SPECIAL REPAIR OF BLDG NO T-89 OF 167 MED REGT AT BMC UNDER GE (C) KOLKATA

Amount

Dismantling of AC (corrugated, semi corrugated) sheet in roof covering incl ridges complete all as specified and directed

Dismantling wall and ceiling board (fibre, pulp, insulation) any thickness incl cover fillet complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

Demolition of brick work or stone masonary built in cement mortar including all quions & jambs etc complete all as specified and directed

Taking down cement plaster of any description on brick work or stone masonary wall including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes n.exc 1.5 sqm each complete all as specified and directed

All as per item No 06 here-in-before but size exc 1.5 sqm and n.exc 4.0 sqm each

Demolition of cement concrete (Un-reinforced) in ground floor and paving n.exc 15cm thick above or below ground level complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

Taking up or down steel tubing 15mm dia and connection of 15mm bore complete all as specified and directed

All as per item No 11 here-in-before but 20mm dia bore

S&F of pre-painted galvalume aluminium zinc coating GI based corrugated / semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screw complete all as specified and directed

S&F of Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, fixed with self tapping screw complete all as specified and directed

S&F of 4mm thick suspended false ceiling HPSC (high pressure steam curved) pre-primered fibre cement non asbestous building board similar to E-Board Classic placed in snap grid of size 605x605mm with powder coated aluminium angle/channel/tee section duly suspended with 4mm dia GI hanger fixed with GI hooks 4mm dia and fastner as required at the site including two coat of oil bound distemper complete all as specified and directed.

M&L for rolled mild steel work in tubular/hollow as in trusses, purlin, rafter etc conforming to IS-4923 grade YSt.-240 complete all as specified and directed

M&L for rolled mild steel sections as in main and cross beams, hip and jack rafters; wind tie; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe-290 (Gde E-165) complete all as specified and directed

M&L for rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-290 (Gde E-165) complete all as specified and directed

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut of 11 to 15mm dia, and 22.50 to 30.00 cm long complete all as specified and directed

M&L for fly ash bricks using old size bricks (conforming to IS :13757) straigth or curved on plan exc 6m mean radius built in CM 1:6 cmplete all as specified and directed.

All as item No. 20 here-in-before but half brick thick brickwork built in CM 1:4 complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces in two layers (10mm + 5mm) and using water proofing compound in top layer as per manufacturer instruction, finishing the surfaces even and fair without using extra cement complete all as specified and directed

M&L for rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces even & smoth without using extra cement complete all as specified and directed

M&L for rendering 5mm thick in CM (1:3) as in ceiling surfaces even & smoth without using extra cement complete all as specified and directed Note:- WPC will be measured and paid separately as supply only.

Supply only liquid water proffing compound as required

S&F of Welded steel wire fabric weight not more than 4Kg/Sqm fitted by MS nails complete all as specified and directed

M&L for Pressed steel frames for doors with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (anealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for RCC (Nominal Mix) 1:2:4 type B-1 (Using 20mm graded stone aggreagate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for RCC (Nominal Mix) 1:2:4 type B-1 (Using 20mm graded stone aggreagate) as in slab, shelves, Chajja supported on walls beam & coloumns in floor roof including balconies, canopies, deck slabs & shelves complete all as specified and directed.

M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs,floor,slabs,landings, chajja and similar work not exceeding 200mm thick for rough finished surfaces (Horizontal or slooping )

M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunch- ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces complete all as specified and directed

M&L for PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in bed blocks/hold fast complete all as specified and directed

S&F of 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed

S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed.

S&F of Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

M&L for 1.50mm thick power coated aluminium , three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc.Complete all as specified and as directed. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall deemed to be included in quoted rate. Only measure opening size of window incl 5mm thick tinted glass and SS wire cloth.

S&F of powder coated aluminium ventilators with louvers and glazing including frame of section over all size of window 600X450mm complete with following specification:- (a) Alu frames of size 45x45x1.5mm (b) Rail & Stile 45x45x1.5mm thick (c) 4.80mm thick frosted sheet glass

M&L for drapery rod made of electric resistance welded MS pipe of 21mm dia having a coating of corrugated virgin PVC extrusion and cover with ABS plastic complete all as specified and directed.

