hours before application of next coat) including necessary scaffolding etc complete all as per manufacturer instructions and all as specified & directed. Note work to be carriedout by authorised approved applicator

M&L for preparation of newly plaster/concrete surface of wall and applying two coat of distemper oil emulsion on walls with one coat of primer ( chalk white on plastered surfaces) complete all as specified and directed

M& L for preparation of newly plastered surface of Ceiling and applying Three coat of white wash complete all as specified and directed

M & L for preparing old decorated surfaces of wall (plastered or unplastered or previously white washed ) & applying one coat of white wash complete all as specified

M& L for preparation of old plastered surface of ceiling and applying one coat of white wash complete all as specified and directed

M& L for complete removal of existing treatment on surfaces of walls and applying two coats of oil bound distemper over chalk whiting including 3 mm thick wall care putty applying on walls for smooth finish complete all as specified & directed by EI C.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc by meachincal means complete all as specified and directed

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, or in any location and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. over screed bed or bedding layer of mortar 15 mm in cement mortar 1:4set and jointed complete all as specified and directed

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160 gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm and miniumun thickness 4mm . (ii) Non woven polyester weight not less than 160 gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (d) applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane for non accessible roof complete all as specified and directed.

M& L cement cocreat tiles of size 250x250x22 mm machine made, pressed laid over & including cement mortar screed 15 mm thick in CM 1:4 jointed in neat cement sullary and pointed with epoxy joint filler of approved complete all as specified and directed.

S&F mild steel Framed work such as grills, gratings etc, with ends of bars shouldered or rebated or forged into spikes, framed guard bars, barred iron doors, railings, framework of water tanks and similar work conforming to Fe -290 Grade -E-165, complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates,rails braces etc complete drilled for fixing of steel sheeting or other covering doors etc complete all as specified.

M&L for two coat of synthetic enamel paint over one coat of red oxide primer including preparation of new steel surface complete all as specified.

M& L for preparation surfaces of new or previously untreated wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats synthetic enamel paint over one coat of pink primer complete all as specified and as directed

S&F Wall Mixer with provision for overhead shower with 115 mm long bend pipe on upper side, connecting legs & wall flanges, complete all as specified and directed, Make- Jaquar Cat No- FUS-29273UP or equivalent of Marc/ Kohler as approved by the GE.

S&F Sink Mixer with Swinging Casted Spout (Wall Mounted Model) with connecting legs & wall Flanges, complete all as specified and directed, Make- Jaquar Cat No-CON-309K or equivalent of Marc/Kohler all as approved by the GE.

S&F stainless steel electro polish of grade 202 as in kitchen trolley for modular kitchen consisting of cutlery cup / soucer, thali basket, drawers, plain basket, bottle pullout basket etc, complete all as specified and directed. Note : The design and specifications of the above item (including of the materials) shall be got approved by the contractor from the GE before procurement.

M&L for 18/19 mm thick marine ply bonded with undiluted Phenol Formaldehyde resin, Boiled Water Proof, Specific gravity 0.80 (minimum), moisture content 8-12%, water absorption <5%, provided with and including 1mm thick plastic laminated sheet on both sides of plywood (plastic laminated sheet shall be with decorative choice lamination on one side and other side balancing) (Make of ply : Anchor, Kitply, Century Ply, Green Ply) as in kitchen cabinets, cub board, shelves etc, Fixed with screws to frame work, complete all as specified and directed, Note: Payment for glass panels shall be made for separatly as "supply only".

S&F 310X 450 MM SIZE PVC cabinet mirror of Make prayag polymer pvt Ltd Cat No :551 or eqivalent make as approved by GE complete all as specified and as directed

S& F in repairs tubular towel rail brass chromium plated curtain rod 20 mm dia complete all as specified and directed

S& F in repairs brass chromium plated 20 mm dia brackts complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls all complete all as specified and directed.

All as per item no. 107.00 above, but 75mm bore

S&F Vitreous china squatting pan orissa pattern of size 580 x 440mm with integral foot rest and 'P' or 'S' trap including lime concrete bedding connecting flushing pipe and taking out old WC pan & lime concrete and unserviceable connections and making good for floor etc complete all as specified and as directed

Removing plant/growth including its roots upto 1.00m of plant height at any location/at any storey and of any description and treating the surfaces with Acid (HCL) and making good surfaces with cement mortar 1:4, complete all as specified and directed.

Supply & fix 20mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Supply & fix 25mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Supply & fix 40mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Supply & fix 50mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F cast iron Nahani trap 100mm dia out let including grating connecting jointing to waste pipe with lead jointing and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces (including removing existing trap) complete all as specified and as directed .

