PROVN OF GUARD ROOM ALONGWITH TOILET BLOCK AT RA-16 (PINE ARTY OFFR MESS) OF 56 FD REGT UNDER GE (NORTH) MEERUT CANTT

Amount

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc.and getting out in Hard/ Dense soil complete all as specified and directed.

Excavating over areas, n exc 1.5 deep and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and directed.

Removing Excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M & L M-25 (using 20mm graded stone aggregate) for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns etc; basement slabs, under-reamed piles and mass concrete complete all as specified & directed.

M & L M-25 (using 20mm graded stone aggregate) for beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified & directed.

M & L M-25 (using 20mm graded stone aggregate) for columns, pillars, piers, posts and struts complete all as specified & directed.

M & L M-25 (using 20mm graded stone aggregate) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed.

Use & waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surfaces of concrete flat complete all as specified & directed.

Use & waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams rough finished surfaces of concrete flat complete all as specified & directed.

Use & waste formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete square or rectangular complete all as specified & directed.

Use & waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) rough finished surfaces of concrete flat complete all as specified & directed.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for TMT bars 6mm to 8mm dia and over as in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L damp proof course 40mm thick in cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) to horizontal or vertical surfaces including necessary formwork, polythene film 400 micron thick laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm complete all as specified & directed.

M & L for hard core of gauge not exc. 63mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M&L Plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling, mass concrete complete all as specified and directed.

M & L for 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 25 mm thick Cement concrete type-B-0 1:2:4 (using 12.5 mm graded stone aggregate) as subbase in floors complete all as specified and directed.

M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square / Rectangular)area of each tiles exceeding 0.18 sqm but not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles, laid over screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes Complete all as specified and directed.

M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square / Rectangular)area of each tiles exceeding 0.18 sqm but not exc 0.36 sqm in skirting set and jointed in neat cement slurry and pointed in coloured cement to match the tiles, over endering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 for backing of Dado/ Skirting & vertical Tiles Complete all as specified and directed.

M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square / Rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles, over screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes complete all as specified & directed.

M & L for glazed ceramic coloured / printed tiles 300mm x 450mm, 6 to 7mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/coloured cement to match the tiles,over backing coat of 10mm thick in cement mortar (1:4) for laying wall finishes complete all as specified & directed.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete all as specified & directed.

M&L brick work with sub class fly ash bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 complete all as specified & directed.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls, built in CM (1:6) complete all as specified and directed.

M & L for applying 15 mm thick rendering using ready mix plaster bags in CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, complete all as specified and directed. Note:- Water proofing compound shall be measured and paid seperately

Supply only integral water proofing compound complete all as specified & directed.

M & L for 15mm thick rendering in cement mortar 1:6, surface finished even & smooth (without using extra cement) on face of walls of brickwork or concrete surfaces complete all as specified & directed.

M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 and finished smooth and even in ceiling without ceiling using extra cement complete all as specified & directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall and applying two coats of weather proof exterior emulsion over a coat of primer complete all as specified and directed.

M&L for preparing newly plastered wall surfaces and applying three coat of white wash complete all as specified and directed.

M/L for preparing newly plastered ceiling surfaces and applying three coat of white wash complete all as specified and directed.

M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, frame rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F MS framed work such as grills, gratings,gates etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290-0 Gde E-165 complete all as specified and directed.

S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note :- (i) Rates inclusive of M.S. hold fast/ lugs or SS dash fasteners. (ii) For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as specified & directed.

Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S & F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 30 mm thick 2nd class hardwood glazed and skeleton window shutters rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.20(b); supplied and fitted in chowkats , but divided into squares, with plain, chamfered or roun ded, mitred and rebated sash bars, any numbers complete complete all as specified and directed.

S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F butt hinges, medium weight, Mild steel and fixed, size of hinges 75mm complete all as specified and directed.

S & F butt hinges, medium weight, Mild steel and fixed, size of hinges 100mm complete all as specified and directed.

Supply and fixing 100 mm mild steel pressed handles, oval type, stove enamelled black and fixed with screws, complete as specified and directed.

Supply and fixing 150 mm mild steel pressed handles, oval type, stove enamelled black and fixed with screws complete all as specified and directed.

