Construction of WRPC Office and Guest House and External Development Work at F-3, MIDC Area, Marol, Opp. SEEPZ, Central Road, Andheri (East), Mumbai

NAME OF WORK: “CONSTRUCTION OF WRPC MAIN OFFICE BUILDING (S+M+7) & GUEST HOUSE BUILDING

(LG+UG+2) LOCATED AT MIDC, ANDHERI (EAST), MUMBAI MAHARASHTRA ALONGWITH ASSOCIATED

STRUCTURES BUILDINGS INCLUDING DEMOLITION OF EXISTING BUILDINGS”

GRAND SUMMARY OF COSTS

S. NO. DESCRIPTION OF HEAD OF WORK DSR ITEMS NON SCHEDULED TOTAL AMOUNT

S. NO. DESCRIPTION OF HEAD OF WORK DSR ITEMS NON SCHEDULED TOTAL AMOUNT

2022/2023 ITEMS (Rs.)

TOTAL AMOUNT WITH CORRECTION FACTOR

TOTAL AMOUNT WITH CORRECTION FACTOR

9 HVAC SYSTEM - WATER COOLED CHILLER ₹ 30,53,536.00 ₹ 1,93,39,686.00 ₹ 2,23,93,222.00

11 EXTERNAL ELECTRIFICATION WORK ₹ - ₹ 2,50,16,149.00 ₹ 2,50,16,149.00

TOTAL AMOUNT WITH CORRECTION FACTOR

TOTAL AMOUNT WITH CORRECTION FACTOR

08.08.2024 AND GST FACTOR 1.0633 FOR GST

Digitally signed by VARUN

NAME OF WORK: “CONSTRUCTION OF WRPC MAIN OFFICE BUILDING (S+M+7) & GUEST HOUSE BUILDING (LG+UG+2)

LOCATED AT MIDC, ANDHERI (EAST), MUMBAI MAHARASHTRA ALONGWITH ASSOCIATED STRUCTURES BUILDINGS

INCLUDING DEMOLITION OF EXISTING BUILDINGS”

OFFICE & GUEST HOUSE BUILDINGS

SUMMARY OF COST OF CIVIL WORKS

S. No. Chapter Description/ Head of work Scheduled Items Non Scheduled TOTAL

based on DSR-2023 Items (Rs.)

1 Dismentaling & Demolition Work - -12,00,000.00 -12,00,000.00

2 Carriage of Materials 3,18,074.00 - 3,18,074.00

5 Reinforced Cement Concrete 18,02,70,943.00 - 18,02,70,943.00

14 Exterior Finish (Façade) Work 18,63,451.00 3,91,02,849.00 4,09,66,300.00

16 Landscaping & Horticulture Work 69,80,258.00 - 69,80,258.00

TOTAL OF CIVIL WORKS CARRIED OVER

TO GRAND SUMMARY OF COSTS

GRAND TOTAL 31,89,99,768.00

GRAND TOTAL 31,89,99,768.00

NBCC (India) Limited CIVIL WORKS 2

Digitally signed by VARUN

NAME OF WORK: “CONSTRUCTION OF WRPC MAIN OFFICE BUILDING (S+M+7) & GUEST HOUSE BUILDING (LG+UG+2) LOCATED AT MIDC,

ANDHERI (EAST), MUMBAI MAHARASHTRA ALONGWITH ASSOCIATED STRUCTURES BUILDINGS INCLUDING DEMOLITION OF EXISTING

OFFICE & GUEST HOUSE BUILDINGS

SCHEDULE OF QUANTITIES

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

SH-15: SH DISMANTLING AND DEMOLISHING (ALL 03 NOS. OF EXISTING BUILDINGS)

Dismantaling and Demolishing work of existing buildings manually/ by mechanical means and Disposal of building

rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading,

transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge for all leads

including all lifts involved.

Before starting the demolition or construction activity at site, the Contractor shall erect hard barricading (trapezoidal

profiled Zincalume/ Galvalume sheeting with necessary structural steel erection) or as per norms of the concerned

governing body of the Government, whichever is higher, hard barricading all around the plot leaving one entrance and

exit with gates. Barricading item shall not be paid separately.

During execution, if any sheets gets damaged, shall be replaced immediately with the new sheets till completion of the

work and handed over. The quoted rates shall be inclusive of all associated civil works like earthwork, concrete work,

RCC work, formwork, reinforcement etc. The barricading must be designed to withstand the maximum windspeed at the

area. The design should be got proof checked by NIT/IIT and report to be submitted by the contractor. Nothing extra

shall be paid for this purpose

The bidder shall quote his net price after adjustment of value of serviceable materials of the buildings and the cost of

disposal of unserviceable material on dumping yard approved by local authorities and as per the norms/ rules and

regulations of National Green Tribunal (NGT)

Obtaining permission from local body for disposal of building rubbish / malba / similar unserviceable, dismantled or

waste materials to approved municipal dumping ground is included in this cost.

TOTAL OF DISMANTLING AND DEMOLISHING -12,00,000.00

SH-1: SH CARRIAGE OF MATERIALS

By Mechanical Transport including loading,unloading and stacking (The rates are inclusive of GST on work contract

@18%, 15% Contractor's profit & over heads and 1% Cess etc. The rates will be applicable to net quantities after

deduction of prescribed percentage for voids mentioned in the CPWD specifications under subhead "Carriage of

b) Beyond 5 km upto 10 km per km cum 2250.00 23.16 52,110.00

c) Beyond 10 km upto 20 km per km cum 4500.00 18.85 84,825.00

d) Beyond 20 km per addl. km cum 2250.00 15.17 34,132.50

SH-2: SH EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in

2 2.6 depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m,

disposed earth to be levelled and neatly dressed.

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

3 2.26 Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding

20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.

Supplying and filling, in plinth with jamuna sand under floors including, watering, ramming consolidating and dressing

Surface dressing of the ground including removing vegetation and inequalities not exceeding 1.5 cm. deep and disposal

of rubbish lead upto 50 m and lead upto 1.5 m

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm

6 2.31 measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of sqm 2015.71 17.60 35,476.51

the area cleared.

6A 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

6A.1 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 532.25 234.75 1,24,945.39

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of

chemical emulsion) :

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre

including drilling and plugging holes etc.:

6B.1.1 2.35.2.1 With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration metre 236.56 53.45 12,643.86

TOTAL (CARRIED OVER TO SUMMARY CIVIL WORKS) 27,09,292.01

SH-4: SH CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All

work upto plinth level.

7.1 4.1.8 1:4:8 (1 Cement:4coarse sand:8 graded stone aggregate 40 mm nominal size) cum 201.57 6,812.00 13,73,102.20

Providing and laying cement concrete in retaining walls, return walls, walls(any thickness) including attached

8 4.2 pilasters,columns, piers, parapets, coping, bedblocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to

floor five level, excluding the cost of centering, shuttering and finishing:

8.1 4.2.3 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). cum 8.42 9,895.20 83,350.14

TOTAL OF CONCRETE WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS 14,56,452.34

SH-5: SH REINFORCED CEMENT CONCRETE WORK

9 5.9 Centring and shuttering including strutting, propping etc. and removal of form for:

a) 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. sqm 2986.49 842.50 25,16,116.14

b) 5.9.20 Suspended floors, roofs,landings, balconies and access platform with water proof ply 12 mm thick sqm 8637.00 1,028.40 88,82,290.80

c) 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 5906.00 961.30 56,77,437.80

d) 5.9.7 Stairs, (excluding landings) except spiral-staircases. sqm 1539.72 764.95 11,77,808.81

e) 5.9.21 Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick sqm 13966.24 841.95 1,17,58,871.94

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including

10 5.11 cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part

thereof (Plan area to be measured)

10.1 5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) sqm 5871.71 384.30 22,56,498.92

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete

upto plinth level.

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

11.1 5.22.6 Thermo-Mechanically Treated bars kilogram 3,04,571.00 107.85 3,28,47,982.35

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete

above plinth level.

12.1 5.22A.6 Thermo-Mechanically Treated bars kilogram 5,57,545.00 107.85 6,01,31,228.25

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of

concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying,

13 5.33 curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction

of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In

case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall

have discretion to either re-design the mix or bear the cost of extra cement.

13.1 5.33.1 All works upto plinth level

13.1.1 5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 1901.33 9,655.70 1,83,58,652.38

13.1.2 5.33.1.3 Concrete of M35 grade with minimum cement content of 370 kg /cum cum 18.00 9,806.70 1,76,520.60

13.1.3 5.33.1.4 Concrete of M40 grade with minimum cement content of 390 kg /cum cum 38.62 9,957.65 3,84,558.98

13.2 5.37.2 All works above plinth level upto floor V level

13.2.1 5.33.2.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 2484.10 10,011.35 2,48,69,177.47

13.2.2 5.33.2.3 Concrete of M35 grade with minimum cement content of 370 kg /cum cum 581.24 10,162.35 59,06,759.49

13.2.3 5.33.2.4 Concrete of M40 grade with minimum cement content of 390 kg /cum cum 485.91 10,313.30 50,11,289.35

14 5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. cum 887.81 355.65 3,15,749.92

TOTAL OF R.C.C WORKS CARRIED OVER TO SUMMARY OF CIVIL WORKS 18,02,70,943.20

SH-6: SH BRICK WORK

Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to

floor five level in :

15.1 6.32.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 40.46 9,095.05 3,67,985.72

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength

in super structure above plinth level up to floor V level in :

16.1 6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) cum 910.61 8,752.55 79,70,152.64

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm thick with Grade-1 AAC

blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V

level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm

dia M.S. bars at every third course of masonry work.

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or

part there of by mechanical means.

Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure

19 6.45 above plinth and upto floor V level.

19.1 6.45.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand) sqm 2498.32 1,105.80 27,62,637.83

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical

TOTAL OF BRICK WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS 1,18,97,143.85

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

SH-9: SH WOOD & PVC WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board

22 9.20 construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands

and face veneers on both faces of shutters.

22.1 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sqm 899.94 3,473.85 31,26,250.49

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on

unexposed surface etc.

23.1 9.40.1 2nd class teak wood

Providing 40x5 mm flat iron hold fasts 40 cm. long including fixing to frame with 10 mm dia. Bolts,nuts and wooden

24 9.53 plugs and embedding in cement concrete block 30x10x15 cm. 1:3:6 mix ( 1 cement :3 coarse sand 6 graded stone each 1402.00 228.85 3,20,847.70

aggregate 20 mm nominal size )

Providing & Fixing matt finished stainless steel grade 202 tower bolt ( barrel type) with necessary stainless steel screws

etc. complete as per the direction of Engineer-In-Charge.

25.1 a) 250 x 10mm with flap thickness 0.80 mm each 307.00 322.20 98,915.40

25.2 b) 250 x 10mm with flap thickness 0.80 mm each 307.00 262.76 80,667.32

25.3 c) 150 x 10mm with flap thickness 0.80 mm each 614.00 203.32 1,24,838.48

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of

approved quality with necessary screws etc. complete

Providing & Fixing matt finished stainless steel grade 202 sliding door bolts/L-Drop with necessary stainless steel screws

etc. complete as per the direction of Engineer-In-Charge.

Providing & Fixing matt finished stainless steel grade 202 tower bolt ( barrel type) with necessary stainless steel screws

28 NSR etc. complete as per the direction of Engineer-In-Charge.

28.1 a) 250 x 10mm with flap thickness 0.80 mm each 24.00 241.97 5,807.28

28.2 b) 150 x 10mm with flap thickness 0.80 mm each 24.00 152.49 3,659.76

28.3 c) 100 x 10mm with flap thickness 0.80 mm each 24.00 95.47 2,291.28

Providing & Fixing matt finished stainless steel grade 202 handles with necessary stainless steel screws etc. complete

as per the direction of Engineer-In-Charge.

Providing & Fixing matt finished stainless steel grade 202 hanging floor door stopper with necessary stainless steel

screws etc. complete as per the direction of Engineer-In-Charge

30.1 Twin rubber stopper with pin/rod dia 10mm and flap thickness 0.8mm each 106.00 70.50 7,473.00

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I.

sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60

minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround

the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire

resistant primer etc.complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-

II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame,

consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet

(zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball

bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per

direction of Engineer-in-charge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of

1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws

at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder

coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect

as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness

33 9.138 having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation sqm 180.84 40,405.55 73,06,939.66

(EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing

the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body

which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration

scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

TOTAL OF WOOD WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS 1,65,08,239.39

SH-10: SH STEEL WORK

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the

junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

34.1 10.5.1 Using M.S. angles 40x40x6 mm for diagonal braces. sqm 8.04 5,804.35 17,413.05

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through

their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with

35 10.6 brackets, side guides and arrangements for inside and outside locking with push and pull operation complete

including the cost of providing and fixing necessary 27.5cm long wire springs grade No.2 and M.S. top cover of

required thickness for rolling shutters.

