REPAIR MAINT OF PUMP MOTORS BORE WELLS LT PANELS AND RAW WATER AND SWIMMING POOL CHEMICALS AND OTHER WATER SUPPLY RELATED MISC WORKS AT BAIRAGARH UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

S&F in copper cable of size 25 sqmm single core, PVC insulated, unarmoured, 440 Volt 50 Hz, draw in PVC conduit including taking out old cable complete all as specified and directed.

All as per item No. 1.00 here-in-before but copper cable of size 35 sqmm.

All as per item No. 1.00 here-in-before but copper cable of size 50 sqmm.

S&F foot valve of 80mm bore, Cast iron body, flange type, ISI marked including nut, bolt all connected fitting including taking down old foot valves complete all as specified and directed

All as per item No. 4.00 here-in-before but foot valve of size 100mm bore.

All as per item No. 4.00 here-in-before but foot valve of size 150mm bore.

All as per item No. 4.00 here-in-before but foot valve of size 200mm bore.

S&F in replacement automatic starter of star delta type in sheet metal enclosure type, wall mounting suitable for centrifugal pump/ submersible pump/monoblock pump, 3 phase, 415 volt, 50 Hz, suitable relay range in 5 to 30 Amp, ML contactor, ML over load relay all including taking out old starter single phase preventer fittngs complete all as specified and directed.

S&F in replacement of MCCB 4 pole, 63 Amp, 36 KA breaking capacity, including suitable size copper lugs and connected fittings, complete all as specified and directed.

Taking out old MCCB & S&F in replacement of MCCB 4 pole, 100 Amp 36 kA breaking capacity, including suitable size copper lugs and connected fittings, complete all as specified and directed.

Taking out old contractor & S&F in replacement power contactor, type ML-4, 3 pole, 415V, 50Hz, 3 Phase with auxilary contacts 2 NL&T complete all as specified and directed.

Taking out old contractor & S&F in replacement power contactor, type ML-6, 3 pole, 415 V, 50Hz, 3 Phase with auxilary contacts 2 NO + 2 NC complete all as specified and directed

S&F in replacement power contactor, type ML-2, 3 pole, 415 V, 50Hz, 3 Phase with auxilary contacts 2 NO + 2 NC complete including taking out all as specified and directed.

S&F in replacement electronic timer for Star Delta Starter type, timing range 3-30 sec, 415 V, 50 Hz complete including taking out all as specified and directed.

S&F in replacement thermal over load relay for Star Delta type, Starter, timing range 5-30 amp, 415 V, 50 Hz complete including taking out all as specified and directed.

All as per item No. 15.00 here-in-before but timing 66-120 amp.

S&F in replacement automatic starter of 50 to 60 hp star delta in sheet metal enclosure type, wall mounting suitable for centrifugal pump of 60 HP, 3 phase, 415 volt, 50 Hz, relay range 60 -110 Amp, ML-6 contactor, ML over load relay all including single phase preventer fittings complete including taking out all as specified and directed.

Taking out old submersible cable and S&F submersible flat copper cable of size 6sqmmX3core , 220 volt , 50 Hz all specified and directed.

Taking out old submersiblle cable and S&F flat submersible copper cable of size 4sqmmX3core , 220 volt , 50 hz all specified and directed.

S&F in replacement DOL starter of relay range 2 to 5 amp in sheet metal enclosure type, wall mounting suitable for , 3 phase, 415 volt, 50 hz, rp, , ML over load relay all including single phase preventer fittings complete including taking out all as specified and directed.

S&F in replacement automatic starter of star delta in sheet metal enclosure type, wall mounting suitable for centrifugal pump/ submercible pump/monoblock pump pump/ vertical turbine pump of , 3 phase, 415 volt, 50 hz, suitable relay range in 70 to 150 Amp, ML6 contactor, ML over load relay all including taking out old starter single phase preventer fittngs complete all as specified and directed.

Supply and fixing chlorine testing kit of range 0.1 PPM to 5 PPM including testing chlorine testing liquid all including taking out old Kit specified and directed

S&F in repair round copper lugs, 25mm dia, complete including taking out all as specified and directed.

All as per item No. 23.00 here-in-before but copper lugs 35 mm dia.

All as per item No. 23.00 here-in-before but copper lugs, 50mm dia.

All as per item No. 23.00 here-in-before but copper lugs 16mm dia.

M&L for cleaning of existing drainage system of Filter Pump House and cutting grass around 3 metre both sides, complete including taking out all as specified and directed.

