GE/U(N)-52/2020-21PROVN OF DEFICIENT TOILET BLOCK FOR SINGLE LIVING JCOS IN CHNC INCLUDING CERTAIN REVENUE AND MINOR WORKS UNDER AGE B/R-I OF GE(NORTH) UDHAMPUR

Amount

Excavation in trenches in hard/dense soil not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation etc or for shafts, manholes, pier holes etc n.exc 10 sqm on plan and not exc 1.50m in depth and getting out in any type of soil, complete all as specified and directed by the Engr-in-charge.

Excavation over area n exc 1.5m in depth and getting out in any type of soil, complete all as specified and directed by the Engr-in-charge.

Ditto all as above item No. 2 but for each additional 1.5m or part therof in depth beyond the first 1.5m depth complete all as specified

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. complete all as specified as directed.

Returning, filling in, under floor including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed by the Engr-in-charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting pointcomplete all as specified and directed by the Engr-in-charge.

Demolition of plain cement concrete below or above ground level n exc 15 cm thickness and removal of soil to outside MD land complete all as specified and as directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15 cm thickness (below or above ground level). complete all as specified and as directed by Engr-in-charge

Demolition of brick work or stone masonry built in cement mortar including all quoines arches,pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed by Engr-in-charge

PCC 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by the Engr-in-charge.

Taking down chowkats or frames (without taking off shutters from frame) exc 1.50 Sqm and not exc 4.00 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and directed by the Engr-in-charge..

Taking down chowkhat with shutter n exc 1.5 sqm each and refixing in same opening after completion tiling work complete all as specified.

Rendering 10 mm thick cement plaster on fair face of brick work or concrete surfaces of wall in cement mortar 1:6, finished even and smooth without using extra cement, complete all as specified.

Rendering 15 mm thick cement plaster on fair face of brick work or concrete surfaces of wall cement mortar 1:4 in two layer (10+5) secound layer mixed with water proofing compound as per manufacture instruction and finishedand directed . even and smooth without using extra cement including scapfolding arrangements up 2nd floor where ever is requried complete all as specified Note WPC shall be measured and paid saperatelly under relivent item .

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over and including a coat of 1mm thick wall care putty including scapfolding arrangement as per site requirement upto 2nd floor complete all as specified

Preparation of new plastered surfaces of wall and applying two coat of oil bound distemper one coat of primer over and including 1mm thick wall care putty finish , complete all as specified and directed by Engr-in Charge ..

Hardcore of Broken stone/boulders gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface complete all as specified and directed by the Engr-in-charge.

75mm thick Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base of flooring etc, complete all as specified and as directed by Engr-in-charge.

150 mm Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified.

PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) concrete bed to 150 mm bore drain pipes including forming cradles after they are laid and tested all as specified

Pre-cast RCC 1 : 2 : 4, type B-1 (using 20 mm graded stone aggregate) in cover slabs for man holes including MS handle, with plain faces finished fair and smooth etc, set in CM I : 6 complete all as specified

PVC (SWR) vent cowl 75mm bore complete all as specified and directed by the Engr-in-charge.

PVC (SWR) vent cowl 110mm bore complete all as specified and directed by the Engr-in-charge.

PVC (SWR) 75mm junction single, (Single T) equal or unequal with oval access door complete all as specified and directed by the Engr-in-charge.

PVC (SWR) 110mm junction single, (Single T) equal or unequal with oval access door complete all as specified and directed by the Engr-in-charge.

25 mm thick cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in flooring as in subbase and finished even and smooth complete all as specified and directed by the Engr-in-charge.

Coloured glazed ceramic coloured tiles 600 mm x 300 mm / 7 to 8mm thick on vertical surfaces of walls as in dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 and fair to recive tiles as in skirting/dado etc complete all specified

Plain cement concrete tiles coloured designer interlocking paver of 60mm thick having glossy finish, colour and pattern as approved by Engr-in-charge strength not less than 350 Kg/Sqcm (tested as per IS 1237-1980) laid over and including 50mm thick dry river sand cushioning and voids filled with dry sand and surface compacted with surface vibrator complete all as per manufacturer instructions, specified and as directed by Engr-in-charge.

Anti skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm in floor etc, set and jointed and laid with spacers and pointed with epoxy and pointed in colour tile grout including screed bed or bedding layer of mortar 10mm thk for laying floor finishes in CM(1:4) complete all as specified

Providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight.

Brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 metre mean radius, using old size bricks, built in cement mortar 1:6 , complete all as specified and as directed. .

Solid PVC door frame of wallnut colour of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube in opening as per specification and drawings complete all as specified and directed by the Engr-in-charge.

Factory Made PVC Moulded Door Shutter of wallnut colour , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed.complete all as specified and directed by the Engr-in-charge.

150 mm long aluminium bow handles, cast type, anodised and fixed.complete all as specified and directed by the Engr-in-charge.

300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by the Engr-in-charge.

Butt Hinges 100 mm long medium weight cold rolled mild steel and fixed complete all as specified and directed by the Engr-in-charge.

Wash down water closet (Pedestal pattern), complete with Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc.including PVC Seat and cover for pedestal pan . complete Make - CERA cat part No. 2080 (Camelia), Jaquar CNS-WHT-OP01

Squatt pattern including cement concrete bedding , size 580 x 440mm including PVC (SWR) 'P or s trap front and back inlet and with internal foot rests (excluding flushing cistern ) including connector pices of PVC (SWR) Pipe as per required upto T /Y joint.complete all as specified and directed by the Engr-in-charge. Make - CERA Cat part No-2071 or equilvent of any approved make as approved by GE.

PVC low level flushing cistern of capacity 10 ltr. white with inlet, ball valve, float and handle including breckets, suitable flush pipe of polyethylene of low or high density or PVC 32mm dia and connection to pipes complete all as specified and directed by the Engr-in-charge. CERA cat part No. 2602 P (Camelia), or equilvent of any approved make as approved by GE.

Oval under counter wash basins, size 560x470mm vitreous china fixed in RCC slab including CP waste coupling 32mm and CP brass Bottle trap 32mm bore including 32mm HDPE pipe bend fixed to wall etc as in waste pipe and 300mm long (Cera CM 104B) complete all as specified CERA cat part No. 1005A (Ivory colour) for WHB or equilvent of any approved make as approved by GE.

Chromium plated, 15mm WHB Mixer swan neck , heavy duty fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by the Engr-in-charge.Make- CERA/Jainko/Jaquar or equilvent make as approved by GE

Stainless steel soap tray as per sample fixed with wooden gutties and screws to wall surfaces complete all as specified. complete all as specified and directed by the Engr-in-charge.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed by the Engr-in-charge.

PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed by the Engr-in-charge.

PVC (SWR) pipes of bore 110mm single socketed in any length with rubber ring joints laid in floors/fixed to wall complete all as specified.

PVC (SWR) pipes of bore 75mm single socketed in any length with rubber ring joints laid in floors/fixed to wall complete all as specified.

PVC (SWR) bends with access door any radius of bore 110 mm complete all as specified and directed by the Engr-in-charge.

PVC (SWR) bends with access door any radius of bore 75 mm.complete all as specified and directed by the Engr-in-charge.

Red granite(of any type)stone slab 16mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with rounding to edges of stone slabs one edg complete Including 10mm thick backing coat CM 1:4 complete all as specified and as directed by Engr-in-Charge.

3 layer rotational moulded polyethylene water storage tanks white colour 2000 ltr Capacity (Cylindrical vertical with closed top) with 20 mm ball valve, epoxy coated aluminum rod, plastic ball etc, hoisted and fixed in position including tank Nipple inlet and outlet and conneting pipes all as specified in SSR Part I complete all as specified & as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal from site to store bore of pipe 15mm complete all as specified and directed by the Engr-in-charge.

"-do" but bore of pipe 20mm complete all as specified and directed by the Engr-in-charge.

Supply & Fixing tubes , medium grade of bore size 15 mm including all fixing accerroies and laid in ceilings or laid in floors Including taking connection from existing main line complete all as specified and directed by the Engr-in-charge.

"-do" but bore of pipe 20mm all as specified.

"-do" but bore of pipe 25 mm all as specified.

Supply and fixing in replacement bib taps long body 15mm chroimum plated (ISI Marked with valid CML No) with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed including elbow/socket etc as required at site all as specified and directed by Engr-in - Charge..

Supply and fixing bib taps long body 15mm chroimum plated (ISI Marked with valid CML No) with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed including elbow/socket etc as required at site all as specified and directed by Engr-in - Charge.

