Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Status |
|---|---|---|
| 1 | Admitted-Fee/PreQual/Technical/Finance | Admitted-Fee/PreQual/Technical/Finance |
| 2 | Admitted-Fee/PreQual/Technical/Finance | Admitted-Fee/PreQual/Technical/Finance |
Tender Value
Refer Docs
EMD Value
₹1,890
Closing Date
6 Jun 2022, 4:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Ex Engineer
Ex Eng MID Ang HQ awantipora
Repair works to 250mm Dia Pump deliveries and 400 mm Dia Rising Main at LIS Khudpora Stage 2nd
2022_IFC_171387_12
18/MIDA of 2022-23
Open Tender
Machineries/ Mechanical Engg Items
Item Rate
6 days
Khudpora
Repair works to 250mm Dia Pump deliveries and 400 mm Dia Rising Main at LIS Khudpora Stage 2nd
2 documents required · 2 mandatory
₹100
Yes
Ex Engineer Mechanical irrigation Division Ang H
₹1,890
Yes
7 Jun 2022
30 May 2022
7 Jun 2022
30 May 2022
6 Jun 2022
30 May 2022
90 days
Amount
Repair works to damaged joints of 400 mm NRV installed outside pump house. The job includes dismantling of NRV by removing/cutting of bolts and nuts and welded flanged joint using necessary tools and taclkles (Tripod etc). Cleaning of joints and Providing and fitting of high pressure gasket to joints of required size. The job also includes providing and fitting of new M S bolts and nuts to the joints. The joints shall be tested on full load. The required earth work for facilitating the smooth execution of work shall be in contractors scope
1. Repairs/welding of damaged 400mm diameter Rising main by way of following: • Chipping the old damaged welding from the joint by proper means. • Clean the joint and bevel it properly by grinder to facilitate space for the welding after removing all the burrs using wire brush and irregularities of the previous welding. • Align and then Weld the joint; first do one run root welding circumferentially between the beveled areas. • Remove all slag and deposits before second run by hammering using chipping hammer. The weld surface shall be smoothened by the grinder. • After completion of second run of welding, the surface needs to be cleaned and smoothened once again so that the cut strip is placed properly and firmly on the joint. 2. For strengthening of the joint, the job includes Jacketing of the above welded joint as below: • Providing/fitting of 6 inch M S strip of 8 mm thickness over the joint. The cut strips shall be firmly placed/enveloped and welded over the joint for extra strengthening. The strip shall be welded to the pipe using two runs on each side. The required earth work for facilitating the smooth execution of work shall be in contractors scope.
Repairs/welding of damaged 200mm diameter Pump Deliveries by way of following: Dismantling/Cutting of existing damaged Flanged joint by using gas cutting. Clean the joint and bevel it properly by grinder to facilitate space for the welding after removing all the burrs using wire brush and irregularities. • Align and then Weld the joint; first do one run root welding circumferentially between the beveled areas. • Remove all slag and deposits before second run by hammering using chipping hammer. The weld surface shall be smoothened by the grinder. • After completion of second run of welding, the surface needs to be cleaned and smoothened once again so that the cut strip is placed properly and firmly on the joint. 2. For strengthening of the joint, the job includes Jacketing of the above welded joint as below: • Providing/fitting of 6 inch M S strip of 8 mm thickness over the joint. The cut strips shall be firmly placed/enveloped and welded over the joint for extra strengthening. The strip shall be welded to the pipe using two runs on each side. The required earth work for facilitating the smooth execution of work shall be in contractors scope. • Joints to be tested on full load. All tools and tackles including welding machine, grinder and gas cutter are to be arranged by the firm and all consumable items shall be in contractor’s scope. It is pertinent to mention that the firm has to arrange its own DG set to execute the work and shall be in contractor’s scope. The contractor is supposed to execute the job through a high skilled welder.
M/s Shaheen Enterprises
stage.html
html • 0.02 MB
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .