CERTAIN BR MAINT WORK LIKE PLUMBING, FLOORING, ROOF ETC AT CELL NO 1 UNDER GE (NW) NOFRA, COLABA MUMBAI

Dismantling of plain or corrugated steel sheeting ,of any gauge ,thickness , including Nainital or similar pattern roof coverings all as specified

Dismantling wall and ceiling boards ( fibre , pulp,insulation etc.) or insulation boards / slabs / blankets , any thickness , including fillets all as specified

Dismantling wrought iron or mild steel work of any description not other wise provided for complete all as specified

Dismantling structural steel work including doors , gates but excluding framed truss etc. complete all as specified

Demolition of Cement concrete ( unreinforced ) in ground floors and pavings n.exc. 15 cm thickness ( below and above ground level ) complete all as specified

Demolition of Reinforcement Cement concrete of any description and in any position not otherwise specifically provided for complete all as specified

Demolition of brick work built in cement mortar including all quoins , arches, pillars , etc. complete all as specified

Taking down cement plaster or cement lime plaster of any description on brick or stone walls etc incl raking out joints hacking for key scrubbing down with water etc complete all as specified

Rendering 15 mm thick cement plaster in cement mortar 1:6 on fair faces of brick work or concrete surfaces complete all as specified and directed.

Rendering 15 mm thick cement plaster in cement mortar 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed including water proofing compund (Note: Water proofing compund shall be measured and paid separately under relevant item)

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer all as specified

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer all as specified

Preparation of old plastered surfaces of walls and applying one coat of cement base paint on walls complete all as specified

Preparation of old plastered surfaces of walls and applying one coat of exterior emulsion paint complete all as specified

S&F curvature type pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/clading to wall, fixed with self tapping screws as per existing shed profile complete all as specified.

S&F 2mm thick fiblre glass reinorced translucent corrugated sheeting iwith two corrugations side lap, matching with galvatum corrugated sheet fixed with coach screw and washers in roof, wall etc complete all specified and as directed.

M &L 40 mm thick Cement concrete Type B1 , 1:2:4 using (20 mm graded stone aggregate) in flooring finishing cement concrete suurface even and smooth using extra cement complete all as specified

M &L 100 mm Cement concrete type B-2 , 1:2:4 ( 40 mm graded stone aggregate ) finishing cement concrete surfaces even and smooth without using extra cement complete all as specified

M &L 75 mm Cement concrete type -2 , 1:3:6 ( 40 mm graded stone aggregate ) finishing cement concrete surfaces even and smooth without using extra cement complete all as specified

M&L Cement concrete1:4:8 type D2 using (40 mm graded stone aggregate) in foundation , filling and mass concrete etc.complete all as specified

M &L cement concrete1:2:4 type B0 using 12.5 mm graded agg in roof kerbs or mud stops , rounded , or chamfered on edegesor in roof padding complete all as specified

M&L Cement concrete1:2:4 type B1 using (20 mm graded stone aggregate) in lintels upto 1.5m clear span ,cills, steps, seismic and oter similar bands ,plinth courses, string courses, lacing courses,parapets,and railing upto 60cmin height,copings ,kneelers,apex stones,bed plates, bed blocks,water trough and the like including weathering ,slightly rounded or chamfered angles and throating .complete all as specified [Note: form work rate is included in the item]

M &L reinforced Cement concrete1:2:4 type B0 using 12.5 mm graded aggregate in beams, cantilevers , bressumers , lintels over 1.5 m span complete all as specified

Supply only liquid waterproofing compound

M & L Brick work with sub class " B "bricks, straight or curved on plan exc. 6 m mean radius built in cement mortar 1:4 complete as specified

Ditto as above item but except brick complete all as specified

Cutting out bricks , forming toothing for, and bonding new into old work including value of new materials entering old walls and jointing and pointing in cement mortar 1:3 (measured on vertical face in contact with old wall only )

S &F wire netting of galvanised steel wire 0.71 mm dia fixed with tinned tacks of wire staples size of mesh 25 mm complete all specified

M &L TMT bars 10 mm dia and over , cut to length , bent to shape required ,including cranking , bending ,spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips

Ditto , but 5 mm dia and over upto and including 10 mm dia in stirrups , spacers and binders all as specified

S&F for MS rolled section as in running rails and guides for sliding doors , grills etc. fixed with angle cleats, or other connecting plates Gde Fe-410-W (Gde-E-250) quality 'A' complete all as directed by Engineer-in-Charge.

