Special repair of hostel Building for Regional Health and Family Welfare Training Centre at Rohtak Re-invited

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing. (b) In cement. (HSR 8.5 (b)

Dismantling white or coloured glazed tiles (to be carefylly removed). (HSR 8.38)

Providing & laying 80mm thick ISI marked interlocking paver Blocks conforming to IS 15658:2006 / IRC SP 63-2004 of all shapes and colours in design mix cement M-40 over a bed of 30mm thick fine sand complete in all respect. (HSR 10.159)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level. (HSR 11.7)

Terracing consisting of tiles 22.86cm x 11.43cm x 3.81cm, laid over 87.50mm mud filling on a layer of 25mm mud plaster and another layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg per Sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (a) 100mm dia PVC pipe 6 kg. pressure (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. (HSR 13.89 (a) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & fixing Vitrified Tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note: - Tile shall be premium quality (1st quality) of reputed manufacturer like NITCO, KAJARIA & RAK. (HSR 14.89) Note:- The Agency to whom the work is allotted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & fixing Vitrified Tiles of size 600 x 600mm of approved make in skirting/ dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note: - Tile shall be premium quality (1st quality) of reputed manufacturer like NITCO, KAJARIA & RAK. (HSR 14.90) Note:- The Agency to whom the work is allotted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

12mm thick cement plaster 1:6. (HSR 15.7)

15mm thick cement plaster 1:6 on the rough side of single of half brick wall. (HSR 15.12)

Plastering on under side of ceiling 10mm thick cement plaster 1:4. (HSR 15.52)

Painting two coats with synthetic enamel Paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.5)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (b) 1st Quality. (HSR 16.79 (b)

Cost of aluminium fitting complte for doors and windows, such as tower bolts, handles, etc., and screws for these fittings (excluding sliding bolt). (b) For double leaf shutter. (HSR 17.72 (b)

Factory manufactured panelled door or glazed window shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to IS specification No. 1003, kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail, 200mm wide bottom rail and 100mm wide other rails, with panels of 15 mm thick , tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (a) 30mm thick. (HSR 17.90 (a) - Note 17.18 i)

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to IS specification No. 1003, kiln seasoned) with 100mm wide vertical styles 150mm wide lock rail 200mm wide bottom rail and wire gauze of 140G or 120G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (styler and rails of windows shutters shall be 75mm wide). (a) 30mm thick. (HSR 17.92 (a) - Note 17.18 i)

Supplying and fixing glass panes including special metal sash putty of approved make. (b) Glass panes 4mm thick, exceeding 40sq dm areas. (HSR 18.30 (b)

Pressed steel sheet frames (chowkats), consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete:- (b) door and window frame of size 76mm x 38mm with 35mm wide single rebate. (HSR 18.34 (b)

NS items

Providing and laying 200 mm thick granular sub base consisting of drainage layer confirming to Table 400.1 Grading –VI of MORT&H 5th edition, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve desired density complete as per clause No.401 of MORT&H specifications for road & bridge (5th Revision) of 2013. (NS).

P.H. work

Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type Orissa or Orya water closet suite for Sinking into floor, with raised foot treads complete with 100mm H.C.I, ‘P’ Trap with or without vent as required and all other necessary fittings as fully described in item no.30.1 above. (a) Size 580mm. (i) White. (HSR 30.2 (a) (i)

Providing and fixing in position best Indian make (as approved by the Engineer-in-charge) European type water closet suite, Syphonic type, Consisting of- (i) Vitreous chinaware Syphonic Suite with 15 litres capacity matching chinaware cistern and all internal brass fittings complete with ‘P’ or ‘S’ trap with or without vent; (as approved by the Engineer-in-charge). (ii) One piece Seat and Lid in Hollow black or White plastic fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) complete in all respects including cutting and making good the walls and floors. (a) Single trap symphonic W.C. Suite. (i) White. (HSR 30.5 (a) (i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF THREE URINALS FLAT BACK OR ANGULAR LIPPED FRONT IN VITREOUS CHINA-WARE WITH 10 LITRES CAPACITY BEST INDIAN MAKE C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE ETC., COMPLETE AS FULLY DESCRIBED IN ITEM NO. 30.19 ABOVE. 465 mm high. (i) White. (HSR 30.21 (i)

Providing and fixing in position Indian make (Ordinary) Lavatory Suites Consisting of Lavatory in Vitreous China Ware size as given Below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary; R.S or C.I Brackets for building into wall including Painting; 32mm C.P Brass Waster with C.P brass chain and rubber plug; 15mm C.P Brass Screw down pillar tap with Jamnuts or couplings best design (as approved by the Engineer- In-charge). All fittings best Indian make and to the approval of the Engineer-in-charge. ALL brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fittings etc. (a) White. (iv) Size 550 mm x 400 mm with one no. Tap. (HSR 30.41 (a) (iv)

PROVIDING AND FIXING IN POSITION OF BEST QUALITY STAINLESS STEEL SINK WITH COMPLETE FITTINGS AS FULLY DESCRIBED IN ITEM NO. 30.51 ABOVE. (a) 600 mm x 450 mm x 200 mm. (HSR 30.53 (a)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER WITH 15 OR 20 I/D INLET. (a) VITREOUS CHINA WARE ROSE SHOWERS. White (i) 175mm diameter. (HSR 30.66 (a) (i)

Providing and fixing in position 15mm i/d C.P brass bib Cocks of best quality (as required by the Engineer-in-charge). (a) Bib cock long body. (HSR 30.75 (a)

Bib cock.

Providing and fixing HDPE Water Storage Tanks of Sintex, Diplast, O.K. supreme make with covers/ lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respect to the satisfaction of Engineer-in-Charge. (except civil work). (e) 1000 Ltr. Capacity. (HSR 30.119 (e)

Providing & fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal Work - Exposed on Wall. (DSR 18.10) (a) 15mm internal diameter of pipeline.

PH NS items

Providing & fixing of PVC connection 18" complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of PVC Cistern 10Ltr. Capacity complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of 15mm dia angle valve complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of waste pipe "PVC" complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of Pillar cock "BKC make" complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Providing & fixing of waste jali complete in all respect as per approval of the Engineer-in-charge of the work. (NS)

Recovery items: - Bidders have to quote rates for recovery items at least or more than reserve price. The rate quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of structure have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) on approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. The reserve price is as under: -

Tile work @ Rs.3000/- per 1000 nos.

Brick bats @ Rs.500/- cum

Note: - All quantities of the above materials have been worked out on the basis of theoretical quantities. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.

SM CONSTRUCTION

Nathu Singh

PARVEEN CONTRACTOR

Amit Malik Contractor