Renovation and Modification of Central Library in Academic Area at IIT

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:

All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m.

All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:

1:3:6 (1 Cement: 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement: 3 coarse sand), cost of required centering, shuttering complete:

1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Shelves (Cast in situ)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.

Granite stone slab of colour black, Cherry/Ruby red

Area of slab over 0.50 sqm

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin-based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately).

12mm thick commercial ply conforming to IS: 1328 BWR type

Providing and fixing fire-resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet (Zinc coating not less than 120gm/ sqm) suitable for mounting 120 minutes Fire Rated Glazed Door Shutters. The frame shall be filled with mineral wool Insulation having density minimum 96Kg/cum. The frame will have a provision of G.I. anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with factory made template for SS ball bearing hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- Charge. (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minutes fire rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-Charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/sqm) duly filled mineral wool insulation having density minimum 96 kg/cum and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-Charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer- in- charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails, screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing stainless steel soft closing spring hinges at 0- degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge.

Providing and fixing 2mm thick 16 to 19mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

Using M.S. angels 40x40x6 mm for diagonal braces

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in- charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge.

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:6 (1 cement: 6 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Water thinnable cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade:

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

French spirit polishing :

Two or more coats on new works including a coat of wood filler

Providing and applying white cement-based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Polishing in high gloss/matt finish melamine clear polish on woodwork in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/ 120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

With cement mortar 1:4 (1cement: 4 coarse sand)

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge.

For door/ window/ clerestory window

Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre) (if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account)

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer- in-Charge.(a) Internal Work- Exposed on wall

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge.

In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Of area beyond 3 sq. metres

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Demolishing mud phaska in terracing and disposal of material within 50 metres lead.

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material within 50 meters lead as directed by Engineer-in-charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink asper IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making goodthe walls wherever required :

Kitchen sink without drain board

610x510 mm bowl depth 200 mm

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto1 metre long with S.S. triangular plate to Eureopean type W.C. ofquality and make as approved by Engineer - in - charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing toilet paper holder:

C.P. brass

Providing and fixing soil, waste and vent pipes :

100 mm dia

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outsideIS:15905

Providing and fixing M.S. holder-bat clamps of approved design toSand Cast iron/cast iron (spun) pipe embedded in and includingcement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size),including cost of cutting holes and making good the walls etc. :

For 100 mm dia pipe

Providing and fixing bend of required degree with access door, insertionrubber washer 3 mm thick, bolts and nuts complete.

100 mm dia

Hubless centrifugally cast (spun) ironepoxy coated inside & outside as perIS:15905

Providing and fixing plain bend of required degree.

100 mm dia

Hubless centrifugally cast (spun) ironpipes epoxy coated inside & outsideIS:15905

Providing and fixing double equal plain junction of required degree.

100x100x100x100 mm

Hubless centrifugally cast (spun) ironpipes epoxy coated inside & outsideIS:15905

Providing and fixing single equal plain junction of required degree :

Hubless centrifugally cast (spun) ironepoxy coated inside & outside as perIS:15905

Providing and fixing Hubless centrifugally cast iron offsets epoxycoated inside & outside as per IS:15905

65 mm offsets

With 100 mm dia pipe

Providing and fixing Hubless centrifugally cast iron offsets epoxycoated inside & outside as per IS:15905

130 mm offsets

With 100 mm dia

Providing and fixing terminal guard :

Hubless centrifugally cast (spun) ironepoxy coated inside & outside as perIS:15905

Providing and fixing shielded coupling for Hubless centrifugally castiron pipe

100 mm dia

SS 304 grade coupling with EPDM rubbergasket

Providing and fixing trap of self cleansing design with screwed downor hinged grating with or without vent arm complete, including cost ofcutting and making good the walls and floors :

100 mm inlet and 100 mm outlet

Hubless centrifugally cast (spun) ironepoxy coated inside & outside as perIS:15905

Cutting chases in brick masonry walls for following diameter sandcast iron/centrifugally cast (spun) iron pipes and making good thesame with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6graded stone aggregate 12.5 mm nominal size), including necessaryplaster and pointing in cement mortar 1:4 (1 cement : 4 coarsesand) :

100 mm dia

Providing and fixing white vitreous china extended wall mountingwater closet of size 780x370x690 mm of approved shape includingproviding & fixing white vitreous china cistern with dual flush fitting,of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres),including seat cover, and cistern fittings, nuts, bolts and gasket etccomplete.

Providing and fixing white vitreous china battery based infrared sensoroperated urinal of approx. size 610 x 390 x 370 mm having pre &post flushing with water (250 ml & 500 ml consumption), havingwater inlet from back side, including fixing to wall with suitablebrackets all as per manufacturers specification and direction ofEngineer-in-charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall

25 mm dia nominal bore

32 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :

15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

20 mm nominal bore

32 mm nominal bore.

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :

150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

150 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

150 x 100 mm size P type

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer- in-charge

Powder coated minimum thickness 50 micron aluminium

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540- F & ISO 11600

Upto 5 mm depth and 5 mm width

Upto 10 mm depth and 10 mm width

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer- in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer- in- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.

Cleaning the sand stone surface and removing dirt, dust, bird dropping, grease, oil, algae, fungus, monkey beats, vegetable growth etc., including providing, applying and washing the surface with liquid Ammonia Chemical of 5% solution and other chemical cleaning agent as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacturer, with the help of required scrubbers and also cleaning with machine operated water jet mixed with desired quantity of fine silica where ever required, without causing any scratching/ damage to the stone surface and finally washing the surface with clean water with the help of pressure jet machine, complete in all respect, including taking all precautions to safeguard ventilators, windows, doors etc. by suitable covering so as to avoid any damage to the building/structure, all as per direction of Engineer- in-charge (The rate is inclusive of all materials & labours involved except scaffolding).

