Development of parking and vehicle checking security arrangement at TVS , BARC, Trombay, Mumbai.

Amount

Lead charges for lead exceeding 3 KM but not exceeding 4 KM, by mechanical transport including loading, unloading, stacking / levelling etc.

Murum filling under floors of specified thickness in layers of not more than 150 mm thickness including supplying required materials and consolidation etc. complete (Murrum to be brought from out side campus of BARC)

Providing and laying in position cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) including consolidation, finishing, curing etc. complete as per specificationsand drawings but excluding the cost of Form work shuttering, centering Complete at all levels

Providing , laying and fixing at or near ground level Factory made Kerb stone of precast cement concrete M-25 grade in position and size of 325 mm height, 125 mm thick at bottom , 75 mm thick at top partly tappered as per approved patterns and setting in position with C.M 1:3 (using crushed sand) including consolidation, curing, cost of required centering, shuttering, finishing smooth with 6 mm thick cement plaster 1:3 (using crushed sand) on exposed surfaces complete as per specifications and as directed by the Engineer-in-charge. ( Length finished Precast kerb edging shall be measured for payment

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels

Providing and laying in position cement concrete of 1:1.5:3 at all levels (1 cement, 1.5 crushed sand, 3 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc.. complete as per specifications and drawings but excluding the cost of shuttering, centering and steel reinforcement.

Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to Plinth Level.

Providing and laying design mix cement concrete of M-30 grade in roads, taxi tracks and runways using crushed Sand, graded stone aggregate of 20 mm nominal size in appropriate proportions as per specified design criteria approved by Engineer-in-charge, mechanically vibrated using needle / Surface vibrators including steel form work with sturdy M-S channel sections including curing and providing and filling construction joints and dummy joints with approved joint filler primer or equivalent including rounding of the edges and filling the grooves 10 x 25 mm deep at top for construction joints and 10 mm x 50 mm deep at top for dummy joints with joint sealing compound (conforming to grade B of IS:1834) including making necessary arrangements for expansion joints etc all complete as directed by the Engineer-in-charge

Extra for RCC/PCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants .

Providing Reinforcement Steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings.

Using TMT Bars of all grades of all size bars

Providing, centering, shuttering Form work using steel plates, timber planks for all types of structures including necessary strutting, proping, staging, supports, bracings etc. and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels

For Sub Structure

Providing and fixing in position 25 mm thick Joint filler board of approved make in expansion joints to the required size and shape, placing and keeping in position complete as per specifications and drawings and as directed by the Engineer in charge.

Providing and constructing Half brick masonry using bricks of approved quality / class, brand/ make in partition walls in C.M 1:4 (using crushed sand) including scaffolding, raking out joints, curing etc. complete and with stiffners of RCC 1:2:4 (105 X 75 mm size) at every 900 mm height including form work curing etc. complete as per specifications and as directed by the Engineer-in-charge but excluding reinforcement up to plinth level. (Reinforcement will be paid under relevant item)

Providing Structural steel work using angles, channels, joists and other sections, welded and / or bolted in built up sections for trusses , structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Engineer in charge

Up to and including 300 mm Joists, 350 mm channels, and below sections using materials of approved manufacturers or of approved quality or product meeting technical parameter. All test reports to be provided along with the supply of the materials

Providing Structural steel work in M.S Plain Plates and chequrred Plates for Embedded Parts, Trench Covers, Connection plates etc.including cutting, hoisting, fixing in position and applying a priming coat of approved zinc chromate steel primer etc.including cost of structural steel Plates, welding all labour charges etc. complete as per drawings and specifications.

Using materials of approved manufacturers or of approved quality or product meeting technical parameter .All test reports to be provided along with the supply of the materials

Providing, supplying, cutting, welding, fabricating, hoisting and fixing in position structural steel members like trusses, purlins, posts etc. using MS hollow / circular / square / rectangular tubular sections including appling a coat of Zinc chromate primer of approved make all as per specifications, drawings and as directed by the Engineer in charge

Providing and fixing at all levels MS bolts including nuts and washers of approved size, quality and make as per requirements and as per specifications, drawings complete all as directed at site by the Engineer in charge

Providing and fixing hand rail using 304 grade Stainless Steel pipes /plates etc. of approved size and make and quality by welding, mirror / matt polishing, fixing at site etc. for balcony railing & staircases railing including special sections as per drawings, specifications. complete as directed by the Engineer-in-charge

Provding and constructing brick work in Cement mortar using standard bricks of approved class/ quality, make or brand in foundation and plinth including curing, raking out joints, simultaneous pointing below plinth level if specified, complete as per drawings, specifications and as directed by the Engineer-in-charge

Brick work in C.M 1:4 using crushed sand.