35.1 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover sqm 31.68 3,653.20 1,15,733.38

36 10.7 Providing and fixing ball bearing for rolling shutters. each 24.00 492.35 11,816.40

Extra for providing mechanical device chain and crank operation for operating rolling shutters.

37.1 10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in the area sqm 192.00 1,281.35 2,46,019.20

Extra for providing grilled rolling shutters manufactured out of 8 mm dia. MS bar instead of laths as per design approved

by Enginer-in-charge ( area of grill to be measured )

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming

coat of approved steel primer using structural steel etc.as required

39.1 10.25.2 In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works kg 13674.00 172.60 23,60,132.40

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding,

grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel

nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel

bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of

Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts, fasteners etc).

TOTAL OF STEEL WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS 54,37,260.63

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

SH-11: SH FLOORING

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of

41 11.3 neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

41.1 11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 200.00 614.20 1,22,840.00

42 11.24 Extra for pre finished nosing in treads of steps of marble stone metre 982.89 719.90 7,07,584.45

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with

43 11.26 pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1

cement : 4 coarse sand):

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by

44 8.31 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 sqm 1919.99 1,267.95 24,34,444.98

coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with

pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of

1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red

45 11.38 Brown, laid on 20 mm thick bed of cement mortar sqm 739.46 1,315.30 9,72,618.07

1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white

cement and matching pigments etc., complete.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of

46 11.48 desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per

direction of Engineer-in-charge.

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water

absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade,

47 11.49 laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average

6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion

of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick

48 11.51 base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including

pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and

polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

48.1 11.51.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. sqm 721.78 6,603.35 47,66,166.43

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear

portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average)

49 11.56 thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as

specified and as directed by the Engineer-in-Charge.

49.1 11.56.1 Polished Granite stone slab of colour Black, Cherry/Ruby Red, Sapphire Blue, Honey Brown or equivalent sqm 982.89 4,481.30 44,04,637.06

49A 11.24 Extra for pre finished nosing to treads of steps of marble stone. metre 343.20 719.90 2,47,069.68

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

Supply & fixing of Wooden Flooring: The laminated wooden flooring shall be 12 mm thick, comprising a high-density

fibreboard (HDF) core with a minimum density of 850 kg/m³, overlaid with a melamine-impregnated decorative layer and

a transparent wear-resistant overlay conforming to abrasion class AC4 or higher, suitable for moderate to heavy

residential and light commercial use. Each plank shall be precision-milled with a tongue-and-groove or click-lock

interlocking system (e.g., Uniclic or equivalent) ensuring gap-free jointing without adhesive. Dimensions shall typically be

1200 mm (L) × 190 mm (W) × 12 mm (T), with V-grooved edges and an anti-bacterial, anti-fade, and UV-resistant surface

50 NSR1 finish. Backside of each plank shall be provided with a balancing layer for dimensional stability. Flooring shall be laid sqm 360.89 2,128.00 7,67,973.99

over 2–3 mm thick polyethylene or IXPE foam underlayment to provide thermal insulation and footfall sound absorption,

with expansion gaps of 8–10 mm provided along walls and fixed elements. The flooring shall comply with EN 13329

standards for laminate flooring, be termite- and moisture-resistant (with waxed edges), and carry a manufacturer’s

warranty of minimum 10 years.

TOTAL OF FLOORING WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS 2,58,64,304.32

SH-12: SH ROOFING

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections,

power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277

and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre

to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of

cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of

angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5

mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting

clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm

thick 27 mm high having flanges of 20 mm and 30 mm long,

the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall

screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry

wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square

edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of

perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with :

51.1 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board sqm 680.45 1,529.10 10,40,469.44

Fully Perforated Gypsum Plaster Board of size 1200 x2400x12.5 mm having approximate 15% perforatedv area with

51.2 12.45.4 perforation size and pattern as approved by Engineer -in -Charge and as per manufactures specification with all 4 sides sqm 559.23 1,744.15 9,75,377.21

tapered and backed by accoustical tissue with NRC value not less than 0.60

TOTAL OF ROOFING WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS 20,15,846.65

SH-13: SH FINISHING

52 13.1 12 mm cement plaster of mix:

53 13.2 15 mm cement plaster on the rough side of single or half brick wall of mix :

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

54 13.16 6 mm cement plaster of mix

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to pepare the surface even and

smooth complete .

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/

56 13.41 litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade

New wor (Two or more coats) over and including water thinnable priming coat with cement primer having VOC content

less than50 gram/ litre

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content

57 13.83 less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to

achieve even shade and colour.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound )

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre

58.2 13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre sqm 749.00 73.95 55,388.85

59 13.63 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

59.1 13.63.1 Two or more coats on new work sqm 2322.00 146.80 3,40,870.19

TOTAL OF FINISHING WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS 1,51,16,472.56

60 SH-16: SH ROAD WORK

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed

concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by

60.1 16.75 floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel cum 314.95 9,823.80 30,94,005.81

shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum.

Excess/less cement used as per design mix is payable/ recoverable separately).

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a

mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform

layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to

achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

60.3 16.78.3 With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20 cum 419.93 2,808.55 11,79,394.40

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix

macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in

60.4 16.79 uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with cum 262.46 2,914.30 7,64,887.18

vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of

Engineer-in-Charge

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate

conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1,

aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum

60.5 16.80 moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at cum 209.96 4,148.65 8,71,050.55

7days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-

10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge.

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

TOTAL OF ROAD WORKS CARRIED OVER TO SUMMARY OF CIVIL WORKS 59,09,337.94

SH-22: SH WATER PROOFING

Providing and laying integral cement based water proofing treatment including preparation of surface as required for

treatment of roofs, balconies, terraces etc consisting of following operations:

Applying a slurry coat of neat cement using 2.75 kg/sqm of cement

(a) admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab

including adjoining walls upto 300 mm height including cleaning the surface before treatment.

Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1

cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-

(b) charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the

adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with

water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.

Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of

approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making

pattern of 300x300 mm square 3 mm deep.

The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.

“All above operations to be done in order and as directed and specified by the Engineer-in-Charge”:

61.1 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. sqm 1291.72 1,684.60 21,76,023.09

TOTAL OF WATER PROOFING WORK CARRIED OVER TO SUMMARY OF CIVIL WORKS 21,76,023.09

SH-25: EXTERIOR FINISH (FAÇADE)

63A NSR2 ZINC CLADDING

SUPPLY & INSTALLATION: ZINC TITANIUM WALL CLADDING

Supply, Fabricate, Package of Flat Lock cladding System in ZINC-Titanium alloy

The Zinc Titanium Wall Cladding system comprises flat-lock panels manufactured from premium Titanium-Zinc alloy

(rolled zinc alloyed with copper and titanium) conforming to EN 988, with 0.8 mm panel thickness. Panels are a

maximum of 390 mm wide × up to 2,000 mm long; typical lengths expected between 1,000–2,000 mm to guide bids.

They are fixed to galvanized aluminum substructure (25 × 50 mm box sections at 600 mm centers) using 0.4 mm HDG

clips designed to resist 50 daN pull-out, suitable for Mumbai coastal wind conditions. The alloy features a pre-weathered

zinc phosphate (hopeite) layer, overlaid with a 15 µm primer, 20 µm polyurethane resin, and 12 µm back-varnish, yielding

a bright grey finish akin to natural zinc patina.

A grey 0.6 mm HDPE anti-abrasive membrane, placed with 8.6 mm air gap at 19.5 mm spacing, provides 250 kN/m²

compression resistance and DIN 4102 B2 fire rating. Beneath this, a 0.47 mm TCT high-tensile steel decking sheet with

3.5 mm ribs at 50.5 mm pitch is installed onto a GI hat section. Flashings—corners, tops, bottoms—are formed from

0.8 mm VMZINC, matching the façade finish. All materials must be sourced from VMZINC, Silesia, Fedrus, RHEINZINK

or ELZINC high-quality options such as RHEINZINK or ELZINC, provided full EN 988 certification and execution

traceability via Indian project POs are submitted.

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

Installation is to be executed by specialist flat-lock cladding contractors with documented experience (minimum

1000 sqm with these systems) and ISO certification. Installer scope includes precise on-site fabrication, fastening with

HDG screws/fasteners, flashings, and quality checks.

Item includes Designing, Supplying, installation and fixing of profiled zinc panels including HDG screws / fasteners,

flashings as required for the project.Installation to Be carried out by Specialised agency meeting the prequalification

criteria listed in Technical specifcations of the item.

ZINC CLADDING complete described as above sqm 232.35 8,280.00 19,23,858.00

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour

board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut

for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade),

calcium corbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity

index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face)

minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class

A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild

steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel

primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS

screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat

and necessary SS fasteners and SS screws shall be paid separately.

V) STRUCTURAL GLAZING

Design, fabricate, test, protect, install and fix a semi-unitized structural glazing façade system—comprising linear and

curvilinear modules at all heights—in compliance with IS 875 Part III, including shop drawings for specified loads and

proof testing at 1.5× design wind pressure. The system shall include high-performance framing to accommodate various

glass thicknesses, EPDM and silicone gaskets, stainless-steel toggles, clamps, sealants, flashings, fire/smoke barriers,

drainage, and pressure-equalisation features. Serrated MS hot-dip galvanized or 6005-T5 aluminium brackets shall

permit 3D accommodation and ensure verticality, affixed to the structural subframe via 316-grade stainless steel anchors

with nylon separators. In a controlled factory environment, all glazing shall be sealed with two-part structural silicone and

compatible weather sealant, plus spacer tape, setting blocks, and backer rods per approved design. Perimeter flashings

of 1 mm aluminium will seal interfaces, while gutters, weep holes, and pressure-equalisation will manage moisture

The scope includes full labour, scaffolding, T&P, temporary works, and on-site assembly, with all shop drawings

engineer-certified, mock-ups fabricated and tested in NABL-accredited labs, and field verification of the completed

glazing. The façade must be delivered watertight, performance-compliant, clean, and protected, as per architectural and

approved drawings under engineer supervision.

b) Glazing area shall be measured on the external glazed face, including groove widths, to two decimal places

Nothing extra or separate items shall be payable for aluminium frames, capping, vermin-proof mesh, etc. All costs are

included in this item only

For façade areas exceeding 2,500 m², mandatory testing (at contractor’s expense) shall include air-leakage

d) (ASTM E‑283), static/dynamic water penetration (ASTM E‑331, AAMA 501.1), structural deflection (ASTM E‑330),

seismic movement (AAMA 501.4), and on-site water-leakage testing up to 240 kPa.

All aluminium components—including mullions, transoms, sub-frames, and vent frames—shall be precision-fabricated

from 6063-T5/T6 alloy extrusions in line with BS 1474. Extrusions will be cut, machined, drilled, and punched for

connectors, gaskets, anchors, and sealant contact surfaces—with CNC or laser accuracy—to ensure tight dimensional

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

Profiles will be anodized (minimum 20 µm) or PVDF/powder-coated (minimum 35 µm) per project color standards. The

f) fabrication process includes installing serrated MS or aluminium brackets, shoe brackets, telescopic couplings, gaskets,

and all hardware such as stainless-steel screws, connectors, splice plates, cleats, and fasteners .

In a controlled factory setting, aluminium cells or modules are assembled: mullions and transoms joined with stamped

gaskets; secondary support gaskets and insulation inserted; glass panels or insulated vision/spandrel units installed;

perimeter seals applied; and modules are quality-checked and shipped to site fully assembled—typical of unitized or

semi-unitised systems

Glass selection shall support green building certification:

• Option 1: Guardian SunGuard Solar Prime Sea Green 35 (cool blue-green coated glass) with VLT≈38%, SHGC≈0.35,

low interior/exterior reflection, and proven thermal/solar performance .

• Option 2: Guardian SunGuard Solar Plus series (clear low-E monolithic or DGU) delivering high solar protection, low

h) emissivity, and green-building alignment.