Providing & fixing in position Phenol bonded Bamboowood flooring with planks of sizes 14mm thick, minimum 1800mm length and minimum 100 mm wide, in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The flooring shall be fixed with tongue and groove interlocking system, with underlayment of 4mm thick expanded polyethylene foam sheets having density 40kg/cum, over prepared surface with necessary quarter round planks of size 1900mm x 18mm and door reducer of size 1900mm x 44mm, wherever required. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer-in-charge.

Providing & fixing in position Phenol bonded Bamboo wood in wall skirting with planks of sizes 14mm thick, 1900mm length (minimum) and 85mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The skirting shall be fixed with SS screws & rawl plugs, over underlayment of 4mm thick, expanded polyethylene foam sheets having 40kg/cum density over prepared surface. The bamboowood planks shall have minimum density of 1000Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.

With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge

50mm average thickness

25 mm average thickness

Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.

Bars upto 12 mm diameter

Bars above 12 mm diameter

Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.

Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/ masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-Charge. (The payment shall be made on the basis of actual weight of approved grout injected.)

Epoxy injection grout in concrete/RCC work of approved make

Providing, laying & jointing of foam concrete blocks having density @ 500kg/cum (autoclaved aerated cement blocks) in cement mortar 1:4 (1 cement : 4 coarse sand) over the existing floor at all level, lead as per direction of Engineer-In-Charge.

Providing and fixing 5mm thick looking mirror of superior galss and of approved quality and make: Saint Gobain / Modi Guard and of required shape and size with necessary wooden moulded beading (2nd class teak wood) of size 50x12mm duly polished with backing of 12mm thick commercial ply including priming coat on unexposed surface, with necessary fixing arrangement and screws etc. complete :

Driling and fixing NRV nozzles in RC members, including (fixing material : Renderoc Plug of Fosroc / Sikadur-31 of Sika / MasterBrace 2200 of BASF or equivalent of Pidilite & Krishna Conchem). i. Drilling Holes: Drilling 12 mm dia, 50 to 75 mm deep holes or upto required depth in structural members of the intervals of 350 mm in staggered manner or as directed by the Engineer-in-charge in RC structural elements. ii. Cleaning of holes: Clean the holes by air blower prior to fixing nozzles. iii. Fixing of Nozzles: Insert 12mm dia. NRV nozzles in cleaned holes. External end of nozzles to be machine to receive outlet of grouting gun. Fix it inside the holes by applying thyrotrophic epoxy putty to ensure complete sealing. Cure the system for min. 12 hrs. iv. Cuttting of Nozzles: Cut the nozzles by chisel after completion of grouting without damaging structural elements:

Providing mixing & applying pre-batched one component polymer modified dual shrinkage compensated thixotropic cementious patch repair mortar as per the manufacturer specifications and as per the direction the Engineer-in-charge. The comperessive strength of polymer modified mortar shall be ≥ 45 Mpa (28 Days) according to ASTM C109. ( Product :- Renderock S2 of Fosroc/ SikaTop® 122 HS of Sika / MasterEmaco S 348 of BASF or equivalent of Pidilite)

For 20 mm thickness over slab, beams, columns and stair case slabs.

Add/ deduct for every 10 mm thickness

Providing and fixing 2.0mm thick heavy duty homogeneous floor covering with polyurethane reinforcement in flooring & skirting in approved pattern on a smooth and damp-proof base using rubber based adhesive of approved quality and manufactured like Fevicol SR 998 or equivalent including rolling with light wooden roller weiging about 5 kg. all complete as directed by Engineer - in - Charge, in approved colour and shade having follwoing specifications: 1. Full conformance with the requirements of ISO 10581/EN 649. 2. Flexible pvc sheet and tile flooring in 2mm thickness. 3. Use area classification 23/34/43 as defined in ISO 10874/EN 685. 4. Fully tested to EN 13501-1 in respect of flamespread 5. For slip resistance, classified DS to EN 13893. 6. Classified Type I within ISO 10581 re Binder Content. 7. BRE Global A+ rating ENP 472* in major use areas such as education and healthcare. 8. Tested to international standards for low VOC emissions.

Providing and fixing 12 mm thick frameless toughened glass in partition and doors of approved brand and manufacture, including making necessary holes etc. for fixing the fittings but excluding the cost of fittings all complete as per direction of Engineer-in-charge.

Providing and fixing H or D type handle as per drawing and directions of Engineer-In-Charge of Ozone make (MODEL-OGH- 55 or OGH-11) /Dorma / Hettich of size 32 mm dia. and 457 mm long with necessary screws etc. complete.

Providing and fixing wall to Glass connector or glass to glass connector of appropriate degree of make Ozone / Dorma / Hettich Complete as per drawing and Direction of Engineer-in-charge.

Providing and fixing Over Panel Fitting of Ozone make (MODEL- OPF-1) /Dorma / Hettich Complete as per Direction of Engineer- in-charge.

Providing and fixing top Pivot of Ozone make (MODEL-OFS- ACC-GDP) or Equivalent of Dorma / Hettich Complete as per Direction of Engineer-in-charge.

Providing and fixing Floor spring of Ozone make (MODEL FS- 9000) or Equivalent of Dorma / Hettich Complete as per Direction of Engineer-in-charge.

Providing and fixing U shape Chanel of make ozone (Model: OZGL-UPR-SS) or equivalent of Dorma / Hettic & wall Angle in top and bottom for supporting the Toughened Glass as per direction of Engineering-charge

Providing and fixing self-adhesive frosted/decorative/sun control film on glass partition, glass door and windows of approved design and make 3M / Garware or equivalent all complete as per direction of Engineer-in-charge.

Removing and taking out old PVC flooring / PVC tiles i/c stacking of unserviceable material within 50 meters lead as per directions of Engineer-In-Charge.