S&F MS framed work as in door and gates of angle or other section with gusset plates, rails , braces etc indluding drilling, welding complete all as directed by Engineer-in-Charge.

Taking down 15 mm bore mild steel tubing of medium grade and connections incl cleaning for refixing or removal from site complete all as specified and as directed by Engineer-in-Charge

All as per above item No 09 here-in-before but for 20 mm bore

Refixing 15 mm bore old steel tubing and connections in new or old position ( walls ,ceiling, floors etc.)

Refixing 20 mm bore old steel tubing and connections in new or old position ( walls ,ceiling, floors etc.)

S&F 15 mm bore mild steel water tubing medium grade galvanized with all fittings and fixture fixed to walls ceiling or laid in floors complete all as specified and as directed by Engineer-in-Charge

All as per above item No 11 here-in-before but for 20 mm bore

S&F as in repair plastic water closet seat cover, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by Engineer-in-Charge

S&F in repair 32 mm bore chromium plated bottle trap for wash hand basin with inlet & outlet screwed for iron pipes or connection including necessary packing , union and cap as in repair complete all as specified and as directed by Engineer-in-Charge

S&F in repair PVC flushing cistern low level of 10 Ltr capacity valveless, symphonic action type (white colour) with inlet, balll valve, float end handle including flush pipe of 32 mm bore MS chromium plated and connection to pipe etc complete all as specified and directed by Engineer-in-Charge Make- Hindware/Paryware/Cera

S&F in repair 610 mm long PVC waste pipe flexible type 25 mm dia suitable for couplings 32 mm & 40 mm dia complete all as specified and directed by Engineer-in-Charge Make- Symet/ Prayag

S&F in repair waste fitting brass chromium plated of 32 mm dia for wash hand basin with long screwd sanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge Make : GEM/Parko/Soma

All as per above item No 18 here-in-before but 40 mm dia for sinks

S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 15 mm bore and fixed as in repair complete all as specified and directed by Engineer-in-Charge : Make-SANT/KARTAR/Leader

All as per above item No 22 here-in-before but but 20 mm bore

S&F as in repair 15 mm bore pillar taps cast copper alloy capaston head chromium plated, fancy type screwed down high pressure with or without lettered “ HOT” or “ COLD” with long screwed shanks and fly nuts screwed for iron pipes fixed as in repair complete all as specified and directed by Engineer-in-Charge ,

S & F in repairs Bib taps 15mm bore , chromium plated cast copper alloy with crutch or butterfly handle , screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed

S & F in repairs Bib taps 15mm bore , chromium plated fancy type cast copper alloy with crutch or butterfly handle , screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed

S & F in repairs Stop valves 15 mm bore , fancy type , chromium plated , cast copper alloy , screwed down , high pressure , with crutch or butterfly handle , screwed both ends for iron pipe or for unions complete all as specified and directed by Engr In Charge

S & F in repairs Ball brass valves 15 mm bore , high pressure , with polythene float and flynut complete , screwed for iron pipe or brass ferrule complete all as specified and directed

S & F in repairs Ball brass valves 20 mm bore , high pressure , with polythene float and flynut complete , screwed for iron pipe or brass ferrule complete all as specified and directed

S & F in repairs 15 mm bore Bib tap 15 mm standard of PTMT any colour high pressure screwed for iron pipe and fixed . ( Minimum wt - 90 gms ) all as specified

S&F in repair health faucet with double lock 1 meter brass plated stainless stell flexible hose and wall hook complete all as specified and directed

Disconnecting existing tanks of capacity exc. 250 litres & n. exc. 500 litres , setting aside ( or lowering if required ) for repairs , cleaning , etc. and hoisting if required reconnecting and refixing in position complete all as specified

Disconnecting existing tanks of capacity exc. 500 litres and not exc. 1000litres , setting aside ( or lowering if required ) for repairs , cleaning , etc. and hoisting if required reconnecting and refixing in position complete all as specified

S &F Rotational moulded polyethylene water storage tanks 500 litres capacity ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR Part I and as directed by Engr In Charge

S &F Rotational moulded polyethylene water storage tanks 1000 litres capacity ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR Part I and as directed by Engr In Charge

S&F in repair grating doom 100mm dia of PTMT having minimum weight of 25gms

S&F in repairs toilet paper holder of stainless stell fixed to wall with CP brass screws complete..

