BEAUTIFICATION WORK OF SHRI DIGAMBAR JAIN TEMPLE (SHRI DIGAMBAR JAIN ATISHAY SHETRE MANDIR SANGHI JI) LOCATED IN WARD NO. 51 OF SANGANER ZONE.

(BSR (Civil) 2022, Item No 1.8) Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils

(BSR (Civil) 2022, Item No 1.25) Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift.

(BSR (Civil) 2022, Item No 1.34) Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable concentrate of 20%

(BSR (Civil) 2022, Item No 1.36) Diluting and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRE-CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment and excluding the cost of chemical emulsion) .

(BSR (Civil) 2022, Item No 3.1.4) Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

(BSR (Civil) 2022, Item No 11.26) Random rubble dry stone Kharanja under floor.

(BSR (Civil) 2022, Item No 4.1) Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix

(BSR (Civil) 2022, Item No 4.3) Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix

(BSR (Civil) 2022, Item No 4.9) Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc.

(BSR (Civil) 2022, Item No 4.10.2) Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc.

(BSR (Civil) 2022, Item No 4.6+4.6.1) Add extra for providing richer mixes respectively at all floor levels.Providing M-25 grade concrete by using cement as per codal provision instead of M-20 grade design mix.

(BSR (Civil) 2022, Item No 4.13.3) Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786)Thermo-mechanically Treated bars (Conforming of relevent IS code)

(BSR (Civil) 2022, Item No 5.16.2) Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor V level in. Cement mortar 1 : 6 (1 cement : 6 coarse sand)

(BSR (Civil) 2022, Item No 5.19.1) Half Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor V level in. Cement mortar 1 : 4 (1 cement : 4 coarse sand)

(BSR (Civil) 2022, Item No 6.1.6) Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 (1-Cement:6-Sand).

(BSR (Civil) 2022, Item No 3.7.2) Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification . 75mm thick.

(BSR (Civil) 2022, Item No 8.13.2) Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' :30 mm thick .Commercial Veneer both side

(BSR (Civil) 2022, Item No 8.35.2) Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails complete as per approved by engineer in charge.0.8mm thick mica

(BSR (Civil) 2022, Item No 9.6.1) Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-in-charge : Profile B

(16.19) Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in-Charge.

(16.18) Providing and fixing to existing door frames 30mm thick factory made polyvinyl chloride (PVC) door shutter made of stiles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2mm +/- 0.2mm with inbuilt decorative moulding edging on one side. The stiles and rails mitred and joined and the corners by means of M.S.galvanized/plastic brackets of size 75x220 mm having wall thickness 1.0mmand stainless steel screws. The stiles of the shutter reinforced by inserting galvanized M.S.tube of size 25x20 mm and 1mm +/- 0.1mm wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30 mm and 2mm +/- 0.2mm wall thickness fixed to the shutter stiles by means of plastic/galvanized M.S.tube ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 610mm,having overall thickness of 20mm and 1mm+/- 0.1mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6mm galvanized M.S.rod and fastened with nuts and washers.complete as per manufacturer’s specification and direction of Engineer-in-charge.(For W.C.and bathroom door shutter)

(BSR (Civil) 2022, Item No 16.1.1.2) Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). For fixed portion. Powder coating aluminum ( minimum thickness of powder coating 50 micron)

(BSR (Civil) 2022, Item No 16.1.2+16.1.2.2) For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). Powder coating aluminum ( minimum thickness of powder coating 50 micron).

(BSR (Civil) 2022, Item No 16.2) Extra for shutters of sliding aluminum windows

(BSR (Civil) 2022, Item No 16.5.2) Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item.) With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm)

(BSR (Civil) 2022, Item No 16.10.2) Providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminum window/vent with required screws, Y and H aluminium section (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge. Powder coating aluminum ( minimum thickness of powder coating 50 micron)

(BSR (Civil) 2022, Item No 10.17.1) Grading roof for water proofing treatment with water proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

(BSR (Civil) 2022, Item No 11.18.2) Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) For area of each slab from 2001 to 5000 Sq.Cm

(BSR (Civil) 2022, Item No 11.19+11.19.1) Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

(BSR (Civil) 2022, Item No 12.3.3) Plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine finish :12mm thick.