S&F for mild steel barrel tower bolts stove enameled black, with bright bolt length of bolt 100 mm (ISI marked) fixed complete fixed with screws complete all as specified and directed.

S&F for mild steel barrel tower bolts stove enameled black, with bright bolt length of bolt 150 mm (ISI marked) fixed complete fixed with screws complete all as specified and directed.

Supply and fixing mild steel sliding door bolt 300 mm long (ISI Marked) stove enameled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts & nuts, four on bolt plate & two on staple plate with mild steel wood screws complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F floor door stopper of chromium plated body with rubber shoe fixed in door, overall length of cover plate 140 mm complete all as specified and directed.

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed.

S & F 3 mm thick Sheet glass, figured , pin headed and glazing with beadings in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S & F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty/or wooden beads in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with Stainless steel wire staples complete all as specified and directed.

M & L for painting to new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and directed.

Supplying and laying of 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches and wall complete all as specified. complete all as specified and directed.

S&F stop valves/angle valve, cast copper alloy, fancy type chromium plated with long shank & cup (concealed) , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore dia of pipe complete all as specified and directed.

S & F vitreous china wash basin, white, flat back, size 630X450 mm, (flat back or angle back type) including brackets and including cutting for and pinning in ends of brackets or erecting stand complete all as specified & directed.

S & F 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S & F bib taps, cast copper alloy, 15 mm dia, Chromium Plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and directed.

S&F vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests with 'P; or 'S' trap, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. in reapairs including Provn of lime concrete bedding and making good to floor complete all as specified & directed.

S & F 10 Liters capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia including brackets and connections to pipe complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints, fixed on walls or floors complete all as specified and as directed

S&F vitreous china urinals, full stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; with grating and union for discharge pipe, all as specified and as directed by Engineer-in-charge.

S&F 600mmx450mm bevelled edge looking mirror and fixed to wooden plug with CP brass screws and cup washers fixed on 6 mm thick AC Building board or commercial ply wood complete all as specified & directed.

M & L for 32mm bore high density polyethylene pipes (HDPE) complete all as specified and directed.

M&L for 75mm dia Cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 complete all as specified and directed.

S&F brass chromium plated tubular towel rail, 20 mm dia, D; type, 60 cm long between flanges complete all as specified and directed.

S&F Soap dish,vitreous china white, approximate size 160x160x90mm fixed to plug with chromium plated brass screws complete all as specified and directed.

S&F Chromium plated shower rose 125 mm with or without swivel joints, including fixing to steel pipe or union complete all as specified & directed.

S&F 25 mm dia curtain rod/harrison rails,mild steel, chromium plated fancy type fixed with end brackets, stops ,rollers & all connected accessories complete all as specified and directed.

S & F PVC connections 15mm dia , 450mm long, , with PTMT nuts & washers at both ends complete all as specified & directed.

S & F Rotational moulded PVC water storage tanks 500 Ltrs capcity three layer (cylindrical vertical with closed top) hoissted and fixed in position with inlet, outlet & wash out pipe complete all as specified & directed.

S and F Ball brass valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

Supplying and laying APP based modified water proofing polymeric membrane reinforced with non woven polyester fabric matt (weight not less than 150 gram/sqm) of minimum 3mm thick, weight not less than 3 Kg/sqm, laid over & including 15 mm thick rendering in cement mortar 1:4 on concrete surfaces, finished the surfaces even and smooth including mixing of water proofing compound @ 3% by weight of cement over a bituminous shalitex primer @ 0.30 Kg/sqm evenly over a coat of hot bitumen 85/25 @ 1.2 Kg/sqm. The membrane shall be unrolled and bonded completely to the substrate (with overlap of 100mm on the transverse direction and 75mm on longitudinal direction and sealed by thermos fused torch) and the overlaps sealed / fused by thermos fused torch as per manufacturer instructions. A coat of non reflective bituminous aluminium paint @ 0.150 Kg/ Sqm, complete all as specified and as directed Note :- Water proofing compound shall be measured & paid separately under respective items of BOQ

Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified & directed.

