SPL REPAIR TO RAINA AUDITORIUM OF CORPS HQ COMPLEX UNDER GE 865 EWS

Amount

Dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and as directed

Dismantling unframed timber scantling under 40 sqcm in section, in fillets, rails, posts, rafters, purlins etc at any position, complete all as specified and as directed.

M&L for wooden floor tiles 7 mm thick with dove tailed joints laid over 150 micron polythene film and 3 mm thick foam as per manufacturer's instructions, including taking down of old wooden flooring and fixed with decorative wooden beadings as per site requirement including taking down of wooden floor tiles any type complete all as spfd and directed.Make and shade of tiles be all as approved. Make : Action tesa/Kajaria/Armstrong

S & F gypsum ceiling board 10mm thick in 600 x 600 mm pannel designer ceiling conforming to IS-14862 type B category three including suspended false ceiling using E-grid suspended ceiling grid system of grid size 600x600mm with GI frame work of main runner 38 x 24mm sheet thickness 0.4mm, cross Tee 28 x 24mm sheet thickness 0.3mm and wall angle 24 x 24mm to be placed in the grid suspended by 4mm GI wire hanger to be fixed as per site requirement including taking down of old false ceiling complete. MAKE : EVEREST/ARMSTRONG/GYPROC

S&F of wooden panelling on vertical surface of wall using following specifications including taking down old wooden paneling complete all as specified and directed:- (a) S&F Iind class hard wood wooden gutties of size 25mmx25mmx200mm depth fixed in wall by making holes in brick wall and making good in cement mortar 1:3. (b) S&F horizontal rummer Iind class soft wood(Kali( at 120 c/c of sextional area exc. 13 Sqm and n. exc 25 Sqm clean sawn treated with two coats of creoste oil mixed with good quality pesticide for antitermite treatment. (c) S&F 1st cl soft wood (Deodar) boarding 12mm to 15mm thick as in wall panelling planed one side, wrought and other side clean sawn and applying two coats of good quality varnish on plain surfaces ofve a coat of primer mixed with good quality pesticide for antitermite treatment on the other side and fixed with screws/nails on wooden runners. d) S&F 1st class soft wood(Deodar) decorative breading 40mm wide on top surface of wall panelling including two coats of vernish.

S&F Anodised aluminium snap grid frame work (size of grid 605 X 605 mm) for false ceiling including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed by Engr-in-Charge.

M& L for 12 mm thick perforated particle board/tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid and fixed in ceiling, flat or sloping complete all as specified.

M&L for 12 mm thick perforated particle board/tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails to timber frame work as fixed in walls complete all as specified and directed by Engr-in-Charge.

M& L for 2nd class soft wood clean sawn as in battens for grid of wall lining and plain fillets. square, rectangular or triangular in section, secured with nails or brads exc 13 sqcm and n .exc 25 sqcm in section complete all as specified and directed by Engr-in-Charge.

6mm thick veneered particle boards interior grade, solid core, with decorative face veneers on one side fixed with screws to timber frame work including taking down of old u/s board complete all as specified and as directed by Engr-in-Charge. MAKE: NOVA PAN/GREEN PLY BHUTAN BOARD/MYSORE WOOD BOARD/CENTURY PLYWOOD

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tile to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and Removing demolished material to a distance and depositing out site of MoD land where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engineer-in-Charge.

25 mm thick, plain cement concrete, 1:2:4 (Nominal Mix), type B-0 (using 12.5 mm graded crushed stone aggregates) as in floors finished rough surface to receive floor finishes, complete all as specified and directed by Engr-in-Charge.