• Option 3: Vitro Solarban® 70 (triple-silver coated low-E glass) offering neutral appearance, VLT≈64%, SHGC≈0.27 in

IGU, established performance and reduced HVAC loads.

Equivalent alternatives include Solarban 70 Optiblue, R100, or Solarban 60, depending on aesthetic or performance

priorities. These options have national presence in India and support LEED/IGBC/Griha compliance.

Openable vent inserts shall include:

a) Top-hung AWS 48.NI or equivalent (Schüco, Reynaers, YKK AP, Aluplast) – 48 mm frame, EPDM gaskets, 1.75 kPa

wind rating, EN-certified air ±600 Pa and water ±720 Pa, proof loaded ±2.5 kPa, concealed heavy-duty friction stays

i) tested for ≥20,000 cycles, multi-point locking, powder coat ≥60 µm.

b) Parallel pop-out thermally broken vents with 31 mm room face, 20 mm sash, 93 mm depth, triple rebate gaskets,

factory glazed IGUs, and mechanical glass retention for heights >8 m. Bonding position 4 IGUs require project-specific

regulatory approval.

Vision glazing shall be Saint-Gobain insulated units (6 mm SKN 144 II + 12 mm air gap + 6 mm clear/ coloured

toughened) delivering VLT 22%, reflections 29%/21%, shading coefficient 0.25–0.28, and U-value ≈5.6 W/m²·K.

The façade’s vision panels will be factory-assembled as 6 mm – 12 mm spacer – 6 mm pane Insulated Glass Units

(IGUs), offering structural integrity, thermal/sound insulation, and aesthetic performance. High-quality float glass—clear,

tinted ("cool series"), or low-E—will be cut precisely to size, edged, washed, and dried in controlled conditions (<24 °C,

<62% RH). Aluminium spacer bars (12 mm) are pre-cut or bent to shape, filled with desiccant (silica or zeolite), sealed

with primary butyl, and assembled between two 6 mm glass lites using an automatic pressing machine. The spacer joins

via either corner keys or single-piece bends to minimize thermal bridging. After pressing, the cavity may be evacuated

and backfilled with argon for enhanced thermal performance. A secondary seal, typically polysulphide or structural

silicone, is applied around the perimeter before transferring to curing racks. The finished IGU undergoes inspection for

clarity, dimensional accuracy, seal integrity, gas retention, and conformity to standards (e.g., EN 1279‑2), with the

desiccant ensuring no condensation forms within the unit

For cool-series glass, the outer 6 mm lite may consist of Guardian SunGuard Sea Green or Solar Neutral, Saint‑Gobain

Cool‑Lite, or Vitro Solarban low‑E glass—each capable of supporting IGU assembly. The inner pane matches the

l) performance glazing specified previously (e.g., Saint‑Gobain SKN 144 II or clear toughened). These IGUs combine to

deliver optimal visible-light transmittance, solar heat gain coefficients, U‑values, and shading coefficients in line with

green building criteria.

Integrating this IGU fabrication protocol within the structural glazing assembly ensures consistent quality, performance

compliance, and watertight integrity. If desired, factory mock-ups of full-size 6‑12‑6 units—including corner detail and

argon fill verification—will be conducted in NABL-approved labs to confirm optical and thermal performance prior to site

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

Spandrel cladding includes 50 mm Twiga glass wool (48 kg/m³), black woven fabric liner, 1 mm GI backpan, SS‑304

fixings, and 6 mm tinted toughened overlay matching vision glazing. Fire-stopping comprises 100 mm 100 kg/m³

n) Rockwool slabs with GI flashings and 10 mm intumescent seals, creating a 2-hour fire-rated, acoustically isolating barrier

at RCC slab intersections. Single glass spandrel panels will use 6 mm ST-series toughened glass in approved finish.

Spandrel panels will be factory-manufactured IGU units featuring opaque backing to conceal the slab edge or building

services, typically produced with a ceramic-frit or enamel coating on the interior face of monolithic glass or IGU

surface #4. A typical insulated spandrel panel comprises two glass lites—6 mm clear or tinted outer glass, and an inner

o) glass with enamel/ceramic frit—bonded with insulating spacer and filled with mineral wool or foam insulation (e.g., glass

wool, polyiso, or cross-linked polyethylene), per SAF's insulated spandrel pan methodology, with moisture-resistant, fire-

rated core mechanically secured by welded pins and fastened to aluminum or galvanized-steel trays to match curtain

The outer surface may be painted or fritted to match vision glazing palettes, ensuring thermal stability through heat-

strengthening and compatibility validation between coating and insulation . All spandrel units are prefabricated to size,

complete with insulation, glazing, backing tray, fire barrier flashing, and ready for immediate installation, ensuring

structural, fire and acoustic performance, as well as seamless visual integration .

On-site installation begins with thorough site preparedness: verifying structural embedment levels, ensuring clean,

primed interfaces, then fixing vertical mullions and horizontal transoms to the building using halfen-type or similar

q) adjustable steel brackets. Alignment, plumb, and level checks are conducted before securing anchors. Prefabricated

modules are then hoisted into position via crane or mounted in a stick-by-stick approach. Once seated, upper and lower

anchors are adjusted for precise alignment .

After installation, glazing procedures proceed: the modules are pressure-sealed or face-sealed using structural silicone

(e.g., Dow, GE), EPDM gaskets, stainless steel toggles/clamps, and weather sealants. Joints and fixture points are

r) sealed, flashings fitted, and perimeter silicone applied for air and watertightness . Glass : Guardian SunGuard /

ClimaGuard (Gujarat Guardian Glass), Saint-Gobain SGG Cool-Lite series, Vitro Solarban® Series (e.g.,

Solarban 70/60)

Field testing and quality control include random peel-off tests for silicone adhesion, curtain wall plumb and level

verification, water-tightness and air-infiltration tests (e.g., spray test, blower door), and integrity inspections of sealant

joints, glass clarity, and frame surfaces. Final cleaning, removal of protective films, and handover inspections complete

During storage, glass and aluminium components are protected carefully: glass on A-frames at 15° angle, shielded with

wooden or rubber padding; aluminium on racks with batten layers—sealed from moisture and dust. The entire

installation follows a typical unitized curtain wall sequence: factory prefabrication → site hoisting → anchor adjustment