S&F PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F towel rail 600 mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms) Make Prayag Cat No BA -01 or euivalent make as approved complete all as specified and directed.

S&F in repairs high level/low level PVC flushing cistern with PVC flush pipe, brackets, and PVC connection complete of 10 Ltr capacity.

S&F in repairs bib taps, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated Make ESSCO Cat No MQT-511 or equivalent make as approved complete all as specified and directed..

S&F in repairs bib taps, fancy type, long body with wall flange, screwed for iron pipe or for brass ferrule 15mm bore , Make Jaquar Code No CON-107KN or equivalent of make KOHLER or MARC as approved by the GE, complete all as specified and directed.

S&F in repairs bib taps two way cock, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated Make ESSCO Cat No MQT-512 -A or equivalent make as approved complete all as specified and directed..

S&F Toilet roll holder with flap complete all as specified and directed, Make : Jaquar Cat No-AKP-35753P or equivalent of make KOHLER or MARC as approve by the GE.

S&F in repairs pillar taps; of cast copper alloy with capstan; head chromium plated screwed down end with pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe& fixed Make ESSCO Cat No COSS ESS-103001 or equivalent make as approved complete all as specified

S&F Angular stop cock with wall flange, fancy type, Make Jaquar Code No FUS-29053 or equivalent of make KOHLER or MARC as approved by the GE for iron pipe of 15mm bore, complete all as specified and directed.

S&F in repairs stop cock cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass chromium plated with fancy shank and cup(concealed type) Make ESSCO Cat No MQT -513 A or equivalent make as approved

S&F CP grating doom 125mm dia of size(including removing existing) complete all as specified and directed.

S&F chromium plated shower rose 125mm size with or without swivel joint for fixing in 15mm dia pipe(including removing existing shower) Make Jaquar or equivalent of make KOHLER or MARC as approved by the GE

S&F Hand Shower (Health faucet) with 1.00 metre long Easy flex tube in chrome finish & wall Hook, Cat No ALD-CHR-565 of JAQUAR or equivalent of make MARC or KOHLER as approved by the GE.

S&F soap dish holder complete all as specified and directed, Make : Jaquar Cat No-CAN1131N or equivalent of make KOHLER or MARC as approved by the GE.

S&F in repairs wash hand basin (550x400mm) vitreous china (flat back or angle back type) any size, including cutting for and pining in ends of brackets or erecting stand but exclusive of fixing and supply of waste pipe complete all as specified .

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

S&F vitreous china, table top wash hand basin oval shape size( 420x420mm x135 mm) cat No : ARS-WHT-0538 Make of JAQUAR fixed on granite counter top slab including brass chromium plated full threaded waste coupling with grating 32mm dia pvc waste pipe complete all as specified and directed. (Note: Granite slab, RCC plat form, brick wall support etc shall be measured and paid separately)

S&F pillar taps, fancy type for iron pipe of 15mm bore, Make: Jaquar code No CQT-23021 or equivalent of make Kohler or MARC as approved by the GE, complete all as specified and directed.

Vitreous china wash down water closet pan “Pedestal Pattern” white, with seat white closed pattern with flat bottom and cover mild steel chromium plated or aluminium anodized hinging device including flush pipe and joints etc and connection to drain, flushing, pipe, anti-syphonage pipe and fixing arrangements with fixing bolts etc including making good the disturbed portion of floor in cement concrete 1:2:4 type (B-0, as in repairs, complete all as specified and directed. (MAKE : Neycer Keramag (Standard), Hindustan Sanitary ware (Hind ware First quality), Parry ware (super fine), Cera (First quality)

Disconnecting existing water upto 1000 liter storage tanks, setting aside (or lowering if required) for repairs to roof below, and replacing (or hoisting if required), re-fixing in position and re-connecting on completion of roof work complete all as specified and directed by the Engineer-in-charge

S&F bands, straps , supports or stays for rain water, ventilating pipes including bolts, clamps, hold fasts etc and similar small articles to Fe-410-0 or Fe-310-0 all as specified & directed.