Providing & fixing chrome plated brass deck mounted battery based infrared sensor operated pillar cock, having foam flow technology of make cera / Hindware or equivalent (Cat No.: F6010108) including the cost of making holes in granite and slab and as per directions of Engineer-In-Charge.

Providing and Fixing Toilet Cubicle (Make: Merino / Greenlam) of standard / dimensions as per site requirement made up of 12mm thick Solid Compact Laminate Panels. Finish of the Compact Laminate panels should be as suede / Raw Silk or as approved by the Engineer-In-Charge. The complete system includes doors, pilasters and intermediate panels finished with approved texture / shade as per the detail drawings & as per IS 2046 and as per fire retardant BS-476/97 standard. The product should have Green Guard Certificate. This also includes providing and fixing in position necessary hardware made out of SS 304 & aluminium powder coated top rail as per manufacturer's specifications. The main hardware include SS Door Knob, SS Gravity Hinges, SS thumb turn lock set indicators, Aluminium powder coated top rail, SS Coat Hooks, SS U- Channels, SS Adjustable foot, Noise deafening tape, SS Screws and wall plugs etc. The top fitting should consist of Aluminium Powder Coated Top Rail which will get fixed with mid & End pilasters. The minimum dimensions of toilet cubical are as follows: 1. Width of cubical = 1000mm for general & 1500mm for Divyang 2. Depth of cubical = 1500mm for general & 1750mm for Divyang 3. Height of entire cubical = 1995mm 4. Width of Door = 600mm for general & 900mm for Divyang. 5. Height of Door = 1785mm 6. Ground Clearance = 100 to 150mm (as specified by the manufacturer)

Providing and fixing fire rated hydraulic door closer of BLC-0604 Backer Fire Solution / TS 89 F Dorma / Geze TS 2000 V with necessary accessories and S.S. screws etc. complete as per directions of Engineer-In-Charge.

Providing and fixing Push type Single Point panic bar for Single Leaf door with external trim & Half Cylinder For Glazed Fire Check Door at stair case location of make Backer Fire Solution / Dorma / Geze with necessary accessories and S.S. screws etc. complete.

Providing and fixing 300 fire rated mm long Flush Bolt one at top and one at bottom on Glazed Fire Check Door of make Backer Fire Solution / Dorma / Geze with necessary accessories and S.S. screws etc. complete as per directions of Engineer-In-Charge.

Supply and installation of required size, shape, design and colour (as per enclosed drawing) Chair as per approved make and direction of Engineer- in-charge (Make: Godrej, Model no. Motion High Back Larger Seat with adjustable Armrests Chair (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour WORKSTATION of Size 1500W x 600D x 1200H (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make: Godrej, Model No.-RECTA WORKSTATION [WISH] + KBPT + PEDASTAL & CPU TROLLEY / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour WORKSTATION of Size 900W x 600D x 1200H (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make: Godrej, Model No.-RECTA WORKSTATION [WISH] + KBPT + PEDASTAL & CPU TROLLEY / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour WORKSTATION of Size 1650W x 600D x 1200H (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make: Godrej, Model No.-RECTA WORKSTATION [WISH] + KBPT + PEDASTAL & CPU TROLLEY /(Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour WORKSTATION (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make: Godrej, Model No.- RECTA WORKSTATION [WISH] + KBPT + PEDASTAL & CPU TROLLEY / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour WORKSTATION of Size 1500W x 750D x 750H (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make: Godrej, Model No.-RECTA WORKSTATION [UPBEAT] + KBPT + PEDASTAL & CPU TROLLEY / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour SQUARE TABLE of size 1150x1150x740mm (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make-Godrej, Model No.- MINGLE POD SQUARE TABLE of size 1150x1150x740mm / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour RECTANGULAR TABLE of size 2100x1150x740mm (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- MINGLE UNITIZED PLT TABLE of size 2100x1150x740mm / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour DOUBLE SIDED UNIT of size 1200W X 600D X 2078H (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- DOUBLE SIDED UNIT of size 1200W X 600D X 2078H, RDNC DR1 MTL SW 1200mm 600mm / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour WALL SIDED UNIT of size 1200W X 300D X 2078H (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- WALL SIDED UNIT of size 1200W X 300D X 2078H, RDNC SR1 MTL SW 1200mm 300mm / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour 1 SEATER SOFA of size Width (W): 86.0 CM, Depth (D): 90.5 CM, Height (H): 85.5 CM, Seat Height (SH): 45.0 CM. (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make-Godrej, Model No.- PISA 1 SEATER SOFA / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour 2-SEATER SOFA of size Width (W): 146.0 CM, Depth (D): 90.5 CM, Height (H): 85.5 CM, Seat Height (SH): 45.0 CM. (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- PISA 2-SEATER SOFA / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour 3-SEATER SOFA of size Width (W): 206.0 CM, Depth (D): 90.5 CM, Height (H): 85.5 CM, Seat Height (SH): 45.0 CM. (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- PISA 3-SEATER SOFA / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour SIDE / CORNER TABLE of size 600x600 mm with tinted toughened glass top (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- PISA SIDE / CORNER TABLE / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour PERSONAL LOCKER UNIT 38x183x45 cm (WxHxD) (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- PERSONAL LOCKER UNIT, Product ID: PLU00001DX / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour FILING CABINET of size 1072x1200x460 mm (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make-Godrej, Model No.- Reserve Lateral Filing Cabinet, Product ID: RESERV01DX / equivalent of Featherlite / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour CHAIR of size 43.5x87.5x56.5 CM (WxHxD) having Leatherette as upholstery material (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- VIVID CHAIR/ (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour VISITOR CHAIR WITHOUT ARM REST of size 48.5 x 93.3 x 58.9 CM (WxHxD) (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- MOTION VISITOR CHAIR WITHOUT ARM REST / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour DOUBLE DOOR STEEL ALMIRAH of size 91.6 x 198 x 48.6 CM (WxHxD) (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- STORWEL PLAIN / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour SOFA of size 90 x 79 x 70.5 CM (WxHxD) (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make-Godrej, Model No.- GRAPH SOFA / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour BACK-TO-BACK SOFA of size 90 x 79 x 133.5 CM (WxHxD) (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- GRAPH BACK- TO-BACK SOFA / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour WORKPOD of size 122.5 x 132.8 x 93.5 CM (WxHxD) (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- IMMERSE WORKPOD/ (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour FLIP CHAIR of size 60 x 74 x 40 CM (WxHxD) (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make-Godrej, Model No.- TETRIS FLIP CHAIR / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour ROUND TABLE of size 90 (dia) x 102 (H) CM (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make-Godrej, Model No.- TOPO ROUND TABLE / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour RECTANGULAR TABLE of size 90 x 120 x 72 CM (WxDxH) CM (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- TOPO RECTA TABLE / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour DESK of size 60 x 45 x 72 CM (WxDxH) CM (as per enclosed drawing) as per approved make and direction of Engineer- in- charge. (Make-Godrej, Model No.- MODESK / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour CHAIR of size 63.50 x 63 x 80 CM (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make- Godrej, Model No.- GREET CHAIR / (Equivalent of Featherlite/ equivalent of wipro)