→ sealant application → final QA and commissioning

Complete STRUCTURAL GLAZING as described above sqm 3403.34 8,510.00 2,89,62,423.40

VI) TEXTURED PAINT

65 NSR Finishing walls with textured exterior paint of required shade :

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

Walls shall be thoroughly prepared—substrates must be cleaned of dust, oil, algae, and loose material; cracks repaired;

and moisture reduced to ≤15% before treatment. Start with an exterior-grade waterproofing basecoat, such as Dulux

Aquatech Exterior Waterproof Basecoat (crack-bridging up to 2 mm, 8-year performance) or NeoSeal 504 PrimeCoat

(acrylic, efflorescence-resistant, flexible waterproof sealer), applied in a single coat at ~8–10 m²/L and allowed to cure

per manufacturer guidelines. Once waterproofed, apply an alkali-resistant exterior primer, such as Asian Paints

SmartCare Primero or Indigo Water-Thinnable Sealer Primer (5-year warranty), at 2.20 kg/10 m², ensuring proper

adhesion and sealing and key for textured layers. Upon primer curing (minimum 12–16 hours), a thick texture finish shall

follow with two or more coats (approximately 3.28 litres per 10 m² per coat) to achieve a robust textured thickness of

1.5–3 mm, applied via spray, roller, or stainless-steel trowel depending on the chosen texture style (e.g., fine sand,

pebble, rustic). Use only minor water dilution (up to 10%, if recommended); ensure environmental conditions between

10–40 °C and humidity < 80%, avoiding rain or direct intense sunlight during application.

Throughout execution, measure wet film thickness (comb gauge) and verify dry thickness (digital gauge) to meet

performance specs. Perform adhesion testing (cross-cut per IS 101 Part 5 or ASTM D3359), opacity/hiding, viscosity,

and alkali resistance checks for every batch of Asian Paints Apex Createx / Ultima Allura, JSW Wall Texture Tough

Exteriors, Surfa Coats Surfa Nova / Surfatex, Birla Opus Prime T30The finished surface must be uniform, crack-free,

breathable, weather-resistant, UV-stable, and exhibit no sagging, blistering, or colour variation.

A minimum 5-year manufacturer’s warranty against peeling, mould/algae, and fading is required. Before full-scale work,

the contractor shall prepare a 2 × 2 m sample panel for approval by the Architect/Engineer to confirm texture, shade,

finish, and workmanship.

65.1 a) New work (Two or more coats applied over and including priming coat of exterior primer and paint sqm 2683.70 2,630.00 70,58,131.00

IV) GRC (Glass Reinforced Concrete)

The GRC Jali shall be factory-manufactured using Glass Fibre Reinforced Concrete (GRC) panels, fabricated through

the spray-up or premix process as per international standards such as GRCA (Glass fibre Reinforced Concrete

Association - UK) guidelines. The material shall comprise a matrix of alkali-resistant (AR) glass fibres (minimum 5% by

weight) dispersed within a high-grade white/grey Portland cement (OPC 43/53 grade) and silica sand mix, polymer-

modified for enhanced flexibility and durability. The typical composition shall include white cement, fine silica sand,

water, acrylic polymer (3–5%), alkali-resistant glass fibre (≥5% by weight), and other proprietary additives to enhance

workability and performance.

The GRC Jali shall be cast in approved moulds to achieve sharp detailing and uniform patterns as per approved

architectural design/drawing. The standard thickness shall be 20–25 mm, with ribs and stiffeners integrated at the back if

66 NSR4 required for structural stability. Panels shall be dimensionally accurate, crack-free, with smooth, sandblasted, or custom sqm 251.83 4,600.00 11,58,436.40

surface finish as per architectural requirement. Compressive strength of GRC shall be ≥40 MPa, flexural strength ≥8

MPa, and density between 1800–2000 kg/m³. The Jali shall be factory-cured for minimum 7 days and air-dried before

dispatch. Jali panels shall be installed using approved stainless steel brackets, anchor fasteners, and framing system

with provision for thermal movement, vertical loads, and wind pressure as per structural design.

Measurement shall be taken for the net area in square meters (sqm) of installed Jali excluding open voids, and including

curvature or pattern as shown in elevation. Approved makes: as approved by the Engineer-in-Charge. All work shall be

executed as per manufacturer specifications and architect’s design intent.

TOTAL OF EXTERIOR FINISH (FAÇADE) 18,63,450.87

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

64 ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular

sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with

dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides

with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and

64.1 21.1 jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass

/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,

paneling and dash fasteners to be paid for separately) :

64.1.1 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) kg 1147.73 530.90 6,09,332.23

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing

65 21.1.2 of fittings wherever required including the cost of EPDM rubber /neoprene gasket required (Fittings shall be paid for

65.1 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) kg 765.16 634.45 4,85,453.42

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber /

66 21.3 neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic item):

66.1 21.3.3 With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) sqm 225.05 1,685.40 3,79,292.49

TOTAL OF ALUMINIUM WORK 14,74,078.14

LANDSCAPING & HORTICULTURE WORK

A Landscaping Schedule

Providing and fixing Glass mossaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour,

design including the cost of cement mortar in required thickness for base plaster, fixing in customize design including

groting with white cement mixed with pigment of approved colour and as per direction of PMC/Architect. The glass

mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and

grouting of the same. The rate is inclusive of all operation, material and required pattern approved by PMC/Architect.

B Development Schedule -

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with

proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface

smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per

direction of officer-in-charge.

Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy

variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. The rates shall

include mortality replacement and maintanance for period of 6 months or handing over of the project , which ever is

Providing and displaying of Aglaonema Butterfly plant having ht.30 cm 10 to 12 fresh, healthy and attractive colorful

leaves, well developed in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge. The rates shall

include mortality replacement and maintanance for period of 6 months or handing over of the project , which ever is

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

Quantity Rate (Rs.) Amount (Rs.)

S. No. Description Of Item Unit

Providing and Displaying Antirrhinum Hybrid dwarf variety, specimen (8-10) with fresh & healthy foliage in full bloom well

developed in 35 cm Earthen Tray/Challi Pot and as per direction of the officer-in-charge. The rates shall include

mortality replacement and maintanance for period of 6 months or handing over of the project , which ever is later.

