PROVN OF DEFICIENT MD ACCN (GRIHA 3 STAR RATING) AT OLD AMRITSAR CANTT

Note:- Please refer Schedule 'A' Notes given on serial page No. 19 to 30 of tender documents.

LUMPSUM/ OTHER PRE-PRICED PROVISIONAL SCHEDULES OF WORKS

Lump sum price worked out by the contractor for BUILDING WORK as listed in Schedule 'A' Part-I brought forward from serial page No.31.

Lump sum price worked out by the contractor for EXCAVATION AND EARTH WORKS as listed in Schedule 'A' Part-II brought forward from serial page No.32 & 33.

Lump sum price worked out by the contractor for INTERNAL ELECTRIFICATION WORKS as listed in Schedule 'A' Part-III brought forward from serial page No. 34 to 38.

Lump sum price worked out by the contractor for INTERNAL WATER SUPPLY WORKS as listed in Schedule 'A' Part-IV brought forward from serial page No. 39.

Lump sum price worked out by the contractor for SEWAGE DISPOSAL WORKS as listed in Schedule 'A' Part-V brought forward from serial page No. 40 & 41.

Lump sum price worked out by the contractor for AREA DRAINAGE WORKS as listed in Schedule 'A' Part-VI brought forward from serial page No. 42.

Lump sum price worked out by the contractor for CHAIN LINK FENCING AND STEEL GATE WORKS listed in Schedule 'A' Part-VII brought forward from serial page No. 43 to 45.

Lump sum price worked out by the contractor for ROAD AND PATH WORKS as listed in Schedule 'A' Part-VIII brought forward from serial page No. 46 & 47.

Lump sum price worked out by the contractor for EXTERNAL WATER SUPPLY WORKS as listed in Schedule 'A' Part-IX brought forward from serial page No. 48.

Lump sum price worked out by the contractor for EXTERNAL ELECTRIFICATION WORKS as listed in Schedule 'A' Part-X brought forward from serial page No. 49 to 53.

Misc items of Works (To be quoted by Bidder) as listed in Schedule 'A' Part-XI

INTERNAL ELECTRIFICATION WORKS

Material & labour for point wiring with 1.5 sqmm, PVC insulated but unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit medium grade 20mm dia (minimum) or higher size as specified and cutting chasing on wall complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc/ fittings ISI marked for modular fittings and brass screws and cup washers including 1.5 sqmm stranded copper conductor PVC insulated FRLS cable green in colour as continuous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed. Note:- Cost of Metal boxes and modular accessories like cover plates will be paid seprately in respect items (a) Fan point/ exhaust fan point /one light point/bell/buzzer controlled by one switch/bell push.

(b) One socket outlet 5 pin 5 Amp controlled by one, one way switch on same board.

(c) One socket outet point 5 amps on the independent board.

(d) One light point controlled by two nos of two way switch.

All as Ser item 3.02 here in before but with 2.5 sq mm wire and earth wire of 2.5 sq mm for 3 Pin 15 Amp modular type socket outlet.

Supply and fix modular metal flush box made out of GI sheet, thickness not less than 1.2mm with earthing terminal, 8 module complete all as specified and directed.

Supply and fix modular metal flush box made out of GI sheet, thickness not less than 1.2mm with earthing terminal, 12 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 12 module complete all as specified and directed.

Supply and fix modular Dummy plate complete all as specified and directed.

Supply and fixing LED energy efficient LED bulb B22 9 watt complete all as specified and directed.

Supply Install testing and commissioning LT Distribution Panel (CPRI type tested) cubicle type IP-56 wall mounted, indoor type conforming to IS-61439, factory fabricated made out of 2mm thick CRCA sheet outer & 2mm thick CRCA sheet inner of suitable size to accommodate all accessories/ fittings compartmentalized in construction to accommodate the incoming MCCB and TPN bus bars and outgoing feeders. The TPN bus bars shall be insulated with colour coated heat shrinkable sleeve and shall be mounted on DMC supports. The incoming as well as outgoing MCCBs/MCBs shall have extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. The extension links shall be supported on DMC and having provision for termination of incoming and outgoing cables. All extension links/ interconnections shall colour coated sleeves. A detachable gland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be painted with powder coated finish with RAL 7032 SIEMENS GRAY Structure after seven tank phosphate treatment, front & back opening type, and fixing 2 Nos danger notice plate with letter, figures and conventional skull bones in signal red colour and fixed front & back door to LT Panel with voltage and danger indicated in Hindi and English with double door shutter and shall have louvers and air vent gasket for natural flow of air Neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of following: (a) Aluminium Bus bar for 3 phase 4 wire system of 4X 250 A rated insulated aluminium strip mounted on resin cast insulator in independent compartment having front openable shutter - One Set. (b) MCCB, four pole 415 Volt 160 Amps 25 KA with adjustable overload setting Ir. (b) MCB TPN 40 Amp, 10KA -06 Nos (c) MCB SP 20 A-04 Nos (d) Voltmeter 0-500V Digital inbuilt VSS-01 Nos (e) Amp meter 200A Digital inbuilt ASS (f) CT's 150/5A-01 Set (g) indicator lamp LED in Red/Yellow/Blue colour-01 set of three. (For Officer Md Accn)

Supply and fix Telephone socket RJ11-1 module with connector and complete all necessary fitting as directed.