Supply and installation of required size, shape, design and colour RECTANGULAR TABLE of size 1800x900x740mm (as per enclosed drawing) as per approved make and direction of Engineer- in-charge. (Make-Godrej, Model No.- INSIGHT TABLE of size 1800x900x740mm / (Equivalent of Featherlite/ equivalent of wipro).

ELECTRICAL WORK

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc .as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed steel conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

3 x 2.5 sq. mm

6 x 2.5 sq. mm

3 x 4 sq. mm

6 x 4 sq. mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Telephone socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

6 Module (200mmX75mm)

12 Module (200mmX150nnm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

1 run of cable

2 run of cable

3 run of cable

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

125 A, 16 KA,TPMCCB

150 A, 16 KA,TPMCCB

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way , Double door

16 way, Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MOB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MOB TPDB is normally used where 3 phase outlets are required.)

8 way (4 + 24), Double door

12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MOB DB complete with connections, testing and commissioning etc. as required.

Single pole

Triple pole

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top along with 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required.

For 14 way, Double door SPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required.

Supplying, installing, testing and commissioning of following capacity End Feed Unit made of 1.6mm thick sheet steel enclosure duly painted with powder coating to existing rising mains complete with TPN disconnect or FSU and HRC fuses, mounting stands, cable end box, brass compression gland, connections, earthing etc. as required.

Supplying, installing on wall, testing and commissioning of following capacity Air Insulated Compact Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with enclosure having IP-54 rating after fixing the tap of boxes and all accessories, made of 1.6mnn thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 Al sq cm at nominal current rating, necessary joints & expansion joints, fire barrier at each floor, provision of tapping at every metre, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required.

630 A, lsc = 50kA for 1 second

Supplying, installation, testing & commissioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required

250 A, lsc= 30kA for 1 sec

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thickness

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia GI. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ subnnain wiring/ cable as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3.5 X 95 sq. mm (45mm)

3.5 X 150 sq. mm (50mm)

3.5 X 240 sq. mm (62mm)

4 X 16 sq. mm (28mm)

Supplying and fixing of 32 mm dia X 2.00 metres long GI. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.

FIRE DETECTION AND ALARM SYSTEM

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of 6 inches dia, 2 watts, 70/100 volts ceiling speaker complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rnns operating at 240 Volt AC Supply complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

speaker cable Single pair, 2-core, 1.5 sqmm

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLOC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and fixing following rating, double pole, 240 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and fixing FR PVC DLP adaptable trunking without cover of (150 mm x 50 mm) size with provision of internal partition separation for Power & LAN on surface on existing wall etc. as required. .

Providig and Fixing of FR PVC trunking cover width 40 mm + full cover width 85 mm for Power + LAN component

Providing and fixing of Clip on partition - Plastic .

Providing and fixing of Seperation on partition - Plastic .

Providing and fixing of End caps for 150 mm x 50 mm trunking .

Providing and fixing of Internal angle for 150 mm x 50 mm trunking .

Providing and fixing of External angle for 150 mm x 50 mm trunking .

Supplying and Fixing DLP U-PVC turnking of 105mm x 50mm on surface etc as required.

Supplying and Fixing Full Flexible cover of width 85mm on existing DLP U-PVC turnking etc as required.

Supplying and Fixing of internal angle for 105mm x 50mm existing DLP U-PVC turnking etc as required.

Supplying and Fixing of external angle for 105mm x 50mm existing DLP U-PVC turnking etc as required.

Providing and fixing of 90° Flat angle for 105 mm x 50 mm trunking .

Supplying and Fixing of End cap for 105mm x 50mm on existing DLP U-PVC turnking etc as required.

Supplying and Fixing 1 module arteor frame for 40 mm cover .

Supplying and fixing of 3 module arteor frame for 85 mm cover .

Supplying and fixing of 6 module arteor frame for 85 mm cover .

Supplying and fixing following modular switch/ socket on the existing 1/3/6 module frame / U-PVC trunking system including connections etc. as required.

Information socket - category 6-UTP - 1 module .

6 Amp switch

20 Amp switch

6 Amp switch-2/3 pin universal socket outlet

6 pin 20 Amp socket outlet/6 pin 6/16 A universal socket

Supplying and fixing of 8 (2 x 4) modules Pop-up flush-mounting box . including cutting the table top etc as required.

Supplying and fixing double USB charger-2 module.

