84815 SPECIAL REPAIRS TO INTERNAL AND EXTERNAL ROADS 16 QG , PG ROAD, STATION FAMILY CAMP, MM ROAD, STATION JCO MES, JONGA PL, SHIVNERI CAMP AND OTHER MISC AREA UNDER AGE CENTRAL OF GE NORTH PUNE

Amount

M&L for Repair to pot holes any depth, n exc 1 Sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in roads, paths etc. cutting around edges to at least 25mm in depth, making good by applying tack coat with bituminous primer @ 5 kg per 10 sq m, putting in premix as specified for thin bituminous carpet (2 cm thick) well rammed and sealed with premixed sand seal coat (6.8 kg of binder with 0.06 cum of sand), again well rammed (including supply of premix binder and sand) depth of potholes not exc 25 mm all as specified and directed.

Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exc 400 sqm, exc. 50mm and not exc. 100mm deep and removing same distance 50m and stacking whereas directed.

M & L for 7.5cm thick (compacted thickness) WBM, with coarse aggregates of granit or basalt grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size) , spread, rolled and consolidated to gradient and camber required.

All as per Ser item No. 3.00 above but except material complete all as specified and as directed.

M&L for preparing unsurfaced water bound macadam by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc and applying evenly a priming/tack coat with (paving bitumen) VG-10 at the rate of 7.50 Kg per 10 Sqm

M&L for preparation of black top surfaces by brushing with wire brushes for removing caked mud, existing layer of thermoplast paint etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags and compressor to remove all loose dirt etc, and apply evenly a priming / tack coat using paving bitiminous primer (VG-10 grade) @ 5Kg per 10 Sqm complete all as specified and directed.

M & L for premixed bituminous macadam with paving bitumen (VG-30 grade) using binder content 4% by weight of total mix (Job Mix) laid / rolled with 8 to 12 tonne power roller and compacted to required gradient and camber (consolidated thickness 50 mm) complete all as specified and as directed.

Applying evenly a priming/tack coat of VG-10 grade paving bitumenat the rate 2.5 Kg per 10 Sqm on BM surfaces complete all as specified and as directed.

M&L for providing bituminious premix hot mix asphaltic semi dense concrete (design mix) 30mm thick (consolidated) thickness with 5.5% binder content (paving bitumen VG-30 grade) by weight of total mix laid with mechanical paver rolled and compacted to required camber and gradient with 8 to 12 ton power roller complete all as specified and directed by Engineer In charge. (Note:- Laying shall be done by means of self propelled mechnical paver, finishing with suitable speed and capable of laying, spreading, tamping and finishing)

M&L for providing bituminious premix hot mix asphaltic semi dense concrete (design mix) 40mm thick (consolidated) thickness with 5.5% binder content (paving bitumen VG-30 grade) by weight of total mix laid with mechanical paver rolled and compacted to required camber and gradient with 8 to 12 ton power roller complete all as specified and directed by Engineer In charge. (Note:- Laying shall be done by means of self propelled mechnical paver, finishing with suitable speed and capable of laying, spreading, tamping and finishing)

M & L for preparation of exisiting bitumenous road/concrete surface and paving and marking road line, dashes (continuously / interrupted) arrow , letter 2.5 ± 0.5mm thick and not exc 10 cm wide using hot applied white/golden/yellow thermoplastic road marking paint with reflectory glass beads all as specified and directed.

M & L for preparation of exisiting bituminous road/concrete surface and paving and marking road line, dashes (continuously/ interrupted) arrow exc 10 cm in width using hot applied white/ golden / yellow thermoplastic road marking paint with reflectory glass beads all as specified and directed.

Supply and fixing retro reflective Mandatory/ Regulatory sign boards of 900 mm x 600 mm size with support length of 3750 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge

Supply and fix Precast Concrete curb stones of Size 450 x 300 x 100 mm thick using cement cocrete Mix (1:2:4) set and jointed in CM (1:4) including necessary excavation and eartwork and dismantling & removing of old curb stone from site etc all as specified and directed.

Supply and fixing metal tubular delineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermoplastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150mm x 150mm x 300mm) type B1 complete all as specified and directed.

Supply and fixing cat eye reflective type road stud of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and as directed.

Supply and fix solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. all as specified and directed.

S&F in repair solar delinator made out of polycarboate and toughened body of 80mm dia and delineated height 80mm comprise of super bright LEDs which gives 360 degree viewing solar panel 5 volt with visibility of 120m (approx), 3.7 Volt rechargeable battery of 1800 mAh with battery backup of 48 hours, also has a high intensity retro reflective band of 1" width for extra visibility. The delineator is mounted on MS pipe of height 1000mm and 50mm dia with an anti theft wire mesh provided over it for extra protection. Both the pipes and wire duly powder coated embedded in the ground with PCC 1:2:4 (300mmX300mmX300mm) including necessary excavation and earth work complete all as specified and directed.

Supply and fixing metal road stud reflective type out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermoplastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150 x 300mm) type B1 complete all as specified and directed.

Taking down old steel gate (area not exc 10 Sqm) repairing by welding / cutting steel members as required and refixing the same in the existing pillars / post complete all as specified and directed. (Note :- Steel members used if any will be paid in seperate item on supply only rate)

Supply only mild steel work for portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; and similar work conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

Surface dressing in hard & dense soil not exc 15 cm deep in soil and removing the material obtained to a distance exceeding 50 m but not exc 250 m where as directed.

M & L for 100 mm thick light wearing surface using moorum / red bajri including rolling and consolidation to a gardient and camber required.

Surface excavation not exc 30 CM deep and averaging 24 cm deep and getting out in Hard & dense soil complete all as specified and as directed.

Removing excavated material exc. 250 m but not exc. 500 m and depositing where directed complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in sub base / flooring complete all as specified and as directed.

Material and labour for hardcore broken stone or boulders of gauge not exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand etc all as specified

Aadarsh Construction

MOHANLAL MATHRANI CONS. PVT. LTD.

THE SAIRAM CONSTRUCTIONS