KMC/WS/CBPS/2025-26/06

CHAPTER - VIII SUPPLYING OF MATERIALS 8.8 Ductile iron double flanged manually operated sluice valve generally conforming to IS : 14846, having body, door, dome, gland in graded ductile iron to IS 1865, four faces and spindle nut of gun metal to IS : 318, inside screw non- rising stainless steel AISI-410 spindle valves suitable formaximum working pressure of 10 kg/cm... and body tested 15 kg/cm..., flanges flat faced and drilled to IS: 1538 :1993. Valves tested by closed end method only. 350mm and above valves are complete with enclosed gear box with anti friction device.Diameter in mm 300

CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 300

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3 M.S. Pipes 2.3.1 Gas cutting of M.S. pipes and/or M.S. plates of different thickness all complete as per specification and direction of the Engineer-in- Charge. Thikness in mm 5mm to 8mm thick plate

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3.4Field welding of machined ends of pieces of M.S pipes and specials forlaying the same inside trench/over ground by means of electric arc welding as per relevant ISspecification using standard electrodes including edgepreparation and charges of deployment of electric generator set with fuel, lubricant, and all other tools and plants all complete as per specification and direction of Engineer-in-Charge. [ Engineer-in-Charge shall approve the electrodes for arc welding before use ]Throat thickness in mm 8mm

CHAPTER - VIII SUPPLYING OF MATERIALS 8.16Sypply of E.R.W.M.S. (Electrical Resistant Welded M.S.) black pipe of ISI mark as per relevent IS Specification ( heavy quality ) having wall thick-ness not less than 8 mm. [N.B.: The rates for supply of TATA Make pipe will be arrived at by adding 20% of the corresponding rates ] Diameter in mm (Internal) 300

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.4Valves 2.4.1 Lowering, fitting and fixing of all types of valves in proper position and alignment using chain pully block or crane(for diameter above 250 mm) by providing temporary support,as required,gaskets,nuts& bolts etc.all cornplete as per specification and direction of the Engineer-in-Charge.[The rate Includes cost of flange joints]300mm dia.

CHAPTER - VIII SUPPLYING OF MATERIALS HIRE CHARGES OF MACHINERIES 8.26 Hire charges of moveable crane with fuel & manpower having load handling capacity upto 14MT with the 45 deg. moveable arrangement & the boom length of 40 feets for loading & unloading of various materials / accessories of water supply works. For minimum engagement of 8 hrs. In a day

CHAPTER - VIII SUPPLYING OF MATERIALS HIRE CHARGES OF MACHINERIES 8.28Hire charges of lighting generator of capacity 5KVA including fuel, mobil, operator, carriage etc. including all complete for water supply works. For minimum engagement of 8 hrs. In a day

CHAPTER - VIII SUPPLYING OF MATERIALS 8.13 Ductile iron Single Chamber type air release valve having small orifice elastic ball resting on gun metal orifice nipple large orifice vulcanite ball seating on moduled seat ring, valve with built-in-Kinetic features, isolating sluice valve mounted in horizontal position and operated by a metre wheel gearing:inlet faced and drilled to IS 1538 Table 4 & 6. valve suitable for maximum working pressure of 10 kg/CM2 Diameter in mm 100

CHAPTER - VIII SUPPLYING OF MATERIALS E. E. R. W. MS BLACK PIPE 8.15 Sypply of E.R.W.M.S. (Electrical Resistant Welded M.S.) black pipe of ISI Mark as per relevent IS Specification ( heavy quality ) having wall thickness not less than 5 mm. [N.B.: The rates for supply of TATA Make pipe will be arrived at by adding 20% of the corresponding rates ] Diameter in mm (Internal)100

CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 100

SECTION 1. ------------BUILDING WORKS (K) PAINTING, VERNISHING ETC A. ORIGINAL WORKS 1 (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc (This item is applicable to new work or old work when the original surface has been exposed by removal of old paint.)

BUILDING WORKS (K) PAINTING, VERNISHING ETC?(A) ORIGINAL WORKS.(2)(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(b) On steel or other metal surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white)

BUILDING WORKS ( C ) Brickworks,Concrete Works etc A. BRICK WORKS 8. Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth

SECTION 1. ------------BUILDING WORKS (I) PLASTERING, POINTING ETC. A. ORIGINAL WORKS 1.Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](iv) 1:2 cement mortar (to be used in floors and for specialworks) (a) 15 mm. thick plaster

CHAPTER - VIII SUPPLYING OF MATERIALS 8.8 Ductile iron double flanged manually operated sluice valve generally conforming to IS : 14846, having body, door, dome, gland in graded ductile iron to IS 1865, four faces and spindle nut of gun metal to IS : 318, inside screw non- rising stainless steel AISI-410 spindle valves suitable formaximum working pressure of 10 kg/cm... and body tested 15 kg/cm..., flanges flat faced and drilled to IS: 1538 :1993. Valves tested by closed end method only. 350mm and above valves are complete with enclosed gear box with anti friction device.Diameter in mm 450