S&F of end finials for drapery rod and including closed type stainless steel all brackets fixed on wall complete all as specified and directed.

S&F of 100mm Butt hinges, extruded brass, with brass hinge pin, bright polished, complete all as specified and directed

S&F of Aluminium anodised, barrel tower bolts of extruded section 200mm long complete all as specified and directed

S&F of Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy of 300mm long complete all as specified and directed

S&F of Extruded aluminium alloy handles, fabricated type, anodised 150mm long complete all as specified and directed

S&F of Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, 150mm long complete all as specified and directed

M&L for 18/19 mm thick Medium density fibre board, exterior grade, fixed to timber framework with screws complete all as specified and directed.

S&F of 30mm width of flaps Continous (Piano) hinges, brass, bright finish or electrogalvanised complete all as specified and directed..

S&F of 40mm dia cupboard knobs fixed with nut screws and washer of wooden finish brass polished complete all as specified and directed.

S&F of Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L for 75mm thick PCC (1:4:8) type D-2 (Using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified.

M&L for joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

All as item No. 53 here-in-before but in skirting with and including 10mm thick rendering on fair faces of brickwork in CM 1:4 complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L for glazed ceramic coloured tiles 450x300x6-7mm in vertical surfaces set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed

M&L for granite slab 15 to 20mm thick of any type work table rubbed and polished in kitchen platforms and like over and including cement screed bed 15mm thick in CM (1:6) bedded and jointed with grey cement slurry and pointed with white cement mortar (1:2) using marble dust with admixture to match with shade of granite complete all as specified and directed

S&F of 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

All as per item No 58 here-in-before but for 25mm outer diameter CPVC pipes

Cutting chase, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for conceled water pipe etc. and making good cutting not exc 10Cm girth complete all as specified and directed..

S&F of Vitreous China wash down water closet pan including P or S trap (pedestal pattern), white (excluding flushing cistern and flush pipe) including plastic water closet seat, black colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device and wash down water closet complete all as specified and as directed as in repair.

S&F of vitreous china squatting pan orrissa pattern size 580x440mm white with intregal foot rest including connection to trap, and flusing pipe, anti-syphonage pipe, etc and including lime concrete bedding complete all as specified as in repair .

S&F of vitreous china wash hand basin white counter sunk of size 550 x 400mm excluding taps but including 32mm PTMT waste coupling (excluding 32mm waste pipe) complete all as specified and directed as in repair.

S & F of 32mm bore PVC waste pipe flexible type including all cups and sockets with minimum length 800mm for any type/make/size for wash hand basins complete all as specified and directed in repair.

S&F of half stall urinal with 40mm PTMT waste coupling and PTMT spreader (excluding 32mm waste pipe)complete all as specified and directed as in repair

S&F of PVC flusing cistern low level 10 Ltr capacity of approved make including fixing of brackets connection to WC with CI brackets and making good disturbed area complete all as directed.

S&F of 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall complete all as specified and directed as in repair.

All as per item No. 67 here-in-before but double socketed complete all as specified and directed.

S&F of PVC (SWR) bend any radius 110mm bore complete all as specified and directed as in repair

S&F of PVC (SWR) junction single (single T) equal or unequal 110mm bore complete all as specified and directed as in repair .

M&L for diameter of outlet 75mm UPVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed as in repair

S & F of 15mm bore brass chromium plated Angular Valve with Wall Flange complete all as specified and directed as in repair .

S & F of brass chromium plated Fancy Type Bib taps for 15 mm bore pipe complete all as specified and directed as in repair .

S & F of for brass chromium plated Pillar Tap (Fancy Type) screwed for 15 mm bore pipe complete all as specified and directed as in repair

S & F of 600mm long Towel Rail chromium plated 20mm dia fixed with screw complete all as specified and directed as in repair

S&F of PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and directed

S&F of triple layer PVC water storage tank cylinderical, verticle with closed top hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm outer diameter for CPVC pipe & making connection for inlet and outlet including dismental of old water tank and removing from site. complete all as specified & directed.

M&L for complete removal of existing treatment and preparing old surfaces and applying 2 coats of oil emulsion distemper over a coat of primer including 3mm thick putty complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying 2 coats of oil emulsion distemper over a coat of primer including 3mm thick putty complete all as specified and directed.