(BSR (Civil) 2022, Item No 12.3.2) Plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine finish :20mm thick.

(BSR (Civil) 2022, Item No 12.5) 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand)

(BSR (Civil) 2022, Item No 12.40.1) Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect.

(BSR (Civil) 2022, Item No 12.22.1) Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete.New Plastered Surface (three or more coats)

(BSR (Civil) 2022, Item No 7.12) Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar).

(BSR (Civil) 2022, Item No 7.13) Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).

(BSR (Civil) 2022, Item No 7.14) Extra for using Marble printed / Granite shade or dark shade tiles instead of white, grey, ivory, fume red brown, light green, light blue and other light shades in glazed tiles

(BSR (Civil) 2022, Item No 7.14) Extra for using Marble printed / Granite shade or dark shade tiles instead of white, grey, ivory, fume red brown, light green, light blue and other light shades MAT finished tiles

(BSR (Civil) 2022, Item No 7.15) Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm size.

(BSR (Civil) 2022, Item No 7.15) Extra for using size 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size.

(BSR (Civil) 2022, Item No 16.56 (a)) Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).Grade 304

(BSR (Civil) 2022, Item No 11.12) Crazy marble stone flooring 20mm thick marble stone with black or of specified colour topping including filling the gaps with cement marble chips mix in proportion of 4 : 7 (4cement : 7 white black or white or black marble chips) size from 1mm to 4mm by volume and under layer of 25mm thick cement concrete [1:2:4, graded stone aggregate 12.5mm nominal size] rubbing and polishing and cement slurry etc. complete : In ordinary cement.

(1.2) P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor:

(1.2.2) Size 580x440mm.

(1.14) P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete.

(1.14.2) Flat Back (large) or half stall size 610x400x80mm.

(1.16) P&F Marble Urinal Partition slab both sides polished of approved design cut from marble size 900x600mm.

(1.16.1) Makrana II quality marble having light spots

(1.2) P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball (IS: 1703 mark) complete including cutting and making good the wall:

(1.20.2) PVC with PVC bend as per IS : 7231.

(1.29.1) P & F C.P. brass Urinal Spreader for stall urinal of approved make.

(1.36) P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall :

(1.36.8) Size 550 mm x 400 mm dia for counter top

(1.38) P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor :

(1.38.9.4) 37 x 18 x 7 17x15x7 (with drain board)

(1.41) P & F Bottle Trap of approved make :

(1.41.1) C.P Brass 32 mm

(1.44) P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers.

(1.44.1) Size 600 x 450mm x 4 mm thick

(1.48) P & F Grating of approved quality/make:

(1.48.2) Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make

(1.51) P & F Toilet Paper Holder with rod of approved quality/make:

(1.51.2) C.P. brass heavy & Superior quality.

(1.52) P & F Soap Dish or Tray of approved quality/make

(1.52.2) C.P. brass heavy and superior quality.

(2.12) P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc.

(2.12.1) C.P. Inlet connection 15mm.Brass (IS : 8931 marked)

(2.13.3) P & F 15 mm. Dia Connection Pipe of approved quality/make :PVC pipe with C.P. Brass nuts upto length, 300mm (-do-) 450mm.

(2.7) P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:

(2.7.3) C.P. Brass bib cock,15mm nominal bore.

(2.7.4) (-do-) Long body, 15mm nominal bore weight not less than 690 gm

(2.7.6) (-do-) Elbow-action, 15mm nominal bore.

(2.6.4) C.P. Pillar cock, Swan-neck with casted spout, 15mm nominal bore.

(2.33) Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge

(2.33.9) Concealed stop cock 15 mm nominal size

(2.37) Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall)

(2.37.3) 25 mm nominal size

(2.37.4) 32mm nominal size

(2.37.5) 40 mm nominal size

(2.38) Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,)

(2.38.2) 20mm nominal size

(2.38.3) 25 mm nominal size

(2.15) P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :

(2.15.3) (-do-) 25mm nominal bore.

