PROVISION OF ROOM FOR RETINUE AT AFS YELAHANKA AND CONSTRUCTION OF RAMP CONNECTION BETWEEN PRIMARY BLOCK AND NEW BUILDING VIVEKAKANDA BLOCK AT KV AF STN YELAHANKA

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of cables, pipes, foundation for poles etc., and getting out in hard/dense soil all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil all as directed.

Returning filling in excavated soil upto a depth of 30 cm after riddling of excavated soil (in lieu of sand) for cushioning of cable and refilling of trenches with left over normal excavated soil including spreading, leveling, watering and well ramming in layers complete all as specified and as directed by Engr-in-Charge.

Removing excavated material (soil) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all specified and as directed.

Demolition of reinforced concrete in ground floors and pavings n exc 15 cm thickness all as specified and directed.

M&L for Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface all as specified and directed.

M&L hardcore of guage exc 63mm but n exc 100mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rolled/rammed to a true surface in broken stone or boulders all as specified and directed. Note: For payment purpose punned thickness shall be considered for measurement.

M&L for plain cement concrete type D-2,1:4:8 (using 40mm graded stone aggregate) in foundation, filling & mass concrete complete all as specified and as directed.

M&L PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in Coping /benching of manholes including eatherlng,rounded /chemfered angles and throating as directed including necessary form work and finishing all exposed surfaces of concrete even and smooth without using extra cement complete all as specified and as directed.

M&L for precast cement concrete block type C1, 1:3:6 using 20 mm graded aggregate block masonary with solid blocks exc 10cm in width and setting in CM 1:6 all as specified and as directed.

M&L for precast cenment concrete type B1 1:2:4 (20 mm graded agg) block masonary with solid blocks exc 10cm in width and setting in CM 1:6 complete all as specified and directed.

M&L for Precast RCC cover slabs for manholes 1:2:4,type B1, (using 20mm graded stone aggregates), set in CM 1:4 including necessary form work and finishing the exposed surfaces of concrete even and smooth without using extra cement complete all as specified all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. and concrete surfaces finished rough & flat complete all as specified and directed.

S&F Second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed all as specified and as directed.

S&F 35mm thick Second class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc divided into squares,with plain,chamfered or rounded,mitred and rebated sash bars,any numbers.edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a), supplied and fitted to chowkats all as specified and as directed

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet all as specified and directed.

M&L Factory Made Solid PVC Moulded Door Shutter, with particle board core 28 to 30 mm thick (stiles),with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face including neccessary fitiings etc complete as specified and directed.

S&F for aluminium anodised, barrel tower bolt 150mm length of extruded section all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified and directed.

S&F Butt hinges of size 100mm extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type C-21 all as specified and directed.

S&F for aluminium handle 150mm cast type anodised all as specified and directed.

S&F of Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and as directed. Note : Rate quoted by the contractor is inclusive of rate for fixing of wire cloth in steel & wooden windows/ventilators with MS flat from 15 x 3mm and fixing of wire cloth in wooden shutters with 2nd class hard wood beading all as specified and directed .

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed.

S& F of flush door 30mm thick membrane doors decorative finish on one side duly finished and polished and other side all as per manufacturers directions as per tint / colour including necessary teak wood lippings of necessary all as directed by Engr - In Charge.

S&F of mild steel flats as in hold fasts; wall ties; plain angle cleats for securing purlins to wood trusses and wiremesh conforming to Fe-290 Gde-E-165 all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

Ditto all as per item ser No 27 as above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders all as specified and as directed.

M&L for mild steel TMT bars 06 to 08mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 all as specified and as directed.

S&F of powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. aluminium section of powder coating of minimum thickness of 50 micron complete all as specified and as directed.

S&F of powder coated anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed

S&F of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

M&L for Cement concrete 1:2:4, 75mm thick, type B-2 (using 40mm graded stone aggregate) as in plinth protection all as specified and as directed.

M&L 75mm thick type E-2 (1:5:10) cement concrete (using 40mm graded stone aggregate) for sub base of floor finishing all as specified and directed.

M&L for Cement concrete 1:4:8, 75mm thick, type D2 (using 40 mm graded stone aggregate) as sub floors, sub bases, floors and pavings, etc all as specified and as directed.

M&L for Cement concrete 1:2:4, 25mm thick, type B1 (using 20 mm graded stone aggregate) as sub floors, sub bases, floors and pavings, etc., finishing cement concrete surface even and smooth without using extra cement all as specified and as directed.

M&L for Cement concrete chequered tiles 20cm x 20cm x 20mm thick, with mixture of white cement & pigment machine pressed rubber moulded of specified pattern, set jointed in neat cement slurry in floors as specified and as directed

M&L for rendering 15mm thick cement plaster in CM 1:4 on fair face of brick work or concrete surfaces and surface finished fair and even all as specified and as directed.

