ADDN ALTN AND SPL REP TO BLDG P-45 ADDN ALTN AND SPL REP TO RADIOLOGY ROOM EXTN BLDG P-70 AT INS TANAJI SPL REP TO BLDG P-48 P-49 AT NSB AND ADDN/ALTN AND SPL REP TO NCN SERVER ROOM AT NAD TROMBAY UNDER GE (NW) MANKHURD

Amount

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

M&L for 15 mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing surfaces even and smooth complete all as specified and directed Note: (i) The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with ready mix plaster and nothing extra shall be payable on this account. (ii) This item shall be operated only for the locations where the thickness of existing adjoining plaster is to be matched

M& L rendering 10 mm thick in CM 1:3 as in ceiling, finished even & smooth surfaces complete all as specified and directed.

M&L for 20 mm thick polymer modified readi mix cement based plaster on the wall surfaces including finishing the surfaces even and smooth, complete all as specified and directed. Note : The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with the ready mix plaster and nothing extra shall be payable on this account.

Supply only integral water proofing compound complete all as specified and directed.

Chipping, removing carefully loose/damaged concrete incl plastering (total thickness upto 60mm ) from RCC surfaces of columns, beams,Chajas, soffits of slabs etc by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land, complete all as specified and directed. Note: 1. Hard concrete shall not be removed by force. Note : 2. Item No 6.00 will not be applicable for the location/areas where item No 1.00 is applicable.

M&L for cleaning existing reinforcement by sand blasting with suitable pump as directed by the GE and wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed.

M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed .

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR Monobond SBR of M/s. Krishna Conchem or Shalicrete URP of STP Ltd as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit or Shalifix RM SG 01 of STP Ltd, while the bonding agent is still sticking upto 20mm thickness including levelling, profiling etc complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Monolith-PMM) OR Polymer mortar HB of Dr Fixit or Shalifix RM SG 01 of STP Ltd , while the bonding agent is still sticking upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed.

M&L for leakage / seepage proof coating consisting of preparing the new/old surfaces of existing exterior walls, parapet walls, chajjas etc. and applying Primeseal primer of M/s Dr Fixit or equivalent chemical of M/s STP Ltd or one coat of Chemstic PDE 600 elastomeric coating (and allowing to dry for 8hrs) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of M/s Dr Fixit with DFT 100microns or Shalicryl 215 of M/s STP Ltd or Chemstic PDE 600 elastomeric coating (the surfaces after painting one coat shall be allowed to dry for 6 to 8hours before application of next coat) including necessary scaffolding etc complete all as per manufacturer instructions and all as specified & directed. Notes: The aforesaid treatment shall be got executed by the contractor from the authorised applicator of the manufacturer(s) and also necessary authenticated documents on account of above shall be submitted by the contractor to the GE.

M& L for complete removal of existing treatment on surfaces of walls and applying two coats of oil bound distemper over chalk whiting including 3 mm thick wall care putty applying on walls for smooth finish complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubish off the premises complete all as specified & directed.

S&F Vitrified light shade ceramic tiles 10 mm thick (square/rectanglar) polished area of each tile not exceeding 0.36 sqm ,in floors etc & including set and jointed in neat cement slurry and pointed in white or Coloured cement to matched laid over 15mm thick bedding layer of CM 1:6 complete all as specified and as directed.

All as per ser item No 15 above but area of tile exceeding 0.36 sqm but not exceeding 1 Sqm

All as per item No 15 above but as in skirting /dado laid over & including 10 mm thick rendering layer in CM 1:4 complete all as specified and as directed

M&L for non skid colour ceramic tiles 400x400x6 to7mm thick in floors etc set and jointed in neat cement slurry and pointed with colour cement to match the shade over & including 15 mm thick CM 1:6 screed bed for laying floor finishes all as specifed and directed..

All as per items No 18 above but in skirting or in dado over & including 10 mm thick rendering CM 1:4 complete all as specified and directed

M&L for colour glazed ceramic tiles 300x200x6 to 7mm thick set and jointed in neat cement slurry and pointed with coloured cement as in skirting/dados over & including 10mm thick rendering in CM 1:4 as in backing coats of tiles finished the surfaces rough to receive tiles etc complete all as directed and specified.