(2.15.5) (-do-) 40mm nominal bore.

(3.44) Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make

(3.44.1) 75 mm dia

(3.44.2) 110 mm dia

(3.45) Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make

(3.45.1) Coupler

((i)) 75mm dia

((ii)) 110mm dia

(3.45.4) Bend 87.5 Dg.

((i)) 75mm dia

((ii)) 110mm dia

(3.45.5) Bend 45 Dg.

((i)) 75mm dia

((ii)) 110mm dia

(3.45.6) Door Bend 87.5 Dg.

((i)) 75mm dia

((ii)) 110mm dia

(3.45.7) Single 'Y'

((i)) 75mm dia

((ii)) 110mm dia

(3.45.16) Single Tee

((i)) 75mm dia

((ii)) 110mm dia

(3.45.11) Socket Plug

((i)) 75mm dia

((ii)) 110mm dia

(3.45.12) Pipe Clip

((i)) 75mm dia

((ii)) 110mm dia

(3.45.17) Single Tee with Door

((i)) 75mm dia

((ii)) 110mm dia

(3.45.25) Nahni Trap with Jali 4”

() 110mm dia

(3.45.30) Vent Cowel

() 110mm dia

(3.16) P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant.

(3.16.3) 110 mm dia

(3.8) Providing, Laying & Jointing R.C.C. class NP-2 Non-Pressure pipes (IS : 458mark) of approved make with collars, jointed with C.M. 1:2 or having Spigot and socket ends with flexible rubber rings joint including testing of joints etc. complete :

(3.8.2) 150mm dia Internal

(3.16.4) P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant.160 mm dia

(3.16.5.2) Providing & Laying C.C. 1:3:6 (Stone Agreegate 20mm nominal size) all around PVC Pipe including 7.5 cm thick bed concerte [Width & Height = Dia of Pipe in CM+15CM] excluding cost of Pipe & Excavation of trenches etc.

(3.17.1 (iii)) Coupler (socket) 160 mm

(3.17.9 (iii)) Bend 87 .5 160 mm

(3.5) P & F Square-mouth gully trap `A` grade (IS 651-1992 :marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type.

(3.5.1) Trap size 150 X 100mm, ferrow cement cover with frame, Internal Chamber size 300 X 300mm.

(3.21.2) Inside size size 450 x 450mm depth upto 0.5 M Cement cover with frame

(3.24) Construction of Soakage well in all types of soil of approved drawing, top 90 Cm .Portion in 450mm thick masonry with CM 1:6, 80 mm thick stone slab covering, jointing of slab in CM 1:3 ,Ralthal, kharanja 40mm thick M-15 grade C.C flooring, earth work etc . complete including disposal of surplus earth within a lead of 50 mtr .

(3.24.1) Inner dia 90 Cm & 10 to 12 Mtr deep.

(3.27.3) Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:- Size 400 x140x150 cm.(for 50 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 10mm ϕ @15 cm c/c bothways including shuttering complete in all respect.

(3.35.3) Construction of open Drain with 112mm thick brick masonry in CM 1:4 Semi circular S.W. glazed channel (confirming to IS Standards) fixed with cement mortar 1:1 over a bed of 100mm thick C.C. 1:5:10, filling of edged with M-15 grade C.C. flooring, 12mm cement plaster 1:4, over all exposed faces, excavation & disposal of earth with in a lead of 50 mtr complete as per approved drawings :250 mm drain,225mm Av. depth width 25 Cm S.W. glazed channel.

(2.26) P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design:

(2.27) Hoisting Charges for each floor :

(2.27.2) For items 2.26.5 to 2.26.8

(1.8) Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils

(3.1.4) Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

() POINT WIRING AND SUBMAIN WIRING

(1.1) Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07

(1.1.1) Short point (up to 3 mtr.)

(1.1.2) Medium point (up to 6 mtr.)

(1.1.3) Long point (up to 10 mtr..)

(1.2) Wiring of twin control light point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 2 Nos Hot Dipped Galvanized M.S Modular box of 1.2 mm thick with earth terminal,2 Nos10 A two way Modular switch, 3 pin ceiling rose / holder / 3 way connector ,Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07

(1.3.3) Medium point (up to 6 mtr.)