Providing and constructing Random Rubble masonry using approved Rubble stone in foundation and plinth in C.M 1:6 (using crushed sand) including raking out joints or simultaneous flush pointing below ground level / plinth level, curing etc. complete as per drawings and specifications.

Supplying , cutting to shape and fixing specified diameter UPVC pipes as per IS 4985 in RR Masonry/ RCC walls for weep holes complete all as per drawings and as specified at site.

110 mm dia UPVC Pipes

Providing 20 mm thick water proof plastering in cement mortar 1:3 (using crushed sand) finsihed smooth with a floating coat of neat cement including approved water proofing compound added @ 2% by weight of cement or as per manufacturer's specifications, sieving of sand to required fineness, preparation of surface, scaffolding at all heights, curing all as per specifications, drawings and as directed at site.

Providing Raised and cut pointing on stone with cement mortar 1:3 using crushed sand as per specifications and as directed at site by the Engineer-in-charge.

Providing and laying chequered / patterned tiles 300 X 300 mm X 30 mm thick of approved make including levelling, curing, finisihing and cleaning etc. complete to obtain required finish complete on 20 mm thick bed of cement mortar 1:4 (using crushed sand) as per specifications and drawings complete as directed by the Engineer-in-charge

Supplying, stacking and laying of 230 mm thick rubble soling stones as under floor base including packing with smaller stone and compacting, ramming including spreading and consolidation of blinding material, moorum etc. complete all as per specifications and as directed by the Engineer-in-charge

Providing and fixing Glazed VITRIFIED floor tiles of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge

Using Tiles of size 600 X 600 mm

Providing and fixing 75 mm thick Non Asbestos Fiber Reinforced Aerated Cement Sandwich wall panels of bulk density of 876 kg/cum of approved manufacturers , made out of Light Weight Fiber Reinforced Aerated Cement Concrete Core Composed of Portland Cement, Fly Ash Binders Etc. and 4 to 5 mm thick Non Asbestos Fiber Cement Boards on either Side of the Core having a Tongue and Groove on Longitudinal side of the Modules . These panel Modules are Erected / Installed using Galvanised Iron Steel Tracks of suitable section as per manufacturers specification at bottom and Top of the Wall respectively Including all Necessary Material Required for Erecting and Fixing the Wall Panel Complete as per the Direction of the Engineer in Charge. For Permanent and Exterior Joints the Paste of Sodium Silicate and Fly Ash / Cement to be Applied at Tongue and Groove Interlocking Joints and on Exposed Joints with Acrylic Putty and Fiber Tape on Both Side all as per design, drg and specification and as directed by Engineer-in-Charge. (Structural steel used for support if any required shall be paid in relevant item) { Note: Necessary cut-outs for Doors & Windows shall be made in the wall paneling. The rate shall be inclusive of all materials & Labour required for making cut-outs and additional GI channel frame work. No deductions will be made for the cut-outs for measurement purpose.}

Providing and Fixing column encasement which includes fixing of one layer of 9mm thick (High Pressure Steam Cured) Heavy Duty Fiber Cement Board confirming to IS 14862: 2000 Type A Category IV are screw fixed on MS Square Hollow Section frame of size 25 x 50 x 2mm or as specified with 38mm fully threaded self drilling self tapping countersunk fiber cement screws at 300mm c/c to form the MS grid maximum of 610 x 610mm. Finally the square and beveled edges of the board are to be jointed and finished so as to achieve flush seamless finish, which includes special Jointing Compound & Joint tape as per the recommended practices of manufacturer's specifications and as directed by the Engineer-in-charge..

Supply and fixing of Fiber cement Board with accessories Note :- Structural steel will be paid in relevant item.

