REPAIR/ REPLACEMENT OF B/R NATURE OF WORKS AT VASANT RANGE COLONY AND PETTY REPAIRS TO B/R WORKS OF 10 JAK LI UNDER AGE B/R-I (S) OF GE (SOUTH) DELHI CNATT-10

Amount

Demolition brick work built in cement morter or cement motar complete all as specified and directed by Engineer-in-charge.

Taking down cement or cement lime plaster on brick or stone walls build in cement mortar including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

Demolition of PCC in ground floors and pavings n'exc 15 cm thick below or above ground level (unreinforced) complete all as specified and directed by Engineer-in-charge.

M&L for brick work with sub class' B' old size bricks straight or curved on plan exc. 6m. mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge.

All same as per item No 4 but except bricks

M&L for brickwork with sub class 'B' bricks straight/curved on plan to any radius in half brick thick walls built in cement mortor 1:4 in brick walls complete all as specified and directed by Engineer-in-charge.

M&L for rough cast plaster over 15mm thick rendering on brick work or concrete surface in cement mortar (1:4), surface finished complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar (1:6), surface finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for cement concrete 75 mm thick type D-2, 1:4:8 (using 40 mm graded stone aggregate) complete all as specified and directed by Engineer-in-charge.

S&F in repairs , 60 mm thick vibrated machine pressed cement concrete interlocking paver solid blocks any shape and size confirming to IS -15658-2006 M-25 grade with grey cement and no pigment laid over 30mm sand cusion and joint filled with sand complete all as specified and directed by Engineer-in-charge. Make - A-ONE, HINDUSTAN, NITCO

S&F in repair block board grade 2 quality , exterior grade commercial type 18/19 mm thick in copboard shutter & partitions including 0.90 mm thick decorative laminate type 1 on one side surface finish of colour and pattern as approved fixed with approved adhesive complete all as specified and directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-charge.

M&L for coloured lazed ceramic tiles jointless 350x250mmx7mm/450X300X7mm thick on vertical surface as in dados set and jointed in neat cement sturry and pointed in coloured cement to match over and including rendering 10mm thick with CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L for Non Skid ceramic joint free tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchset & jointed in neat cement slurry & pointed in coloured cement to match over and including 15mm thick screed bed in cm 1:6 for laying floor finish complete all as specified and directed by Engineer-in-charge.

All same as per ser item No. 14 above item but on skirting & including taking down plaster / old skirting

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:6) complete all as specified and directed by Engineer-in-charge.

All same as here in before item 16 but as in skirting over 10 mm thick rendering in CM 1:4 complete all as specified and directed by Engineer-in-charge.

Taking down shutter and refixing in same opening after necassary bottom rail cutting exc 1 sqm and n exc 2 sqm each complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces on walls complete and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces on walls complete and applying two coats of cement based paint complete all as specified and directed by Engineer-in-charge.

M&L for Chequered cement concrete tiles 25cm x 25cm x 22 - 25mm thick, set, jointed and pointed in near cement slurry in floors with grey cement without pigment laid on screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and directed by Engineer-in-charge. Make:- Hindustan Tiles, Mehatab Tiles, Nitco tiles.

M&L for PCC 1:2:4 type B-1 ( 20mm graded agg) cement concrete in roof kerbs of mud stops, rounded or chamfered on edges complete all as specified and directed by Engineer-in-charge.

M&L for 15-17 mm thick marble (Green) udaipur machine cut bedded jointed & pointed with grey cement slurry including cutting & polishing over 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L for PCC 1:3:6 type C2 using 40mm stone aggregate as in bed of drain etc. all as specified complete all as specified and directed by Engineer-in-charge.

S&F in repair stainless steel sink with drainage board of 1 mm thick sheet for kitchen with plug washer, waste pipe, cast iron cantilever brackets connecting union, fixed in position complete all as specified and directed by Engineer-in-charge.

S&F in repairs stainless steel sink with out drainage board made out of ,304 grade Stainless steel,1.00 mm thick sheet for kitchen with cantilevers connecting union complete all as specified and directed by Engineer-in-charge.

S&F in repairs 0.8mm thick stainless steel plate rack overall size (31X36X10 inch) fixed with steel screws complete all as specified and directed by Engineer-in-charge.