M&L for rendering 10mm thick cement plaster in CM 1:6 on brick work or concrete surfaces even & smooth without using extra cement on internal walls all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick screed bed in cement mortar 1:6 for laying floor finishes all as specified and as directed.

M&L Glazed coloured ceramic tiles of size 450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match as in skirting/dado over 10 mm thick back coat in CM 1:4 all as specified and directed in toilets and kitchen all as specified and directed.

M&L Non - skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., including screed bed 15mm thick in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and directed.

M&L Non - skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting/dado, including back coat in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and directed.

M&L for Preparation of the new surfaces of walls plastered, and applying two cots of cement base paint , complete all as specified and as directed.

M&L for Preparing the new surfaces of wall and applying two coat of oil bond distemper over a coat of interior wall care putty all as specified and as directed

M&L for preparing new or previously untreated wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed.

M&L for painting of new or previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise described using two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

S&F sheet glass ordinary quality 5mm thick as in doors, window, showcase aluminium frame work & similar work with or without glass roller any size including neoprime gasket all as directed by Engineer-in-Charge

S&F for 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane all as specified and directed.

Supply and fix GI tubing light grade 40mm bore in trenches /fixing on pole /wall /crossing in drain etc. for protection of UG cable all as specified and directed all as specified and directed.

Cutting existing 40mm bore water mains and inserting medium grade GI/CI Tee 40 mm x 25mm for taking branch connection including fittings and joints complete all as specified and directed.

Supply and lay GI pipe 40mm bore “Medium grade”, with necessary fittings as in trenches complete all as specified and directed.

S&F High density polyethylene pipes 50 mm bore of pressure ratings 6 kgf/cm2 fixed complete to walls,floors,ceiling etc. Including necessory fittings all as specified and directed.

Supply only Pillar tap 15mm bore fancy type chromium plated, with capstan head screwed down high pressure with or without lettered “Hot or cold” with long screwed shanks fly nuts ,screwed for iron pipe and fixed completed all as specified all as specified and directed.

S&F of 110mm dia bore, PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including flat iron clamp for proper fixing complete all as specified & directed by Engr-in-charge all as specified and directed.

S&F of 75mm dia bore, PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including flat iron clamp for proper fixing complete all as specified & directed by Engr-in-charge.

S&F PVC(SWR) bends 110mm dia complete all as specified & directed by Engr-in-Charge all as specified and directed.

S&F PVC(SWR) bends 75mm dia complete all as specified & directed by Engr-in-Charge all as specified and directed.

M&L for concrete bed to drain pipes in PCC 1:4:8 type D2 (using 40mm graded stone aggregate) including packing under and haunching against sides of pipes after they are laid and tested for 150mm dia pipe all as specified and directed.

M&L for Reinforced concrete pipes, class NP2, 150mm dia laid and jointed complete with collars all as specified and directed.

M&L for 450mm reinforced concrete pipes, class NP2 laid and jointed complete with collars including concrete bed all as specified and directed

M & L for Cutting into existing manholes 150mm dia for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required all as specified and directed

S&F vitreous China squatting pan 'orrisa' pattern white colour of size 580x440mm with integral foot rests including provision of lime concrete complete all as specified & directed by Engr-in-charge .

S&F 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flush pipe complete all as specified and directed.

S&F vitreous china wash basin, white or coloured of size 550 x 400 mm with padestal including brackets and fixing of pillar tap all as specified and as directed all as specified and directed.

S&F CP Towel rail of including fiitings of neccessary screws etc complete all as specified and directed by the Engr-in-Charge.Make - Jaguar (Code-AKP-35711PS) all as specified and directed.

S&F 15 mm dia bib cock wall flange (fancy type), cast copper alloy with with screwed down, screwed for iron pipe or for brass ferrule complete with check nut 15mm bore complete all as specified and directed by Engr-in-Charge.. Make - Jaguar (Code-VGP - 81037) or Equivalant

S&F Angle cock with wall flange 15 mm dia Fancy type Make - Jaguar, Cat Part No - VGP-81053 or Equivalent all as specified and directed.

M&L for 75mm dia of outlet PVC Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr-in-Charge.

S&F for aluminium powder coated drapery rod 32mm dia fixed with suitable bracket complete all as specified and as directed. Note : Bracket will be measured and paid separately.

S&F for aluminium powder coated fancy type suitabe brackets fixed at both ends of openings fixed over 1st class hard wood rounded wooden blocks of 65mm dia and 20mm thick fixed to stone wall/Brick wall using screws incl necesary drilling & finished with polishing Each opening shall have two fillets at both ends all as specified and directed.

M&L for 600x600mm false ceilling tiles (Gypsum board of decorative type) of 9 mm thick with GI main tee of Size 24x32mm , having 0.27 mm gauge @ 1200 mm c/c. rotary stiched cross tee size of 24x27mm, guage 27 mm and cross tee of size 24x27mm having 0.25mm gauge @1200mm c/c and angle of size 19 x 19 mm gauge 0.35 mm fixed on perifery of wall and all the above grids are suspended at every 1200 mm c/c in both direction by 2mm thick GI wire and all as per manufacture instructions all as specified and directed.

