Renovation of House No. 231 (Type 10) Sector 7, Chandigarh. (IBM Scheme No. W4/2026/25427)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :DSR 2.10

Pipes, cables etc, not exceeding 80 mm dia DSR 2.10.1.1

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia DSR 2.10.1.2

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:DSR 6.1

Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.1.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings as DSR 17.28

32 mm dia DSR 17.28.2.1

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. : DSR 18.10

15 mm dia. nominal bore : DSR 18.10.1

20 mm dia. nominal bore : DSR 18.10.2

32 mm dia. nominal bore : DSR 18.10.4

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.: DSR 18.78

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : DSR 18.46

15 mm nominal bore : DSR 18.46.1

20 mm nominal bore : DSR 18.46.2

Cutting holes up to 30x30 cm in walls including making good the same: DSR 18.76

With common burnt clay F.P.S. (non modular) bricks : DSR 18.76.1

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. : DSR 18.77

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:

W.C. pan with ISI marked white solid plastic seat and lid. DSR 17.3.1

Providing and fixing uplasticised PVC connection pipe with brass unions : DSR 18.21

45 cm length : DSR 18.21.2

15mm nominal bore DSR 18.21.2.1

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 DSR 18.49

15 mm nominal bore. DSR 18.49.1

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. DSR 18.51

15 mm nominal bore. DSR 18.51.1

Providing and fixing C.P. brass angle valve for basin mixer and geyser points ... DSR 18.53

15 mm nominal bore. DSR 18.53.1

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.

20 mm nominal bore, 120 mm long, weighing not less than 198 gms DSR 18.62.2

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :DSR 18.17

20 mm nominal bore DSR 18.17.1A

Providing and fixing of C.P. brass Jet with brass nossel steel flange & PVC flexible pipe complete in all respect make DSR 17.16A

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. DSR 18.52

15 mm nominal bore : DSR 18.52.1

Providing and fixing CP Brass Extension Nipple ( Size 15 mm x 50 mm ) of approved make and quality as per direction of EIC DSR 18.53A

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : DSR 17.60

100 mm inlet and 75 mm outlet DSR 17.60.2

Sand cast iron S&S as per IS - 3989 DSR 17.60.2.1

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.. DSR 18.48

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : DSR 17.25

Flat back wash basin of size 550x400 mm DSR 17.25.2

Providing and fixing of C.P. Steel Grating Heavy (With hole without hole) 100 mm dia, of approved make.

Providing and fixing of CP Brass/SS Towel Ring with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36524 Warna or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Brass/SS Towel Rail 600mm of with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36520 Warna or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Brass/SS/ABS overhead shower with swiveling Joint , 125mm dia (min) with C.P Brass/ S.S Shower Arm and flange to the satsifaction of EIC of approved make ESSCO Model No. 536A & 542A or equialent Model of CERA /Kerovit/ Jal

Providing and fixing of CP Brass/SS/ABS Soap Tray made of Plastic including glass bowl of approved make Jal Model No. 36540 or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of CP Pillar Cock of approved make.

Providing and fixing of CP Waste for Basin of approved make.

Providing and fixing of CP sink Waste for S.S Sink as per approved make.

Providing and fixing of GI Elbow 75mm x 32mm complete in alll respect.

Providing and fixing of C.P. cup heavy duty make of approved make

Providing and fixing HCI Cover with frame for GT & IC of approved make

Providing and laying of UPVC pipe, IS-4985 marked, Pressure 6 kg/cm2 including cutting, joining, solvent and all necessary fittings complete in all respect except excavation of approved make

Prov. & fixing of looking mirror of size 450x600mm made with 5mm thick (minimum) superior quality glass including cost of hard board, PVC beading and C.P. Screw etc. to satisfaction of EIC of approved make

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required (27" X 20" X 8") of approved make

Please Enable Macros to View BoQ information