S&F in repair for vitreous china wash hand basin flat back size 550x400 mm size white excluding taps waste chain and plug and porcelain stopper but including brackets and 32 mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32MM X 600 MM long PVC waste pipe complete flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-charge.

S&F in repair Chromium plated Pillar tap 15 mm bore cast copper alloy with capstan heads chromium plated screwed down high pressure screwed in iron pipe complete all as specified and directed by Engineer-in-charge.

S&F in repair chromium plated bib tap long body with flange fixed in 15mm bore of pipe, cast copper alloy with crutch or butterfly handle, screwed in iron pipe complete all as specified and directed by Engineer-in-charge.

S&F in repair bib tap ISI marked cast copper alloy with crutch or butterly handle screwed down high pressure and screwed down for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-charge.

S&F in repair bib tap standard 15 mm dia of PTMT any colour for iron pipe and fixed (Minimum weight 90 gms) complete all as specified and directed by Engineer-in-charge. (Make :Polyplast/Symet/Prayag).

S&F in repair PVC connection 15 mm dia 45 cm long with 2 Nos PVC check nuts with washer complete all as specified and directed by Engineer-in-charge.. (Make :Polyplast/Symet/Prayag).

S&F in repair chromium plated Stop valve/angle valves cast copper alloy, screwed down both ends high pressure, with crutch or butterfly handle, screwed both end fixed, 15mm internal bore complete all as specified and directed by Engineer-in-charge.

S&F in repair chromium plated brass overhead shower with arm 255mm with flange with swivel joints, any size, including fixing to steel pipe or union for 15mm bore pipe complete all as specified and directed by Engineer-in-charge.

S&F in repair 32 mm to 40mm dia PVC waste pipe for WHB & sink, 60 cm long with union complete all as specified and directed by Engineer-in-charge.(Make : Poly Plast/Symet/Prayag).

S&F in repair brass jumper washer, brass head, face and spindle for bib cock/pillar cock/stop cock 15 mm bore any type complete all as specified and directed by Engineer-in-charge.

S&F in repair waste fittings brass chromium plated 32 mm dia for wash hand basin complete all as specified and directed by Engineer-in-charge.. (Make : ZIM / PARKO/GMG)

S&F in repair 10 ltrs capacity PVC Low level flushing cistern including PVC syphon and float valve with float, PVC long bend for out let connection of cistern with WC complete fixing and connecting bend with WC complete all as specified and directed by Engineer-in-charge.

S&F in repair plastic water closet seat cover (for Anglo Indian) white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium anodised hinging device complete all as specified and directed by Engineer-in-charge.

S&F in repair CP grating 127 mm dia with/without hole round, fixed on floor / nahani trap, fixed with cement mortar(1:3) complete all as specified and directed by Engineer-in-charge.

S&F in repair HDPE PVC lid (cover) for 500 Ltrs capacity PVC tank complete all as specified and directed by Engineer-in-charge.

S&F in repair sliding door bolts 300 mm long clip type stove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repair MS barrel tower bolt, stove enamelled black 200mm long complete all as specified and directed by Engineer-in-charge.

S&F in repair 100 mm long MS butt hinges 'medium weight' cold rolled welded to steel frame work complete all as specified and directed by Engineer-in-charge.

S&F in repair steel window handles(right & left) and peg stays etc as per sample complete all as specified and directed by Engineer-in-charge.

S&F in repair 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed by Engineer-in-charge.

S&F in repair 125 mm mild steel pressed handle oval type, stove enamelled black complete all as specified and directed by Engineer-in-charge.

S&F in repair 125 mm aluminium anodised handle cast type, complete all as specified and directed by Engineer-in-charge.

Refixing the old GI steel water tubing and connection of 15mm bore in new / old position with and including all fittings, to roofs,walls or ceiling as directed after taking up or down old GI steel water tubing 15mm bore and connections including cleaning complete all as specified and directed by Engineer-in-charge.

Refixing the old GI steel water tubing and connection of 20mm bore in new / old position with and including all fittings, to roofs,walls or ceiling as directed after taking up or down old GI steel water tubing 15mm bore and connections including cleaning complete all as specified and directed by Engineer-in-charge.

