8149/2023-24 PROVN OF MULTI SECTION SHED (WELDING SEC AND ARMR SEC) AT FRI, HQ UNIFORM FORCE AT KIARI UNDER GE 860 EWS

Amount

Surface dressing n exc 15 cm deep in Hard/dense soil, complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard /dense soil, complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers soils not exc 25 cm complete all as specified and directed.

M & L for Plain Cement concrete type D-2 1:4:8 (40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded crushed stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded crushed stone aggregate as in Chajjas complete all as specified and as directed.

Use and waste of Steel sheet form work to sides of concrete foundations, footings, bases of columns raft and beams sides and soffits (if any) of foundations and plinth,beams and similar work,vertical or to batter, for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste of steel sheet form work to sides of pillars, posts, struts, piers, columns and stanchions, for square, rectangular or poygonal, rough finished surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete complete all as specified and as directed.

S & F Mild steel bars 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and directed by Engr in charge.

M &L mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, cut to length, bent to shape required, including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clip complete all as specified and as directed.

M & L Precast cement concrete block masonry type C1 1:3:6 (20mm graded crushed stone aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as Specified.

S & F Mild steel work in roof trusses (framed ) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee,angle,channel or flat sections) including distance pieces cleats etc conforming to Fe-410 complete all as specified and directed.

S&F for 0.50 mm thick Pre- painted galvatume aluminum zinc coating GI based corrugated in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as directed by Engr-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheeting 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/J hooks and bolts as reqd and specified

M&L Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes etc. with riveted, bolted or welded attachment confirming to Fe 410-W (Gde E-250), complete all as directed by Engieer-in-charge.

Mild steel bolts neck exc 10 mm dia and n exc 15 mm dia, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each scre-wed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long, complete all as specified and directed.

M & L for Hardcore of gauge n exc. 63 mm, (broken stone or boulders) deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L for Plinth protection 75 mm thick in PCC type C-1 1:3:6 (using 20 mm graded aggregate crushed stone aggregate) laid in alternate bays (not exc 2 Sqm each) finishing even smooth at top without using extra cement and providing joints throughout the thickness of plinth protectio, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as specified and directed at site complete all as specified and directed.

M&L for Plain Cement Concrete type D-2, 1:4:8 (20 mm graded aggregate) 100mm thick as Sub base complete all as specified and directed.

M&L for 40mm thick Plain Cement Concrete type B-1, 1:2:4 (20 mm graded crushed stone aggregate) as in floor finishing with smooth surfaces complete all as specified and directed.

S&F for 2nd Class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified ans as directed.

S & F 30mm thick Second class hard wood Glazed and skeleton windows,ventilators open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc.sizes of members of shutters as specified in SSR Part I, Section 8 Clause 8.24(a) complete all as specified and directed.

S & F 3.00 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, all as specified.

M & L PCC type B-1 1:2:4 (20 mm graded crushed stone aggregate) for fixing hold fast complete all as specified and directed.

S & F Mild steel flat iron of size 25x3 mm as in hold fast conforming to Fe 410-0 or Fe-310-0 complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster in cement mortar 1:6 on brick or concrete surface etc. on wall finished even smooth without using extra cement, all as specified.

M&L for Rendering 15 mm thick on fair faces of brick wall or cement concrete surface in cement mortar 1 :4 finished even smooth without using extra cement, all as specified.

S & F of 100 mm size extruded alluminium alloy with galvanised mild steel hinge pin type C-21, complete all as specified and directed.

S & F Aluminium anodised, barrel tower bolts of extruded section with 150 mm long bolt and fixed all as specified

S & F Aluminium handles, cast type, anodised 125 mm size complete all as specified

M&L for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paints over a coat of red oxide primer complete all as specified and directed.

Preparing plastered new surfaces of wall and applying two coats of cement base paint with one coat of primer all as specified.

Preparing of new surface of wall of any description and applying three coat of white wash all as specified and as directed.

Prepration of new wooden or wood based Surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified.

S & F Steel rolling shutters size 3m x 3m, thickness of laths 1.25 mm, without ball bearing, as specified including top cover, anchoring rod, pully, necessary ball bearings, oil and greasing, hasp and staple, safety lever locks with 4 levers and one shop coat of primer; erected in position as indicated, complete, gear opereated type with bevel gear box and crank handle including 2 coats synthetic enamel paint, complete all as specified and directed..

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 16 Sqmm, 4 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge

Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 15cm after laying, streching & testing of cable in trenches complete all as specified and directed by Engr-in-Charge. Note :- Only punned thickness i.e 18cm shall be measured and paid.

M&L for point wiring in casing in caping including all fittings with 1.5sqmm size multi stranded FRLS copper conductor cable including clamps , screws gutti/plug etc PVC unsheathed cable into and including PVC box for mounting of switces and PVC insulated FRLS cable of size 1.5sqmm as earth continuity conductor for one light point or one fan point controlled by one, one switch complete all as specified and as directed by the Engineer-in-Charge.

All as per srl item no. 43 here-in-before but for one socket outlet 3 pin, 5 Amps on independent board.

All as per srl item no. 43 here-in-before but for one socket outlet 3 pin, 5 Amps on same board.

All as per serial item No 43 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing switch piano flush button single pole one way 5 Amps complete all as specified and as directed.

Supply and fixing socket 2 in 1, 5 Amp, flush type complete all as specified and as directed by Engr-in-charge.

Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5A/16A, 5 in 1 flush type complete all as specified and as directed by Engr-in-charge.

Supply and fixing angular lamp holder, PVC/Polycaronate type with back plate suitable for 9/12 watt LED bulb complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing LED light bulbs of 12 Watt complete all as specified and as directed

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing LED batten lights fitting 1x 20W, 220V,AC decorative type including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F DB, Single Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.

Supply and fixing MCB single pole and neutral 32 to 40 Amps , 240 volt, 10 KA, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing MCB single pole 5 to 30 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing new energy saving LED Bulk head fitting 10 watt made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK07 as reqd to be mounting bracket in wall/floor to suit the opening of the fitting with FI clamp, nut, bolt and washers of suitable size including making connection complete all as specified and as directed by Eng-In-Charge

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 2009 Part-I and connecting to CBDB’s as specified or indicated including testing on completion .

THINLES OTZER

M/S Web Company

M/S SONAM RIGZIN

M/S GLOBAL ENGINEERS

M/S MA CONSTRUCTION Co

M/S MUNEER HASSAN AKHON

M/S BHAT ENGINEERS