Supplying and fixing HDMI socket-1 module.

Supplying and Fixing Metal/GI raceway of size 225 mm x 38 mm- 3 compartments including cutting the floor and repairing the same as required. (Length 2.44 m)

Supplying and Fixing Metal/GI raceway junction box (225mm x 225mm x 65-90mm) for joining raceway of size 225 mm x 25 mm (metal) on the floor including cutting the floor etc as required.

Supplying, Installation, Testing and Commissioning of Cable cubby (One no 05 Amp switch & socket, 1 No 3000mA USB port & 1 No. Data Socket(RJ-45)) on existing table top including drilling hole, fixing cable cubby & finishing etc as required.

Supplying and fixing 1" x 1" pre coated aluminium casing and capping on existing table etc as required.

Supply of 25W Surface/suspended linear 4ft luminaire(50mm width) made of Aluminum extruded housing in white powder coated finish and snap fit plastic moulded end caps, High transmittance PMMA opal profiled diffuser, control gear accessible and serviceable from bottom, suitable for standalone and continuous row mounting for endless line of light, High efficiency long life LED package in integral module with lumen efficacy > 95 Lm/W and viewing angle of 120° to ensure better uniformity. Powered by an integral isolated low THD electronic LED driver ( SMPS based constant current supply) with output short circuit protection, surge protection. Lumen Output of 2400 lumens.CRI >80, Color temperature 4000K, THD <10% and PF >0.90,IP20,IK03.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3.5 KV.

Supply Installation and Commissioning of surface/ Suspended 15W round shape cylinracal light with high performance LEDs, pressure die-cast aluminium heat sink & PC diffuser in white powder coated finish with integral electronic low THD (<15%) LED driver.High efficiency long life LED package in integral module with lumen efficacy of >100 lm/W , with deep recessed, glare free. Powered by an integrated driver, SELV Output electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test. Lumen Output of 1500 lumens, CRI >80, Color temperature 3000/4000K, THD <10% and PF >0.95,IP40,IK03.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV;

Supply and installation of LED 40W decorative, corrosion resistant, surface luminaire. Housing in Aluminum extrusion heat sink for effective thermal management, sturdiness and excellent corrosion resistant Lumen Output of 4200 lumens.CRI >80, Color temperature 6000K and PF >0.90,IP20,IK03.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV;

Supply Installation and Commissioning of recess 15W round shape light with high performance LEDs, pressure die-cast aluminium heat sink & PC diffuser in white powder coated finish with integral electronic low THD (<15%) LED driver. High efficiency long life LED package in integral module with lumen efficacy of >100 lm/W , with deep recessed, glare free. Powered by an integrated driver, SELV Output electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test. Lumen Output of 1500 lumens, CRI >80, Color temperature 3000/4000K and PF >0.95,IP40,IK03.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV;

Supply and installation of LED 25W decorative, corrosion resistant, surface-suspended luminaire. Housing in Aluminum extrusion heat sink for effective thermal management, sturdiness and excellent corrosion resistant fitted in white finish.High transmittance PS diffuser in opal finish for glare free uniform light distribution.High efficiency long life SMD LED module is mounted on FR4 with lumen efficacy of >140lm/W to enhance the lumen output.Powered by an integral isolated low THD electronic LED driver ( SMPS based constant current supply) with output short circuit protection, surge protection. Lumen Output of 2180 lumens.CRI >80, Color temperature 4000K, THD <10% and PF >0.90,IP20,IK03.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV;Havels

Supply installation and Commissioning of Round donut shape suspended LED light,25W decorative, corrosion resistant, surface- suspended luminaire. Housing in Aluminum extrusion heat sink for effective thermal management, sturdiness and excellent corrosion resistant fitted in white finish.High transmittance PS diffuser in opal finish for glare free uniform light distribution.High efficiency long life SMD LED module is mounted on FR4 with lumen efficacy of >140lm/W to enhance the lumen output.Powered by an integral isolated low THD electronic LED driver ( SMPS based constant current supply) with output short circuit protection, surge protection. Lumen Output of 2180 lumens.CRI >80, Color temperature 4000K, THD <10% and PF >0.90,IP20,IK03.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV;

Supply and installation of Hexagone shape 25W LED decorative, corrosion resistant, surface-suspended luminaire. Housing in Aluminum extrusion heat sink for effective thermal management, sturdiness and excellent corrosion resistant fitted in white finish.High transmittance PS diffuser in opal finish for glare free uniform light distribution.High efficiency long life SMD LED module is mounted on FR4 with lumen efficacy of >140lm/W to enhance the lumen output.Powered by an integral isolated low THD electronic LED driver ( SMPS based constant current supply) with output short circuit protection, surge protection. Lumen Output of 2180 lumens.CRI >80, Color temperature 4000K, THD <10% and PF >0.90,IP20,IK03.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV;Havels

Supply of 2x2 Panel recess mounting luminaire with suitable wattge as per design high performance LEDs, suitable for mounting with Armstrong/Grid ceiling.CRCA powder coated white after phosphochromate treatment. LED module is mounted on FR4 with lumen efficacy of >140lm/W to enhance the lumen output and viewing angle of 120° to ensure better uniformity.Powered by an independent Isolated, electronic LED driver with Output Short- circuit protection, Surge protection & other reliability test. Lumen Output of 3800 lumens.CRI >80, Color temperature 4000K, THD <10% and PF >0.95,IP20,IK03.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV.

S/I/T/C of Microwave Surface Mount Sensor (occupancy Sensor) etc as required.

Supplying, Installation, testing & commissioning of energy efficient LED compound light equipped with power coated PDC alluminium body & secondry optical lens for superior light distribution with energy efficient electronic driver with following features:- 130-300 Vac, 50Hz, wattage 120 Watts, efficancy not less then 110 Lm/W, CCT 6500K, Nominal surge protection 2.5 kV, Power factor not less then 0.9, Minimum IP protection 66 etc. in suitable size GI pipe with reducer, GI saddle, bracket for proper fixing as required.)