Refixing the old GI steel water tubing and connection of 50mm bore in new / old position with and including all fittings, to roofs,walls or ceiling as directed after taking up or down GI steel water tubing 15mm bore and connections including cleaning complete all as specified and directed by Engineer-in-charge.

S&F galvanised steel water tubing 15mm bore 'medium grade' with and including all fittings and fixed to walls or laid in floors complete all as specified after taking up or down old GI steel water tubing 15mm bore and connections including cleaning complete all as specified and directed by Engineer-in-charge. (Make : Jindal/Prakash)

S&F galvanised steel water tubing 20mm bore 'medium grade' with and including all fittings and fixed to walls or laid in floors complete all as specified after taking up or down old GI steel water tubing 15mm bore and connections including cleaning complete all as specified and directed by Engineer-in-charge.. (Make : Jindal/Prakash)

S&F galvanised steel water tubing 50mm bore 'medium grade' with and including all fittings and fixed to walls or laid in floors complete all as specified after taking up or down old GI steel water tubing 15mm bore and connections including cleaning complete all as specified and directed by Engineer-in-charge. (Make : Jindal/Prakash)

S&F rotational moulded polyethelene water storage tank triple layered capacity 500 litres 'ISI Marked' cylindrical vertical with closed top hoisted and fixed in position including Dismantling water tanks exc 250 litre but not exceeding 500 litre and removal from site complete all as specified and directed by Engineer-in-charge. Make:- Polywell/Sintex/Rotex.

S&F in repair vitreous china squatting pan (Orissa pattern white) long pan fixed size 580x440mm white with integral footrest with 100 mm bore Cast iron `P' or `S' trap complete (excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer-in-charge.

S&F in repairs viterous china wash down water closet pan Pedestal pattern (Anglo Indian WC) white incl 'P' or 'S' trap and making good the disturbed surface to match with the existing ccomplete all as specified and directed by Engineer-in-charge.

S&F in repair, 25 mm bore mild steel 0.8mm thick conduit pipe with PVC ribbed lamination of required length for curtain rods including two fixing mild steel powder coated matching colour full round or half round with fixing nuts (bracket holders),& PVC golden finish end knobs(Two numbers for each curtain rod of any length) and PVC gold finish curtain ring @ 3 nos/feet complete all as specified and directed by Engineer-in-charge.

S&F in repair, Aluminium sheeting 0.50 mm thick, fixed to wooden shutters with CP screws including cutting to required size etc complete all as specified and directed by Engineer-in-charge.

S&F in repair mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tracks or galvanised wire staple and complete all as specified and directed by Engineer-in-charge. .

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 sqm in each pane including hacking out old broken glass of any thickness/size of any description from steel / wooden frame glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-charge.

S&F 4mm thick Figured glass ,pin head type and glazing with oil putty in sqr n exc 0.5 sqm in each pane etc including Hacking out old broken glass of any thickness/size of any description from steel / wooden frame glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-charge.

M&L for welding in repair in any situation and in any position such as hinges and similar articles etc for steel door, gates, window, ventilatiors and grills etc for upto four stoery building complete all as specified and directed by Engineer-in-charge.

Taking down rain water pipes (any size or pattern) including all fittings bends etc complete all as specified and directed by Engineer-in-charge.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, 110mm bore of pipe complete all as specified and directed by Engineer-in-charge.

S&F PVC (SWR) bends any radius for 110mm bore of pipe complete all as specified and directed by Engineer-in-charge.

S&F PVC (SWR) bends any radius for 75 mm bore of pipe complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete in ground floor and paving etc not exc 15 cm thick above or below ground level complete all as specified and directed by Engineer-in-charge.

M&L for PCC (1:2:4) Type B-1 (using 20 mm graded stone aggregate), 40 mm thick as in floors etc finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for PCC (1:3:6) type C-2 (using 40 mm graded aggregate) 75 mm thick as in floor / plinth protection finished even and smooth w/o using extra cement complete all as specified and directed by Engineer-in-charge.

Cleaning and removing all scales and dirt etc from existing tanks and from mouths of circulating pipes etc for exceeding 250 litres but not exceeding 500 Litres capacity of tanks complete all as specified and directed by Engineer-in-charge.