M&L for non skid coloured ceramic tiles 300x300x6 to7mm thick in floors etc set and jointed in neat cement slurry and pointed with coloured cement to match the shade over & including 15 mm thick CM 1:6 screed bed for laying floor finishes all as specifed and directed..

S&F in repairs 15mm bore angular stopcock with wall flange fitted complete all as specified and as directed

S&F cast iron Nahani trap 100mm dia out let including grating connecting jointing to waste pipe with lead jointing and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs 15mm bore pillar taps; of cast copper alloy with capstan; head chromium plated screwed down with pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe& fixed complete all as specified

S&F in repairs CP grating doom 125mm dia of size complete all as specified and directed.

S & F in repairs Vitreous China Wash hand basin white, flat back, size 550x400 mm size (flat back or angle back type)excluding taps, waste, chain and plug and procelaim stopper but including cutting for and pinning ends of brackets or erecting stand.incl taking down pillar tap complete all as specified and directed

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each including complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame) area not exc 1.5 Sqm each including complete all as specified and directed.

S& F second class hard wood plain, solid straight chowkats and frame, wrought framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good disturbed surfaces of wall complete all as specified and directed

Supply & Fixing solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, fixed in opening as per specification & drawings complete all as specified and as directed.

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2010 complete all as specified and directed.

S&F 100 mm long stainless steel butt hinges fixed with stainless screw complete all as specified and directed.

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length complete all as specified and directed.

S&F aluminum anodised barrel tower bolts of extruded section of size 100 mm length complete all as specified and directed.

S&F 150 mm extruded aluminum alloy handles, fabricated type anodised complete all as specified and directed.

S&F aluminum anodised sliding door, bolts with hasp and staple ( bolt type ) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy, length of bolts 250 mm complete all as specified and directed..

S&F bands, straps , supports or stays for rain water, ventilating pipes including bolts, clamps, hold fasts etc and similar small articles, mild steel Fe-410-0 or Fe-310-0 all as specified & directed.

M&L PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in hold fast, bed plate etc including necessary form work complete all as specified and as directed.

M& L for preparation surfaces of new or old previsouly untreated wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan “Pedestal Pattern” coloured with wc seat cover coloured closed pattern with flat bottom and mild steel chromium plated or aluminized hinging device including pvc flush pipe and joints etc and connection to drain, flushing, pipe, anti- syphonage pipe, and fixing arrangements with fixing bolts etc, complete all as specified and directed

S&F in repairs 15 mm bib taps two way cock, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated complete all as specified and directed

S&F in repairs hand shower (health Faucet) with 8mm dia 1 mtr Long flexible tube & wall hook complete all as specified and directed

S&F in repairs high level/low level PVC flushing cistern with PVC flush pipe, brackets, and PVC connection complete of 10 Ltr capacity complete all as specified and directed

S & F in repair Vitreous China Half stall urinal White complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement including CP spreader, waste pipe complete all as specified and directed

S&F urinals valve auto closing system with built in control cock &wall flange ( pressmatic) long screwed shanks and fly nut screwed for 15 mm bore pipe, complete all as specified and as directed (Make : Jaquar Cat No:PRs-077 or equivalent make specified in PS)

Dismantling / taking out existing water proofing treatment (including cement screed bed below) from roof including loosened cement plaster and exposing the top surface of RCC slab and removing rubbish, etc outside MD land complete all as specified and as directed.

M & L for roof water proofing treatment with heavy duty, reinforced heat insulative acrylic polymer modified liquid membrane of Shalicryl LM HI of STP Ltd or Sika topseal-109 HI of Sika India Ltd or equivalent over a coat of primer of same brand including preparation on old surface.(For non-accessible roof) complete all as specified and directed Note : - (i) Application will be done with authorized applicator of respective company only. (ii) Mixing & rate of application will be strictly as per manufacture instruction only.

Taking down existing aluminium joinery of any description (frame/ shutters) with all fittings (but excluding grills) complete all as specified and directed.

S&F standard aluminium section powder coated (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by GE ) as in frame, shutters for doors, window / ventilators, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, shall be measured and paid separately as supply only under respective item.