(1.3) Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07

(1.3.1) ON Board

(1.3.2) Short point (up to 3 mtr.)

(1.3.3) Medium point (up to 6 mtr.)

(1.3.4) Long point (up to 10 mtr..)

(4.1) Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires.

(4.1.3) 3x 1.5 sq.mm (For Extra Point Wiring)

(4.1.7) 2 x 2.5 sq. mm. + 1x1.5sqmm (For Light & emergency circuit)

(4.1.14) 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. (For Power & AC Circuit)

(4.1.18) 4 x 6.0 sq.mm (For Sub Mains)

(4.1.10) 1 x 4.0 sq.mm (For Earthing)

(5.7) P & F P.V.C. sheet 2.0 mm thick of following size Including screws, cup washer as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

(5.7.2) 100 mm dia.

(7.37) Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification of Wiring accessories refer Chapter E - 07 related item.

(7.29) Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required.

(7.29.1) 5 step fan regulator 2 Module 360 dgree rotating

(7.28) Providing & Fixing of modular type lockable feature socket duly made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. NOTE- ONLY COMPUTER POINTS SET.

(7.28.1) 6 A 3/5 pin shuttered socket

(7.28.2) 6/16 A shuttered socket

(7.31) Providing & Fixing of following size mounting grid plates with cover plates made from fire retardent UV established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.All as per pre approved by Engineer in charge. NOTE- ONLY COMPUTER POINTS SET.

(7.31.1) 1/2 Module

(7.31.6) 8 Module

(7.32) Providing & Fixing of Wiring Accessories OEM fabricated following size GI box of 1.2 mm thick with earthing terminal and adjustable floating clamp in recess/ surface suitable for modular accessories as required.All as per pre approved by Engineer in charge. NOTE- ONLY COMPUTER POINTS SET.

(7.32.1) 1-2 Module

(7.32.4) 6 / 8 module

(1.4) S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required.

() MCB'S & DISTRIBUTION BOARDS

(6.1) Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.

(6.1.1) Single pole MCB (With B/C curve tripping Characteristics)

(6.1.1.2) 6 A to 32 A rating

(6.1.2) Double pole MCB(With B/C curve tripping Characteristics)

(6.1.2.4) 50/63 A rating

(6.3) Providing & Fixing of 240/415 V factory fitted RCBO with overload, short-circuit and earth leakage protection with ISI marked (IS12640-2)/ conforming to IEC 61009-1, breaking capacity 10 KA, provision for pad lock, min. Electrical operation 10,000 upto 63 A rating , minimum phase termination capacity of 35sq.mm. , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.

(6.3.2) Two pole 100/300mA sensitivity

(6.3.2.1) 6A-32 A rating

(6.1) Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.

(6.10.3) Metal door (Three phase) IK-09 and IP-43 with Metal end box

() FANS & LIGHTINGS

(15.7) Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.

(15.7.3) 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 )

(5.9) P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge.

(15.6) Providing & Fixing of 400 mm Sweep BLDC technology Oscillating type Wall mounting / Pedestal type fans with Three speed, ON and OFF position, Double Wall bearing with front and back 120 or more ribs guard; Three no. blades, noise level should be <= 75 dB, including fixing with anchor bolts, making connection testing etc. as required. ( With Remote ) All as per pre approved by Engineer in charge.

(15.6.1) Wall mounting type with Service value 2.0 CMM /W, Min. Air Delivery 71 CMM

(15.12) Providing & Fixing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400 RPM single phase Exhaust fan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge.

(15.12.1) 300 mm sweep(900/1400 RPM)

(17.1) Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge.