M & L for joint free Non-Skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:6 for laying floor finishes complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for (350mmx250mmx7mm/450mmx350mmx 7mm thick ) coloured glazed ceramic tiles set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments.(Note: Any disturbed surfaces shall be matched w/o any extra cost to the govt) incl 10mm thick rendering in CM 1:4 below tile for dado/skirting complete all as specified and directed by Engr-in-Charge. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for vitrified ceramic tiles 10mm thick (light shade ) (square/rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and screed bed with CM (1:4) 15mm thick for laying floor tiles all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for Granite (of any type) tiles 20mm thick machine cut, in steps, jambs, pillars, window-cills, cooking platform and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid over and including 20 mm thick cement screed bed in CM 1:6 including demolition of stone slabs and tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. ), complete all as specified and directed by Engineer-in Charge.

Taking down Shutters of any description exc 2 Sqm each, complete all as specified and directed.

M&L 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the soild, rounded or chamfered, put together with glue pinned at joints, supplied and fixed plain fillets, square, rectangular or triangular in section clean swan, secured with nails or brads complete all as specified.

S&F for factory made 35mm thick 1st class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass/gauge etc divided into squares, with plain , chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of door shutters as specified in SSR Part-I sec 8 clause 8.24 (a), fixed to chowkhat all as specified and as directed by Engineer-in-Charge. MAKE: M/S WOOD PRODUCT INDORE/M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI/ M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT/M/S PIONEER TIMBER PRODUCT CHANDIGARH/M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU/M/S M.S JOINERY WORKS, PARIMPORA, SRINAGAR

S&F for factory made 30mm thick 1st class hard wood, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and as directed by Engineer-in-Charge. MAKE: M/S WOOD PRODUCT INDORE/M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI/ M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT/M/S PIONEER TIMBER PRODUCT CHANDIGARH/M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU/M/S M.S JOINERY WORKS, PARIMPORA, SRINAGAR

Preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge. MAKE: NEROLAC PAINTS/ JENSON & NICHOLSON/BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

S&F for floor door stopper 150mm long of alluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and as directed.

S&F for aluminium, anodised, barrel tower bolts of extruded section, 150 mm long, ISI marked complete all as specified and directed by Engr-in-Charge.

S&F for extruded aluminium alloy handles, fabricated type, anodised, 150mm, ISI marked complete all as specified and directed.

Mild steel sliding door bolts 250mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed ISI marked complete all as specified and directed by Engr-in-Charge

S&F for 125mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water remove dust, debries/rubbish etc, complete all as specified and as directed.

Material & Labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick walls or on concrete surfaces plastered surfaces finished even and smooth without using extra cement with WPC complete all as specified and as directed (WPC will be measured and paid separately).

Supply only integral water proofing admixture complete all as specified and directed. Make : Pidilite/Dr Fixit

S&F 15mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including taking up or down steel tubing and connections all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

S&F 20mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including taking up or down steel tubing and connections all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and acessories)

S&F 110mm PVC (SWR) pipes double socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed. MAKE: SUPREME/ASHIRWAD/FINOLEX/SFMC/ASTRAL

S&F 110mm PVC (SWR) bends any radius, complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore single socketed ,in any length with rubber ring joints,laid in trenches or in floors cement complete all as specified MAKE: SUPREME/ASHIRWAD/FINOLEX/SFMC/ASTRAL

S&F PVC (SWR) 110mm bore vent cowl complete all as specified

S&F PVC (SWR) 110mm bore junction single (Single T), complete all as specified

S&F PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement, 75mm dia oulet complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Preparation of old decorated plastered surfaces of walls incluidng complete removal of exisitng treatment and applying two coats of distempering with oil bound distemper white or any tinted on walls, filling gaps by putty after washing rubbing down and stopping of distermpered surfaces, over a coat of primer over and incluidng 2 mm thick layer of Birla white wall care putty complete all as specified and directed by Engr-in-charge. MAKE: NEROLAC PAINTS / JEHNSON & NICHOLSON / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS

Preparation of Old plastered surfaces of walls including complete removal of existing treatment and applying two coats of exterior emulsion paint of Make Apex (Asian) in any tint, over a coat of primer (as per manufacturer's instruction of Apex) over and including 2 mm thick coat of Birla white wall care putty, as on wall, roof projection, facias, chhajja, etc all as per manufacturer's instructions all as specified and directed by Engr-in-Charge. MAKE: BERGER (WEATHER COAT ALL GUARD)/ASIAN (APEX ULTIMA)/NEROLAC (EXCEL TOTAL)/JEHNSON & NICHOLSON / DULUX ICI

Preparation of new plastered surfaces of walls and applying two coats of exterior emulsion paint of Make Apex (Asian) in any tint, over a coat of primer (as per manufacturer's instruction of Apex), as on wall, roof projection, facias, chhajja, etc all as per manufacturer's instructions all as specified and directed by Engr-in-Charge. MAKE: BERGER (WEATHER COAT ALL GUARD) / ASIAN (APEX ULTIMA) / NEROLAC (EXCEL TOTAL) / JEHNSON & NICHOLSON / DULUX ICI

600 mm x 450 mm mirror of thickness 5/5.5mm of slected quality glass, mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete, fixed in repairs all as specified and as directed by Engr-in-Charge. MAKE: SAINT GOBAIN/MODI GUARD/TRIVENI FLOAT GLASS

PVC connections 15 mm size with PTMT nuts of length 600 mm, fixed in repairs, complete all as specified and diected by Engr-in-Charge. Make: Prayag/Polytuf/Supreme

S&F grating doom 150 mm with waste hole of PTMT. Make: Prayag/Polytuf/Supreme

S&F Harrison rails, anodised aluminium alloy, with fixing brackets, stops, rollers etc complete all as specified and directed by Engr-in-Charge.

S&F 0.63 mm thick corrugated Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 including dismantling plain or corrugated steel sheeting any guage thickness including nanital or similar pattern complete all as specified and directed. Make : SAIL/TATA/JSW STEEL

All as per Item No 50.00 but fixing only old sheets obtained from dismantling including dismantling plain or corrugated steel sheeting any guage thickness including nanital or similar pattern

M&L for two coats of synthetic enamel paint on new galvanised corrugated sheets incl preparation of new zinc or galvanised surface to receive paint camoflage pattern over a coat of red oxide primer after applying a treatment with modrant solution to remove the galvanisation of CGI sheet complete all as specified and directed. MAKE : BERGER PAINTS/ASIAN PAINTS/NEROLAC PAINTS/ GOODLASS

Preparation of old decorated surfaces of steel or iron works of any description exc 10 cm over width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-charge. MAKE: NEROLAC PAINTS / JEHNSON & NICHOLSON / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS

S&F in repairs wall hung basin with fixing accessories of size 610x480x195mm, Code No FNS-WHT-40801 with full pedestal of FNS-WHT-40801 of Make Jaquar, complete all as specified and as directed. Make : Jaquar Cat No FNS-WHT-40801 or equal approved in Kohler/Roca

S&F in repairs, Rimless single piece WC with UF soft close seat cover, hinges, fixing accessories set and cistern fitings of size 390x710x720, complete all as specified and as directed. Make : Cat No. VGS-WHT-81851SN of Jaquar or equal approved in Kohler/Roca

S&F single lever basin mixer with popup waste system with 450 mm long braided hose (fixed in repair), with accessories set , complete all as specified and as directed. Make : Cat No. FUS-CHR-29023B of Jaquar or equal approved in Kohler/Roca

S&F Toilet roll holder with flap, with accessories set (fixed in repair) , complete all as specified and as directed. Make : Cat No. ACN-CHR-1153S of Jaquar or equal approved in Kohler/Roca

S&F Soap dish holder with accessories set (fixed in repair), complete all as specified and as directed. Make : Cat No. ACN-CHR-1131N of Jaquar or equal approved in Kohler/Roca

S&F Angular stop cock with wall flange, with accessories set (fixed in repair), complete all as specified and as directed. Make : Cat No. FUS-CHR-29053 of Jaquar or equal approved in Kohler/Roca