S/I/T/C of high speed wall mounting fan 400 mm sweep, copper winding, capacitor start, suitable for operation on 230V, 50 Hz, AC supply with inbuilt speed regulator etc. complete with all standard accessories such as motor, blades clamp etc as required. Colour of fan shall be finallized by Engineer-in-charge)

S/I/T/C of 12"(300mm) size,1400rpm,copper wound, heavy duty metalic Exhaust Fan of double ball bearing capacitor start,suitable for 230 volt,50 Hz,single phase A.C. supply and complete with accessories such as motor, legs,frame,loober and Nut & bolts etc complete as required.

S/I/T/C of 10"(250mm) size,copper wound, ventiling fresh air fan of double ball bearing capacitor start,suitable for 230 volt,50 Hz,single phase A.C. supply and complete with accessories such as motor, legs,frame,loober and Nut & bolts etc complete as required

Providing and fixing 160A,36kA,FP MCCB rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders with SS Enclosure box suitable for 415 volt,3 phase,4 wire,50 Hz A.C supply system including drilling holes in SS enclosure box, making cable connections, etc. as required. Note: SS Enclosure is include in this item)

Supplying and drawing of UTP 4 pair CAT 6A LAN Cable in the existing surface/ recessed steel/ PVC conduit as required

1 run of Cable

Supplying & Laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium armoured power cable of 1.1 kV grade of following size on wall surface as required.

Above 35 sq. mm and upto 95 sq. mm (3.5C x 95 sq.mm) (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (3.5C x 150 sq.mm) (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) (3.5C x 300 sq.mm)

Upto 35 sq. mm (2C x 1.5 sq.mm) copper cable (clamped with 1mm thick saddle)

Supplying,Laying and fixing of one number PVC insulated and PVC sheathed / XLPE Aluminium and copper armoured power cable of 1.1 KV grade of following size on cable tray as required.

Above 35 sq. mm and upto 95 sq. mm (3.5C x 95 sq.mm) (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (3.5C x 150 sq.mm) (clamped with 25/40x3mm MS flat clamp)

Upto 35 sq. mm (4C x 16 sq.mm) copper cable (clamped with 1mm thick saddle)

FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning of intelligent addressable High Sensitivity Photo Detector with sensitivity level of 0.02% to 2% Obs/Feet. The detector shall have the parabolic amplifier to focus the light beam to a very small volume near the receiving photo sensor at the incipient stage of fire- when the smoke particles are lesser than 0.3 microns intrudes inside the detection chamber & shall have better response time at much earlier stage of fire. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches.

"Supplying, installing, testing and commissioning approved make microprocessor based Multi-loop, Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 trouble events including 1000 alarm log history events, Self Programmable alphanumeric keypad for programming. The panel should be equipped with sufficient number of loops & each loop shall have a capacity of inimum 125 detectors & 125 other devices excluding 20% spare. The panel shall work in degrade mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition with the charging capacity of 200AH. The panel shall be capable of self programing without any dependancy on dongle or programming software. Quoted rate shall include supply of necessary software & hardware for programming the panel with all necessary licence. Panel shall have Modbus/ Bacnet over IP protocol for future integration with BMS. However, for present arrangement FA system will be standalone with 24x7 monitoring. The panel shall be capable for remote accessibility on a mobile app through cloud platform/solution. Complied to meet UL864, 10th Edition and FM Approved. The Panel will be Seamlessly Integrated with existing Central Fire Alarm Panel and complete information of Panel should be seen on Main Central Fire Alarm Panel" 4 Loop Panel

DOME CAMERA - SITC of 2Mpx IR Varifocal Dome Camera 1920 X 1080 at 25/30fps,1/2.9"CMOS, lens 3.5-9mm,Auto focus and zoom, H.265, H.264 compression, Smart Compression, internal 850nm IR Range 30 meter from same OEM, 100dB true WDR as per IEC62676 , Built in Microphone, triple streaming, Motion Detection, Camera sabotage,IP66,IK10 housing, Camera shall support SD card 2TB,ONVIF profile S,G, & T,HTTPS using TLS 1.2, AES256, NDAA, Temp +60deg, UL/cUL Listed, UL/IEC/EN 62368-1, UL 60950-22, CE, FCC. The Camera to be provided by OEM should not be complying to GB28181, GB/T28181-2011 standards and there should be no option to activate or deactivate GB/T 28181 standards in the camera web page/Settings. Note: MAF/Letter of Authorization from Original Equipment Manufacturer (OEM) on the same and specific to the tender should be submitted before delivery of the Material.

"BULLET CAMERA - SITC of 2Mpx IR Varifocal Bullet Camera, 1920 X 1080 at 25/30fps,1/2.9""CMOS, lens 3.5-9mm,Auto focus and zoom, H.265, H.264 compression,Smart Compression, internal 850nm IR Range 30 meter from same OEM, 100dB true WDR as per IEC62676, triple streaming,Motion Detection,Camera sabotage,IP66,IK10 housing,Camera shall support SD card 2TB,ONVIF profile S,G, & T,HTTPS using TLS 1.2, AES256, NDAA,Temp +60deg, UL/cUL Listed, UL/IEC/EN 62368-1, UL 60950-22, CE, FCC.The Camera to be provided by OEM should not be complying to GB28181, GB/T28181-2011 standards and there should be no option to activate or deactivate GB/T 28181 standards in the camera web page/Settings. Note: MAF/Letter of Authorization from Original Equipment Manufacturer (OEM) on the same and specific to the tender should be submitted before delivery of the Material."