Cleaning and removing all scales and dirt etc from existing tanks and from mouths of circulating pipes etc for exceeding 500 litres but n.exc 2000 Litres capacity of tanks complete all as specified and directed by Engineer-in-charge.

M&L for cutting trees including cutting of trunks and branches and digging out roots from floor or roof and walls making good the dismantled portion in cement mortar (1:3) girth of trees 30 cm, complete all as specified and directed by Engineer-in-charge.

Taking down cast iron pipes including fittings by burning out lead joints etc to facilitate dismantling old serviceable fittings/pipes laid in trenches,floors or fixed to walls all as directed including earth work, demolition of PCC / Brick work complete all as specified and directed by Engineer-in-charge for the following sizes of pipes:-

100 mm bore of pipe.

75 mm bore of pipe.

S&F 75 mm bore cast iron, sand cast ,soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-charge.

S&F 100 mm bore cast iron, sand cast ,soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to wall complete all as specified and directed by Engineer-in-charge.

S&F in repairs 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-charge.

S&F in repairs 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-charge.

S&F repairs branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches for 75 mm bore pipe complete all as specified and directed by Engineer-in-charge.

S&F repairs branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access door for 100 mm bore pipe complete all as specified and directed by Engineer-in-charge.

S&F in repairs cast iron floor trap/nahani trap incl stainless steel gratings, 75 mm dia of outlet, including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and directed by Engineer-in-charge.

S&F in repair 15mm dia stop valve concealed type cast copper alloy, screwed down, high pressure chromium plated with long shank including making good dismantled portion complete all as specified and directed by Engineer-in-charge.. (Make : ZIM / PARKO/GMG)

S&F in repair gun metal globe or gate valve 'ISI' MARKED, with iron wheel head screwed both ends and for iron pipes and fixed for bore of pipe 15 mm complete all as specified and directed by Engineer-in-charge.

S&F in repair gun metal globe or gate valve 'ISI' MARKED, with iron wheel head screwed both ends and for iron pipes and fixed for bore of pipe 20 mm complete all as specified and directed by Engineer-in-charge.

S&F in repair small fittings galvanised iron 'medium grade' such as socket, elbow, nipple of any length upto 150mm long, Tee, union etc for 20 mm bore pipe (ISI marked) complete all as specified and directed by Engineer-in-charge. (This item will not be measured against item No.44 &47 here in after).

S&F in repair small fittings galvanised iron 'medium grade' such as socket, elbow, nipple of any length upto 150mm long, Tee, union etc for 15 mm bore pipe (ISI marked) complete all as specified and directed by Engineer-in-charge. (This item will not be measured against item No.43 &46 here in after).

S&F in repair CI bracket of exiting size, for WHB or Kitchen Sink etc including cutting, necessary fitments for pinning in brackets complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC syphone with handle complete for low level flushing cistern complete all as specified and directed by Engineer-in-charge. (Make: Superflush/ISI marked).

S&F in repair PVC handle heavy duty, for low level flushing cistern complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC polyplast float valve for cistern tank complete all as specified and directed by Engineer-in-charge.

S&F in repair soap dish Chromium plated brass fancy type complete all as specified and directed by Engineer-in-charge.

S&F in repair , CP towel rail 60Cm long complete all as specified and directed by Engineer-in-charge. Make: Prayag/Cera/Parryware.

S&F in repair glass Shelf Corner with frame Chromium plated brass fancy type complete all as specified and directed by Engineer-in-charge. Make:- Prayag/Cera/Parryware.

S&F in repair HDPE PVC lid (cover) for 1000 to 2000 Ltrs capacity PVC tank complete all as specified and directed by Engineer-in-charge.

S&F in repair CP Peg set of 06 hanging complete all as specified and directed by Engineer-in-charge. Make:- As per sample available with Engineer-in-charge

S&F in repair, MS clamps for CI pipes 100 mm bore made out of 50mm x 5 mm flat and 16 mm dia round bars, including bolts and nuts and securing to wall in PCC (1:2:4) and making good in cement mortar (1:3) complete all as specified and directed by Engineer-in-charge.