(17.1.1) 1170mm(+/-10%) LED batten with min. lumen output 2200 lm

(17.3) Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / Sqaure SMD Mid Power LED Downlight with power coated die-cast aluminum housing with UV Stabilized non yellowish Diffuser with BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% . System Lumen efficacy of ≥ 110 lm / watt, THD < 10 % , Pf.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

() Recessed Mounting

(17.3.1.5) Minimum lumen output 1950 lm

(17.3.2) Surface Mounting

(17.3.2.3) Minimum lumen output 1950 lm

(17.4) Providing & Fixing of IP20, 2'x2' LED Surface/ Recessed mounting Mid power SMD type LED Light fixture not less than 50mm housing depth made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 4 KV internal/ external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

() OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. All as per pre approved by Engineer in charge.

(17.4.1.3) Minimum lumen output 4200 lm

(17.9) Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb in existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge.

(11.3) Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured Copper cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

(11.2) Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.

(12.12) P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24, Stiffness Class 750 N, Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of Earth & Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in charge.

(6.16) Providing & Fixing of Recessed/surface mounting heavy duty Vertical TPN Distribution board with Metal end box with provision of incomer suitable for 3/4 pole MCCB and SP / TP MCB as outgoing ,made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powder painted with reversible door (for double door DB only ) complete with insulated 160 (upto 160 A Incomer) / 250 Amp. copper bus bar, neutral bars with shrouds, earth bar , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.

(6.1) Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.

(6.1.1.2) 6 A to 32 A rating

(6.1.3) Triple pole MCB (With B/C curve trippingCharacteristics)

(6.1.3.2) 6 A to 32 A rating

(6.1.3.4) 50/63 A rating

(6.1.4) Four pole MCB (With B/C curve tripping Characteristics)

(6.1.4.2) 6 A to 32 A rating

(6.1.4.4) 50/63 A rating

Percentage BoQ

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (Part-B) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

(RUIDP 9.13) Flooring with Cobble stone of approx. Size 125x125x75 mm (thick) laid on 25 mm average thick cement mortar 1:3 ( 1 cement : 3 Coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the stone, laid in approved pattern complete in all respect as per direction of Engineer-in-charge.

(RUIDP SOR 2023 76.1) Supply, installation testing and commissioning of MNRE approved Grid tied Solar Panels with inverter, meter, cable etc. suitable for Rooftop installation as well as Unility Scale Solar Power Projects with 25 years of linear generation warranty, Work includes designing of solar panel area and MS frame and foundation on ground/roof of Pump house or CWR, showing arrangement of panel in available space. Installation of PV module on MS frame as per approved design and drawings. Mounting structure shall be suitably designed to withstand wind velocity up to 150km/hr. Grid Tie Transformer less inverters, Multiple independent MPPTs, Peak efficiency of >98%. Connect up to multiple strings PV arrays. Easy & fast connection, Built in string level monitoring, IP 65 protection level, Wi-Fi/ internet based remote monitoring with 5 years warranty. All cabling up to panel and metre, earthing etc. required accessories and taxes are inclusive. The work shall be executed as per detailed technical specifications, approved drawing and direction of Engineer in-charge. Note: There shall be 5 year service warranty for panel, inverter meter, cable etc, and suitable provision shall be included in tender document

(76.1.2) far panels more than 10 KW and up to 50 KW at a single location,

Item Rate BoQ

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (Part-C) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only) (NBSR)

NUMBER #

Providing/Carving/Fixing of placing of Dustbin in Bansi Paharpur stone with Carved Arch pattern and wire mash litter bin inside , over all size of dust bin will be 900x900x1200 as per detail drawing and as directed by engineer incharge complete in all respect.

Providing,carving and Fixing of interpretive signages in Bansi paharpur stone of size 1000x1300x50 mm on inclined plane .Engraving,painting of latters as per drawing and design.The signage stone shall be fixed on the post of same stone of size 300x 300 x 1050 above ground and 1/3 of total heigt of post shall be embedded in ground with neccesary earthwork and concreting etc.complete as per details and drawings and as directed by engineer incharge.