S&F 110 mm bore PVC (SWR) branch piece single (Single Y ) equal or unequal complete all as specified and as directed

All as per item No 137.00 above but 110 mm dia bend complete all as specified and as directed

S &F PVC (SWR) branch piece,single(single Y) 75mm bore equal or unequal complete all as specified and as directed

S &F PVC (SWR) bends, 75mm bore, any radius complete all as specified and as directed

S &F PVC (SWR) junction single(single T), 110 mm bore, equal or unequal complete all as specified and as directed

S &F PVC (SWR) junction single(single T), 75 mm bore, equal or unequal complete all as specified and as directed

S &F PVC (SWR) branch piece,double( double Y) 75mm bore equal or unequal complete all as specified and as directed

S &F PVC (SWR) branch piece,double (double Y) 110 mm bore equal or unequal complete all as specified and as directed

&F for refixing the shutter in same/other opening of any description exc 1.0 Sqm& n exc 2.00 sqm complete all as specified and as directed

S&Frolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates fe 410 gde

M&L for providing 4mm thick FRP chajja of approved pattern/shape/size (with sides & front drop etc), colour/pattern as of mangalore clay tile (the frpchajja shall be moulded in gel coat finish, the thickness shall be 4 mm and back patti to be additionally reinforced with core matt, all resins and pigment shall be fully weatherable and uv established, core malt shall be used with gsm for extra thickness, necessary frp covered metal, chajja shall be fixed in position with and including 8mm dia and 125mm long split fastener bolts (shakti make or equivalent make as approved by the ge) spaced not more than 45cm c/c and also filling the gaps with polysulphide sealant including necessary scaffolding/erection of work platform etc, complete all as specified and directed. Make: M/s titan enterprises or advance FRP or Sintex.

S&F pre-painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50 mm of an colour having tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self-tapping screws as specified

M&L for providing and injecting chemical emulsion for post constructional anti-termite treatment along external wall where the apron is nor provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete

M&L for providing at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ .5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same

M&L for casting & repairing of excessively damaged distressed RCC members (exceeding 60mm in thickness) with prebatched, prepacked, single component ready to use micro concrete from Fosroc (Renderoc RG) or equivalent of Dr. Fixit as approved by GE, at any level/ height and at any lead or lift as directed including prefabricated water tight formwork, centering, scaffolding, also including mixing , laying, leveling, finishing, curing etc as per manufacturer's specifications and all other relevant works, complete all as specified and directed. (Note: Reinforcement only shall be measured and paid separately)

M & L for roof treatment with heavy duty, reinforced heat insulative acrylic polymer modified liquid membrane of Shalicryl LH HI of STP Ltd or Sika topseal-109 HI of Sika India Ltd or equivalent over a coat of primer of same brand including preparation on old surface.( For non-accessible roof) Note : - (i) Application will be done with authorized applicator of respective company only. (ii) Mixing & rate of application will be strictly as per manufacturer instruction only. (iii) A guarantee of 05 years will be given by the company for the product & applicator for the no leakage/seepage condition

Taking down copper/ aluminum point wiring (Light/Fan/Socket or power) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, socket, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces to walls floors etc.

Taking down complete main switches/DBs with enclosure and its components of any size and capacity ,etc complete all as specified and directed.

Taking down ceiling fan/exhaust fan, sealing cable end dismantling blades and removing fan and blades and keeping in safe custody for refixing at site, complete all as specified and directed.

Taking down old US sub main wiring of size 4 Sqmm/2.5 Sqmm From wall/ceiling/rooof etc complete all as specified and directed.

Taking down of Old LT Panel includig disconnecting of cables from panel etc complete all as specified and directed

Dismantling and taking down fluorescent tube light single/double of any wattage or size street light fittings for repair or replacement of burnt/worn out accessories or carrying to MES store to issue under credit complete all as specified and directed

Taking down of old earthing materials etc complete all as specified and directed.

M & L for point wiring complete with proper colour coding using, 1100 Volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked drawn in and including PVC casing caping (minimum 25mm width) fixed on the surfaces of wall, ceiling etc with all accessories, fittings, PVC junction boxes etc, sunk pressed steel boxes not less than 2 mm thick, 50 mm deep terminal boxes covered with 3mm thick plastic laminated sheet top cover fastended with chromium plated brass screws, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed for one light point /fan/bell point controlled by one one way switch, complete all as specified and directed. Note : Rates included for cutting as required at site without any damage and making good in CM 1:4 and matching the surface as required .2 all screws and washer for point wiring shall be Stainless steel . Nothing is extra shall be admiisible on this account

Description all as per item No. 160.0 above but for One 2pin/3 pin socket outlet 5 Amps on same board complete all as specified and directed.

Description all as per item No. 160.0 above but for One 2pin/3 pin socket outlet 5 Amps on independent boardcomplete all as specified and directed.

