SBM 2.0 (FSTP)scheme Srimushnam TP Cuddalore DT

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

Earthwork excavation and refilling for pipeline works having bed width of 1.25m and below on linear measurement basis. (TWAD SOR 24-25 Pg.no:192)

Earthwork excavation in all soils and sub soils except hard rock requiring blasting with initial lead and lift including re-filling the sides of foundation in layer of 15 cm thick watering , ramming ,depositing the surplus earth in the premises as directed by departmental officers etc., complete as per standard specification.

Removal of Excavated Excess Earth away from the site to 2K.M including loading and transportation charges etc, complete as per standard specification. For 1M3

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers well rammed, watered and consolidated etc. complete complying with standard specification As per PWD SOR 2024-25 Pg no:29

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Supply delivery and Filling of Stone Dust in layer of not more than 15 cm thick including watering with all layers and consolidation complying with standard specification including cost and conveyance of sand at site and all labour charges and all other incidental charges etc. complete as per standard specification

Supplying and filling in Foundation with Sand Gravel Mix in the ratio of 1:1 with 0.685 Cum of sand and 0.667 Cum of Gravel in layers of not more than 15cm thick well rammed, watered and consolidated by using mechanical earth rammer etc. complete complying to standard specifications

Providing and laying of coarse aggregate size as below after washing & sieving to make it free from fines & dust. Passing through 50 mm & Retained on 40 mm sieve

Passing through 20 mm & Retained on 16 mm sieve

Passing through 10 mm & Retained on 6 mm sieve

River fine sand 1-2 mm

Providing and laying Porotherm Clay Blocks .The hollow blocks should be of the size 40 x 20 x 15 cms and the opening should be on both the ends

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Plain cement concrete 1:2:4 mix (One cement two sand and four aggregate) using 20mm ISS metal including mixing, laying, consolidating, curing cost and conveyanc of all materials to site and all labour charges etc., complete as per standard specification

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Providing centering for sides and soffits of R.C.C.works such as lintels, slab, beams and plain surface etc., complete excluding strutting upto 3.30 M height using mild steel sheet of size 90 c.m x 60 c.m and 10 gauge stifer with M.S. angles of size 25 mm x 25 mm x 3mm laid over silver w.c.wood joints of size 10 c.m. x 6 c.m. spaced at about 90 c.m. c/c and supported by casurina props of 10 c.m. to 13 c.m. dia spaced 75 c.m. centre to centre complying with as per standard specification.

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers

Providing and laying in position Standardised Concrete Mix M-30 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 400Kg/ cum and maximum water cement ratio of 0.45 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards.

Reinforced Cement concrete 1:1 1/2:3 (one cement one point five sand and three aggreedates ) mix using 20 mm ISS Gauge Hard granite broken stone jelly including cost and conveyance of all materials to site including labour charges for concrete mixing for laying , watering curing properly but excluding cost and labour for steel fabrication and centering form work etc, complying with standard specification and directed

Supplying, fabricating and placing in position TMT bars (Fe 500) for all RCC works as per design given including cost of steel and G.I. binding wire for placing at all depths of excavation, complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel, binding wire and for bar bending)

Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9" X 43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 20mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality with necessary welding and painting with one coat of zinc chromite primer and two coats of epoxy painting complete.(As per instruction of site engineer)as per standard specification etc., complete compying with standard specifications

30 x 30 cm manhole

Supplying and fixing in position best quality U.P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with U.P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications. 110mm UPVC Pipes

Providing and fixing uPVC pipes (Soil and waste line) of required diameter conforming to I.S.-13592, and I.S.- 4985 to withstand continous internal hydroulic pressure of 6 kg/cm2 including necessary fixtures and fittings, such as bends, tees, single junctions, double junctions and joining with rubber rings and lubricants, on wall by means of clips or in ground including necessary excavation, laying refilling, trench testing etc. complete. (Prior approval of sample and brand by Engineer in charge is necessary before use.) 6 inch UPVC Pipe

110mm UPVC Tee

110mm PVC Elbow

160mm UPVC Preforated Pipes

Supplying and fixing in position best quality HDPE soil/ waste pipes of various sizes having ISI mark and providing leakproof joints and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

Specials HDPE fittings and Butterfly valves

Lowering HDPE pipes and specials to trench and laying to proper grade and alignment and as directed by the department engineers (TWAD SOR 23- 24 Pg.no . 280)

Jointing HDPE Pipes and Specials by butt fusion welding / electro fusion welding joints using fusion equipment as per ISO 21307-2011 and as per IS 7634 (part-2) : 2012 including cost of hire charges for butt fusion equipment power supply arrangements etc., complete as per directed by Engineers. (TWAD SOR 23-24 Pg.no . 291)

Testing of pipes for water supply with hydraulic testing equipment by filling with water (including cost of water) and testing to recommended pressure in convenient stretches and attending the bursts if any occured during the test, excluding the cost of pipes but including other incidential and operational charges etc., complete for the following diametres of pipes.