Taking down carefully existing aluminium sliding window shutters, taking down of existing broken plain sheet glass from aluminium sliding window shutters including existing rubber gasket complete, supply and fixing 5 mm thick plain sheet glass with and including provision of new rubber gasket and re-fixing the shutters in existing position, complete all as specified and directed.

Taking down carefully existing aluminium sliding window shutters, taking down of existing stainless steel wire mesh from aluminium sliding window shutters including existing rubber gasket complete, supply and fixing stainless steel wire mesh of dia 0.36 mm and average width of aperture 1.40 mm with and including provision of "U" clip, re-fixing the shutters in existing position, complete all as specified and directed.

S&F in repairs aluminium anodised Grills of approved design for window / ventilators and fixing with F/U channel including drilling as required in RCC sections in rectangular or architectual type balcony opening in existing building, complete all as specified and directed. Note: The Grills shall be of Model DG-100/DG-102 of make as specified in PS.

Dismantling of brick work /stone boulders built in cement mortar including all quions arches, pillars etc complete all as specified and as directed.

M & L for brick work in CM (1:6) using sub class 'B' bricks strainght or or curved as curved as required on plan exc 6mtrs mean radius etc complete all as specified and directed

Demolition of stone slabs and tiles laid beded and pointed in any mortar of any description or thicknes in floors , aprons etc complete all as specified and directed

M & L for Machine cut cudappah stone slab 20- 25mm thick, laid and mixed with pigment to match the shade of the slab window cills and jambs to full thickness of wall fixed in steps over cement screed bed 10mm thick in CM 1:4 and jointed with grey cement paste and slurry including rubbing and polishing complete all as specified and directed

Demolition cement concrete( reinforced )in any description and in any postion not otherwise specifically provided complete all as specified & directed.

Supply 9 mm thick prelaminated particle, board, interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to aluminium frame work complete all as specified and directed

M&L for mild steeel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and bindings with mild steel wire (annealed) not less than 0.9mm dia, or securing with clips, complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall etc and applying two coats of 100% anti fungal acrylic exterior emulsion paint over one coat of primer all as per manufacturer's instructions including necessary scaffoldings upto 24 mtr etc, complete all as specified and directed.

M & L for preparation of old treated surfaces of any description and at any position and applying one coat 100% anti fungal acrylic exterior emulsion paint all as per manufacturer's instructions including necessary scaffoldings upto 24 mtr etc, complete all as specified and directed.

S&F Non Skid ceramic joint free tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matched laid over 15mm thick badding layer of CM 1:6 complete all as specified and as directed.

M&L for coloured glazed ceramic tiles 450x350 to 7mm thick set and jointed in neat cement slurry and pointed with coloured cement as in skirting/dados including 10mm thick rendering in CM 1:4 as in backing coats of tiles finished the surfaces rough to receive tiles etc complete all as directed and specified.

M&L RCC 1:1/2:3 type 'A-1' (using 20mm graded stone aggregates) as in lintels upto 1.5 metre clear span, cills, steps, seismic and other similar bands and the like including weathering slightly rounded or chamfered angles and throating as directed, also including provision of necessary form work, complete all as specified and directed. Note: Payment for reinforcement shall be made for separately.

M&L for 20 mm thick granite (of any type) slabs machine cut in skirting and dado , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing over screed bed or bedding layer 15 mm thick in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match Colour is approved by GE complete all as specified and as directed.

S&F for 35 mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides and fitted to chowkhats complete all as specified and as directed.

S&F Glazed and Skelton shutters, 35 mm thick of Second class hard wood open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) (Door Shutters) complete all as specified and as directed.

M&L for Preparing surface of wood and wood based materials, steel and iron work, new or old, treating ends of posts, coal tar black paint on back of chowkats area exc 0.10 Sqm but not exc 0.5 Sqm each complete all as specified and as directed.

M&L for treating with tar or coal tar black paint on back of chowkats, ends of posts, holdfasts etc. area not exc 0.1 Sqm each complete all as specified and as directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F Floor door stopper of Aluminium alloy body and tongue, overall length of cover plate 140 mm , anodized, with hard drawn steel spring , fixed to shutters complete all as specified and as directed.