M&L for complete removal of old decorated surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: old work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L for preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L for preparation of new surfaces of wood and wood based materials of any descriptions not otherwise described over 10Cm width or girth & applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of old surfaces of steel or steel based materials of any descriptionand applying one coat of synthetic enamel paint over 10 Cm width or girth complete all as specified.

M&L for preparation of new surfaces of steel and steel based materials of any descriptions not otherwise described over 10Cm width or girth & applying two coats of synthetic enamel paint complete all as specified and directed

Taking down carefully unserviceable copper/ aluminium point wiring (light, fan, buzzer, socket or power) including all fittings such as switches, socket, ceilling roses, regulators and fittings complete and making good the disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for Point wiring (Concealed type) complete with FRLSH PVC insulated, unsheathed, stranded copper conductor of nominal area 1.5 sqmm, 1100 volts grade, along with one single run of same size and type of copper wire continuous earth wire to common earth dolly in and including cutting / chasing on brick wall not exceeding 10cm grith (excluding ceiling surface for existing pipe) and supply and fixing PVC conduit pipe medium grade of nominal size 20mm dia along with connected fittings / junction boxes using existing sunk terminal boxes, new 3mm thick laminated sheet cover with brass screws and cup washers with all accessories and making good disturbed surface with cement morter ratio of 1:3 and treated surface with existing white / colour wash, oil bound or cement base paint etc to match with existing surface complete all as specified and directed by the Engineer-in-Charge.

All as per item No 87 here-in-before but One 3 pin 5 amp socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-Charge.

All as per item No 87 here-in-before but one 3 pin 5A switch socket outlet on independent board with other switch complete all as specified and directed by Engineer-in-Charge.

All as per item No 87 here-in-before but using 2.5 sqmm size stranded copper conductor cable for one 16 Amp switch socket outlet point on independent board complete PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 87 here-in-before but using 4.0 sqmm size stranded copper conductor cable for one 16 Amp switch socket outlet point on independent board including 4.0 Sqmm multistrand PVC insulated and unsheathed copper conductor to common earth and connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

S & F of switch piano flush type, single pole, one way, 5A complete all as specified and directed. Make:- Panasonic / Anchor / Havells

S&F of switch socket combination multipurpose 3 pin, 15 Amps and 5Acontrolled by one switch complete all as specified and directed. Make:- Panasonic / Anchor / Havells

S & F of socket outlet 5 pin, 6A, 230 Volt flush type on same board complete all as specified and directed. Make:- Panasonic / Anchor / Havells

S & F of ceiling rose, PVC / Polycarbonate, 65 x 50 mm, three terminals complete all as specified and directed. Make:- Panasonic / Anchor / Havells

S & F of ceiling fan regulator electronic step type, solid state, 240 volts complete all as specified and directed. Make:- Panasonic / Anchor / Havells

S & F of switch socket combination 2 in 1, 3 pin switch socket outlet on independent board complete all as specified and directed by Engineer-in-Charge. Make:- Anchor Cat No 14111 & 14119 / Legrand Cat No 677225 or equivalent model of Havells / Plaza / Cona.

S&F of energy efficient LED fittings of capacity 20 W suspended type /wall mounted type complete with LED tube lamp and fitting with copper flexible PVC cable of 0.50 Sqmm twin core not more than one metre in length complete all as specified and directed. Make:- Crompton Cat No LDL-20WW / Havells Cat No - ENDURALINEARNEOBS20WLED865SPCWH / Bajaj Cat No - BRTX 20W LED 4F WH or equivalent model of Philips

S & F of energy efficient LED fittings of capacity 10 W complete with LED tube lamp with copper flexible PVC cable of 0.50 Sqmm twin core not more than one mtr in length complete all as specified and directed. Make:- Crompton Cat No LDL-10WW / Havells Cat No - ENDURALINEARNEOBS10WLED830SPCWH / Bajaj Cat No - BCLSB 10 WH or equivalent model of Philips

S&F of LED fittings with lamps of 30 watts for bldg security light IP 66 power coated pressure die cast aluminium compact high power LED street light with compact size & rough design 32mm GI Bend complete all as specified and directed. Make:- Crompton Cat No - LST-30-CDL-M, Bajaj Cat No - BCLST 30W LED / Havells Cat No ENDURACITYLITEPLATPLUSSL30WLED757SASYBOPC

Taking down unserviceable rusted / damaged MCB DBs of any type and way along with any type MCB and keeping serviceable MCB in safe custody for re-use in the work and making good to the disturbed surfaces of walls etc complete all as specified and directed.