M & L for wiring with one run single core FRLS Wire, 1100 volt grade, PVC insulated and unsheathed cable with stranded copper conductor 1.5 sqmm (for inverter) drawn into existing PVC conduit with all accessories fixed concealed complete all as specified and directed. NOTE: (a) One run 1.5 sqmm PVC FRLS multi stranded copper cable wire with separate colour coding for inverter should be used, no extra cost will be paid in this account.

Supply and fix LED tube light fitting for all purpose surface and wall mounted with single side connection polycarbonate LED batten with 125 Lum/watt system effiency polycarbonate housing and integrated electronic driver of capacity 20 W, four feet and connection with PVC insulalted twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed. Make: Havells cat part No. ENDURALINEARPROBS20WLED865SPCSSIND or equivalent make of Bajaj/Crompton/ Philips.

Supply and fix wall/ceiling mounting LED 9/10 Watt tube light fitting with polycarbonate housing and integrated electronic driver complete with all acessories 1x9 Watt LED, with CCT of 6000k suitable for domestic application, 240 Volts, 50 Hz, and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete all as specified and directed. Make: Havells cat part No. LUMILINEBS9WLED865SPCWH or equivelent make of Bajaj/ Crompton/ Philips.

Supply and fix decorative wall light fixture of polycarbonate type insulated body with back plate suitable for Led lamp B22 base including led lamp 9 watt complete all as specified and directed.

Supply and fix Bed side LED light fitting Aluminium base body 1x3 watt fixed on wall at suitable height all as specified and directed. Make:Phillips/Havells/Bajaj

Supply and fix bldg street fitting made up of pressure die cast aluminum housing with high efficiency LEDs as a lighting source and lens embedded PC Cover Having TOP oppening seperate driver compartment with IP 66 protection and impact resistance of IK07, CCT 5700 K, of wattage 25 Watt including connection with 3 core PVC insulated overall sheathed flexible cable with multi stranded copper conductor of size not less than 1.0 sq mm from celing rose to fitting terminal all as specified and as directed. Make :- Havells/ Bajaj/ HPL/Philips

Supply and Fixing GI pipe bracket made out of GI pipe light grade 32mm dia and bend to shape 1.5 mtr long MS clamps made out of MS flat iron (02Nos) of size 32x4mm thick compitable with bldg security light mentioned in item Ser No. 45 with nuts & bolts, washers fixed to wall/pole at specified height complete all as specified and directed.

Supply and fix Kitchen Wall Fan 300 mm sweep, 1350 RPM, of Elegantly designed fan base in round shape for 50 cub mtr/min air delivery and minimal noise levels with pull code control for speed & oscillation upto 90 degree total flexibility, double 'z' shielded ball bearing, sturdy brazed wire guards with power coating ensures corrosion resistance conforming to IS 2997-1964 complete all as specifed and directed.

Supply and fix Kitchen Chimney Dry Heat Auto Clean Technology Stainless with Air outlet 150 mm, Steel Finish Front Matte Black Glass panel with Digtal Display Touch Control Panel with 3 Speed Gesture motion, Heavy Duty Baffle Filters, minimium Air flow 1180 M3/h Energy Saving LED Light of suitable wattage, Copper winding BLDC Motor, 62dba max noise level and voltage 220-240 V/50 Hz including making hole in the wall and making good the distubed surface of wall including all accessories all as specified and directed. Make : KAFF Model No. SKU NEVISHC90 or eqvt in Hindware/ Faber.

INTERNAL WATER SUPPLY WORKS

Supply & fixing 15mm CP brass health faucet (hand shower), inlet length 100mm fixed to angle valve with and including decorative choice flexible pipe, wall hanger etc complete all as specified and directed.

Supply and fixing for 15mm bore fancy type central hole single lever basin mixer with 450 mm swivel spout Connecting Legs & wall Flanges & including all necessary fittings all as specified and directed. Make: F2013451 of Cera/QQP-CHR-7167BPM of Jaquar/ K-27484IN-4-CP of Kohler/ T5A8497CA1 of Roca

Supply and fixing for two way bib cock with single handle and wall flange 15mm dia, fancy type chromimum plated including all necessary fittings all as specified and directed. Make: F20131501 of Cera/ LYR-CHR-38041 of Jaquar or equivalent in Kohler/Roca

Supply and fixing for 15 mm bore Sink Mixer with Swinging Spout (Wall Mounted) with 150mm long braided connection pipes & including all necessary fittings all as specified and directed. Make: F2013501 of Cera/ ARI-CHR-39165 of Jaquar/ K-20591IN-4-CP of Kohler/ RT5A8497CA1 of Roca

Supply and fixing for 15mm dia Wall Mounted Bib Cock, Chromium plated, with wall flange and aerator including all necessary fittings all as specified and as director. Make: F1015151 of Cera/ 16094IN-4-CP of Jaquar/ K-16093IN-4-CP of Kohler/ RT5A937ACA1 of Roca

ROAD AND PATH WORKS

Material & Labour for preparing bituminous surfaces of road and marking 2.5mm thick centre lines. stop lines, dashes, arrows etc. and the like n. exc 125mm wide on roads pavements with hot applied thermo plastic road marking paint of pproved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed.