Supply and fixing CP shower rose of dia 125mm with arm 15mm size 195mm long with bend of 45 degree with flange complete

Supply and fixing Angle cock 15mm chromium plated fittings as required at site all as specified and directed by Engr-in-Charge.

Supply and fixing concealed stop valve chromium plated brass fancy type screwed down high pressure with crutch or butterfly handle dia 15mm screwed both ends for iron pipe or for unions and fixed including fittings as required at site,all as and directed by the Engr-in-charge.

Supply and fixing CP shower rose of dia 125 mm with arm 15mm size 195mm long with bend of 45 degree with flange including taking down the existing UNSV shower of any type/shape complete

Supply and fixing Angle cock 15mm chromium plated fittin as required at site and taking down existing unserviceable angle cock all as specified and directed by Engr-in-Charge. Make- CERA/Jainko/ Jaquar or equilevent make approved by GE.

Supply and fixing concealed stop valve chromium plated brass fancy tpecrewed down high pressure with crutch or butterfly handle dia 15mm screwed both ends for iron pipe or for unions and fixed including fittings as required at site taking down existing unserviceable ,all as and directed by the Engr-in-charge.

Towel Rod CP Brass 20mm bore and 600mm long fixed with screw and plug complete all as specifed

Towel Ring CP Brass fixed with screw and plug complete all as specifed

Looking Mirror of size 600mm X 450mm X 5mm thick with Plywoof commercial type fixed on back side and wooden frame compete all as specifed.

75 mm bore PVC(SWR) multi/single floor trap with stainless steel grating including jointing to waste pipe fixed in cement with solvent cement, including taking down old PVC or CI floor trap of any type complete all as specified.

Roof trusses (framed), trussed, purlins, Tubular pipe, MS plates, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including Chequered plates and plain plastes of any thickness and distance pieces, cleats and including MS bolts etc conforming to Fe-410- W(Gde-E-250) quality- B complete all as specified and directed

Mild steel sheet 1.60mm thick fixing in hearths,covering to door shutters and welded to door frame complete all as specified and directed.

Preparation of steel surfaces of any description over 10cm width or girth not other wise describe, two coat of synthetic enamel paint and over one coat of red oxide primer complete all as specified and directed by the Engr-in-charge.

Pre-painted coloured profiled Galvalume/ Zincalume sheet 0.50mm thick TCT of grading YS-550, coating class AZ-150, class-3 confirming to IS-15965-2012, pitch profile c/c n.exc 203mm & crest of profile not less than 28.5mm as in roof covering/cladding to wall fixed with self taping screws/fastners with EPDM seals including gap filling between sheet and wall with PCC (1:3:6) as per site requirement complete all as specified and directed by Engineer

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in Ridge /cladding to wall, or on ridge fixed with self tapping screws as specified

Providing plain cement concrete 1:2:4, type B-0 using 12.5 mm graded crushed stone aggregates as in cills, steps, seismic and other similar bands, parapets and railings up to 60 cm in height, coping, kneelers, apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles and throating as directed .

False ceiling with Everest Fibre Cement Designer tile Ivory/white painted (High Pressure Steam Cured) of 4mm thickness (as per IS-14862) of size 595mmx595mm and any one of the design (occeanic , lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanised @120 gms, both sides inclusive) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0..30mm thick sheet and cross T of size 15x32mm made of 0.30mm sheet spaced between main T at 600mm c/c from a grid of 600x600mm and wall angle of size 15x20mm made of 0.30mm thick sheet and laying false ceiling tiles in the grid including required cutting/making opening for services like diffusers grils, light suspended from ceiling using GI soffit cleats fixed to existing rafters, purlin etc with dash fastners GI adjustable rods of 3mm dia wit galvanised butterfly level clips, spaced at 1200mm c/c along main T, bottom exposed width of 15mm of all T-sections shall be centre black pre-painted with polyester painnt and having a load bearingcapacity of 12 kg/sqm and refixed all exesting electric wiring and fixture all complete at all heights as per directed

Factory made heavy duty full body digital matt finish, paving coloured tiles of size300mm x 300mm x 10mm thick for external use laid over and including 10 mm thick screed bed or bedding layer in CM 1:4 including jointed with neat cement slurry and pointed in coloured tile epoxy grout to match the shade of tiles complete all as specified. Make- Durastone of Somany, Pavigers of Kazaria, Endura of Johnson.