Attending complaint for petty repair to leaking water in bib tap, pillar tap, stop cock, angle valve, flushing cistern, WHB, Sink, wall mixer etc. of any description any size by changing the washers(s)/jumper(s) etc, by adjusting/replacing the washer(s) and adjustment of lever required for making the flushing cistern functional, by tighting the leaking waste pipe of WHB/Sink and providing 'M' seal to stop leakage as required. Removal of air lock/blockage of water in GI water tubing and cleaning the pipe or fittings etc. including replacement of major defective item if required, complete all as specified and directed by Engineer-in-charge. Note 1 :- The contractor shall make all arrangement for attending the different types of complaints on every day basis.Any major item required to be replaced with new one, to make the system functional shall be measured and paid for seprately as " S & F" under respective applicable item of this schedule. Old retrived item (s) as considered in 'Schedule of Credit' shall become property of the contractor. Note 2 :- Contractor shall provide minimum one plumber with helper for VRC and 10 JAK LI including all necessary T & P on all working days from 9AM to 5 PM .Additional workers can be engaged if nature of work required to be completed with in fixed time as desired by GE . Rate shall be quoted accordingly . Keeping in mind above said provisions. Note 3 :- Where material provided shall be paid as " S&F underrespective item of Sch. 'A' the payment of complaint under this item shall not be paid. 4. Proper records (date wise) of complaints received & rectified by the contractor and attendance register of trademen shall be maintained and shall be produced for verification at the time of payment of each RAR/Bill..

S&F in repair waste fittings brass chromium plated 40 mm to 50 mm dia for stainless steel sink complete all as specified and directed by Engineer-in-charge.

S&F in repair small fittings galvanised iron 'medium grade' such as socket, elbow, nipple of any length upto 150mm long, Tee, union etc for 50 mm bore pipe (ISI marked) complete all as specified and directed by Engineer-in-charge. (This item will not be measured against item No. 44 & 48 here in after).

S&F in repair CP Health faucet for Europeon type WC with 1.5m long pipe as per approved sample complete all as specified and directed by Engineer-in-charge.

S&F in repair chromium plated Jet for WC with 1.00 Mtr long PVC pipe including necessary GI fitting as required like toe, nipple etc complete all as specified and directed by Engineer-in-charge.

S&F in repair , Toilet paper holder Chromium plated brass fancy type complete all as specified and directed by Engineer-in-charge or equivalent Make of Prayag/Cera/Parryware.

S&F in repair , towel ring chromium plated brass fancy type complete all as specified and directed by Engineer-in-charge. or equivalent Make of Prayag/Cera/Parryware.

Attending complaint for petty repair to easing of Doors/Window/Cup Board shutters by tightening of hinges / handles / Al-drop bolt / tower bolt / knobs, hasp and stapple etc of any size / any number of panels for easy closing / opening or changing the position of hinges, adjustments of tower bolts,sliding bolts, replacement of looking mirror etc complete including replacement of major defective item if required, complete all as specified and directed by Engineer-in-charge. Note 1 :- The contractor shall make all arrangement for attending the different types of complaints on every day basis.Any major item required to be replaced with new one, to make the system functional shall be measured and paid for seprately as " S & F" under respective applicable item of this schedule. Old retrived item (s) as considered in 'Schedule of Credit' shall become property of the contractor. Note 2 :- Contractor shall provide minimum one Carpenter with helper for VRC and 10 JAK LI including all necessary T & P on all working days from 9AM to 5 PM .Additional workers can be engaged if nature of work required to be completed with in fixed time as desired by GE . Rate shall be quoted accordingly . Keeping in mind above said provisions. Note 3 :- Where material provided shall be paid as " S&F underrespective item of Sch. 'A' the payment of complaint under this item shall not be paid. 4. Proper records (date wise) of complaints received & rectified by the contractor and attendance register of trademen shall be maintained and shall be produced for verification at the time of payment of each RAR/Bill..

M&L for manual Sealing of traps,WCs (manually) with neat cement paste after removal of water from it, to prevent or make up the leakage including cementing in cement mortar (1:3) from inside and outside both & refixing grating, plasters etc complete all as specified and directed by Engineer-in-charge.

Extra over cast iron pipe and fitting if lead joint are provided in lieu of cement joints complete all as specified and directed by Engineer-in-charge for the following sizes of pipes:-

100 mm bore of pipe.