S&F in repairs water closet anglo indian complete with flushing cistern, seat cover and internal accessories (including ‘P’/'S' trap) white colour of make Coral of Hindware or Equivalent and fixed as per manufacturers’ instructions and complete all as specified and as directed by the Engineer in Charge

S&F in repair 18/19 mm thick block board of commercial quality Gde-1 fixed with screws as in cup board shutters & shelves and pelmet boxes etc complete all as specified and directed by Engineer-in-Charge Make- Duro/National/Bhutan

M &L 0.90 mm thick Decorated laminate type 1 of surface finish , colour and pattern as approved , fixed with approved adhesive as per manufacturesr's instruction all specified

S&F in repair Brass chromium plated tubular towel rail 20 mm dia ‘D’ type 60 Cm long between flanges to wall with chromium plated brass screw, washers and nylon sleeves complete all as specified and directed by Engineer-in-Charge

Hacking out old broken glass (any thickness, size, quality or description) from fixed with beads aluminium frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones

S&F 4mm Sheet glass,ordinary quality and glazing clip, rupper biding or putty in square n exc 0.5 sq. m in each pane

Taking down aluminium door shutter with Al chowkhat complete all specified

Supplying and fixing 5.5 mm thick sheet glass ordinary quality n. exc. 0.50 Sq m in each pane fixed to aluminium frame work with necessary glazing clips rubber packing/gasket, screws etc complete all as specified and as directed by Engineer-in-Charge.

S&F 12mm thick particle boards prelaminated on both side with teak wood finish as in panel of door shutters, partition wall, work stations incl beading etc complete all as specified.

M&L for powder coated aluminium frame (minimum thickenss of powder coating 50micron) work as in partition wall/door chawkhats/door shutters/sliding door chnannel using JINDAL section single groove any suitable section conforming to IS-733 and IS-1285 and opating grade A-153 conferming to IS-1868 fixed with rawl plug and screw or with fixing clips with expansion hold fastener including necessary jinting cleats, glazing clips, anodised aluminium snap beading packing, screws anodised aluminm fitting etc gap of junction at top, bottom sealed with PVC/Neoprene felt etc complete all as specified

S&F in repairs Safety lever locks brass Unilock/Dead lock with 6 levers as applicable and directed

S&F 200mm long Aluminium anodised,barrel tower bolts of extruded section .

S & F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed

Taking down old Aluminum window shutters size n.exc.1.5 sqm and M&L for complete overhauling of the sliding/hanging window roller and pivet replacement of glass pane/rubber beeding/aluminu glazing clip if necessary incl.necessary oiling and adjustment etc and refixing in sasme location complete all as directed. Note :- Glass Pane/rubberbeeding/aluminum beeding willbe measured and paid separately under subsequent items.

Taking down old Aluminum door shutters size exc.1.0 sqm but n. exc. 3 Sqm and M&L for complete overhauling of the door and door spring replacement of glass pane/rubber beeding/aluminu glazing clip if necessary incl.necessary oiling and adjustment etc and refixing in same location complete all as directed. Note :- Glass Pane/rubberbeeding/aluminum beeding willbe measured and paid separately under subsequent items.

S & F in repair rubber beeding to be fixed over glass panes in Aluminum doors complete all as directed.

Supply and fixing in repair aluminum anodised glazing clip/aluminum beading to the alumiinum door frames after fixing the glass panes complete all as directed.

Supply, fixing in repair aluminium Door seal complete all as specified & directed by engineer in charge .

S&F in repair Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; and similar work con- forming to Fe.290.Gde-E-165

S&F in repair glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket gurard and railing 60cm long tixed to plugs with chromium plated brass screws complete all as specified and direcgted

Taking down Chowkats or frames not exceeding 1.5 Sqm each including shutters without removing shutters from the frame complete all as specified and directed by Engineer in Charge.

Taking down shutter of any description exc 1 Sqmn.exc 2 Sqm complete all as specified and directed

S&F facrory made solid panel PVC door, shutter 30mm thick (Style consisting of frame out of MS tube fan top & bottom rail. MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20 mm wide stuck inside with solvent cement for stile and plain colour PVC sheet fan top rail, lock rail and bottom rail an either side as gap insert fan top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded sealded to the stiles and rails with suitable PVC sheet beading, and jointed together with. Solvent cement, suppling and fixing in the frame at site as per specified and directed at site.