Providing cement concrete 1:3:6 type C-1 ( Using 20 mm graded crushed stone aggregate ) as in coping, Gola etc including necessary formwork as required complete all as specified and as directed by the Engr-in-charge.

Plain cement concrete 1:2:4 type B1, using 20mm graded stone aggregate as in coping etc including weathering, slightly rounded or chamfered and trading as directed by Engr-in-Charge complete all as specified and directed.

Providing precast cement concrete 1:2:4 in road side kerb stone etc (of any section indicated) with plain fair faces, including chamfers, weathering, throating etc and setting in cement mortar 1:4 complete all as specified.

Surface excavation for hard/dense soil n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out complete all as specified and directed

RCC Bend/slab 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) (Nominal Mix) as in slabs supported on wall, beams etc or similar works, complete all as specified and directed by Engr-in-Charge.

TMT steel bars 10 mm dia and over as in refinforcement, cut to length, bend to shape required including craniing, bending spirally or hooping for coloumns, hooking ends and binding with MS wire (annealed not less than 0.9mm) all as specified and as directed by Engr-in-charge.

Use and waste form work to side and soffits of subpended slab such as roof slab floor slab landing and similar work not exceeding 200 mm thick (horizontal or sloping) for rough finished surface of concrete flat, complete all as specified and as directed by Engr-in-charge.

Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed by the Engr-in-charge.

Powder coated (of approved colour ) aluminium sections as in frame & shutter of windows / ventilators with 3 track sliding aluminium frame and shutters including necessary rollers and locking arrangements and fixed frame etc fixed to wall including, powder coated aluminium Deco grill DG 202 pattrn with apperture of size 60x45mm securing with suitable aluminium channel to frame, Stainless steel mosquito proof wire cloth of stainless 0.36mm dia and 1.4mm aperture fixed with aluminium flat/channel and screws and Glazing with 5mm thick frosted/tinted sheet glass exc 0.50 sqm in each panel fixed to aluminium section of doors, windows and fixed frame with suitable EPDM rubber packing and powder coated aluminium beading to frame complete all as specified as directed by Engr-In-Charge. Make : JINDAL/ HINDALCO/INDALCO/

Powder coated (of approved colour ) aluminium sections as in frame & shutter of doors, windows (Hung/sliding), ventilators (louvers/fixed type) and fixed frame etc fixed to wall including, preparation of disturbed portion both side (internal & external surfaces of wall) match with existing surface treatment and all sides of aluminium frame shall be sealed with silicon sealent (inner/outer face) complete all as specified as directed by Engr-In-Charge. Make : JINDAL/ HINDALCO/INDALCO/

Glazing with 5mm thick frosted/tinted sheet glass exc 0.50 sqm in each panel fixed to aluminium section of doors, windows and fixed frame with suitable EPDM rubber packing and powder coated aluminium beading to frame complete all as specified.

Stainless Steel 'S' Shape Handles 300mm long Fancy type fixed with screws to door shutters complete all as specified.

Floor door stoper of 140mm long of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and directed by the Engr-in-charge.

Aluminium powder coated (match with door shutters) Hydraullic door closer suitable for aluminium glass door shutters of 851 to1000 mm in width and of weight between 61 to 80 kgs and fixed.complete all as specified and directed by the Engr-in-charge. Make- Godreg/Jindal

Powder coated Hinges 125mm long match with door shutters fixed to door shutters with screw complete all as specified.

Powder coated Aluminium Towerbolt Hinges 200mm long match with door shutters fixed to door shutters with screw complete all as specified.

Mortice lock with two lever brass body (vertical type) 100mm length of latch with 3 set of keys fixed in door shutter with proper in position complete all as specified.

Walling of random rubble, uncursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and as directed by the Engr-in-charge.

Mild steel framed work such as Iron door , grills, gratings, flats, holdfast, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladders; framed balusters; railing;frame work for water tanks and similar work conforming to Fe 290.Gde-E-165, all as specified .

Sliding Roller for sliding door (04 Nos wheels in each roller) foxed to aluminium door with screw in position complete all as specified.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FR-LSH insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FR-LSH insulated drawn into and including concealed PVC rigid conduit 1.5mm wall thickness ISI marked terminated into CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etcOne light point controlled by one, one way switch 5 Amp complete complete all as specified and as directed by the Engr-in-Charge for the following :-

All as per srl item No 99 above but forOne 3 pin sockt outlet 5 Amp on the same board with other switch

All as per srl item No 99 above but for one 3 pin socket outlet 15 Amp independent with cable of size 4 Sqmm for piont wiring and 2.5 sqmm as in contineous earth wire.