Supply, fabrication and fixing MS channel /pipe fitting/barrel piece /lateral pipe as per site requirement including nut, bolt, washer, welding etc and fibre board gasket complete and making joint leak proof including including taking out dismantling old structure complete all as specified and directed.

M&L for welding work of size 12 mm consider one welding job including cutting, jointing and all connected accessories all specified and directed.

S&F thermal overload relay with setting range 30-50 Amp, 415V, 50Hz ,3Phase complete set and all as specified and directed.

Supply & replacement of electronic timer for Star Delta Starter type timing range 3-30 sec , 220 volt , 50 Hz all specified and directed.

Supply & replacement of Single Phase Preventor upto 75 HP, 440 volt, 50 Hz all specified and directed.

M&L for submersible pumping set complete with column pipe any capacity and any type from existing bore well carefully without damaging the pump set including connecting parts and lowering the same after repair including provision of suitable size of nut & bolts with washer and suitable packing for column pipes and connection of submersible cable including taking out complete all as directed. NOTE: (1) Chain pully block and clamps etc shall be provided by the contractor. (2) Necessary safety pracaution will be responsibility of the contractor.

Disconnecting/ Dismentling of submersible/centrifual/Monoblock/ pressure pump/Non clog motor Pump/ VT Pump/ open well pump Set assy from its foundation at various place of Bairagarh pump house and transporting to civil workshop for repair complete and taking back after repairing, fixing to its existing position and making all connections. Dismentling and opening of pump assy for checking out defects. Taking out shaft from pump and carrying out lathe work on shaft for checking and making straightness. Taking out of old worn out brass impeller and M&L for filling material on worn out part, grinding, poilshing and carrying out complete lathe work, refixing on shaft and check for its smooth functioning and balancing. Note:-(Parts for following items shall be paid under relevent item here-in-after under as supply).

240 HP motor

50 HP to 65 HP motor

30 HP to 45 HP motor

10 HP to 25 HP motor

5 HP to 7.5 HP motor

1 HP to 3 HP Motor

Taking out unserviceable spares and burnt copper binding wire complete. M&L for rewinding of submersible motor / open well motorwith insulated copper winding wire including sleeves as per original company and replacement of worn out parts, including grinding & polishing of rotor sleeves and refixing, testing & transport charges complete all as specified & directed. Note:- Parts for following items shall be paid under relevent item here-in-after under as supply only.

1 HP to 30 HP Motor

Taking out unserviceable spares and burnt copper binding wire and M&L for rewinding of submersible motor / open well motor with insulated copper winding wire including sleeves as per original company and replacement of worn out parts, including grinding & polishing of rotor sleeves and refixing, testing & transport charges complete all as specified & directed. Note:- Spares Parts for following items shall be paid under relevent item here-in-after under as supply only.

Bowl bush

Impeller

Neck ring

Shaft sleeve

Pump shaft

Coupling

Coupling key

Impeller key

Stud with nuts

Thrust bearing

Lower housing bush

Upper housing bush

Rotor shaft sleave

Drain plug

Water seal

CI Bowl

Bearing Suitable for pump set

Rotor Shaft

Supply and fix the following parts of the submersible /open well pump and motor for capacity between 11 HP to 20 HP of original company as approved complete all as specified and directed. Note :- Unserviceable Parts other than as listed below of Pump if required to be replaced to make the pump functional is to be replaced by contractor. No extra payment shall be paid to contractor.)

Bowl bush

Impeller

Neck ring

Shaft sleeve

Pump shaft

Coupling

Coupling key

Impeller key

Stud with nuts

Thrust bearing

Lower housing bush

Upper housing bush

Rotor shaft sleave

Drain plug

Water seal

CI Bowl

Rotor Shaft

Bearing Suitable for Existing Pump

Supply and fix the following parts of the submersible /open well pump and motor for capacity between 21 HP to 30 HP of original company as approved complete all as specified and directed. Note :- Unserviceable Parts other than as listed below of Pump if required to be replaced to make the pump functional is to be replaced by contractor. No extra payment shall be paid to contractor.

Bowl bush

Impeller

Neck ring

Shaft sleeve

Pump shaft

Coupling

Coupling key

Impeller key

Stud with nuts

Thrust bearing

Lower housing bush

Upper housing bush

Rotor shaft sleave

Drain plug

Water seal

CI Bowl

Rotor Shaft

Bearing Suitable for Existing Pump

Taking out unserviceable spares and burnt copper binding wire complete. M&L for rewinding of submersible motor with insulated copper winding wire including sleeves as per original company and replacement of worn out parts, including grinding & polishing of rotor sleeves and refixing, testing & transport charges complete all as specified & directed. Note:- Parts for following items shall be paid under relevent item here-in-after under as supply).