EXTERNAL WATER SUPPLY WORKS

Supply and fixing sluice valve of 150mm (6") dia flanged and drilled both ends Cast Iron body, heavy duty, class PN-1.0, stainless steel spindle conforming to IS:14846-2000, S/s gate, seating rings both end flanged & drilled and iron wheel head including jointing with and including rubber gaskets, bolts, nuts & washers complete all as specified and directed

All as per ser item No. 6.02 above but of size 100 mm (4”) dia

All as per ser item No. 6.02 above but of size 80 mm (3”) dia

Supply & laying Ductile Iron pipes pressure with spigot & socket ends of 150mm bore class K-9 centrifugally cast conforming to IS:8329/2000 blast furnace slag cement portland cement properties suitable for push-on jointing with inside surface cement mortar lining, with internal metallic zinc coating and external black bitumen coating, duly ISI marked complete laid in trenches or under the roads, with and including tyton rubber gasket push-on joints as required at site complete all as specified and as directed

All as per ser item No. 6.05 above but for DI pipe of 100mm dia NOTE FOR SER ITEM NO. 6.05 & 6.06 (a) The cost of DI fitting shall be measured and paid separately under relevant item. (b) Excavation & other earth work will be measured and paid separately under relevant items.

Material and labour for construction of brick masonary pits (230mm thick wall) of 900x600x1000mm internal dimension (bottom PCC floor of the pit should be minimum 30cms below the bottom surface of sluice valve flange to provide sufficient working space), bottom floor of the pit be constructed in PCC (1:4:8) type D2 using 15cms thick with 20mm stone aggregate for foundation, brick wall with sub class 'B' bricks built in CM 1:6, inner and exposed surfaces and bottom floor of the pit should be plastered in cement mortar (1:4) 15mm thick, PCC 1:2:4 type B1 using 20mm graded stone aggregate for coping. The sluice valve and other fittings should be housed in center of the pit. The vertices of the pit should in right angle and chamfered. The top cover of the pit will be made out of MS sheet 3mm thick with angle iron frame made out of MS angle 50mmx50mmx6mm with galvanized steel hinges two Nos. and locking arrangements duly painted with two coats of water resistant synthetic enameled paint over one coat of red oxide including necessary excavation and earth work in any type of soil complete all as specified and directed.

All as per ser item No. 6.07 above but of valve pit of internal dimension 450mm x 450mm x 600mm complete all as specified and directed.

EXTERNAL ELECTRIFICATION WORKS

Taking down existing XLPE Insulated under ground electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size (3½ x 70mm²/50mm²/25mm²) & type remove from site including necessary earth works complete all as directed

Taking down LT UG cable from transformer to maint existing main panel and relaying from prop maint LT panel to existing panel complete all directed by Engr-in-Charge

Supply Install, testing and commissioning LT Distribution Panel (CPRI type tested) cubicle type IP-56 wall mounted, outdoor type conforming to IS-61439, factory fabricated made out of 3.15 mm thick CRCA sheet outer & 2 mm thick CRCA sheet inner of suitable size to accommodate all accessories/ fittings compartmentalized in construction to accommodate the incoming/outgoing MCCB and TPN bus bars and outgoing feeders. The TPN bus bars shall be insulated with colour coated heat shrinkable sleeve and shall be mounted on DMC supports. The incoming as well as outgoing MCCBs shall have extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. The extension links shall be supported on DMC and having provision for termination of incoming and outgoing cables. All extension links/ interconnections shall colour coated sleeves. A detachable gland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be painted with powder coated finish with RAL 7032 SIEMENS GRAY Structure after seven tank phosphate treatment , front & back opening type, and fixing 2 Nos danger notice plate with letter , figures and conventional skull bones in signal red colour and fixed front & back door to LT Panel with voltage and danger indicated in Hindi and English with double door shutter and shall have louvers and air vent gasket for natural flow of air Neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of following:-(Main Panel near Sub Stn No. 4 and for offrs Block No. 2 & servant block No. 1 to 4 - Khetarpal Enclave) (i). Bus bar Aluminium 500 amps rating -04 Nos. (ii). MCCB as Incomer 4 pole 250 Amps 415V 35 kA Micro processor based -01 No. (iii) MCCB, 4 pole 160 Amps 415V, 25 kA Thermal magnetic -02 No.(Outgoing for Prop Offrs Md Accn (Block 3 & 4)) (iv) MCCB, 4 pole 100 Amps 415V, 16 kA Thermal magnetic-01 Nos. (Outgoing for Prop Offrs Md Accn Block-2)