Taking down carefully aluminium sliding window shutters from the frames or chowkhat and supply and fix New locking arrangement of Aluminium in place of old one and re-fixing the same shuters in existing position etc, complete all as specified and directed

Demolition of brick/cement concrete (unreinforced) / pcc tiles from existing roof/terrace etc and also removing/taking down of existing water proofing treatment of any thickness in any position including cleaning the surfaces of roof etc with wire brush complete and removing the retreived debris out side MD land, all as specified and directed.

M&L for PCC (1:2:4) type B-0, using 12.5mm graded stone aggregate as in levelling course over RCC roof surface to achieve required slope, benching etc including making rounded or chamfered on edges mixed with WPC as per manufacturer's instructions, complete all as specified and directed.

M&L cement plaster (1:3) with 10mm thick to be finished smooth without using extra cement mixed with WPC @2% by weight of cement, , complete all as specified and directed. Note : WPC shall be measured and paid separately as supply only.

Demolition cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified & directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75mm thick, with expansion joints & top surface finished even and smooth without using extra cement etc complete all as specified and directed.

Dismantling cast iron water pipes (any size or pattern ) including all fittings, ( measure overall as fixed along the centre line over fitting and accessories ) all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls all complete all as specified and directed.

Supply & fix in repairs15mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Supply & fix in repairs 20mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

M&L for plain cement concrete type D -2 1:4:8 (40 MM greade aggregate) 100 mm thick laid in sub base for floor complete all as specified and directed

M& L Pre Polished Chequred cement concrete tiles 30cm x 30 cm x 25 mm thick, set, jointed and pointed in near cement slurry in floors with mixture of grey white cement in equal proportions over screed bed or bedding layer of mortar 20 mm in cement mortar 1:6 complete all as specified and as directed

M & L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice laminations, fixed with screws to timber frame work complete all as specified and as directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms etc including screed bed 15 mm th in CM (1:6) complete all as specified and as directed.

S & F for aluminium (Die cast body) hydraulically Door closer regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified & directed.

Supply Only 5.50 mm thick sheet glass, ordinary quality for wooden/aluminium joinery, exc 0.50 Sqm in each pane complete all as specified and directed.

M&L for suspended False ceiling with aluminimum grid work system of size 605 x 605mm with runners aluminimum anodised main Tee of section 35x35x1.5mm thick , cross T of section 25x25x1.5mm thick & Aluminimum anodised angle of size 25mm x 25mm x1.5mm thick fixed along side of wall with wooden plugs & hanging from ceiling/ MS purlins with and including 4mm dia GI wire suspension system (up to 1200mm length), adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40mm x 3mm size, 60mm long and expansion hold fasteners 12.5mm dia 40mm long, including necessary scaffolding etc, complete all as specified and directed. (Note: Ceiling board / tiles shall be measured and paid separately).

M & L 12 mm thick Perforated particle board/tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid as in ceiling complete all as specified and directed

Complete removal of existing treatment, applying 3 mm thick wall care white cement base putty and applying two coats of plastic emulsion paint over one coat of priming paint plaster coat including preparation of surfaces on walls surfaces of any description over 10 cm girth or width, not otherwise described.

S & F mild steel chromium plated, decorative curtain rod, 20 mm dia, complete all as specified and directed.

S & F mild steel decorative, decorative brackets for 20mm dia curtain rod, complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc by meachincal means complete all as specified and directed

M&L for preparing new plastered surface of walls, and applying two coat of Distemper oil emulsion over a coat 3mm thick white cement base wall care putty complete all as specified and directed

M&L for preparation of newly plastered surfaces of celings and applying three coats of white wash complete all as specified and directed

M& L for preparing old surfaces walls of distempered & painted surfaces and applying one coat of oil bound distemper complete all as specified and directed

M&L Preparation of old plastered or un-plastered surface of ceiling and applying one coat of white wash complete all as specified and directed

M&L 100 mm thick Cement concrete type B1, 1:2:4 (using 20 mm graded aggregate) as in flooring finishing cement concrete even & smooth with out using extra cement complete all as specified and as directed

M&L Machine pressed precast concrete interlocking paver block Coloured any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade over and including 25 mm thick sand cushion complete all as specified and directed

M&L 75 mm thick plain Cement concrete type D2, 1:4:8 (using 40 mm graded aggregate) as in sub base of flooring complete all as specified and directed

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over screed bed or bedding layer of mortar 20 mm in cement mortar 1:6 complete all as specified and as directed.