VMS SOFTWARE - Supply installation Testing and Commissioning of Video Management Software, All Cameras shall be of same make*web based client allows viewing and exporting video without installing any software.*Imports users and roles from existing LDAP servers to reduce administrative overhead,and enables single sign-on (SSO)*Capable of listening for ASCII commands*Check on VMS and camera health using SNMP*Supports IPv4 and IPv6 cameras*Enables and supports Risk Management Framework (RMF),incorporates FIPS 140-3 validated cryptographic modules*TLS-based encryption over HTTPS Note: MAF/Letter of Authorization from Original Equipment Manufacturer (OEM) on the same and specific to the tender should be submitted before delivery of the Material.

SERVER - Video Management Server support for 128 Cameras SITC of Rack Server Operating System Microsoft Windows 10 IoT Enterprise 64-bit (LTSC)Memory 16 GB DDR4 ECC2x M.2 SSDs 240 GB (RAID 1)Processor Intel® Xeon® Silver 4310Dell iDRAC Controller iDRAC9 Basic NVIDIA Quadro P1000 (4 GB memory)Video Outputs 4x Mini DisplayPort (DP++) 1.42 x Gigabit Ethernet (1000Base-T) portsIP Version IPv4 and IPv6Recording Throughput 450Mbps Bandwidth3 year warranty. Note: MAF/Letter of Authorization from Original Equipment Manufacturer (OEM) on the same and specific to the tender should be submitted before delivery of the Material.

HARD DISK - Supply, Installation, Testing & Commissioning of 200 TB Video Hard Disk.

WORKSTATION - Supply, Installation, Testing & Commissioning of Client WorkStation with CPU of Intel Core i7 Processor, With 8GB RAM, 1 GB Graphic Card, and 500 GB HDD.

24 PORT SWITCH - Supply, Installation, Testing & Commissioning of POE Layer II managed ethernet switch, 24 port RJ45 10/100/1000 T with 2 nos. OFC Port. Switch shall have minimum 24 nos. 10/100/1000 Base-T ports with PoE+ capability and minimum 370W of PoE Power and additional 4 nos. of SFP uplink ports loaded with 2 nos. of SMF modules. Shall have minimum 56 Gbps of switching fabric and 80 Mpps of forwarding rate. Should support IEEE Standards of Ethernet: IEEE 802.1D, 802.1s, 802.1w, 802.1x, 802.3ad, 802.3x, 802.1p, 802.1Q, 802.3, 802.3u, 802.3ab, 802.3z, 802.3af, 802.3at. Switch should support port security, DHCP snooping, Dynamic ARP inspection, IP Source guard, BPDU Guard, spanning tree root guard IPv6 QoS and IPv6 ACL.

8 PORT FULLY LOADED LIU - Supply, Installation, Testing& Commissioning of 8 PORT Fully loaded Fiber LIU including connection as per specifications & complete as required.

SFP MODULE - Supply, Installation, Testing & Commissioning of Gigabit SFP Module as per specifications complete as required.

6 CORE OFC CABLE - Supply installation Testing and Commissioning of 6 Core OFC Cable..

STP CAT 6A CABLE - Supply, Installation, Testing & Commissioning of STP CAT 6A Cable..

6U RACK - Supply installation Testing and Commissioning of 6U Rack Wall Mount..

UPS - Supply installation Testing and Commissioning of online 3KVA UPS 30 Mins Backup.

AUDIO VIDEO SYSTEM

SITC of 100" or better 4K (3,840 x 2,160), Direct (Full Array LED), Professional Slim Blade Stand Display with 4K HDR Processor X1,HDR (HDR10, HLG, Dolby Vision), Native Contrast ratio upto 6,000:1, Response time 6ms, Peak Brightness 850 cd/m² or better, 4K X-Reality PRO, TRILUMINOS DISPLAY technology, 24/7 Portrait ,Tilt functionality, Flexible Content Layout with HTML5, 16GB On Board Storage, Motion flow XR,HDCP 2.3 (HDMI) / RS232 / USB/ RJ45 / Wi-Fi with In-Built Bluetooth / 20W Speakers / Android™ OS system, Viewing angle 178 degree, Pro Mode, Pro Display using Apple AirPlay & Chromecast etc.

SITC of 65" or better 4K (3,840 x 2,160), Direct (Full Array LED), Professional Slim Blade Stand Display with 4K HDR Processor X1,HDR (HDR10, HLG, Dolby Vision), Native Contrast ratio upto 1200:1, Response time 6ms, Peak Brightness 440 cd/m², 4K X- Reality PRO, TRILUMINOS DISPLAY technology, 24/7 Portrait ,Tilt functionality, Flexible Content Layout with HTML5, 16GB On Board Storage, Motion flow XR,HDCP 2.3 (HDMI) / RS232 / USB / RJ45 / Wi-Fi with In-Built Bluetooth / 20W Speakers / Android™ OS system, Viewing angle 178 degree, Pro Mode, Pro Display using Apple AirPlay & Chromecast etc.

SITC of PTZ Camera for Video conferencing purpose having - 1/2.5” high quality, 8.4MP CMOS sensor, 3840x2160 pixels, 4K@ 60fps, 12x Optical Zoom, 16x Digital Zoom, 80.8° Field of View, 200+ Pre-sets, USB 3.0, HDMI, RJ45,3G-SDI, USB. etc as required.

8x8 HDMI Matrix Switcher having 8 HDMI Input and 8 HDMI Outputs 4K, Matrix Switching.

HDMI to USB 3.0 media converter with Audio Input.