M&L for mild steel work in roof trusses,purlins,rafters,wind ties,crane gantries,posts,rails and fastenings and heavy bracket framing (Beam,Tee,Angle,Channel or Flat sections) including distance pieces,cleats etc complete all as specified and directed.

S&F MS plates (plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes, with fixing attachment,Fe-290(Gde E-165) complete all as specified & directed.

S&F Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self taping screws complete all as specified & directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L 75 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) finished fair and even as in sub base complete all as specified and directed.

M&L for chequred cement concrete tiles of size 300x300x25 mm thick coloured rubber pressed glossy finish, set and jointed in neat cement slurry and pointed in white or colour cement to match the surace of tiles in foor/steps, over 15 mm thick screed bed or bedding layer in CM 1:6 complete as all specified and directed.

M&L for Sand filling under interlocking tiles or in foundations including watering and consolidation complete all as specified & directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement complete all as specified and directed.

M&L for Providing cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in copings, platform, kerbs etc including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Removing Excavated soil exceeding 250 M but not exceeding 500M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

M & L for providing plain cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in coping, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M & L 150 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed as specified complete all as specified and directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150mm bore complete all as specified and directed.

M&L for Cement concrete 1:2:4 in haunching and benching for manholes complete all as specified and directed

M&L for RCC work type B-1 1:2:4 (20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, in shelves and precast cover slabs on manholes complete all as specified & directed.

Formwork to rough finished surface of concrete soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified & directed.

M & L for construction of Soakage wells , of size 2.40m dia & 6.00m depth ( effective depth 4.5 m ) in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM 1:4, RCC cover slab in M-25/ RR masonry / Filling with brick bats, all as including necessary earth work in any type of soil (soft / loose / hard / dense) all as shown on drg No TD-309 Sh. 1/4 to 4/4. complete all as specified and directed.

M&L for construction of septic tanks, foundation in PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc., for 25 users including necessary earth work in any type of soil (soft / loose / hard / dense) all as shown on drg No TD-217 sheet 1/7 to 7/7 complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness.(below or above ground level) Complete all as specified and directed.

Surface channel in concrete 1:3:6 (40 mm graded aggregate) for drain including necessary formwork complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement complete all as specified and directed.concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm (nominal cross section area) single core, multi stranded PVC insulated, unsheathed copper conductor, FR cable in and including in rigid pvc conduit 20 mm dia or higher medium grade ISI marked complete with all PVC Conduit accessories / fittings and sunk pressed (1.2 mm thick) steel terminal switch boxes with 3 mm thick plastic laminated hard glossy surface sheet top cover, including earth wire continuous of PVC insulated, unsheathed 1.5 Sqmm copper conductor, PVC insulated connected to all fittings, sunken boxes and common earth, earth dolly. Plastic sheet screwed with brass screws, cup washers complete all as specified and directed for the following:-

One light/Bulb/ street light pointcontrolled by one, one way switches 5/6 Amps complete all as specified and directed.

One 3 pin 5/6 Amps socket outet point on independent board, controlled by one, one way 5/6 Amps switch complete all as specified and directed.

One 3 pin 5/6 Amps socket outet point on same board, controlled by one, one way 5/6 Amps switch complete all as specified and directed.

M&L for point wiring with 2.5 Sqmm (nominal cross section area) single core, multi stranded PVC insulated, unsheathed copper conductor,FR, cable in and inrigid pvc conduit 20 mm dia or higher medium grade ISI marked complete with all PVC conduit accessories / fittings and sunk pressed (1.2 mm thick) steel terminal switch boxes with 3 mm thick plastic laminated hard glossy surface sheet top cover, including earth wire continuous of PVC insulated, unsheathed 2.5 Sqmm copper conductor, PVC insulated connected to all fittings, sunken boxes and common earth, earth dolly. Plastic laminated sheet screwed with brass screws, cup washers complete all as specified and directed for the following :- (a) One 3 pin socket outlet, 15 amps, with cables 2.5 sqmm size on independent board, controlled by one, one way 15 amp switch.

S&F Modular Switch , 1 Module , 6A, AC, 240 V. one way ISI Marked and complete all as specified and directed.