Providing and Displaying Portulaca hybrid in different colour with bloom well developed fresh & healthy in 20 cm Earthen

74 4.79 Pot/Plastic Pot and as per direction of the officer-in-charge. The rates shall include mortality replacement and Each 2298.00 86.10 1,97,857.80

maintanance for period of 6 months or handing over of the project , which ever is later.

Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with

75 4.93 one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. The rates shall include mortality Each 1806.00 150.70 2,72,164.20

replacement and maintanance for period of 6 months or handing over of the project , which ever is later.

Providing and Displaying Adenium Obesum well developed with fresh & healthy 4 to 5 branch 60 to 75 cm ht. in 40 cm

76 5.6 size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.. The rates shall include mortality replacement and Each 525.00 563.75 2,95,968.75

maintanance for period of 6 months or handing over of the project , which ever is later.

Providing and stacking of Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh

and healthy leaves in 30 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. The rates shall

include mortality replacement and maintanance for period of 6 months or handing over of the project , which ever is

Providing and stacking of Ficus blackii (F.vivion) (bushy) of height 150-165 cm. with 8-10 branches and healthy foliage in

78 8.23 earthen pots of size 30 cm as per direction of the officer-in-charge. The rates shall include mortality replacement and Each 1680.00 250.00 4,20,000.00

maintanance for period of 6 months or handing over of the project , which ever is later.

Providing and stacking of Hibiscus variegated of height 60-75 cm. with 8-10 branches and healthy variegated foliage in

79 8.39 cement pots of size 35 cm as per direction of the officer-in-charge. The rates shall include mortality replacement and Each 840.00 180.00 1,51,200.00

maintanance for period of 6 months or handing over of the project , which ever is later.

Providing and stacking of Petra volubilis of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per

80 9.11 direction of the officer-in-charge. The rates shall include mortality replacement and maintanance for period of 6 months Each 2260.00 48.00 1,08,480.00

or handing over of the project , which ever is later.

TOTAL OF LANDSCAPING & HORTICULTURE WORK 69,80,258.25

Digitally signed by VARUN

NBCC (INDIA) LIMITED CIVIL WORKS SINGH

PROPOSED CONSTRUCTION OF WRPC - ANDHERI MUMBAI

COST SUMMARY OF PLUMBING WORKS

S. NO. DESCRIPTION AMOUNT (DSR-2023) AMOUNT ( NSR ) TOTAL (Rs.)

1 SANITARY FIXTURE & FITTINGS 31,95,284.00 12,67,797.00 44,63,081.00

2 SOIL, WASTE , VENT WATER PIPES 46,44,076.00 2,97,528.00 49,41,604.00

4 PUMPS, WATER TREATMENT & ALIED EQUIPMENT - 64,84,115.00 64,84,115.00

5 ELECTRICAL PANEL BOARDS FOR PHE WORKS. - 4,48,500.00 4,48,500.00

7 ROOF TOP SOLAR WATER HEATER SYSTEM - 5,32,818.00 5,32,818.00

8 WATER COOLER +RO+UV SYSTEM - 17,76,060.00 17,76,060.00

TOTAL ( DSR+NSR ) 2,33,37,262.00

NBCC (INDIA) LIMITED PLUMBING WORKS

Digitally signed by VARUN

PROPOSED CONSTRUCTION OF WRPC - ANDHERI MUMBAI

BOQ FOR PLUMBING & WATER SUPPLY WORKS

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

SECTION A- PLUMBING WORKS.

SUB HEAD I - SANITARY FIXTURE & FITTINGS

1.2 17.78 Providing and fixing white vitreous china extended wall mounted water closet of

size 780X 370X690mm of approved shape including providing and fixing of

white vitreous china cistern with dual flushing fitting of flushing capacity 3 liter/6 Each 101 14,999.15 15,14,914.15

liters (Adjustable to 4liter/8liters) including sheet cover , and cistern fittings, nut

bolt gasket etc complete.

1.4 17.7 Provinding and fixing was basin wih C.I brackets, 15 mm dia CP Brass single

hole basin mixer of approved quality and make, including painting of fittings and

brackets, cutting and making good the walls whereever required :

17.7.4 White Vitreous China Wash basin size 550x400 mm with a 15mm CP Brass

single hole basin mixer

1.5 17.5 Providing and fixing white vitreous china flat back half stall urinal of size 580 x

380x350 mm with white P.V.C automatic flushing cistern, with fittings, standard

size C.P brass flush pipe, spreaders with unions and clamps (all in C.P brass)

with waste fitting as per IS : 2556, C.I trap with outlet grating and other coupling

in C.P brass including painting of fittings and cutting and making good the walls

and floors whereever required

17.5.2 Range of two half stall urinals with 5 litre P.V.C automatic flushing cistern Each 46 18,008.75 8,28,402.50

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

Providing and fixing white glazed vitreous china urinal partition of size 90 × 320 ×

720 mm, conforming to IS:2556 or equivalent, fixed with expandable anchor

fasteners, chromium-plated brass bolts and washers, embedded in wall and set

in cement concrete 1:2:4, including cutting, drilling and making good the wall Each 32 2,818.00 90,176.00

surface with matching plaster/finish. The partition shall be properly aligned,

leveled and cleaned after fixing, complete in all respects as per the direction of

Engineer-in-Charge.

1.7 NSR 2 Providing and fixing 8mm thick float glass mirror with beveled and polished

edges, fixed over 12mm thick BWP grade marine plywood (IS:710) backing using

high-quality neutral cure silicone, screws, and required moldings, all complete.

Mirror shall be silver-backed, distortion-free, and installed with smooth edge

alignment and seamless joints. The scope includes supply of all materials, sqm 10 4,250.00 42,500.00

labour, tools, scaffolding at all heights, cleaning after installation, and protection

of the mirror surface until handover, as per the direction of the Engineer-in-

1.8 17.31 Providing and fixig 600x450 mm beveled edge mirror of superior glass (of

approved quality) complete with 6 mm thick hard board ground fixed to wooden Each 113 1607.95 1,81,698.35

cleats with C.P. Brass screws and washers complete

1.6 17.33 Providing and fixing 600x120x5 mm glass shelf with edges round off,supported

on anodised aluminium angle frame with C.P. brass brackets and guard rail

complete fixed with 40 mm long screws,rawl plugs etc. complete. Each 113 1083.50 1,22,435.50

1.7 17.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden

cleats with CP brass screws with concealed fittings arrangement of approved

quality and colour.