Providing and Fixing Chajja which includes fixing of one layer of 12mm thick (High Pressure Steam Cured) Heavy Duty Fiber Cement Board confirming to IS 14862: 2000 Type A Category IV are screw fixed on MS Square Hollow Section frame of size 25 x 50 x 2mm or as specified with 38mm fully threaded self drilling self tapping countersunk fiber cement screws at 300mm c/c to form the MS grid maximum of size 610 x 610mm. Finally the square and beveled edges of the board are to be jointed and finished so as to achieve flush seamless finish, which includes special jointing compound & joint tape as per the recommended practices of manufacturer's specifications and as directed by the Engineer-incharge.

Supply and fixing of Fiber cement Board with accessories Note :- structural steel will be paid in relevant item.

Supplying, fabricating, testing, transporting, handling and erecting at required positions and levels metal roofing and canopy roofing including flashings and insulation etc. as per approved drawings and design complete as directed by the Engineer-in-charge including all consumables comprising of the following: Double skin insulated standing seam roofing system comprising of 0.50 mm thick colour coated / bare Al-Zinc Alloy coated steel 0.50 mm with overall width of 400 to 500mm by seaming for 100% water tightness on outer face and 0.50 mm thick inner linear sheet with galvalume sheet profile and physical material properties as specified. These sheets shall be fixed on specially reinforced polyamide or acetylate anti friction di electric brackets at every location for permitting unhindered, free sheet movement at all required locations. The profile shall have a special in built drainage joint at side laps to make it fully watertight even in fully submerged condition. It shall have overall depth of 100 mm from horizontal after fixing . The side laps shall be of interlocking type without requirement of any mechanical seamer. Insulation: This shall be comprising of two layers of Rockwool insulation each of 50 mm thick with density of 48 kg / Cu. M. Sub Grit (Top Hat) 1.5 mm thick Glavanised steel hat section fixed to main purlins, above first layer of insulation, to support the aluminium sheets. Inner linear sheet of 0.50 mm nominal TCT of physical material properties as specified. Vapour Control layer : The vapour control layer to reduce the movement of water vapour from inside the building through the roof construction to reduce the risk of condensation shall consists of 3 layer membrane to be laid continuous across its surface shall be fully sealed at laps, perimeters, penetrations to ensure effectiveness & aluminium foil of 0.50mm thick laid over insulation board.

Providing and fixing in position suspended false ceiling using G.I. exposed ceiling suspension system of grid size 600mm x 600mm with main runner 38mm x 24mm, Cross Tee 27mm x 24mm and wall angle 22mm x 24mm. Using 4mm thick ( High pressure steam cured), pre-painted, self-embossed, reinforced designer cement boards (Ivory) of Lake and Hill/Oceanic/Cascade/Electra texture, conforming to IS 14862:2000 Type B Category III, to be placed in a grid of G.I. system duly suspended with 3m dia G.I./M.S bar hanger fixed with steel dash fasteners or iron Purlins from the roof with adjustment clip. The main runners to be secured to structural soffit by hanger @ 1200mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1200mm Cross Tee to be interlocked between main runners @ 600 c/c so as to form 600mm x 600mm or grid. Provide provisions for light fixtures, air conditioning ducts and diffusers, fire alarms, sprinklers or smoke detectors etc. as per the drawing and directions of engineer in charge.

Providing and fixing Minimum 17 mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut Granite of Telephone Black colour for kitchen platforms, vanitiy counters, Wash basin Counters, Door Frames, window sills, facias and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete as directed by the Engineer-in-charge at all levels

Providing and applying white cement based wall putty of approved make over concrete or Plastered surface up to 3 mm thick to get uniform surface free from undulation including cleaning complete all as directed by the Engineer-in-charge

Providing SFMC Micro concrete for Structural members strengthening works including mixing, pouring, curing as per manufacturer specifications and as directed by the Engineer-in-Charge Using 100% SFMC. 1.Protective coat to reinforcement and bond coat over adjacent concrete surface are included in the item.2.Formwork shall be measured and paid under relevant item.

Providing and laying in position bitumen hot sealing compound for expansion joints using approved make.