S&F Modular Socket , 2 Module , 6A, 2/3 pin combined , AC, 240 V. ISI Marked and complete all as specified and directed.

S&F Modular Socket, 2 Module , 6A/16A, 2/3 pin combined , AC, 240 V. ISI Marked and as specified

S&F Modular Switch ,1 Module , 16A, AC, 240 V. ISI Marked and complete all as specified and directed.

S & F ceiling rose, surface type, bakelite, 65 x 50 mm, three terminal complete all as specified and directed.

Supply & fix LED lamp 9 W 6500k,240V complete all as specified and directed.

S & F lamp holder insulated body with back plate fix done anodised 100 x 100 mm pressed steel box flush to the wall with 3 mm thick backlite cover complete all as specified and directed.

Supply & fixing LED tube light fitting T/5 surface mounting poly carbonate 240 volts 20 watts, 6500K complete all as specified & directed.

M&L for Building security light fitting 1 x 35 LED type, drawn through and including GI bracket of size 25 mm dia bore light grade 1.4 mtr long, bend to shape including MS clamps made out of flat iron of size 32 x 4 mm - 02 Nos and necessary nuts, bolts, washer as required complete all as specified and directed.

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 8 way with 200 Amp rated bus bar flush /surface mounting double door complete all as specified and directed.

Supply and fix MCB single pole 240 volt 6 to 32 amps 10 KA complete all as specified and directed.

Supply & fixing Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&L XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volt grade cross sectional area of 16 sqmm 2 core complete all as specified and directed.

Material and labour for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable with and including continuous earth wire of size 06 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including taking down old u/s wiring & incl all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed.

S&F Isolator DP 40 Amp ,240 Volts, suitable for fixing in MCB DB 'C' series in DB complete all as specified and directed.

M/L for Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 Mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead wite 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specifiied or indicated including testing on completion complete all as specified and directed.

S&F Exhaust fan, steel body AC single phase, 230V of size 300 mm sweep with blades,frame and louvers complete all as specified and directed.

Supply and fix Water heater storage type steel body with copper inner tank and heating element upto 2KW capacity 25 ltr, BEE 5 stared complete with a rating including providing of hold fast in wall and PVC connection 45 cm long with 15 mm dia brass union at both end heavy duty complete all as specified and directed.

All as per item No-1 here-in-before but depth exceeding 1.5 mtr wide and n. exc. 3 mtr complete all as specified and directed.

M & L for Sand cushioning for under ground cable upto 8 cm before laying the cable and 15 cm after laying cable and then punned. After punning the thickness of sand cushioning should be 18 cm complete all as specified and directed. Note :- Only punned thickness shall be measured for payment.

Material and labour for sub class 'B' bricks well burnt of size laid dry flat for width wise protection of cable complete all as specified and directed.

Supply and laying in trenches through pipe or under culvert of XPLE insulated PVC sheathed heavy duty 1100 volts grade of size 16 sqmm, 4 core with stranded aluminium conductor including proper connection to LT panel /bus bar with aluminium thimbles of suitable size /rating and taking down the old unserviceable cable complete all as specified and directed by Engr-in-charge.(Note – necessary excavation, returning filling,removal of soil ,sand cushioning,brick work and GI pipe shall be measured and paid under respective item of Sch).

M & L for GI pipe ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including suitable size clamps complete of size 40 mm bore complete all as specified and directed.

M & L Gun metal gate valve with iron wheel head screwed both ends for iron pipe including testing of following :-

50 mm dia bore complete all as specified and directed.

25 mm dia bore complete all as specified and directed.

20 mm dia bore complete all as specified and directed.

Cutting of existing CI pipes and reducing to required length before laying in position for insertion of new tees,branches etc complete all as specified and directed of size 150mm dia bore. Note :- Fittings will be measured and paid foe separately under respective items.

S & F GI tubing,medium grade,ISI marked complete with all fittings laid in trenches or laid under floors,fixed on walls on walls with and providing clamps etc complete all as specified & directed for the folloeing size :-

50 mm dia bore complete all as specified and directed.

25 mm dia bore complete all as specified and directed.

20 mm dia bore complete all as specified and directed.

Shri Kanchan Engineers (BID ID -3485375)