All as per ser item No 102 above but skirting with backing coat of 10 mm in CM (1:4) complete all as specified and as directed.

S&F in repairs Steel rolling shutters, 1mm thick of laths with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete; push pull or manual type complete all as specified and as directed.

M& L for preparation of new steel and iron surfaces of any description , over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a priming coat of red oxide zinc chrome complete all as specified and directed.

M&L for PCC 1:2:4 type B2(20mm graded aggregate) as in surface channels and drains complete all as specified & directed.

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 5 star rating and EER 3.80 of capacity 1.5 Ton electric driven single phase 230 Volt complete all as specified and directed.

Supply and fixing earthed metal clad socket outlet with earthed plug top 20Amp capacity , sheet metal enclosed and one 20 Amp MCB SP all as specified and diredted.

M&L for sub main wiring with two single core 4 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through rigid flexible where applicable non metalic PVC casing caping with and including PVC insulated 4 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed including taking down of old sub main wiring complete all as specified and directed. Note : 1. Two runs of Single core cable, one run of earth wire & PVC Cassing Capping will be measured and paid one unit.

M & L for point wiring complete with proper colour coding, using 1100 Volts grade, 1.5 Sqmm, PVC insulated, FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked drawn in and including PVC casing caping (minimum 25mm width) fixed on the surfaces of wall, ceiling etc with all accessories, fittings, PVC junction boxes etc, sunk pressed steel terminal boxes not less than 2 mm thick, 50 mm deep covered with 3mm thick plastic laminated sheet top cover fastended with chromium plated brass screws, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly for one light point /fan/bell point controlled by one one way switch, complete all as specified and directed.

All as per item No. 110 above but One 5A 2pin/3pin socket out let multipurpose on the same board with other switches complete all as specified and directed.

All as per item No. 110 above but One 5 Amps 2 pin / 3 pin switch socket outlet multipurpose on Independent Board complete all as specified and directed.

All as per item No. 110 above but wiring complete with 2.5 Sqmm for 3 pin 15A switch socket multipurpose on independent board complete all as specified and directed.

S&F Switch Socket combination 2 in 1 , 5 Amps, flush type, 5 Pin, 230 Volts, complete all as specified and directed.

S & F MCB DB, 8 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete all as specified and directed. Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating.

S & F MCB, SPN, 40 Amps, 240 / 415 Volts, 50 Hz 10 KA Breaking capacity, complete all as specified and directed.

S & F MCB, SP, 05 to 32 Amps, 240 Volts, 10 KA Breaking capacity, C-series, complete all as specified and directed.

Taking down carefully and Refixing in position after repair to existing LED tube light fitting any watt any type, complete all as specified and directed.

Taking down carefully old unserviceable copper / aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings and making good disturbed suface of wall, floors, ceiling etc complete all as specified and directed.

S&F Switch Piano 5 Amps, 250 Volts, one way, flush type, complete all as specified and directed.

S & F in repairs Ceiling Rose, surface bakelite, three terminals, AC, 230 Volts complete all as specified and directed.

S & F in repairs Switch Socket combination 5 in 1, 15 Amps, 6 pin multipurpose, flush type, 230 Volts complete all as specified and directed.

S & F in repairs Ceiling fan regulator electronic stepped type, AC, 230 Volts, flush type complete all as specified and directed.

S&F sheet metal enclosure, 32A single pole and neutral with a two pin and earth plug and socket complete in metal clad board (Industrial type) with one single pole MCB 32 Amp fixed properly on in concealed position all as directed by Engineer-in-Charge.