M&L for point wiring using proper colour coding with 1100 Volts grade, 2.5 Sqmm PVC insulated, FRLS, unsheathed, wire confirming to IS-694, Part-II, ISI marked with multistranded copper conductor drawn in and including PVC casing caping (minimum 25mm in width) fixed on the surfaces with all accessories, fittings, PVC junction boxes etc, sunk pressed steel terminal boxes not less than 2 mm thick, 50 mm deep, covered with 3 mm thick plastic laminated sheet top cover fastened with chromium plated brass screws, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, multistranded, copper conductor 1100 Volts grade, green color, continuous earth wire connected to common earth dolly for 15 Amps, 3 Pin, socket outlet independent, complete all as specified and directed. Note : rates included for any cutting as required at site and making good in CM 1:4 and matching the surface as required

S&F Switch Piano 5 Amps, 250 Volts, one way, flush type, complete all as specified and directed.

Supply & Fix Bell push, flush type, 5 Amp, 230 Volts, complete all as specified and directed.

S&F Switch Socket combination 2 in 1 , 5 Amps, flush type, 5 Pin, 240 Volts, complete all as specified and directed.

S&F Switch Socket combination 2 in 1 , 5/15 Amps, flush type, 6 Pin, complete all as specified and directed.

S&F ceiling rose three terminal, 230 Volts PVC / Polyucarbonate body, complete all as specified and directed.

S&F fan regulator, electronic stepped (5 step), 230 volts, 100 watt, flush type and connecting-up, complete all as specified and directed.

Supply and fix bell dig dong, AC, 230 V, single pole, complete all as specified and directed.

M&L for point wiring using proper colour coding with 1100 Volts grade, 1.5 Sqmm PVC insulated, FRLS, unsheathed, wire confirming to IS-694, Part-II, ISI marked with multistranded copper conductor drawn in and including PVC concealed conduit of suitable size of wall/ RCC slab/ ceiling/ colunms/ beams etc with all accessories, fittings, PVC junction boxes etc, including provision of modular metal flush boxes with modular cover plate and frame suitable for mounting modular switches, sockets, fan regulators etc, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multistranded copper conductor green color as continuous earth wire connected to common earth dolly all as specified and directed for one light point/ fan/bell point controlled by one one way switch, complete all as specified and directed. Note : rates included for concealed cutting as required at site and making good in CM 1:4 and matching the surface as required Note : Rates included for concealed cutting as required at site without any damage and making good in CM 1:4 and matching the surface as required .2 all screws and washer for point wiring shall be Stainless steel . Nothing is extra shall be admiisible on this account

Description all as per item No. 171.0 above but for One 2pin/3 pin socket outlet 5 Amps on same board complete all as specified and directed.

Description all as per item No. 163 above but for One 2pin/3 pin socket outlet 5 Amps on independent boardcomplete all as specified and directed.

M&L for point wiring using proper colour coding with 1100 Volts grade, 2.5 Sqmm PVC insulated, FRLS, unsheathed, wire confirming to IS-694, Part-II, ISI marked with multistranded copper conductor drawn in and including PVC concealed conduit of suitable size of wall/ RCC slab/ ceiling/ colunms/ beams etc with all accessories, fittings, PVC junction boxes etc, including provision of modular metal flush boxes with modular cover plate and frame suitable for mounting modular switches, sockets etc, also including 2.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multistranded copper conductor green color as continuous earth wire connected to common earth dolly for 15 Amps, 3 Pin, socket outlet independent, complete all as specified and directed. Note : Rates included for concealed cutting as required at site without any damage and making good in CM 1:4 and matching the surface as required .2 all screws and washer for point wiring shall be Stainles steel . Nothing is extra shall be admiisible on this account.

Supply & Fixing modular type one way switch 6 Amps, 1 module, complete all as specified and directed.

Supply & Fixing modular type bell push switch, 6 Amps, 1 way, 1 module, complete all as specified and directed.

Supply & Fixing modular socket 5 Amps, 5 Pin, 2 module, complete all as specified and directed.

Supply & Fixing modular socket 5/16 Amps, 6 Pin, 2 module, complete all as specified and directed.

Supply & fixing modular type one way switch 16 Amps, 1 module, complete all as specified and directed.

Supply & Fixing step type, modular fan regulator, 100 W, 2 module, complete all as specified and directed.

S&F Retro LED tube rod 20 Watts, 230 volts, with high efficency PMMA diffuser, the rod shall be of Cat No. LTT8-20 of Crompton or Equivalent from Philips/Bajaj as approved by the GE, complete all as specified and directed.

S&F decorative box type LED light fitting, prewired complete with all accessories/inbuilt fittings, suitable for Retro LED tube rod 20 Watts, 230 volts, including PVC Square blocks 2 Nos for mounting the fitting, provision of three core copper conductor cable to connect from ceiling nose to light fitting, the fitting shall be of Cat No. IGP131LT8-16 of Crompton or equivalent from philips/Bajaj as approved by the GE. Note: Retro LED Light tube rod 20 Watt shall be paid separately under respective item

S&F Retro LED tube rod 08 Watts, 230 volts, with high efficency PMMA diffuser, the rod shall be of Cat No. LTT8-8 of Crompton or Equivalent from Philips/Bajaj as approved by the GE, complete all as specified and directed.