Providing groove cutting for concrete surface pavement of cutting of size 5 mmX 20 mm deep filling the grooves with bitumestic (Shalitex) compound complete as directoed by E -I-C

Painting road surface marking with Thermoplastic paint hot applied to give uniform finish with Glass beeds / power Topping, on bituminous surface in white / yellow shade including cleaning the surface of all dirt, scales, oil, grease and other foreign material etc complete as directed by the Engineer-in-charge

Thermoplastic paint on bitumen sufaces

Thermoplastic paint on concrete sufaces including primer

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Anodised Aluminium sections (Minimum anodizing thickness of 15 micron)

Extra for colour anodizing

Providing and fixing of good quality equivalent Sliding Window Roller Double Wheel as per requirement with necessary screws etc. complete. as per specifications and as directed by the Engineer-in-Charge

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

With clear float glass panes of 5.00 mm thickness

Providing and fixing film of specified colour & stroode strips of approved width Garware or equivalent approved make on glass doors or similar smooth surfaces as per manufacturers specifications and shown in drawing and as specified

Filling the gap between aluminium frame & adjacent RCC / Brick work / Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete Up to 5 mm depth and 5 mm width

Providng and fixing Aluminium Grill 10 mm thick "DECO GRILLE" make Model No. DG- 102 in natural Silver anodising of min 15 Microns with a opening size of 80 mm x 66 mm and Minimum weight of 3.13 Kg/ Sq.M including providing anfd fixing Suitable 'F' / 'H' section outer frame and mullion fixing with screws complete all as per specifications and as directed at site by the Engineer-in-Charge .Aluminium alloy shall be of 6063-T6 with Yield strength of minimum 6.5 kg/ sq.mm.

Extra for providing Aluminium Grill 10 mm thick with colour anodised by the manufacturer (Champagne, black, Bronze, Gold colours) complete all as per specifications and as directed at site by the Engineer-in-charge

Providing and fixing locks for aluminium sliding window shutters with "GEETAVIN" make as per cat. No. SS-004 (Over all size of 204mm x 23 mm) or approved equivalent quality, make, type all as per specifications complete as directed by the Engineer-in-charge

Providing and fixing FRP door shutters flush door / panelled type with plain colour or wooden veneer finish of approved make, design & colour. made out of 1.5 mm thick FRP skin moulded over wooden frame work of 40 mm wide and required thickness wooden styles and minimum 100 mm wide lock rails and wooden blocks for door stoppers, tower bolts, baby latch, aldrop, handles etc. wherever required and core filled with Polyurethane Foam and fixing with 4 Nos 100 mm (ISI marked) stainless steel hinges with S.S. wood screws

35 mm thick panelled door type of approved colours including the cost of 100 mm ISI marked heavy quality stainless steel butt hinges with necessary screws.

Providing and fixing aluminium aldrops of size 250 X 16 mm ISI marked anodised transparent or dyed to requried colour or shade with necessary screws, bolting from rear side complete as per specifications and as directed by the Engineer-in-charge

Providing and fixing anodised aluminium tower bolts of size 250 X 12 mm ISI marked of approved make, transparent or dyed to requried colour or shade with necessary screws etc.

Providing and fixing aluminium handles 175 mm long Inner grip 125 mm with 12 mm dia rod plate type BOW handles ISI marked of approved make, anodised transparent or dyed to req. colour or shade with necessary screws etc. complete.

Providing and fixing aluminium hanging heavy quality floor door stopper ISI marked with twin rubber stoppers, anodised transparent or dyed to required. colour or shade with necessary screws etc. complete.

Providing and Painting with 1st quality acrylic washable distemper (ready made) with Two coats on new work of approved make and manufacturer and of required shade and colour, including scaffolding, preparation of the surfaces ,etc., including a coat of approved cement primer.as per manufacturer's specifications and as directed by the Engineer-in-charge.

Providing, painting,finishing walls with two coats of anti-algae, weather proof acrylic smooth emulusion paint of approved make with silicon additives on sand face plaster/ plain plaster & concrete surfaes of required shade over new work over a base coat of exterior cement primer including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge.

Providing and Painting two coats of synthetic enamel paint on steel surfaces of approved brand and manufacture to give an even shade over a primer coat.including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and applying wall painting two coats on new work with premium plastic emulsion paint of approved brand to give an even shade, including a coat of approved cement primer, including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-30 grade made with strong vibratory compaction and approved size, shape, design laid in required colour and pattern over and including 50 mm thick compacted bed of crushed sand, filling the joints with crushed sand etc. all complete as -per the direction of the Engineer-in-charge

Providing and laying 80 mm thick factory made cement concrete interlocking paver block of M-35 grade made by block making machines with strong vibratory compaction and approved size, shape, design laid in required colour and pattern over and including 150 mm thick compacted bed of stone dust / Murrum, filling the joints with crushed sand etc. all complete as -per the direction of the Engineer-in-charge

Providing and Fixing in position 6 mm thick solid clear (Translucent) Polycarbonate sheet of approved make including cutting, fixing on existing supports by Replacing damaged panels and sealing the joints with silicon sealent with necessary stainless steel fastners, scafffolding if necessary complete all as directed by Engineer in charge.