Supply Install, testing and commissioning LT Distribution Panel (CPRI type tested) cubicle type IP-56 wall mounted, outdoor type conforming to IS-61439, factory fabricated made out of 3.15 mm thick CRCA sheet outer & 2 mm thick CRCA sheet inner of suitable size to accommodate all accessories/ fittings compartmentalized in construction to accommodate the incoming/outgoing MCCB and TPN bus bars and outgoing feeders. The TPN bus bars shall be insulated with colour coated heat shrinkable sleeve and shall be mounted on DMC supports. The incoming as well as outgoing MCCBs shall have extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. The extension links shall be supported on DMC and having provision for termination of incoming and outgoing cables. All extension links/ interconnections shall colour coated sleeves. A detachable gland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be painted with powder coated finish with RAL 7032 SIEMENS GRAY Structure after seven tank phosphate treatment , front & back opening type, and fixing 2 Nos danger notice plate with letter , figures and conventional skull bones in signal red colour and fixed front & back door to LT Panel with voltage and danger indicated in Hindi and English with double door shutter and shall have louvers and air vent gasket for natural flow of air Neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of following:- (Feeder Panel near Prop offrs block No. 3 & 4 and servant block 5 to 9 - Khetarpal Enclave) (i) Bus bar Aluminium 300 amps rating -04 Nos. (ii) MCCB as Incomer 4 pole 160 Amps 415V 25 kA Micro processor based -01 No. (iii) MCCB, 4 pole 100 Amps 415V, 16 kA Thermal magnetic -02 Nos. (Outgoing for Prop Offrs Md Accn Block 3 & 4) (iv). Provn for space spare MCCB 4P, 100A - 01 No. (v) MCB, SPN 6-32 Amps, 10 KA - 05 Nos. (outgoing for Servant Block No. 5 to 9) (vi)CTs ratio suitable size ISI marked - 1 Set (Three each)

Supply Install, testing and commissioning LT Distribution Panel (CPRI type tested) cubicle type IP-56 wall mounted, outdoor type conforming to IS-61439, factory fabricated made out of 3.15 mm thick CRCA sheet outer & 2 mm thick CRCA sheet inner of suitable size to accommodate all accessories/ fittings compartmentalized in construction to accommodate the incoming/outgoing MCCB and TPN bus bars and outgoing feeders. The TPN bus bars shall be insulated with colour coated heat shrinkable sleeve and shall be mounted on DMC supports. The incoming as well as outgoing MCCBs shall have extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. The extension links shall be supported on DMC and having provision for termination of incoming and outgoing cables. All extension links/ interconnections shall colour coated sleeves. A detachable gland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be painted with powder coated finish with RAL 7032 SIEMENS GRAY Structure after seven tank phosphate treatment , front & back opening type, and fixing 2 Nos danger notice plate with letter , figures and conventional skull bones in signal red colour and fixed front & back door to LT Panel with voltage and danger indicated in Hindi and English with double door shutter and shall have louvers and air vent gasket for natural flow of air Neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of followins:- (Feeder Panel near Prop Offrs Md Accn Block-1 and servant block 1 to 3 at Manekshaw Enclave area) (i). Bus bar Aluminium 200 amps rating -04 nos. (ii) MCCB as Incomer 4 pole 125 Amps 415V 25 kA Micro processor based -01 No. (iii) MCCB, 4 pole 100 Amps 415V, 16 kA Thermal magnetic -01 No. (Outgoing for Prop Offrs Md Accn Block 1) (iv) Provn for space spare MCCB 4P, 100A - 01 No. (v)MCB, SPN 6-32 Amps, 10 KA - 03 Nos. (outgoing for Servant Block No. 1 to 3)

Supply Install, testing and commissioning LT Distribution Panel (CPRI type tested) cubicle type IP-56 wall mounted, outdoor type conforming to IS-61439, factory fabricated made out of 3.15 mm thick CRCA sheet outer & 2 mm thick CRCA sheet inner of suitable size to accommodate all accessories/ fittings compartmentalized in construction to accommodate the incoming/outgoing MCCB and TPN bus bars and outgoing feeders. The TPN bus bars shall be insulated with colour coated heat shrinkable sleeve and shall be mounted on DMC supports. The incoming as well as outgoing MCCBs shall have extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. The extension links shall be supported on DMC and having provision for termination of incoming and outgoing cables. All extension links/ interconnections shall colour coated sleeves. A detachable gland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be painted with powder coated finish with RAL 7032 SIEMENS GRAY Structure after seven tank phosphate treatment , front & back opening type, and fixing 2 Nos danger notice plate with letter , figures and conventional skull bones in signal red colour and fixed front & back door to LT Panel with voltage and danger indicated in Hindi and English with double door shutter and shall have louvers and air vent gasket for natural flow of air Neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of followin:- (Main Panel near Arty Bde Offrs Mess Sub Stn) (i) Bus bar Aluminium 1200 Amps rating -04 nos. (ii) ACB, 4 pole 800 Amps 415V, 50 kA Micro processor based - 01 No. (Incoming) (iii) MCCB, 4 pole 500 Amps 415V, 50 kA Micro processor based with fixed magnetic and thermal adjustable - 01 No. (for extg panel) (iv) MCCB, 4 pole 100 Amps 415V, 16 kA Thermal magnetic - 01 No.(for Prop JCOs Md Accn at Albert Ekka Enclave) (v) CTs ratio suitable size ISI marked - 1 Set (Three each)