S&F decorative box type LED light fitting, prewired complete with all accessories/inbuilt fittings, suitable for Retro LED rod 08 Watts, 230 volts, including PVC Square blocks 2 Nos for mounting the fitting, provision of three core copper conductor cable to connect from ceiling rose to light fitting, the fitting shall be of Cat No DMLN1LT8-8 of Crompton or equivalent from philips/Bajaj as approved by the GE. Note: Retro LED Light tube rod 8 Watt shall be paid separately under respective item

M & L for Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan after preparation of surfaces, complete all as specified and directed

S & F MCB DB, 12 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections, complete all as specified and directed. Note: Quoted rate shall also be deemed to include for provision of copper bus bar of 200 Amps rating.

S & F MCB, SP, 05 to 32 Amps, 240 Volts, 10 KA Breaking capacity, C-series, complete all as specified and directed.

M&L for MCB SPN, 240 volt, 40 Amps, 10 KA Breaking capacity, C-series, complete all as specified and directed.

S&F single pole and neutral enclosure with a two pin and earth and metal clad plug socket complete with one single pole MCB 20 Amp 240 Volts complete all as specified including concealing in wall and directed. The Enclosure Shall be Indoasain or Equivalent from Bajaj/Philips

Taking down and refixing of geyser of any capacity including electrical and water supply connections complete with testing

Supply & laying in repair PVC insulated heavy duty ,1100 volt grade electric LT UG armoured cable with multi stranded copper conductor of size 6 sqmm 2 core, saddling the cable in duct/wall etc and making all connection , complete all as specified and directed . Note :- unless otherwise directed, the cable shall be in single piece

M&L for sub main wiring with two single core 4.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 4 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed Note : Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L for sub main wiring with two single core 2.5 Sqmm PVC insulated FR multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 2.5 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed Note : Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

Fixing only Exhaust fan and connecting up including provision of cable from ceiling rose/ connector to fan including Painting of exhaust fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc

Supply and fix in replacement street light fittings in street light poles/Buildings the fitting shall be of LED type 45 Watts complete with and including drivers, pressure die cast aluminium housing, prewired complete. The fitting shalll conform to cat No - LSTS-45-CDL-1 of Crompton greaves or Equivalent from Philips/Bajaj

Supply install, test and commissioning of Powder coated LT Feeder panel cubical in door type panel board compartmentalized in construction all of CPRI approved factory fabricated made out of 2 mm thick CRCA sheet & suitable size to accomodate all accessories / fittings, to accommodate incoming MCCB and TPN Copper bus bars, incomer MCCB and outgoing MCCB, MCB, Contactors The TPN bus bars shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on DMC/epoxy insulator. The bus bar shall have copper extension links for connecting with out going MCCB. The cubicle shall have a bottom channel & free standing frame made of angle iron of size not less than 40mm X 40mm X 6mm, complete all as specified and directed. a) Copper bus bar 400 Amps for 3 phase and Neutral b) MCCB TP 125 Amps 415 Volt 16 KA - 1 Nos c) MCB TPN 40 Amps, 10 KA 415 Volts- 1 Nos d) MCB SPN 40 Amps, 10 KA 230 Volts - 10 Nos e) Space for Fixing 09 Nos of Single Phase Energy Meter of Capacity 40 Amps, f) RYB Indicators - 1 Set

M&L for new earthing complete with galvanised earth plate electode 600 x 600 x 6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level, connected to and including galvanised earth strip 32mm X 6mm to the extent upto 7.5 metre as earth lead by means of bolts, nuts etc, with provision of charcoal and salt all as per electrical plate No 3 of SSR Part I, including water arrangement with GI pipe 20mm bore (medium grade), earth lead protection pipe 40mm bore light grade with bends, elbow etc. from earth plate to test point, excavation and earth work, returning, filling, ramming and removing of soil to a distance not exc 50 metre, making PCC 1:2:4 type B-1 pit (Earth chamber) with RCC 1:2:4 cover 50mm thick reinforced with XPM and testing on completion including making test point on wall as per SSR specifications all as specified and directed. (Note: Cost of GI strip 32mm X 6 mm and protection pipe upto 7.5 metre shall also be deemed to be included in the quoted rate)

Star Construction Co.

M/s Shreeji Construction Co

Garima Construction Co

Parmatma Enterprises

Idustrial products India