Supplying and laying un-reinforced precast concrete cable cover, class LV, Type 1 with peak, size 250 mm x 150mm x 40mm all as specified and directed.

Supply and laying in trenches, floors, roof, ducts, LT underground cable of size 2 core 6 Sqmm XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands, jointing materials etc. and fixing using clamps, saddle for pole, wall etc. all as specified and directed

Point wiring completed with 1.5 sqmm single core PVC insulated heavy duty ISI Marked unsheathed FRLS copper conductor cable 1100 volts grade with multistranded copper conductor drawn through concealed PVC conduit and including provision of PVC Insulated heavy duty ISI marked Unsheathed copper conductor,1.5 sqmm for earth continuity conductor and connected to common earth dolly, including suitable size of sheet metal box 1.6mm thick fixed and flushed inside the walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets, fan regulators etc., all as specified and directed for the following: -

(a) One light/wall mounted/exhaust fan point controlled by one 5 Amps switch all as specified and directed.

(b) One switch socket outlet point 3 pin 5 Amps on same board with other switches all as specified and directed.

All as per item No 78 above but wiring with 2.5 sq mm FRLS copper cable including earth continuty conductor with 2.5 sq mm FRLS copper cable for one 6 pin 15 Amps socket outlet on independent board controlled by 15 Amps switch all as specified and directed.

Supply and fix LED lights fitting 20 Watt, 220V, 4 feet long, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge.

Supply and fix LED lights fitting mirror type with high out put diffiuser 2 feet, 10 Watt, 220V, 4 feet long, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge.

Supply and fix switch piano 5 Amps flush type one way all as specified and directed.

Supply and fix socket outlet 3 pin 5 Amps flush type all as specified and directed.

Supply and fix switch socket combination 3 pin 16 Amps multi pin flush type all as specified and directed.

Supply and fix sheet metal enclosures for MCB distribution board 230 Volts Single pole and neutral 4 way double door with 200 amps rated bus bar complete including flushing the DBs inside the wall and making good to the disturbed surfaces and also matching with the existing surface all as specified and directed by Engr in charge.

S&F ceiling rose, three terminal, PVC/polycarbonate, isolated body, ISI marked complete all as specified and directed.

S&F CPVC pipes 20 mm SDR 11 & Plain VPVC SDR 11 on walls, ceiling orf laying including fitting in floors all as specified and as directed by Engr in Charge all as specified and directed.

S&F CPVC pipes 25 mm SDR 11 & Plain VPVC SDR 11 on walls, ceiling orf laying including fitting in floors all as specified and as directed by Engr in Charge all as specified and directed.

S&F 500 ltrs capacity Rotational moulded polythene water storage tanks (cylindrical vertical with closed top, two layers) hoisted and fixed in position including tank niple 25mm dia and complete all as specified and directed by Engr-in Charge.

S&F Vitreous china urinals, bowl type of size 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, brackets, flush pipe, waste pipe grating and union for discharge pipe fixed complete all as specified and directed

Supply and fix building security light LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP-66 protection complete all as specified and directed by Engr-in-Charge.

Supply and fix exhaust fan 250mm sweep, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding complete all as specified and directed by Engr-in-Charge all as specified and directed.

Supply and fix MCB SP 6 to 32 Amps, 240 Volts, 'C' Curve, 10 KA rupturing capacity all as specified and directed.

Supply and fix MCB SPN 32 Amps, 240 Volts, 'C' Curve, 10 KA rupturing capacity all as specified and directed.

Supply and fix wall mounted cabin fan 400 mm sweep, 220-240 volt AC, 50 Hz sigle phase with Thermal overload Protected Motor and connecting up including provison of cabe from ceiling rose/connector to Wall fan all as specified and directed.

M & L for Earthing complete with galvanised earth plate electrode of size 600x600x6 mm thick burried directly in ground earth pit not less than 2.25 m below ground level with top edge of earth plate not less than 1.5 mtrs below ground level connected to 4 mm dia GI earth wire as earth lead upto a length of 7.5 metre long by means of bolts,nuts, washers etc. and protected by GI pipe light grade 15mm dia and 20mm dia GI tubing light grade with funnel for watering, all as shown in electrical plate No 3 of SSR Part-I, back-fill with salt and charcoal, provision of test point including connected to earth test point and necessary earth work excavation in any type of soil PCC (1:3:6) type C1 bed and chamber RCC (1:2:4) type B1, iron grill including GI cover with hinge and funnel watering pipe etc all as specified and directed by Engr-in-Charge.

AURA ENTERPRISES

Raghu M Contractor

A. N. Kalbhavi