Supply Install, testing and commissioning LT Distribution Panel (CPRI type tested) cubicle type IP-56 wall mounted, outdoor type conforming to IS-61439, factory fabricated made out of 3.15 mm thick CRCA sheet outer & 2 mm thick CRCA sheet inner of suitable size to accommodate all accessories/ fittings compartmentalized in construction to accommodate the incoming/outgoing MCCB and TPN bus bars and outgoing feeders. The TPN bus bars shall be insulated with colour coated heat shrinkable sleeve and shall be mounted on DMC supports. The incoming as well as outgoing MCCBs shall have extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. The extension links shall be supported on DMC and having provision for termination of incoming and outgoing cables. All extension links/ interconnections shall colour coated sleeves. A detachable gland plate of thickness not less than 3 mm thick should be used at the bottom for entry of armoured cable of adequate size compression glands, the panel shall be painted with powder coated finish with RAL 7032 SIEMENS GRAY Structure after seven tank phosphate treatment , front & back opening type, and fixing 2 Nos danger notice plate with letter , figures and conventional skull bones in signal red colour and fixed front & back door to LT Panel with voltage and danger indicated in Hindi and English with double door shutter and shall have louvers and air vent gasket for natural flow of air Neoprene adhesive type gasket shall be used to make panel vermin proof and comprising of followin:- (Feeder panel Near Prop JCOs Md Accn area at Albert Ekka Enclave incl Garrages and street lights) A. Bus bar Aluminium 200 amps rating -04 nos. B. MCCB, 4 pole 100 Amps 415V, 16 kA Micro processor based - 01 No. (Incoming) C. MCCB, 4 pole 40 Amps 415V, 16 kA Thermal magnetic - 03 Nos. (for Prop JCOs Md Accn blocks) D. Provn for space spare MCCB 4P, 100A - 01 No. E. MCB, SPN 6-32 Amps, 10 KA - 02 Nos. (for Garrages of Block-1 & 2)

Supply, fixing, testing & commissioning of junction box with MCB SP 6A, 10 kA, C curve & PVC cable 1.5 sqmm copper wire upto 7.5 mtr length for connection of security light fitting from junction box, enclosed in thermo plastic enclosure, shock proof, weather, dust, rust & water proof, internally embedded gasket with provision for cable entry trough gland of size 300x200x125mm alongwith MS clamps all as specified & directed

ARBORICULTURE

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, seprate the roots/grass and good earth by sieving with suitable seive size, stacking of good earth & mixed with suitable manure of ratio 5:1 including supply of manure, screened through sieve of 1.5 designation 4.75 mm and spreading the mixture of good earth & manure, applying suitable pesticides, watering to a depth of 15cms, including removal of roots/grass out of site Material and laying of 'DOOB GRASS'/Carpet Grass planting complete as aprroved and directed by the Garrison Engineer.

Excavation in post hole of size not less than 60 cm x 60 cm x 60 cm deep or according to the plant size & getting out the existing earth and planting the trees straight inside the pit and filling up the pit with and including the approved earth along with and manure (composit) in the proportion (3:1) and including Supply and Planting "Golden Dorenta Hedge" with proportionate girth, remove and spread the surplus excavated soil complete all as specified and as directed by the Engineer in Charge.

Excavation in post hole of size not less than 60 cm x 60 cm x 60 cm deep or according to the plant size & getting out the existing earth and planting the trees straight inside the pit and filling up the pit with and including the approved earth along with and manure (composit) in the proportion (3:1) and including Supply and Planting "Neem plant" with proportionate girth, remove and spread the surplus excavated soil complete all as specified and as directed by the Engineer in Charge.

Excavation in post hole of size not less than 60 cm x 60 cm x 60 cm deep or according to the plant size & getting out the existing earth and planting the trees straight inside the pit and filling up the pit with and including the approved earth along with and manure (composit) in the proportion (3:1) and including Supply and Planting "Ambla Tree" with proportionate girth, remove and spread the surplus excavated soil complete all as specified and as directed by the Engineer in Charge.

Excavation in post hole of size not less than 60 cm x 60 cm x 60 cm deep or according to the plant size & getting out the existing earth and planting the trees straight inside the pit and filling up the pit with and including the approved earth along with and manure (composit) in the proportion (3:1) and including Supply and Planting "Ashoka Tree/Mango" with proportionate girth, remove and spread the surplus excavated soil complete all as specified and as directed by the Engineer in Charge.

Excavation in post hole of size not less than 60 cm x 60 cm x 60 cm deep or according to the plant size & getting out the existing earth and planting the trees straight inside the pit and filling up the pit with and including the approved red earth along with and manure (composit) in the proportion (3:1) and including Supply and Planting "Ficus/Kingbush" with proportionate girth, remove and spread the surplus excavated soil complete all as specified and as directed by the Engineer in Charge.

Excavation in post hole of size not less than 60 cm x 60 cm x 60 cm deep or according to the plant size & getting out the existing earth and planting the trees straight inside the pit and filling up the pit with and including the approved red earth along with and manure (composit) in the proportion (3:1) and including Supply and Planting "PLUMERIA" with proportionate girth, remove and spread the surplus excavated soil complete all as specified and as directed by the Engineer in Charge.