HDMI Cable 15 Meter, 4K Kramer,

HDMI Cable 10 Meter, 4K Kramer,

USB Cable 10 Metr

SITC of Digital Chairman Discussion Unit with builtin Digital Signal Processing, Unit with Priority and Next-in-Line Configuration, Priority button silences all delegate microphones and allows only the chairperson to speak, Next-in-line button gives the floor to the next speaker in a waiting list of speakers who requested to speak, User Button with Feedback, Shielded microphone, immune to mobile phone interference, High-quality integrated loudspeaker, Headphone output with Volume Adjustment, Loop-through, daisy-chain cabling, Different LED Signalling for Mic On/Off OR Request to-Speak Push Button, Audio Quality 16Bit digital, Frequency Response: 30Hz-15kHz.

SITC of Digital Delegate Discussion Unit with built-in Digital Signal Processing, User Button with Feedback, shielded microphone, immune to mobile phone interference, High-quality integrated loudspeaker, Headphone output with Volume Adjustment, Loop-through, daisy-chain cabling, Different LED Signalling for Mic On/Off OR Request to-Speak Push Button, Audio Quality 16Bit digital, Frequency Response: 30Hz-15kHz.

SITC of gooseneck Microphone 500mm or better having following specifications Transducer principle Back electret (condenser) Operating principle Pressure gradient, Polar pattern Unidirectional, cardioid ,Nominal conditions Signal to noise ratio > 70 dB(A).

SITC Of conference cable RJ 45 2 Mtr

SITC Of conference cable RJ 45 20 Mtr

Supplying, Installation, testing and commissioning of Amplifier with 2 x 300W at 8ohm & 70/100V Line, Signal to Noise ratio >97dB, THD

SITC of Wall/Ceiling Mount Speaker fo 50 W @8 ohm, 70/100V Transformer Tap, Senstivity 86dB, 106db SPL, Two way speaker having 5.25" Speaker and 3/4" Tweeter with necessary mounting arrangement.

Supply, Installation, testing and commissioning of Digital Signal Processor with Multipurpose software based digital audio signal processor with a total of 8 balanced analog microphone/line level audio inputs with AEC and 8 balanced analog microphone/line level audio outputs. In addition to the fixed 8x8 analog audio I/O, it should also have a software definable bank of 8 balanced analog audio Input/output channels where each channel can be independently configured during design or run time as either a microphone/ line level input or a microphone /line level output; RJ 45 LAN Control, with standard accessories complete as required.

Microphone cable

Digital podium : Mild Steel, tray for keyboard, 21" interactive monitor with Motorized Positioning up or down as per user convenience, Connectivity for Laptop, Visulaiser, control for projector ON/off, Screen Up/Down, etc as required.

Equipment Rack 24U, 19" with 600mm Depth

Network Switch 10 Port.

SITC of 65" or better 4K (3,840 x 2,160), Direct (Full Array LED), Professional Slim Blade Stand Display with 4K HDR Processor X1,HDR (HDR10, HLG, Dolby Vision), Native Contrast ratio upto 1200:1, Response time 6ms, Peak Brightness 440 cd/m², 4K X- Reality PRO,TRILUMINOS DISPLAY technology, 24/7 Portrait ,Tilt functionality, Flexible Content Layout with HTML5, 16GB On Board Storage, Motionflow XR,HDCP 2.3 (HDMI) / RS232 / USB / RJ45 / Wi-Fi with In-Built Bluetooth / 20W Speakers / Android™ OS system, Viewing angle 178 degree, Pro Mode, Pro Display using Apple AirPlay & Chromecast etc.

SITC of 4K Auto Frame Capmera with Microphone array with intelligent USB camera of output of up to 4K (3840x2160) @30 frames and Built-in with 96dB speaker, Bluetooth WiFi infrared, microphones array, built-in Beam Forming (BF) microphone, and audio pickup distance of 6 meters. 4K AF CameraSoundbar should supports HDMI 2.0 output and USB3.0 output with all required cables.

LIFTS

Supply and fixing lift shaft suitable for 13 Passengers Lift for 3 stop 3 opening (all opening on same side) with travel height 6 Mtr and overhead 4200 mm including pit depth of 1600 mm of M.S. Pole & Chanel frame enclosed with ACP Panels & for sealing the top ray of lift shaft so the rain water cannot enter in lift shaft including labors all work complete as per directions of Engineer-In-Charge. Note: The successful bidder will essentially submit the detailed structural drawing, floor plans and elevation drawings within 15 days after award of work which will be then vetted by NIT/IIT & the successful bidder will also submit the stability report duly examined and issued by NIT/IIT. All above work will be in the scope of successful bidder and nothing extra will be paid on this account.

S/I/T/C of Dumb waiter of 100 Kg capacity,0.3 M/Se speed suitable to serve G + 1 (02 stop/02 opening) with AC variable voltage & variable frequency drive (VVVF drive) 415 volts, 3 phase, AC supply,50 Hz with gearless motor, car enclosure made out of stainless steel hairline finish with flooring stainless steel 1.2mm thick including all standard accessories call and send control operation from landings, complete all as specified including labours.

CREDIT OF DISMANTLE ITEMS

Credit of dismantle of old Iron Scrap like steel windows / door frames, MS grills, MS bars, GI pipe and fittings etc.

Credit of dismantle of old Wooden Scrap like old flush doors, wooden frames, ply, board etc.

Credit of dismantle of old PVC scrap like PVC cistern, PVC tanks, PTMT fittings etc.

Switches & Sockets.

Copper / Aluminum wires

1' x 4' conventional type / Led fittings

2' x 2' Led / conventional type fittings

18/20 watt led channel fittings & 12watt /18-watt fittings

1200mm Ceilings fans

400 mm wall fan

10" / 12" / 15" / 18" Exhaust fan

SPN DB's

VTPN DB's

MCCB Box with MCCB

Type of MCB's

90 watt Faced Light

Dismantled Fire Alarm System.

Confoss Construction (BID ID -3143178)

DELHI ENGINEERSCONSTUCTION COMPANY (BID ID -3146882)