S & F waste couplng 32mm size half thread with 80mm height with accessories (fixed in repair) set complete all as specified and as directed. Make : Cat No ALD-CHR-709 of Jaquar or equal approved in Kohler/Roca

S &F easy flex tube in chrome finish 1.5m long with nuts (fixed in repair) complete all as specified and as directed. Make : Cat No. SHA-CHR-571 of Jaquar or equal approved in Kohler/Roca

S &F hand shower 24 dia round shape single flow (ABS body chrome plated with gray face plate) with rubit cleaning system (fixed in repair) complete all as specified and as directed. Make : Cat No. HSH-CHR-5537N of Jaquar or equal approved in Kohler/Roca

S & F in replacement aquafree waterless urinal of size 31.5 x 33 x 60 cm complete all as specified and directed. Make : Hindware Cat No 60017 or equal approved in Kohler/Roca/Jaquar

Taking down carefully copper/Aluminium point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for re-use at site and making good disturbed surfaces of walls, floors etc as directed.

M&L for point wiring for one light point or fan point controlled by one switch with PVC insulated copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in existing sunk CI/pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth wire connected to earth folly and 3.0mm thick plastic laminated sheet cover all as specified and directed by Engr-in-Charge. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

All as per Item No 65.00 but for one 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 Sqmm size complete all as specified and as directed.

All as per Item No 65.00 but for one 3 pin socket outlet, 5 Amps Independent with cables 1.5 Sqmm size complete all as specified and as directed.

All as per ser Item No 65.00 but for point wiring with 2.5 sq mm PVC insulated, unsheathed single core stranded copper conductor 1100 Volt grade in PVC capping cassing on wall /floor etc with all accessories of suitable size MS/Pressed steel terminal boxes 1.6 mm thk with bakelite sheet cover (hylum) 3mm thick /PVC Gang box for mounting switch, socket, Cup washers complete with all accessories for one 3 pin 15 Amp socket outlet point on independent board including 1.5 sqmm PVC insulated copper conductor in green colour common earth and connecting to earth dolly all as specified.

S&F switch piano flush type one way single pole 5 Amp 240 volts. Make : Anchor/Legrand/Crabtree/Cona

S&F for socket outlet 2 in 1 3Pin, 5A, flush type complete all as specified and as directed. Make : Anchor/Legrand/Crabtree/Cona

S&F switch socket combination 2 in 1, 5 Amps flush type universal. Make : Anchor/Legrand/Crabtree/Cona

S&F switch socket combination 3/5 pin , 16 Amps flush type universal. Make : Anchor/Legrand/Crabtree/Cona

M&L for ceiling rose surface bakelite 65x50 mm two to three terminals.all as specified and directed by Engr-in-charge. Make : Anchor/Legrand/Crabtree/Cona

M&L for lamp holder PVC/Polycarbonate type insulated body with back plate suitable for batten fittings as specified and directed. Make : Anchor/Legrand/Crabtree/Cona

S&F in replacement of 9 watt LED bulb complete all as specified and directed. Make : Cat part No LHLDEUHEMC8R009 of Havells or equal approved in Crompton/Bajaj/Philips

Supply and Fixing Surface/wall mounted LED fittings with LED tube 20 watts capacity decorative ultra slim elegance LED lighting fixture with extruded Al. heat sink, environmental friendly, energy efficient type 4 feet long channel type bracket including neccessary conection prewired and making connection with 3 core copper flexible cable of appropriate size from ceilling rose/PVC connector to light fittings Make : Cat part No LHEXBLP7PN1W020 of Havells or equal approved in Crompton/Bajaj/Philips

Supply and Fixing Surface/wall mounted LED fittings with LED tube 9 watts capacity decorative ultra slim elegance LED lighting fixture with extruded Al. heat sink, environmental friendly, energy efficient type 2 feet long channel type bracket including neccessary conection prewired and making connection with 3 core copper flexible cable of appropriate size from ceilling rose/PVC connector to light fittings Make : Cat part No LHEXBLP7IN1W009 of Havells or equal approved in Crompton/Bajaj/Philips

S&F in replacement of Skylux LED 36watts recessed 2x2 luminaire to enhance the delight of occupants with comfortable experience through its design & glare free soft illumination and connection of 3 core copper wire with all accessories(Warm White) Make : Cat part No -BZRSQL 36 W GZi NW (Natural White) of Bajaj or equivalent in Havells/Philips.