Excavation in post hole of size not less than 60 cm x 60 cm x 60 cm deep or according to the plant size & getting out the existing earth and planting the trees straight inside the pit and filling up the pit with and including the approved red earth along with and manure (composit) in the proportion (3:1) and including Supply and Planting "Gulmohar Tree" with proportionate girth, remove and spread the surplus excavated soil complete all as specified and as directed by the Engineer in Charge.

Excavation in post hole of size not less than 60 cm x 60 cm x 60 cm deep or according to the plant size & getting out the existing earth and planting the trees straight inside the pit and filling up the pit with and including the approved red earth along with and manure (composit) in the proportion (3:1) and including Supply and Planting "Amalthas" with proportionate girth, remove and spread the surplus excavated soil complete all as specified and as directed

Provision of tree guard around trees height 1.5m and size 60 x 60 cm with angle iron 40 x 40 x 5 mm and 40 x 3 mm MS flat to support angle, 3mm hard wire mesh(50x50mm opening) complete all as specified by Engr-in-charge.

Sprinkler system components for 50 mm dia pipe complete all as specified and as directed (a) Supply & fixing HDPE pipes with quick action counter (2.5 kg/cm2) of 6 mt long (25 Nos) (b) Supply & fixing sprinkler coupler with fool baten assembly (08 Nos) (c) Supply & fixing sprinkler nozzles (1.7 to 28 in/cm2) (05 Nos). (d) Supply & foxing riser pipe 20 mrn diameter x 75 cm long (05 Nos) (e) Supply & fixing connecting nipple (01 No) (1) Supply & foxing band with coupler 90 deg (01 No) (g) Supply & fixing Tee with coupler (01 No) (h) Supply & fixing End plug (02 Nos)

Supply & fix of Drip kit (16 mm dia) complete all as specified and as directed

Supply & fixing of Drip tape-250 PP45 cm 9 inch/16 mm /50 meter complete all as specified and as directed

Supply & Fixing of CI Water meter throated type of size 40mm dia class-A conforming to IS-779/94 complete all as specified and directed.

Supply & Fixing of Cl Water meter threated type of size 80mm dia class-A conforming to IS-779/94 complete all as specified and directed.

ROOFTOP SOLAR POWER PLANT SYSTEM

Design, supply, erection, installation, testing and commissioning of ON GRID type Roof Top Solar Photo Voltaic Power Plant system of 11.0 KW capacity complete incl comprising of DCR Solar Photo Voltaic Modules (cap as specified under in reqd qty to make full cap 11.0 KWp), Inverters/PCUs, Module mounting structure, Net meter (as applicable) , Generation meter, Array Junction boxes, DC junction/ distribution boxes, AC junction/ distribution boxes, Solar grade DC copper cables, AC cables, Lightning arrestor, surge arrestor, Earthings, civil RCC/ PCC/ earth work, Ladders, below mentioned items, BOS, accessories complete incl miscellaneous items reqd for satisfactory functioning of roof top solar power plant suitable to be installed. (For Offr Md Accn Manekshaw Enclave-01 No, Offr Md Accn Khetrapal Enclave-03 Nos).

Design, supply, erection, installation, testing and commissioning of ON GRID type Roof Top Solar Photo Voltaic Power Plant system of 4.0 KW capacity complete incl comprising of DCR Solar Photo Voltaic Modules (cap as specified under in reqd qty to make full cap 4.0 KWp), Inverters/PCUs, Module mounting structure, Net meter (as applicable) , Generation meter, Array Junction boxes, DC junction/ distribution boxes, AC junction/ distribution boxes, Solar grade DC copper cables, AC cables, Lightning arrestor, surge arrestor, Earthings, civil RCC/ PCC/ earth work, Ladders, below mentioned items, BOS, accessories complete incl miscellaneous items reqd for satisfactory functioning of roof top solar power plant suitable to be installed. (For JCOs Md Accn 908 Fd Regt-03 Nos, JCOs Md Accn Somaji Enclave-04 Nos)

Sl Item 9.01 & 9.02 Contd…. (e) Each module shall have RFID tag encapsulated/ laminated inside glass. Following information must be mentioned in RFID. (i) Name of Manufacturer of SPV Module. (ii) Name of Manufacturer of Solar Cell. (iii) Month and year of Manufacturing (seperately for solar cell and module). (iv) Country of Origin for solar cell and module. (v) Peak wattage, Im, Vm and fill factor of the module. (vi) Date of year of obtaining IEC PV module qualification certificate including the test lab issuing IEC certificate. (vii) Unique serial no and model no of module. (viii) IV curve of module (f) The temperature coefficient (Power) for the PV module shall not be more than - 0.40% per degree Celcius. (g) Every module must have bypass diode of suitable capacity. (h) PV module must confirm to latest edition of IEC 61215/ IS 14286, IEC 61853 Part I or IS 16170 Part-I. In addition the modules must confirm to IEC 61730 Part-1 & Part-2 and IS-17210 (Part-I) or IEC 62804-1 (PID). For use in a highly corrosive atmosphere throughout their life time, modules must qualify to IEC 61701/IS 61701. (j) It shall also be in confirmity to latest minimum technical specifications issued by MNRE & IREDA from time to time. DCR Modules should be of MNRE's ALMM & IREDA approved companies & as per latest IEC/IS standards.