Providing and Fixing Anchor Fastner of approved make including drilling in concrete as per requirement for fixing Eps or other structures all as specified by the manufacturer complete all as per specifications and drawings.

16 MM diameter 200 mm Long

Providing and laying non pressure NP2 class RCC Hume pipes of approved make, with collars jointed with stiff mixture of cement mortar in the proportion of 1:2, laying to the levels, slopes and as per the drawings and specifications and as directed by the Engineer-in-charge including testing of joints etc. complete.

150 mm Dia RCC Hume pipe class Np2

450 mm Dia RCC Hume pipe class Np2

600 mm Dia RCC Hume pipe class Np2

Providing and fixing 6 mm thick mirrors of size 600 x 450 mm of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete. all as per specifications and as directed by the Engineer-in-charge .

Providing and fixing C.P brass towel rail of approved make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in-charge.

Providing & Fixing 304 Grade Stainless steel wire fabric mesh 30 Swg thick & 625 Holes per Sq. Inch for windows/ ventilators etc. beading will be paid seprately.complete all as directed by the Engineer Incharge.

Designing and installation of pre fabricated fixed and folding type Awning - manually operated Cantilever type of approved make and shade for Protection for all outdoor areas, for protecting doorways, pathways, stairs and windows from the sun and weather and Manufactured with welded powder coated steel frames and weather resistant durable fabrics as per specifications and drawings complete as directed by the Engineer-in-charge. (For measurement purpose two feet extra in both the direction to be consider for payment purpose from actual size of awing)

Providing, hoisting and installing at required elevation moulded HDPE cylindrical vertical water storage tanks of approved make of the following capacities with suitable S. M. C cover at top including the cost of labour for making hole in the storage tank for inlet, outlet, scour and overflow, providing and fixing necessary G.I Nipples ranging from 15 mm to 50 nn n.b of average150 mm length with double check nuts, washers etc. complete as directed by the Engineer-in-charge

HDPE CYLINDRICAL vertical storage water tank 1000 lit capacity

Providing and supplying of Truck of minimum capacity 09 MT for the collection and transportation of scrap items, unserviceable equipments, furniture,debris, garbage at various location inside BARC Trombay, Mumbai as instructed by Engineer Incharge.

Providing and supplying Forklifts 03MT capacity for the collection and transportation of scrap items, unserviceable equipments, from various location inside BARC Trombay, Mumbaias instructed by Engineer Incharge.

Providing and supplying Hydra crane 08 MT capacity for the collection and transportation of scrap items, unserviceable equipments, from various location inside BARC Trombay, Mumbai as instructed by Engineer Incharge.

Providing, supplying "JCB" loader cum excavator including operator and helper executing the work like excavation, grading, levelling, debris cleaning and other works at various location inside BARC Trombay, Mumbai all as directed by Engineer Incharge as and when required.

Providing and supplying of Dumper for the collection and transportation of scrap items, unserviceable equipments, furniture, debris, garbage at various location inside BARC Trombay, Mumbai as instructed by Engineer Incharge.

Supplying man power along with necessary spades, shovels, punjas, ropes, small special spades, rain coats, broom, mop etc, minimum two labours per day and maximum any number of labour as and when decided by Engineer Incharge to work for eight hours per day to carry out the cleaning work, loading work etc as directed by Engineer Incharge.

Lead charges for lead Exceeding 3 KM but not exceeding 4 KM, by mechanical transport including loading, unloading, stacking / levelling etc.

Debris Beyond 3 Km but up to and including 4 km

Supplying, fabricating and delivering and fixing at site MS anchor bolts as shown in drawing or as directed by Engineer-in-charge, including nuts/lock nuts, anchor bolt assemblies etc. complete.

Dismantling Bituminous road including stacking of serviceable materails and disposal of unserviceable materials within 200 m lead

Bituminous Road

MARUTI ENTERPRISES