(a) 1 HP to 240 HP Motor

Supply and fix the following parts of the centrigual Pump and motor for capacity 240 HP of original company as approved complete all as specified and directed. Note :- .U/S Part other than as listed below of Pump if required to be replaced to make the pump functional is to be replaced by contractor. No extra payment shall be paid to contractor.)

Bowl bush

Impeller

Neck ring

Shaft sleeve

Pump shaft

Coupling

Coupling key

Impeller key

Stud with nuts

Thrust bearing

Lower housing bush

Upper housing bush

Rotor shaft sleave

Drain plug

Water seal

CI Bowl

Rotor Shaft

Bearing Suitable for Existing Pump

Supply and fix the following parts of the centrigual /Monoblock / Pressure Pump and motor for capacity between 50 HP to 65 HP of original company as approved complete all as specified and directed. Note :- Unserviceable Part other than as listed below of Pump if required to be replaced to make the pump functional is to be replaced by contractor. No extra payment shall be paid to contractor.

Bowl bush

Impeller

Neck ring

Shaft sleeve

Pump shaft

Coupling

Coupling key

Impeller key

Stud with nuts

Thrust bearing

Lower housing bush

Upper housing bush

Rotor shaft sleave

Drain plug

Water seal

CI Bowl

Rotor Shaft

Bearing Suitable for Existing Pump

Supply and fix the following parts of the centrigual /Monoblock / Pressure Pump and motor for capacity between 30 HP to 45 HP of original company as approved complete all as specified and directed. Note :-Unserviceable Part other than as listed below of Pump if required to be replaced to make the pump functional is to be replaced by contractor. No extra payment shall be paid to contractor.

Bowl bush

Impeller

Neck ring

Shaft sleeve

Pump shaft

Coupling

Coupling key

Impeller key

Stud with nuts

Thrust bearing

Lower housing bush

Upper housing bush

Rotor shaft sleave

Drain plug

Water seal

CI Bowl

Rotor Shaft

Bearing Suitable for Existing Pump

Supply and fix the following parts of the centrigual /Monoblock / Pressure Pump and motor for capacity between 10 HP to 25 HP of original company as approved complete all as specified and directed. Note :- Unserviceable Part other than as listed below of Pump if required to be replaced to make the pump functional is to be replaced by contractor. No extra payment shall be paid to contractor.)

Bowl bush

Impeller

Neck ring

Shaft sleeve

Pump shaft

Coupling

Coupling key

Impeller key

Stud with nuts

Thrust bearing

Lower housing bush

Upper housing bush

Rotor shaft sleave

Drain plug

Water seal

CI Bowl

Rotor Shaft

Bearing Suitable for Existing Pump

Supply and fix the following parts of the centrigual /Monoblock / Pressure Pump /vaccum pump and motor for capacity between 1 HP to 10 HP of original company as approved complete all as specified and directed. Note :- Unserviceable Part other than as listed below of Pump if required to be replaced to make the pump functional is to be replaced by contractor. No extra payment shall be paid to contractor.)

Bowl bush

Impeller

Neck ring

Shaft sleeve

Pump shaft

Coupling

Coupling key

Impeller key

Stud with nuts

Thrust bearing

Lower housing bush

Upper housing bush

Rotor shaft sleave

Drain plug

Water seal

CI Bowl

Rotor Shaft

Taking out unserviceable spares parts and burnt copper binding wire for VT 75 HP/Sewage VT Pump complete and M&L for rewinding of Vertical motor with insulated copper winding wire including sleeves as per original company and replacement of worn out parts including grinding & polishing of rotor sleeves and refixing, testing & transport charges complete all as specified & directed. Note:- Parts for following items shall be paid under relevent item here-in-after under as supply.

Supply and fixing the following parts of the VT Pump and motor for capacity between 75 HP of original company as approved complete all as specified and directed. Note :- Unserviceable Part other than as listed below of Pump if required to be replaced to make the pump functional is to be replaced by contractor. No extra payment shall be paid to contractor.

Bearing

Impuller

Ishpenter Bush

Neck Ring (04 Nos)

Shaft Turning (04 Nos)

Bush (04 Nos)

Rotor Seal

Bowl bush

Neck ring

Shaft sleeve

Pump shaft

Coupling

Coupling key

Impeller key

Stud with nuts

Thrust bearing

Lower housing bush

Upper housing bush

Rotor shaft sleave

Drain plug

Water seal

CI Bowl

Rotor Shaft

S&F in replacement to ON load Change over switch, rotory type 100 Amp, 415 Volt , TPN, front operated without sheet metal enclosure suitable for mounting on existing panel as per sample and site requirement complete all as specified and directed.