Supply and fixing Recess mounted LED Wall 30Watts wall washers tilted 70 Degree outward and swivels 360 degree to offer best llumination on the wall and retail displays with module + driver complete all as specified and directed by Engr-in-Charge. Make : Cat part No SPARKLEPROSNOOTDLR30W840MOD38DWHTNEEM of Havells or equal approved in Crompton/Bajaj/Philips

Supply and fixing of LED 15Watts recessed mounted panel in a light weight plastic body fittings complete all as specified and directed by Engr-in-Charge. Make : Cat part No LHEBLDP5IN1W015 of Havells or equal approved in Crompton/Bajaj/Philips

Supply and fixing of LED Step light 4Watts in white powder coated cast aluminium body & IP 54 protection. Make : Cat part No BLSGV 4WLEDWH of Bajaj or equal approved in Crompton/Havells/Philips

S&F in repairs Exhaust Fan Non metalic range 250mm sweep Plastic Type, complete all as specified and directed by Engr-in-Charge. Make : Cat part No : Ventil Air DX of Havells or equal approved in Bajaj/Khaitan/Usha Luxar/CG Note : Old exhaust fan obtained from the site shall be depoisted in MES store yard.

Supply and fixing MCB distribution board Double door, regal grey, sheet metal enclosure, TPN 415 volts 4 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc incl taking down old DBs. Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCCB 4 pole 160 Amps, 16 KA, 415 Volt complete incl taking down of old MCCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4200 17 of Legrand (DPX³) or equal approved in Schneider (NSX)/Siemens (3VL2)/L&T (D-Shine)

Supply and fixing MCCB 4 pole 100 Amps, 16 KA, 415 Volt complete incl taking down of old MCCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4200 15 of Legrand (DPX³) or equal approved in Schneider (NSX)/Siemens (3VL2)/L&T (D-Shine)

Supply and fixing MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts 12 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc incl taking down old DBs. Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts 8 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc incl taking down old DBs. Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCB SPN 63 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 20 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Supply and fixing MCB SPN 40 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 18 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Supply and fixing MCB SP 6 to 32 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 87 to 4085 95 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Supply and fixing MCB SP 40 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 96 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Supply and fixing MCB SP 63 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 98 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Sub main wiring with two runs of 10 Sqmm (2x10 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 6 Sqmm (1x6sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 10 Sqmm (2x10 sqmm), one run of 6Sqmm (1x6 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

Sub main wiring with two runs of 6 Sqmm (2x6 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 2.5Sqmm (1x2.5sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 6 Sqmm (2x6 sqmm), one run of 2.5Sqmm (1x2.5 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

Sub main wiring with two runs of 1.5 Sqmm (2x1.5 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 1Sqmm (1x1 sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 1.5 Sqmm (2x1.5 sqmm), one run of 1Sqmm (1x1 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

Material and labour for earthing complete with galvanised steel earth plate 600 x 600 x 6 mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI wire of size 4 mm dia by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No.3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore light grade GI watering pipe, lugs, 15mm bore light grade GI protection pipe, test point etc including taking down old earthing material complete all as specified and as directed. Note: (i) Item includes the cost of 7.5 m GI pipe for protection of earth lead. Any additional length shall be adjusted through deviation order. (ii) Item includes the cost of 7.5 m GI earth lead. Any additional in length shall be adjusted through deviation order (iii) Item includes the cost of Charcoal and commercial salt

M/S Praveen Kumar and Sons

Rampal Singh Contractor

SATISH KUMAR AND SONS