S&F of MCB DB made up with sheet metal double doo, 12 way single pole and neutral double door with 200 amps rated bus bar, including connection complete all as specified. Make:- L&T cat part No DBSPN012DD / Legrand Cat No 507602 or equivalent model of ABB / C&S Electric Ltd

S&F of MCB TPN DB made up with sheet metal, phosphorised, power coated, neutral link, earth bar and din rail, 8 way TPN with 200 amps rated bus bar, 415 volts complete all as specified and directed Make:- L&T cat part No DBTPE008DD / Legrand Cat No 507662 or equivalent model of ABB/ C&S Electric Ltd

S&F of MCB 6 to 32 Amps, SP, 240 Volts, C-curve breaking capacity 10 KA complete all as specified and directed by Engineer-in-Charge. Make:- Legrand cat part No 408595, L&T cat part No BB10060C to BB10320C or equivalent model of Hager / Siemens / ABB / Schneider.

S&F of MCB 6 to 32 Amps, DP, 240 Volts, C-curve breaking capacity 10 KA complete all as specified and directed by Engineer-in-Charge.. Make:- Legrand cat part No 408617, L&T cat part No BB40630C to BB20320C or equivalent model of Hager / Siemens / ABB / Schneider.

S&F of TP 63 Amps, 415 volts, MCB C-curve breaking capacity 10 KA as directed by Engineer-in-Charge. Make:- Legrand Cat Part No - 408683 or L&T Cat part No : BB408683C or equivalent model of Hager / Siemens / ABB / Schneider.

S&F of sub main wiring with two run of single core PVC insulated & unsheathed stranded copper conductor of size 4.0 Sqmm along & one run of PVC insulated & unsheathed stranded copper conductor of size 4.0 Sqmm as earth lead drawing into rigid non metalic PVC conduit of size 20mm dia including taking down old unserviceable complete all as specified and directed Note:- Two run of 4 Sqmm cable and one run of 4.0 sqmm cable will be measured as single length all as directed by Engineer-in-Charge.

All as per item No 107 here-in-before but with two run of single core 6.0 Sqmm and run of 6.0 Sqmm cable complete all as directed by Engineer-in-Charge

M&L for Earthing complete with GI pipe electrode, 40mm bore, medium grade, 2.5m length buried directly in ground vertically with top edge not less than 1.25m below ground level, connected with earthing lead of 4mm dia galvamised iron steel wire by means of boths, nuts, check nuts and washeres protected by 20mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350 x 350 x 50mm reinforced with 8mm dia TMT steel bars @ 15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers, necessary earth work in soft / loose soil as shown in ELectrical Plate No 4 of MES Schedule Part I and testing complete including taking down old one complete all as specified and directed

S&F of power supply unit consisting of starter with 11-18 Amp over load protection, MCB of 25A with socket complete for AC 240V single phase including taking down old U/S one complete all as specified and directed by Engineer-in-Charge Make:- North West Cat No PU3M-FT / Havells Cat No - AHOO323204 or equivalent model of Siemens / ABB / Schneider

Taking down and opening out the ceiling fan / wall mounted fan upto 1400 mm sweep for inspection, removing bush / bearing, cleaning of bush / bearing, replacement of unserviceable / worn out bearing / bush, shaft, removing burnt out coils from the slots, cleaning and repairing of slots complete including materials like split pin, rubber reel etc , reassembling spray painting and refixing of fan complete including any hook required for fixing fan and incl 1.5 mtr length connecting rod with painting of ceiling fan / wall fan / exhaust fan of any size and sweep complete with synthetic enamel paint by spraying including filling with cavities with filler, after cleaning all dust etc complete all as specified and directed

S&F of wall mounted fan complete 230V, RPM 2100, Sweep 400mm complete all as specified and directed. Make:- Havells , CG, Philips, Orient

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs 1,28,581.00 mentioned on Page No 37 shall be deducted from the total quoted amount of BOQ.

BHARUKA ENTERPRISES

PINKY CO.

Shree Mahabir Builders

Tirupati Buildcon Pvt. Ltd.