Sl Item 9.01 & 9.02 Contd…. (k) Plants installed in high dust geographies like Punjab must have the solar modules tested with relevant dust standards (Applicable standard would be IEC 60068-2-68). (l) Both PV cells and SPV modules shall be make in India. (m) Each structure should have angle of inclination as per the site conditions to generate maximum power. (n) Any damage to the existing roof treatment of any type due to the Installation of Solar Power System shall be Re-done/made good as per existing treatment. Cost of the same shall be deemed to be included in the unit rate quoted. Nothing extra shall be admissible on this account.

Sl Item 9.01 & 9.02 Contd…. (B) DC distribution/ Junction Boxes : S&F DC junction boxes of suitable capacity, rating & Nos (as per design approved)/ OEM recommendations having suitably rated inputs and output terminals having separate DC fuses for both (+) & (-) on input and isolator on output terminal for each string. Each junction box must have a spare input terminal. The junction boxes shall be dust and vermin proof and water proof made of FRP/ Thermo Plastic with IP 65 protection or better standard in compliance with IEC 62208 and shall be UV resistant, fire retardant. It shall have surge protection and suitable arrangement for earthing connections as per relevant standard. The junction box shall have suitable arrangement of the following :- (a) The strings are required to be connected to the copper bus bar/ switch gear through individual fuses. (b) Provide arrangement for disconnection (DC dis-connection switch) for each string/SJB/ SCB. (c) Provide a test point for each sub group for quick fault location and to provide group array isolation. (d) Each array box shall be of relevant IEC standard/ IS standard. (e) The incomming and outgoing cables from box, panel shall be properly sealed through proper glands. (e) Each array junction box shall have suitable bypass & reverse blocking diodes for maximum DC blocking voltage of 1000V or system voltage as approved designed with suitable arrangement of its connection. Reverse blocking and bypass diodes shall work for extreme temperatures and shall have efficiency of 99.98% confirmed by appropriate IEC standard. Make : As per OEM

Sl Item 9.01 & 9.02 Contd…. (D) Module Mounting Structure (MMS): Design, supply/ procure, fixing, module mounting & support structure made of hot dipped galvanised iron with min 80 micron thickness including necessary RCC foundation (as applicable) and associated iron work cutting, drilling, welding, jointing, grouting, PCC/ RCC filling, dispoing waste material, etc., complete and fixing mounting arrangement suitable for SPV modules so as it can withstand wind speed of 200 km per hour. The mounting structure is to be installed at RCC Roofs (as existing at site) and the array structure has to be so designed that maximum load is directly on roof beams and columns to avoid any affect on life & strength of structure. It shall also occupy minimum space without sacrificing the output of SPV panels & adequate space between the arrays shall be available for easy cleaning and maintenance. Nuts, bolts, mounting structure including module mounting structure shall have to be adequately protected from the atmosphere and weather prevailing in the area. All the fasteners, nut, bolts shall be of Stainless Steel of grade SS 304 or hot dip galvanized. Module mounting structure may require to customize with respect to the site availability and in case, if any water tank is present on the roof, then mounting structure height should be more than 1.5 feet (min) above the water tank height so that space of water tank should be fully utilized for installation of PV module and to avoid any shadow of water tanks on modules. Notes for MMS: (a) Two numbers of anti theft fastners of Stainless Steel on two diagonally opposite corners of each module shall be provided. (b) The module mounting structure shall be installed to provide maximum generation.

(F) Power Conditioning Unit / Grid Tied Inverter : Design, supply, installation, testing and commissioning 3 phase PCU/ string inverters - 01 Nos(min) or higher qty as per site/ design approved of suitable capacity as given AC (nominal power), suitable to convert DC power of installed Solar PV module/ array to AC for planned building for further feeding to grid confirming to IEC:61683/ IS 61683, IS 16221 (Part 2), IS 16169 and IEC 60068-2 (1,2,14 & 30)/IEC : 62093 (as applicable)/ equivalent BIS standard for efficiency, for safety and for reliability. The input DC & output AC technical specification of Inverter are as under :-. Input (DC) (a) Max input Voltage : 1100 V (b) Rated Input Voltage : 600 V c) Start-up input voltage : 200 V d) Operating input DC voltage range : 300 - 950 V (e) No of independent MPPT : Must be suitable to accommodate installed DC SPV array & their cap. Min 2 to 10 (as per approved design based on No of array strings) (f) MPPT operating voltage range : 180 - 960 V (g) Max input DC Current : As per approved array string design (h) Maximum input short circuit current : As technically reqd & Suitable as per approved array string design (j) No of Protected DC inputs/ strings : 6 to 20 (as per approved design based on No of array strings)

Sl Item 9.01 & 9.02 Contd…. Output AC (a) AC grid connection type : 3/N/PE (b) Rated Power at unity PF: Suitable for SPV DC cap installed at building. (c) Max AC output power : 110% of rated power (d) Max AC output Apparent power : As per Inverter rated output (e) Max AC output Current : As per Inverter rated output (f) Max AC fault current : As per Inverter rated output (g) Nominal Output Voltage : 415 V (h) Grid Output voltage range : According to SEB standard (j) Rated Grid Frequency : 50 Hz (k) Output Frequency : 50 Hz ± 3Hz (l) Power factor : > 0.9 (Lag or lead) (m) Thermal Harmonic Distortion i (THDi) : < 3% (n) MPPT Efficiency : > 99% (o) EU efficiency : 97.5% (p) No of Protected DC inputs :