All as per item No. 47.00 here-in-before but Rotory type 200 Amp.

All as per item No. 47.00 here-in-before but Rotory type 63 Amp.

S&F for SWR rope of size 10 mm outer dia dor tie/anchoring with submersible pump complete set all as specified and directed.

M&L for painting of rising, delivery, overflow and backwash out pipes of 250 mm, 450mm,150mm capacity at Main filter pump house of various diameters with Blue, green, red and yellow colours respectively with synthetic enamel paint two coats including marking with arrows (directions of flow) and with white synthetic enamel paint over black (synthetic enamel paint) background of size (300 mmx300 mm) all as specified and directed.

Taking out old MCCB/ MCB any size and S&F 250 Amp MCCB, 4 pole including suitable size copper lugs &connected fittngs specified and directed.

All as per item No. 52.00 here-in-before but 200 Amp.

M&L cleaning of existing drainage system of filter pump house and cutting grass around 1 meter all including soil removing and connected work specified and directed.

Excavation in trenches not exc 1.5 mtr wide & not exc 1.5 mtr in depth for foundation etc or for manholes, laying of pipe lines,cables,pipes etc in Soft/loose soil and getting out complete all as specified and directed.

Returning filling in, including spreading, leveling watering & well rammng in layers not exc 25 cm thick complete all as specified and directed.

Removing excavated material to a distance not exc 50 mtr & depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified & diected.

M&L for brick with sub class B brick straight or curved on plain exc 6 mtr, mean radius built in cement mortar 1:4 complete all as specified and directed. (For repairing of old broken chamber )

M&L for PCC 1:2:4 type B1 using 20 mm stone graded aggregate as in copping/support both including necessary form work etc complete all as specified and directed.

M&L for rendering 15mm thick on fair face of brick work in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

S&F rotational moulded (three layered), ISI marked polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, hoisted and fixed in position including connecting up pipes including taking down old tank complete all as specified and directed.

M&L for reapir of air pressure machine any size and capacity complete all as specfied and directed. Model-ET5-7.5 Motor Cap-7.5 HP Rated Pressure-7.0 kg/cm2

S&F building security light 45 watt, IP-65 protection with clamp and bracket size 50 mm, medium grade, GI tubing complete with wiring all as specfied and directed.

M & L for earthing complete with galvanised steel plate earth electrode 600 mm X 600 mm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earthing strip of dimension 32X6 mm by means of bolts, nuts, check nuts and washers of galvanised iron from earth plate to test point upto 7.5 metre including all as shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete chamber in cement concrete M15 (Nominal Mix) using 20 mm nominal size coarse aggregate, precast RCC cover slab in cement concrete M15 (Nominal mix) using 20 mm nominal size coarse aggregate of size 40 cm X 40 cm X 5 cm reinforced with 8 mm dia TMT bars @ 150 mm c/c both ways with one handle for lifting made out of 8 mm dia bar, GI funnel, GI wire mesh filter, 20 mm dia GI pipe medium grade for watering, 20 mm dia GI pipe medium grade for protection of earthing lead, charcoal or coke and salt in alternate layers including testing complete all as specified and as directed. NOTE: Necessary excavation to be measured under corresponding item of schedule.

M&L for installing GI strip of 32x6 mm dimensions and making proper arrangements for connection between earthing and transformer/ equipment all as specified and directed.

S&F for repair of outdoor type LT pannel board mounted on angle / PCC floor of any size and replacement of unserviceable switch/control gears and connector, indicator lamps, panel door lock etc including rewiring and extension of incoming and out going cables by opening of loops/making joints with same size cable and provisioning of cable lugs /thimbles as required including replacement of rusted sheet metal door with existing size MS sheets by necessary arc/gas welding / making cover as per suitable and removing all dirt, dust etc with the help of air blower and painting complete Panel board with one coat of synthetic enamel spray painting over a coat of red oxide primer of Panel Board of approved colour including writing of identification etc all as specified and directed comprising the following :- (a) MCCB 100 Amp to 600 Amp, 3/4 pole 415 Volt -01 to 06 Nos (b) Indicator Lamp RYB, LED type with fuse.-01 set (c) Aluminium bus bar RYB & N of 200 A size -01 set (d) Amp / Volt Meter 02 Nos (e) MCB TPN/SPN/SP mounting on bus bar -01 to 6 Nos (f) door lock - 1 to 8 Nos Note : (i) Necessary eqpt and safety measures, stasonary reqd for load balancing arranged by the contractor without any extra cost. (ii) Cost of New aluminium/Copper thimbles, earth and neutral link, insulator, hylem sheet, any type of screws,door locks any type as per site reqmt change under the job deemed to be included in the quoted rate. (iii) MCCB, MCB, Aluminium bus bar, indicator lamp, required for relacement shall be measured and paid serately in relevent item.