Geophysical Investigation charges

Drilling of 150mm dia. Deep bore well in hard rock area including labour charges & transportation Charges

Supply & Delivery of 150mm dia P.V.C 6 kg/cm2 casing pipe etc

Supply and delivery of vertical wet type Three phase submersible pumpset (3 HP) discharging any of the following pumpage in lpm against noted head in m suitable for erection into the Bore well of 150mm dia with stainless steel shaft, bronze impeller and stainer with brass screws, water lubricated bearings with sand Guard.-with a duty of 50 lpm x 125M head. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pumpset should be provided with 3m length of suitable size PVC insulated copper flat cable connecting the pumpset & starter. The pumpset should conform to IS 8034/89 and as amended thereafter and bear ISI marking. etc., complete

Supply and delivery of 3 phase panel board- D.O.L. with two level and auto start as per standard specification PGNO 113

Supply and delivery of 4.00 sqm 3 core coppar flat cable including all materials and all labour charges etc

Supply and delivery of 32 mm UPVC pipe including all materials and all labour charges etc

Supply and delivery of PVC TANK including all materials and all labour charges etc 1000Liters As per IS 12701/1996

Errection of Submercible motar specials in the trench and laying to proper graed and alignment and as Technical officers

Supply and delivery of 40mm pvc pipe including all materials and all labour charges etc

Supply and delivery of 32mm GI pipe including all materials and all labour charges etc

Refilling excated Earth laying of pipes for Pipe Line trench 32 mm pv

Earthwork Excavation in all classes of soil consisting of Hard stiff clay including all labor charges for foundation as per SS20B etc complete.

Supplying of polished cuddapah slab of 20/30 mm thickness including laying to correct alignment as direct by engineer in charge. Includes fixing the slab to support structures.

Filler 10-12 mm

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement

Flooring with following plain ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing in position white Glazed European Water Closet of best qualityand approved make with 100mm 'P' os 'S' TRAP with Double flapped rigit P.V.C.seat cover withC.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings etc., complete complying with standard spoecifications, labor inclusive of fixing lowlevel flushing tank.

Dadooing with glassed tiles of 150mm*150mm*6mm size of approved quality and colour set in c.m 1:2 (one cement and two sand) 10 mm thick and pointing with white cement using 0.4 kg /m2 neatly as directed - including cost of all materials and labour charges etc complete as per SS

Suppling and fixing in position 15mm. Diameter brass/C.P screw down tap / pillar tap /swan neck tap (heavyduty) of approved make conforming to I.S. specifications and quality including cost of shellac, thread etc. complying with standard specifications and including cutting and threading wherever necessary

Supply and fixing of PVC solid Doors using 19gauge 19mm MS sq, tubes for styles and frames, 15mm MSsq. Tubes for to, Lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm x30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x30mm. the over all size of frames shall be 50mm x 45mm with suitable tabate for housing the shutter etc, complete as per standard specification

Supplying and fixing in position G.I union and flanges of heavy type of approved quality and good variety, of various sizes, including necessary cutting and threading of G.I.pipes for jointing the union and providing two coats of painting with good variety and approved quality of synthetic enamel paint over a coat of priming coat in case of pipe line above ground level and coat of tar in case of pipe line below groung level for both internal and external Water supply arrangements.

Supplying and fixing over the floors best quality of scratch ceramic tiles o 30 cm x 30 cm x 6mm size using cement mortor 1:3 mix mixed with 2% by weight of crude Oil and pointing with Cement Motor 1:3 mix Cost of all materials and Labour charges and bick jelly concrete etc, complete as per standard specifications.

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors including cost, conveyance of all materials, labour charges therefore etc complete

Wiring with 2X 1.5 sqmm (22/0.3) PVC insulated unsheathed SC.Cu.conductor of 1100v grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A F.T switch inflush with wall, covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light point etc complete SD-25

Supply and fixing of 20 W tube light fittings with copper choke and all other accessories etc., complete complying with standard specification.(S.D 89)

Supply and Fixing of bulk head (11W)fitting including all cost and conveyance etc.,complete

Supply , Fabrication and erection of Fabricated ducting made up of GI Sheet of 22 Gauge Thickness

Supplying and erecting , fabrication of Structural Steel work for roofing welded of bolted type using MS Channels angle, plates around bars etc, confirming to IS Specifications including Primer coating and enamel painting as per design given by the officers

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supply and fixing of ISA angle for tuss including cost of material conveyance of all mater, fabrication and fixing charges etc. complete as per ISI with rust preventive primer and ready to assemble condition for easy installation at site including dismantling making necessary with power drill to the accessories such as supplying and fixing holdfast, plastic brush inserts receiver runner buttom shock absorbers etc. complete as directed by departmental office

Fabricating, supplying and fixing of pre painted galvanium iron sheets with the following specifications. The materials should be PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be GI base pre painted hot dipped galvanised iron sheet and to be fixed with shelf tapping scres, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finsh should be terra cotta finish like malabar mangalore tiles. Finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the siste condition and as directed by the departmental officers

Fabricating, supplying and fixing of pre painted polycarbonate sheets with the following specifications. The materials should be PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be PC base pre painted hot dipped galvanised iron sheet and to be fixed with shelf tapping scres, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finsh should be terra cotta finish like malabar mangalore tiles. Finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the siste condition and as directed by the departmental officers

Supply and Installation of Danline ropes 20 to 30mm

Supply and installation of submersible centrifugal sewage non-clog pumps 3HP,15m head with10 Cubic Meter delivery per hour with Panel Board and all other fittings

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Supply and installation of submersible centrifugal sewage non-clog pumps 3HP,20m head with10 Cubic Meter delivery per hour with Panel Board and all other fittings

Supply and Installation of 30M Head, 60m3/hr Delivery,Submersible Cetrifugal Sludge cutter Non Clog Pump with starter, Panel board, MCB, Wire and all other fittings

Supply and installation of submersible centrifugal sewage non-clog pumps Pump - 5HP,15m head with 50 Cubic Meters delivery per hour with Panel Board and all other fittings(1 Working + 1 Standby)

Supply and fix fire hose (100mm) dia and female and male coupler stainless steel(304,202) gunmetal IS903 pressure 21kgf/cm2 including necessary fixtures and fittings, such as bends, tees, single junctions, double junctions and joining with rubber rings and lubricants, on the wall by means of clips or in the ground including

Providing and laying of cinder material

Supply and fixing of fancy glass shade and 11W for BH points

Provision for Highway crossing

V.JANARTHANAN (BID ID -1180620)