GENERAL DETAILS (a) Standby operation consumption (at night) : < 2 W (b) No load losses: Less than 1% of rated power (c) Allowable Relative Humidity rage : 0 ~ 100 % (d) Ambient temperature range : - 25 degree centigrade to 60 degree centigrade (e) Active power Adjustable range : 0 ~ 100 % (f) Topology : Transformerless (g) Integrated DC switch : Yes (h) Protection : The inverter should have provisions of Galvanic isolation, anti-islanding protection (IEEE 1547/UL 1741) equivant IS, DC Reverse Polarity protection, Output overcurrent & output over voltage protection, ground fault monitoring, grid monitoring, AC and DC short circuit current and over current, AC and DC over voltage and over temperature protection., AC & DC Surge protection, prevent lightning damage etc (j) Ingress Protection : IP 65 or better (k) Remote Monitoring : Wifi/ GPRS/ RS 485 as necessitated by site conditions & directed by GE. Web based monitoring with historical data storage for analysis (l) Display: LCD (m) Warranty : 5 years Min

(n) The inverter shall adjust voltage and frequency levels to suit the grid. (o) The inverter shall be self commulated with Pulse Width Modulation (PWM) technology and shall be capable of synchronise maximum within one minute or less time. (p) Maximum Power Point Tracker (MPPT) shall be integrated in the inverter/ PCU to maximize energy drawn from the array. Charge controller (if any)/ MPPT units environmental testing should qualify IEC 60068-2 (1,2,14,30)/ Equivalent BIS standard. (q) Monolithic design of inverter is not permitted. (r) The inverter shall have suitable nos of protected inputs (as per design) and outgoing shall be protected by ACB/MCCB. (s) All inverters/PCUs shall be IEC 61000 compliant for electromagnetic compatibility, harmonics, Surge, etc. (t) The inverter should have MODBUS, PROFIBUS, ETHERNET common ports.

Sl Item 9.01 & 9.02 Contd…. (b) NET METER(as applicable): CT/VT operated bidirectional energy meter (as reqd) with following features :- (i) True four quadrant metering (ii) Import/ export metering and forwarded metering option for LT systems (iii) Time and day metering with maximum demand registration and automatic billing (iv) LCD display with announciators for various critical events (v) Scroll lock feature for continuous display of a desired parameter on display (vi) High resolution energy display mode for dial test (vii) DLMS protocol for meter reading, with option to remote reading port. (viii) Advanced event detection features for voltage, current and magnetic influence (ix) Meter reading in absence of mains, using internal battery.

General Notes for SPV Plant System : (a) The contractor must visit the site before quoting the rates to assess the site conditions so as to decide up on location and layout of SPV, placement of inverter as per buildings, length of DC cables, AC cables, lightning arresters, earthing, mounting structure etc,complete. (b) The contractor shall submit complete scheme including electrical diagram of the work, schematic diagram, SPV module layout, location/ placement of LAs, Civil work, etc., complete as per MNRE/ IREDA latest guidelines as applicable, relevant IEC/IS norms to the GE for approval within one month of date of commencement of the work for approval. Design calculation: The tenderer should work out design based on the conditions prevalent at Amritsar , Punjab. The complete design and installation and layout of solar roof system be carried out in consonance with MNRE latest guidelines for roof top solar phase and preliminary solar panel direction layout, structure design with Stad pro/ equivalent software and single line diagram be ratified by MNRE empanelled charted Engr/ firm/ consultant. The dimensioned drawing of the site of work clearly marked with all sub systems components etc shall be submitted to GE for approval. which shall be self contained and self explanatory representation of layout of equipment and subsystems. Schematic diagram of the electrical system. This shall contain specification, size, current, voltage and fault levels rating of all cables,switch gears and instrumentation & control systems and all metering and interlocking etc. All the documents/technical details mentioned above duly vetted as specified above shall be approved by GE. GE may approve the documents as submitted by the Contractor or may suggest modification/alteration in documents/technical specifications duly supported with reasons for the same. The work shall be executed based on the approved documents.

AIR QUALITY DISPLAY SYSTEM

Supply and fixing of indoor air quality monitor display 3.5" TFT for parameters PM 2.5, PM10, Carbon Dioxide, Temp Humidity, Total volatile compounds with + WiFi support including charger of input AC 110-240 V, 0.3 A/ 50-60 Hz/2Amp, Charger output of 5V-2A (max) connected to the device via micro USB socket, power consumption of 10 watt, internal battery 2°2900 mAH/3.7. V Lithium ion rechargeable battery, battery backup 6 to 8 hours Back dimensions (width-120 mm, height- 120 mm, protrusion 2mm, total height 122 mm) Front dimension (width-117 mm, height-117 mm, protrusion - 2 mm, total height-119 mm), weight 370 gm, material made ABS, IP Rating IP 51, operating temp 0 to 60 deg C and operating humidity 0 to 95%. complete all as specifeid and directed.

Please Enable Macros to View BoQ information