PERFICIENT Storage Type Water Cooler 40 LPH Cooling Capacity PERFICIENTR (PERFICIENT 40 SS) Cooling Capacity Rating of Water Cooler (In LPH) 40, Type of Pressure Water Cooler Faucet Type, Cooler which store or cool water in the same container,Storage unit material as per clause no 6.8 of IS 1475 (Part 1) / Storage type unit as per clause no. 5.9 of IS 1475 : 2024 Stainless Steel 304, Refrigerant properties As per Clause No. 6.5 of IS1475 (Part 1), Number of Faucets 2, Type of Compressor Reciprocating, Three-core cable conforming to IS 9968 (Part 1) or IS 694 of at least 1.5 meters As per Clause 6.16 of IS 1475 (Part 1), Storage Capacity for Storage Type Water Coolers (In Liters) 60

Facade Illumination (100 M* 10 m)

SITC of Decorative LED post top lantern (approved by department) System power consumption 90W(nominal), Color temperature 3000K(WW)/5700K(CW), Color rendering index(CRI) ≥70. Fixture should be designed with a classic look and using new generation technology in LED to enliven your outdoor areas in perfect synchronization with functionality and aesthetics. Family of post-top lanterns designed to compliment the geometry of the area with heritage touch. Operating temperature: 50 °C. Operating voltage range: 140 V - 270 V. Average life L70B50: 50000 hours. Housing should be elegantly designed pressure die casted heat sink for efficient thermal management and sturdiness. Luminaire finish should be UV protected pure polyester powder coated grey with phosphochromate treatment. Luminaire should be with PC lens to ensure better uniformity of light distribution. High efficiency long life LED module with SMD LED package mounted on MCPCB. Led Lumen efficacy of LED >140 lm/W and viewing angle of 120° to ensure better uniformity. Total System Lumens 10800 lm/System lumen 120 lm/watt(Nominal).Fixture should be THD≤ 10%, Power Factor>0.95, Potted driver,BIS Certified, Fixture dimension should be Dia 540 ±2% mm, height 620 ±2% mm, mounting pole inner dia 41mm ±2%. Fixture should be equipped IK08,IP66 protection rating, Fixture driver should be - Built-in potted electronic LED driver with APFC , Open Circuit Protection, over Voltage protection, Surge Voltage Protection upto 10kV With Built In SPD & other safety test as per 15885 Part-2/Sec 13. Lm79 & LM80 reports, BIS Certificates test reports to be provided from in house NABL Lab with latest Photo-goniometer, Design attached. Make Havells, Lustre illuminations, K-Lite, Transrail,Bajaj

Supply and installation of ornamental decorative casting Pole hot dipped galvanised mild steel step pole with grey powder finish with single arm bracket. Total height of the pole with single arm bracket shall be 6000 mm nominal above the ground & 8000mm inclusive of armbracket. The pole must have two ornamental decorative casting in Golden color made of Pressure Die casting in aluminium at Bottom and middle. The pole shall have window cutting of 300 mm x 100 mm weatherproof flush door & locking arrangement for housing of the pole to accommodate electrical accessorieThe decorative pole shall be duly pre-treated and painted UV resistant coating in Grey color shade. The Pole & the cast iron embellishments should be machined & polished properly to get the smooth finish. The coating should have a DFT of 80-90 microns. three Stage treatment with PU based etch primer,Zinc phosphate primer and Poly Urethane paint 40 microns of approved color & prescribed for such surfaces to make it absolutely rust and corrosion proof, as well as giving it a pleasing appearance,The body of the pole shall be machined and polished properly to give it a smooth surface as per IS 2629 and IS2633 Mild steel base plate with 10 mm thickness, having 4 holes of 20 mm dia at a distance of 225mm. Top 76mm, Bottom, 140 mm, Base Plate 250X225X10 mm. Sturdy design made of 76mm dia GI pipe for pole mounting and 48mm dia GI pile for product installation. Golden knob is provided at the top to enhance the aesthetics of the product.Hot dip galvanised with minimum average GI coating of 35μm. PU(Polyurethane) Painted with avg. thickness of 80μm in Grey color (RAL-7024). The grade of cast iron embellishments shall be FG-220. Length of Arm 1000mm/2000mm. Arm mounting dia 48x76 mm . Design attached. Make:- Havells, Lustre illuminations, K-Lite, Transrail,Bajaj

Please Enable Macros to View BoQ information