S&F Switch Piano, flush type, One way, single pole, 5 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F Socket 5 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F Switch socket combination 5 / 15 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F Ceiling rose, 3 terminal, PVC / polycarbonet, isolated body complete all as directed by Engineer - in - Charge.

Slim linear LED lighting fixture 20 watt LED batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete all as per the direction of Engr-in-Charge. Make -Make of LED -SYSKA as per ordering code SSK-ALB-20W or equivalent model of Havells or CG

Slim linear LED lighting fixture 10W watt LED batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, complete making all connection from ceiling rose to fittings including testing complete all as per the direction of Engr-in-Charge.

Supply and fixing Water heater storage type, electric,capacity 25 litres.BEE 5 star rated complete all as directed by Engineer - in - Charge.

Providing exhaust fan AC single phase 230/240 volts of size 300mm sweep with louvre complete including making suitable size hole and grounting bolt, nuts with washer complete and making good the distruibed surface complete all as specified and directed by the Engr-in-charge.

Providing exhaust fan AC single phase 230/240 volts of size 450 mm sweep with louvre complete including making suitable size hole and grounting bolt, nuts with washer complete and making good the distruibed surface complete all as specified and directed by the Engr-in-charge.

Sheet metal enclosure double door single pole and neutral 240 Volts for DB's when MCBs to be used 8 way with 200 amp rated bus bar with IP-43 protection. MakeLegrand Cat Part No 607711 complete all as directed by Engr-in-Charge.

Supply fixing, connection and testing MCB SP6-32 Amps C series, breaking capacity 10 KA of rating 6-32Amps complete all as specified and directed by the Engr-in-charge.

Supply fixing, connection and testing MCB SPN 32-63 Amp, 240 Volts, 'C' series, breaking capacity 10 KA of rating 32-63Amps complete all as specified and directed by the Engr-in-charge.

Supply and lay XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core in trenches/floor/pole/GI pipe complete including cuttingof bituminous road/chasing to any surface and making good to the disturbed surface to match the existing complete all as specified and directed by the Engr-in-charge.

Dry sand cushioning to under ground cables provided with a layer of sand 8 cm deep before laying the cable, 15 cm depth after laying cable & stretching the cable all as specified and directed.

Supply and lay brick class ‘B’ covering as mechanical protection to cable with well burnt all as complete all as specified and directed by the Engr-in-charge.

GI tubing light grade with all fitting and fixed in wall and floor or fixed to pole of size 40mm dia complete all as specified and directed by the Engr-in-charge.

Earthing complete with galvanized steel earth electrode 60cmX60cmx6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level ) with top edge of the plate not less than 1.5m below normal ground level connected to earth lead by means of bolts nuts and washers of GI steel and including earthing pit charcoal, common salt, GI 4.0mm dia lead wire 20mm GI medium grade watering pipe 15mm bore light grade protection pipe 5 Mtr length with wire mesh and funnel PCC pit in PCC 1:2:4 type B-1 using 20mm graded stone aggregate, angle iron frame and RCC cover and earth work complete all as shown in electrical plate No.3 of SSR -2009(Part-1) complete all as specified and directed by the Engr-in-charge.

Ceiling fans complete with electronic type regulator and accessories 230 V,1200 mm sweep complete all as specified and directed by the Engr-in-charge..Make- Havells (ES-50) or equivalent in Bajaj

Cutting hole in existing wall for making opening for fixing of exhaust fan of size 300/450mm sweep including grounding bolts, nuts and making good disturbed surface of wall etc complete all as specified and directed by the Engr-in-charge.

Plug and socket DBs, double pole and neutral enclosure with a two pin earth plug and socket with one single 20 Amps, 240 volts MCB complete all as specified and directed by the Engr-in-charge.

Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm dia complete all as specified and directed by the Engr-in-charge.

Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed for 15mm bore size complete all as specified and directed by the Engr-in-charge.

Cutting, chasing walls, making good to facing and pointing in cement mortar (1:3) to edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chasing for concealed water tubing or concealed conduit wiring etc and making good and cutting not exc 10 CM girth complete all as specified and directed by the Engr-in-charge.

M/S GURU DEV BUILDERS

KUMAR CONSTRUCTION CO

MADAN LAL SHARMA AND SONS