boot ankle textile jungle boot direct moulded pu sole in pairs Boot Ankle Textile Jungle Boot Direct Moulded Pu Sole In Pairs ( 2524 ) Technical Specifications Specification Specification Name Values Allowed Values specification Governing Specification Conforming to FDDI (FOOTWEAR DESIGN & DEVELOPMENT INSTITUTE

boot ankle textile jungle boot direct moulded pu sole in pairs Boot Ankle Textile Jungle Boot Direct Moulded Pu Sole In Pairs ( 2524 ) Technical Specifications Specification Specification Name Values Allowed Values specification Governing Specification Conforming to FDDI (FOOTWEAR DESIGN & DEVELOPMENT INSTITUTE

A - 10/A

Sector-24

NOIDA) Specification No. FDDI/SPEC/Jungle Boot/08:2014 (Revised)

approved by MHA vide their letter N o-U.II-98(Spec)/2012-13 -Prov-9775 dated 10/12/2014

and as per following technical requirements - SIZE Size Assorted sizes (5

6

7

8

9

10

11 & 12) as per buyer's requirements 5

11

12

Asso rted sizes (5

11 & 12) as per buyer's requirements COLOUR Colour Olive Green Olive Green

Brown

Blac k

Disruptive Colour of Sole and Toe Cap Black ( For all other Boots) - MATERIALS Upper Material Upper shell consist of Polyester viscose fabric

Water Repellent - 1/5 as an outer layer and 100 % non-woven Nylon (cambrille type) lining as an inner layer. The two fabrics shall be adhered together with flexible adhesive and polyurethane foam of 5 mm thickness. Blend Composition of polyester viscose fabric water repellent Polyester-80% Viscose- Remainder - Binding material of Polyester blended fabric

black having blend composition of Polyester-67%

Cotton-33% & confirming to IS:15852-2009 for colour fastness to light

washing & pH value YES - Insocks Covered with cambrille type non woven material black - Thermoplastic Toe Puff and Counter Stiffner Thickness when extacted from boot shall be 1.7 mm to 1.9 mm YES - Full Chrome Leather for Toe Cap and Arch piece confirming to IS 5677-1986 for Heat resistance

Colour fastness to rubbing crocking

Solvent extractable substances

water soluble matters

Chromium contents & pH value of water soluble YES - Thickness of Full Chrome Leather for Toe Cap and Arch Piece shall be 1.2 mm to 1.8 mm YES - Length of Nylon Laces (cm) 160 - Width of Laces (mm) 6 - 2/5 Breaking Load of Laces ( 20 cm between grips ) (Test Method- IS: 1969) 750 - Mass per 10 pairs of Laces (g) 125 - Dye Fastness to Washing for Laces shall be above 4 (Test Method- IS/ISO 105-C10: 2006) (Test Condition as per table-2

Test Number- C(3)) YES - Dye Fastness to Light (Test Method- IS: 2454) for Laces shall be above 4. YES - pH Value of aqueous extract shall be 6.5 to 8.5 for Laces YES - Sewing threads Polyester Sewing thread confirming to IS 9543-1980 (Variety No- 7) - OTHER REQUIREMENTS Mass per pair for Size-8 shall be 750 to 850 gms (with increase or decrease of 50 grams for each bigger and smaller size respectively) YES - Leg height for Size-8 shall be 160 mm (with increase or decrease of 2 mm for each bigger and smaller size respectively) YES - SOLE Sole Direct Moulded Polyurethane - Minimum thickness of sole (mm) 4 - Cleat height (mm) 2.5 - Thickness of sole when measured at forepart from outside with side wall (mm) 20 - Thickness of sole when measured at waist from outside with side wall (mm) 16 - 3/5 Thickness of sole when measured at heel from outside with side wall (mm) 35 - TEST REPORT Availability of Test Report from NABL/ILAC accredited or Central Government Lab to prove conformity of products to the specification. YES - Name of the Lab ITL LABS - Address of The Lab B-283

284

Phase 1

Pocket B

Industrial Area

Mangolpuri

Delhi

110083 - Test Report No. X00702/NMS - Test Report Date 18/04/2018 - Test reports to be furnished to buyer on demand YES - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Vivek Srivastav 490006

THQ IG SPL OPS

BSP Hr Secondary School

Opposite SBI- Maroda Uttai Risali sector

Bhilai 2524 30 Required No ePBG Required No