S&F in repairs Surface, hanging and wall mounted batten (Double side connection) suitable for LED tube 20/22 watts, 230 volts alongwith tube rod 22 watt (double side connection), including fixing mounting blocks 2 Nos, 15 mm MS conduit, 1.5 sqmm 3 core pvc insulated copper conductor cable complete . Make : Havells/ Bajaj/ Pyrotech/ Crompton

Supply and fix in repairs decorative recessed type LED light fitting 36 watt (size 2'x2') and including driver unit, including provision of 3 core copper flexible cable 1.5 Sqmm from ceiling rose to connector, including making addition/altn to existing false ceiling and providing of false ceiling sheets, aluminium frames including fixing arrangements complete etc complete all as specified and directed. Make : Havells/ Bajaj/ Pyrotech/ Crompton

Taking down existing earthing and in lieu M&L for new earthing complete with galvanised earth plate electode 600 x 600 x 6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level, connected to and including galvanised earth wire 4mm dia to the extent upto 7.5 metre as earth lead by means of bolts, nuts etc, with provision of charcoal and salt all as per electrical plate No 3 of SSR Part I, including water arrangement with GI pipe 20mm bore (medium grade), earth lead protection pipe 15mm bore light grade with bends, elbow etc. from earth plate to test point, excavation and earth work, returning, filling, ramming and removing of soil to a distance not exc 50 metre, making PCC 1:2:4 type B-1 pit (Earth chamber) with RCC 1:2:4 cover 50mm thick reinforced with XPM and testing on completion including making test point on wall as per SSR specifications all as specified and directed. Note: Cost of GI earth wire and protection pipe upto 7.5 metre shall also be deemed to be included in the quoted rate.

Taking Down Ceiling fans 1200/1400 mm sweep and Exhaust Fan any size transporting to store for safe custody for reuse or for depositing at the MES Yard complete all as specified and directed.

Fixing only ceiling fan 1200/1400 mm sweep and Exhaust Fan any size as obtained from taking down vide Ser No 128 herein before including painting of celing fan and Exhaust fan complete all as specified and directed.

S&F building Security light fitting 30 Watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements with braket of suitable dia and taking down old rusted bracket fittings complete all as specified and directed.

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.50 mtr depth for laying of underground cable, erection of poles etc. and getting out in soft/loose soil including separating serviceable/ cable cover for re-use at site obtained during excavation complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removal of surplus soil not exc 50mtr distance and depositing outside MD land complete all as specified and directed.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250mm x 150mm x 40mm laid in trenches complete all as specified and directed.

M & L for sand cushioning by spreading in trenches fine dry river sand by gently by punning down manually as in cable protection complete all as specified and directed.

M&L for cutting existing road/hard standing not exc 45x45 cm in wide & depth getting out excavated material for laying GI tube ;returning filling & well rammaing watering finish suraface 10 cm from top using PCC 1:3:6; including removal of surplase soil complete all as specified and directed.

S& F in replacement of GI pipe light grade 40 mm dia for laying in ground, along the pole in coping, road crossing etc for cabe protection including necessary fittings , clamps for supports, etc complete all as specified and directed.

S&F sheet metal enclosure TPN MCCB DB 4way, 415 V (vertical type) with bus bar double door type IP 43 - IK 09 with provision of MCCB 125 Amps (as incomer), fixed properly on / in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as specified & directed.

S&F MCCB 125 Amps, 4 Pole, 415V, 25KA complete all as specified and directed.

S & F MCB SPN 16-32 Amps, 240 / 415 Volts, 50 Hz, 10 KA Breaking capacity complete all as specified and directed.

M & L for 3 core 6 Sqmm PVC insulated wire armoured multistranded copper conductor cable including saddling in wall, cable duct with saddles & spacers connecting to LT panels, distrubtion board complete all as specified and directed.

Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables heavy duty with stranded aluminium conductor 1100 volts grade of 4 core 25 sqmm including saddling in wall, cable duct with lugs & spacers connecting to LT panels etc complete including taking down old unserviceable cable complete all as specified and directed. .

Supply & fix fans ceiling 230 V,1200 mm sweep complete all as specified and directed.

S&F metallic body exhaust fans AC single phase 230/ 240 V of size 300 mm sweep 900 RPM with louvers & shutters complete all as specified and directed. Note : A sum of Rs 28,800.00 towards sch of credit shall be deducted to arrive the contract sum.

sahajanand const co.

Joy builders