Modification of hut type shed no. 4 by increasing the height at Aliganj, Lucknow Workshop

Amount

Dismantling corrugated iron & asbastas roof sheet and stacking of materials as directed by Enggin- charge within a distance of 60 mtrs. (Existing Shed)

Dismantling of griders, trusses and other steel works including stcking of materials as directed by Engg-in-charge within a distance of 60 mtrs.

Shed Column- ISMB-300

20mm thick MS Plate(0.50mx0.50m)

65x65x6 Angle Column Support)

16mm thick MS Plate(0.30mx0.30m)

Truss 75x75x6 Angle

Struts 65x65x6 Angle

ISMC-150 Beam

H.S. 70x50 4mm thick Purlins

Excavation in foundation in ordinary soil (Loam Clay or Sand) including lift upto 1.5m and lead upto 30m and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of the foundation work. (Shed Columns)

Concrete with 4cm gauge I class brick ballast, coarse sand and cement in proportion of 12:6:1 in foundations and under floors including supply of all materials, labour and tools and plants etc. required for proper completion. (Shed Columns)

Cement concrete with 2cm gauge approved hard stone ballast, coarse sand and cement in proportion of 4:2:1 including supply of all materials, labour,side shuttering if required and T&P etc. required for proper completion of work (Shed Columns)

Supply of 25 mm dia.M.S. Anchor bolts (conforming to IS-226) 500 mm long with base plate(50x50x6 mm)welded with anchor bolts,including its threading upto a length of 10cm. and galvanizing upto 15cm from top, also supply of a pair of galvanized standard nuts with threading including supply of 5mm thick washer and cost of labour material and T&P etc. required for proper completion of the work

Fixing and grouting 25 mm and below dia M.S. Anchor bolt in proper alignment level and setout with the help of a template including supply of all labour T&P etc. reqd. for proper completion of the work. (labour rates only)

Mild Steel or Iron work in heavy sizes such as trusses built up gates, door frames, record, racks roof work gates etc. wrought to required form including holes rivetting or welding where necessary and also fixing in proper position and alignment including cost of all materials supplied by contractor

Shed Column- ISMB-250

20mm thick MS Plate(0.50mx0.50m)

65x65x6 Angle Column Support)

16mm thick MS Plate(0.30mx0.30m)

Truss 65x65x6 Angle

Struts 65x65x6 Angle

ISMC-150 Beam

H.S. 70x50 4mm thick Purlins

Providing and fixing precoated galvanised iron profile sheets in roof (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Painting or varnishing new iron work in small areas or new wood work with one coat of ready mixed priming paint and one coat of approved superior quality ready mix paint "Luxol" or equivalent brand or varnish including supply of all materials, labour and T&P etc. required for proper completion of the work. Paint to be used should conform to the I.S. 103-1950 (@ 35% of Shed covered area)

R.D. ENTERPRISES