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3.7Supplying and fabricating 20 mm to 32mm thick (finished thickness) M.S flange. properly ribbed, one face machined, including drilling holes as perstandard table, fitting and fixing the same with M.S. pipe by electric arc welding as per relevant I.S. specification using standard electrodes and direction of the Engineer-in-Charge. [ The Engineer-in-Charge shall approve the electrodes for arc welding before use] 450mm dia

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.4Valves 2.4.1 Lowering, fitting and fixing of all types of valves in proper position and alignment using chain pully block or crane(for diameter above 250 mm) by providing temporary support,as required,gaskets,nuts& bolts etc.all cornplete as per specification and direction of the Engineer-in-Charge.[The rate Includes cost of flange joints]450mm dia.

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3.5 Fabricating M.S. pipes of different diameter in shop out of 8mm to12mm thick M.S plates supplied depart-mentally, cutting the plates to exact size & shape by gas cutting device and/or by adopting any other approved type of mechanical means, bending the same in true curvature by template and rolling machine of approved design including proper marking, levelling joints followed by electric arc welding as per relevant I.S. specification - longitudinal and circumferential, as necessary, usiug standard electrodes including edge preparation, electricity charges and hydraulic testing of the fabricated piece all complete as per speci-fication and direction of the Engineer-in-Charge. [The Engineer-in-Charge shall approve the electrodes for arc weldingbefore use.]a) Diameter from 450 mm & upto 600 mm.i) 8mm thick plate.

M.S PLATE AS PER IS : 2062 -2011/LATEST REVISION, MAKE : SAIL/ TATA/JINDAL 1.B) ABOVE 2 MM UPTO 10 MM THICKNESS (USOR (M&E) WEF 10TH MAY,2022, IRRIGATION & WATERWAYS DEPARTMENT, GOVT. OF WB)

CHAPTER - VIII SUPPLYING OF MATERIALS 8.16Sypply of E.R.W.M.S. (Electrical Resistant Welded M.S.) black pipe of ISI mark as per relevent IS Specification ( heavy quality ) having wall thick-ness not less than 8 mm. [N.B.: The rates for supply of TATA Make pipe will be arrived at by adding 20% of the corresponding rates ] Diameter in mm (Internal) 200

CHAPTER - VIII SUPPLYING OF MATERIALS 8.8 Ductile iron double flanged manually operated sluice valve generally conforming to IS : 14846, having body, door, dome, gland in graded ductile iron to IS 1865, four faces and spindle nut of gun metal to IS : 318, inside screw non- rising stainless steel AISI-410 spindle valves suitable formaximum working pressure of 10 kg/cm... and body tested 15 kg/cm..., flanges flat faced and drilled to IS: 1538 :1993. Valves tested by closed end method only. 350mm and above valves are complete with enclosed gear box with anti friction device.Diameter in mm 200

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.4Valves 2.4.1 Lowering, fitting and fixing of all types of valves in proper position and alignment using chain pully block or crane(for diameter above 250 mm) by providing temporary support,as required,gaskets,nuts& bolts etc.all cornplete as per specification and direction of the Engineer-in-Charge.[The rate Includes cost of flange joints]200mm dia.

CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 200

MATERIALS AND LABOUR 1. Building (B) Labour Rates Per Diem : 17)Fitter Mechanic. Note: (I)The above rates of labour are exclusive of 10% contractors profit and 1% Labour welfare cess which would be admissible to the Contractors, but contractual percentage will not be applicable. (II) The workersemployed on high rise building or any structure over 30 ft in height and also workers engaged in Tunnel shall be paid 20% extra wages.

MATERIALS AND LABOUR 1. Building (B) Labour Rates Per Diem : 18)Fitter Mechanic (Helper). Note: (I)The above rates of labour are exclusive of 10% contractors profit and 1% Labour welfare cess which would be admissible to the Contractors, but contractual percentage will not be applicable. (II) The workersemployed on high rise building or any structure over 30 ft in height and also workers engaged in Tunnel shall be paid 20% extra wages.

MATERIALS AND LABOUR 1. Building (B) Labour Rates Per Diem : 3)Mazdoor (Male). Note: (I)The above rates of labour are exclusive of 10% contractors profit and 1% Labour welfare cess which would be admissible to the Contractors, but contractual percentage will not be applicable. (II) The workersemployed on high rise building or any structure over 30 ft in height and also workers engaged in Tunnel shall be paid 20% extra wages.

Sub Total