75 mm bore of pipe.

M&L for 10 mm thick plaster in cement mortar (1:4) not exceeding 3 sqm each patch, on ceiling, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge

M&L for preparation of plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-charge

Cleaning and removing all scales and dirt etc from existing tanks and from mouths of circulating pipes etc for exceeding 2000 litres but n.exc 4000 Litres capacity of tanks complete all as specified and directed by Engineer-in-charge

M&L for prepration of new wood or wood based surface not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated plastered or plastered wall surfaces including pilasters and cornices etc including brooming down or steel wire brushing and applying one coat of white lime wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated plastered / concrete wall surfaces including brooming down or steel wire brushing and applying two coats of white lime wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated plastered / concrete ceiling surfaces including brooming down or steel wire brushing and applying one coat of white lime wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated plastered wall surfaces including plasters and cornices etc including brooming down or steel wire brushing and applying one coat of oil emulsion distemper, white or tinted ( Colour & shade shall be as approved by the GE ) complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated wooden or wood based surfaces of any description not otherwise described, over 10 cm width or girth, and applying one coat of synthetic enamel paint ( 1st Quality) white or tinted (Colour & shade shall be as approved by the GE) complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated steel surfaces of any description not otherwise describe, over 10 cm width or girth, and applying one coat of synthetic enamel paint ( Ist Quality) white or tinted( colour & shade as approved by GE) complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frames with shutter exc 1.5 sqm and nexc.4.00 Sqm each but without taking off shutters from the frame complete all as specified and directed by Engineer-in-charge.

Taking down shutter of any description exc 1.00 sqm nexc 2.00 sqm each complete all as specified and directed by Engineer-in-charge.

S&F powder coated aluminium window with single side hung shutters for glazing and frames with suitable rebates made out of JINDAL/ INDAL anodised aluminium sections including section require for fixing of aluminium grill and including jointing cleats for fixing clips, rubber packing, powder coated aluminum beading, screws and powder coated aluminium fittings such as peg stays, SS hinges (type B-20) 100mm long, suitable handle, glazing with 6 mm thick tinted sheet glass (tint of glass as approved by GE) complete all as specified and directed by Engineer-in-charge. (Aluminium grill shall be measured and paid separately).

S&F powder coated aluminium fully glazed door with shutter fixed with hydraulically operated floor spring and frame with one or more rebates made out of JINDAL/INDALaluminium sections, shutters fixed with hydraulically operated floor spring including jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading, screws and powder coated aluminium fittings, with panel of 6.0 mm thick tinted glass (tint of glass as approved by GE) complete all as specified and directed by Engineer-in-charge.

M&L for 35mm thick 2nd class hardwood glazed and skelton shutter open rabated and prepare to receive gauge etc divided into square with plain, chamfered or rounded fixed with cut : mitered beads for receiving gauge etc complete all as specified and directed by Engineer-in-charge.

S&F 35mm thick plain framed 2nd class hardwood panelled shutter (two panels ) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle with commercial veneering on both face, the size of rail and style as per IS 1003 (Part-1) kiln seasoned and chemically pressed, treated complete incl 15 to 20 mm tapering bedding on one face of second cl hardwood fitted to chowkhats complete all as specified and directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be coloured with heat mould plain coloured PVC'C channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stills and plain colour PVC sheet for top rail lock and botton rail either side and as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed by Engineer-in-charge.

S&F solid PVC doors & frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm MS square tube of 19 guage S&F in opening as per specification & drg in SSR 2004 Part II complete all as specified and directed by Engineer-in-charge.

M&L for 25 mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded aggregate in sub base of floors etc complete all as specified and directed by Engineer-in-charge.

M&L for coloured /light shade vetrified ceramic tiles 10mm thick (square/regtangular) polished , area of each tiles not exc 0.36 sqm in floors etc and joineted neat in cement slurry and pointed in white or colour cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-charge.

Note:- The contract sum shall be after deducting the amount of Credit shown in Credit Schedule of this Tender.

M/S.Parmod Johar

M/S Davinder Kumar

Chaudhary Constructions

Deep Contractor

SRI RAM RAJ DEYEE CONSTRUCTION COMPANY