M&L in replacement LED Type indicating Lamp for indication of RYB-01 Set

M&L in replacement aluminium bus bar rating 200 Amps, 25/6 mm including making whole suitable for panel with tape insulation of suitable colour in Phase RYB & neutral in Black colour complete all as specified and as directed by Engr-in-Charge,

M & L for preparation of old painted surface of F/P box / LT Panel & rewiring and extension of incoming and out going cables by opening of loops/making joints with same size cable and provisioning of cable lugs /thimbles as reqd including replacement of transparent PVC sheet with rubber gasket for window with existing size and removing all dirt, dust etc with the help of air blower and painting complete Panel board with one coat of synthetic enamel spray painting over a coat of red oxide primer of Panel Board of approved colour including writing of identification etc all as specified and directed by Engineer-in-Charge Note : (i) Necessary equipment and safety measures, stationary reqiured for load balancing arranged by the contractor without any extra cost. (ii) Cost of New aluminium/Copper thimbles, earth and neutral link, insulator, hylem sheet, any type of screws, door locks any type as per site requirment changes under the job deemed to be included in the quoted rate.

Supply and fixing in replacement of old unserviceable lugs after cutting the worn out /faulty cable end from LT pillar/panel box including necessary earth work for taking out the cable from loop line, returning, filling in and making cable lead by providing aluminium lugs including crimping with crimping tools in the existing LT cable 50 Sqmm to 250 mm including necessary connection complete all as specified and directed.

Supply and replacement in repair of aluminium strip 25 x 3.15 mm with saddles and fixing screws, insulators rawal plugs etc for conductor for roof and fixed on wall upto test point complete all as specified and directed.

Supply and fixing in replacement of wooden block heavy weight of size 15x15x15 cm with hole of 8 cm depth & suitable dia for fixing of air termination rod of any size incl dismantling and taking down old existing unserviceable wooden block complete all as specified and directed.

Supply and fixing in replacement of GI tubes, light grade, galvanised, 20mm bore including necessary GI fittings, laid in trenches or under floor or fixed with poles/walls for fixing of air termination including dismantling and taking down old existing unserviceable GI tubes light grade complete all as specified and directed.

Supply and fixing in replacement of single pointed air termination Aluminium rod 12mm dia, 300 mm long complete all as specified and directed.

Supply and fixing in replacement of test point terminal block made of gun metal or phosphorous bronge 75 x 75 x 25mm of 6mm thickness drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head brass screws including box of size 90 x 90 x 90mm made of 1.6mm plain sheet and screwed to wall for protection of test point complete all as specified and directed.

Supply and replacement in repair of new LED flood light fitting 100 watt JETA IRIS energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP-66, flood light, suitable for highlighting architectural facade and general purpose lighting etc complete fixed bracket made out by GI pipe, light grade, of suitable size and MS clamp and nut bolts washers etc complete and connected with twin core cable 1.5 sqmm from flood light to fittings connectorcomplete all as specified and directed.

S&F first Aid box wooden type with all ascessories complete all as specfied and directed.

Supply and lay cable XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of following sizes:-

10 Sqmm 2 core

16 Sqmm 4 core

50 Sqmm 3.5 core

120 sqmm 3.5 core

M&L local sand dry, filling in trenches around under ground cable complete all as specfied.

M&L for provinding of new type-I, flat LV, cable cover ,size 250mmx150mmx40mm for protection of under ground cable complete all as specfied and directed.

Supply only labour for reapir/maintaince section of swimming pool at 3 EME bairagarh all as directed and directed.

S&F decorative bollard solar garden light LED type wattage 10 watt For swimming Pool all as specfied and directed.

S&F 5mm rubber insulation sheet all as specfied and directed.

S&F Chemical dosing system pluger type suitable to inject solution upto 25 LPH comprising dosing pump coulped with three phase electric motor of cap 0.5 HP ,1440 RPM assembly with agitator in one motor, agitator with SS sweep blade duly FRP cated, FRP tank 150 lit cap complete unit mounted on heavy duty MS fabricated frame duly anticorrosive paint complete with chemical grade PVC NRV.

Deduct Schedule of credit (calculation will be done off line) Rs. 298961.00

City buildcom builders & devlopers

M/S SURINDER KUMAR MAHAJAN

ROYAL CONSTRUCTION

UMESH ENTERPRISES