S&F factory made PVC door frame of size 50mm x 47mm made out of 5mm plain colour PC|VC sheet re-inforced with MS square tube complete cell as spd.

S & F 35mm thick second class hard wood ,Glazed and skelton shutters , divided into into squares , with plain , chamfered or rounded , mitred and rebated sash bars ,any numbers , chamfered or rounded fitted with cut and mitred beads for securing glass , etc.: sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) ; supplied and fitted to chowkhats

S & F 30mm thick second class hard wood ,Glazed and skelton shutters , divided into into squares , with plain , chamfered or rounded , mitred and rebated sash bars ,any numbers , chamfered or rounded fitted with cut and mitred beads for securing glass , etc.: sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b) ; supplied and fitted to chowkhats

S & F 30 mm thick flush shutters , solid core construction , with block board core and plywood face panels , commercial type on both sides complete all as specified

S&F100mm butt hinges, extyruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed complete all as specified and directed

S&F Butt hinges 100mm size medium weight cold rolled mild steel and fixed complete all as specified and directed by Engineer in Charge.

S &f Aluminium anodised tower bolt of extruded section of 150 mm size all as specified

S &F Aluminium handles 150 mm size cast , anodised all as specified

S &f Aluminium anodised tower bolt of extruded section of 125 mm size all as specified

S &F Aluminium handles 125 mm size cast , anodised all as specified

S &F 3 mm thick Sheet glass , ordinary quality and glazing with oil putty in square n. exc. 0.5 sqm in each pane

S &F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks , or galvanised wire staples

Dismantling of floor , hearth , or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge

M &L Ceramic coloured/ printed non-skid tiles of size 7-8 mm thick( square / rectangular ) area of each tile exceeding 0.06 Sqm but n. exec. 0.11 Sqm laid as in floors setting and jointed with neat cement slurry over & including 15 mm thick screed bedding layers of cement sand mortar ( 1:4) and pointed with coloured cement to match with surfaces of tiles complete all as specified and as directed

M&L mirror-finished vitrified tiles (light shades) of 10 mm thick( square / rectangular ) area of each tiles 0.36 Sqm but n. exec 0.42 Sqm, in floors etc. set and jointed in cement slurrry laid over 15mm thick CM 1:4 (as/approved sample)and pointed in white or coloured cement to match all as specified .

M&L coloured Glazed Ceramic Tiles in vertical surface of Size 350x 250 x7 /450x350x7 mm set and jointed in neat cement slurry over 10 mm thick cement screed in cement mortar 1:4. and pointed in white or colour cement to match all as specified.

Demolition of stone slabs laid, bedded and pointed in any mortar of any description to floors, aprons etc complete all as specified and directed

M&L 20 Granite (of any type) work (table rubbed and polished, rounded and chamfered ) in steps, jambs, pillars, window- cills, cooking platforms and laid in 20 to 25mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for machine cut mirror polished kota stone slub of 20 to 25 mm thick liad in plat form over and including cemnet screed bed of 20 mm thick in cm 1:6, stone slub laId and jointed with grey cement slurry mixed with admix of pigment to match the shade / color / matrix of the slab incl rubbing and polishing incl one hole for gas pipe in platform as directed.

M&L Machine cut Kota stone slab flooring 20-25mm thick in slabs of size as approved by GE over 15mm thick cement screed base in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer in charge

M/L for kota stone slab 20-25 mm thick in riser of steps skirting dado and pippar laid over cement & screed 10mm th in CM 1:3 all as specified

M&L Preparation of new or previously untreated wooden surface ofany description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete.

Preparation of new or previously untreated steel surfaces of any description , over 10 cm in width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide all as specified

S&F Non- asbestos fibre cement buildings boards fixed or/laid/insrted to timber/GI/Aluminium frame work with screw.

M&L for anodised aluminium snap grid frame work for false ceiling incl necessary fixing material complete all as specified.

60. M&L White washing two coats as in new ceilings

Material & Labour for complete removal of existing treatment by washing down and smoothing old surface of walls including scrapping and applying two coats of oil bound distemper with smooth roller finish any floor incl Scafolding,complete all as specified and directed. (Note after painting ,cleaning of all floors,glass & furniture by own arrangement).

All as item No 1 above but on ceiling complete.

Please Enable Macros to View BoQ information