17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective

height of 88 mm, weighing not less than 170 gms.

1.8 18.53 Providing and fixing CP brass angle valve for basin mixture and geyser points of

approved quality confirming to IS: 8931.

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

1.9 18.63 Providing and fixing PTMT angle stop cock 15mm nominal bore,weighting not

less than 85gms.

1.10 17.70 Providing and fixing PTMT Bottle Trap for Wash basin.

Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of

17.70.1 tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 Each 113 367.10 41,482.30

mm minimum water seal, weighing not less than 260 gms.

1.11 18.65 Providing & Fixing PTMT soap dish holder having legth of 138mm breadth

102mm height of 75mm with concealed fittings arrangements ,weighing not less Each 113 111.45 12,593.85

1.12 NSR 3 Providing and fixing CP brass single lever low-flow sink mixer (deck mounted)

and 15 mm CP brass single lever pillar cock, both of approved quality conforming

to IS:8931, with chrome plating ≥10 micron, including pop-up waste system and

accessories such as inlet connection hoses, wall flanges, washers, and

fasteners. Flow rate shall be ≤6 LPM at 3 bar (Green Building Compliant). All Each 6 4,428.00 26,568.00

items shall be fixed on counter or wall as required, including necessary cutting

and making good the walls, fittings, and joints complete in all respects, as per

direction of Engineer-in-Charge. Minimum 7-year warranty shall be provided by

1.14 NSR 4 Providing, fixing, testing, and commissioning of CP brass wall-mounted single-

lever shower mixer with built-in spout, provision for overhead shower, and

spout/shower diverter, conforming to IS:8931, with a minimum chrome plating

thickness of 10 microns, complete with wall flange, escutcheon plate, and

necessary operating knobs. The mixer shall have hot and cold water inlets,

operate under a working pressure of 1.0 to 6.0 bar, and be compatible with low-

flow water-saving applications (≤6 LPM @ 3 bar). All accessories required for Each 20 5,233.00 1,04,660.00

installation, including brackets, seals, and fixings, shall be supplied. The scope

includes cutting and making good the wall surface and ensuring leak-proof

connections. The item shall carry a minimum 7-year OEM warranty, and all

installations shall be carried out as per the manufacturer’s specifications and the

direction of the Engineer-in-Charge.

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

1.15 NSR 5 Providing, fixing, testing and commissioning of CP brass wall-mounted shower

arm, 115 mm long, with wall flange and pressure-adjustable CP brass shower

rose of diameter not less than 75 mm, suitable for working pressure between 1 to

6 bar, complete with all accessories such as gaskets, fittings, and wall plugs. The

CP plating shall be of minimum 10 micron thickness, conforming to IS:8931 or Each 20 974.00 19,480.00

equivalent standards. The item shall include cutting and making good the wall

surfaces, cleaning after installation, ensuring leak-proof joints, and shall be

supplied with a minimum 7-year OEM warranty, all as per the direction of

Engineer-in-Charge.

1.17 Providing and fixing 8 mm dia C.P / S.S. Jet with flexible tube upto 1 meter long

17.16 A with S.S triangular plate to Eureopean type W.C of quality and make as approved Each 101 349.15 35,264.15

by Engineer-in-charge

1.18 NSR 6 Providing, fixing, testing, and commissioning of a 230 V single-phase SS 304

wall‑mounted, touch-free hand dryer with fully hygienic operation, rated at

1500–2000 W, airflow ≥90 m/s, drying time ≤15 s, noise ≤70 dB, IPX1 splash

protection, complete with sensor, mounting hardware, cabling, wall finish repairs, Each 50 9,758.00 4,87,900.00

and operation documentation. The unit shall be BIS and CE certified, include 3-

to 5-year warranty, and all installations shall be carried out per manufacturer’s

specs and EIC directions.

Provide and fix Macfit single-body straight WC pan connector (110 mm/4″ outlet,

inlet 97–107 mm) in flexible EVA, push-fit with spring‑loaded seal guard and

integral fins, including adaptor bush for CI pipe. The connector shall comply with

BS 5627, be leak-proof, and supplied complete with installation accessories.

Supply labour, cutting, jointing, pressure test, and making good the wall surface

as directed. The OEM shall have minimum 5 years India presence, be ISO

certified, and offer a minimum 10‑year product warranty

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

1.20 NSR 8 Providing and fixing a 700 mm long, Ø 32 mm wall-mounted grab bar, made of

SS 304 brushed finish, rated for 600 N load, complete with concealed mounting

flanges, M8 stainless steel screws, and wall plugs. The bar shall be installed

horizontally at 850 mm above finished floor level, including drilling, anchoring, Each 11 3,956.00 43,516.00

alignment, and making good the wall surface. The unit shall be from an ISO 9001-

certified manufacturer and carry a minimum 5-year warranty.

1.21 18.58 Providing and fixing PTMT grating of approved quality and colour.

1.21.1 18.58.1 Circular/square type

a) 18.58.1.1 100 mm nominal dia/size. Each 238 37.60 8,948.80

b) 18.58.1.2 125 mm nominal dia/size with 25 mm waste hole. Each 0 51.85 -

1.22 NSR 9 Providing, fixing, testing, and commissioning of satin-finish AISI 316 stainless

steel wall-mounted coat hook with a single 60 mm projection and base plate sized

40 mm×40 mm, complete with stainless steel screws, nylon plugs or adhesive

backing for wooden doors. The hook shall support a minimum 5 kg load, be from Each 101 523.00 52,823.00

an ISO 9001-certified manufacturer, and carry a 3-year warranty, installed as per

the direction of the Engineer-in-Charge

1.24 17.10 Providing and fixing stainless steel A ISI 304 (18/8) kitchen sink as per I.S.13983

with C.I. Brackets, stainless steel plug 40mm including painting of fittings and

brackets cutting and making good the walls wherever required.

a) 17.10.1 Kitchen sink with drain board

b) 17.10.2 Kitchen sink without drain board

1.25 18.49 Providing & fixing C.P brass bib cock of approved quality conforming to IS :8931.

a) 18.49.1 15 mm nominal bore Each 32 506.80 16,217.60

1.26 18.51 Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

a) 18.51.1 15 mm nominal bore Each 16 798.95 12,783.20

1.27 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

a) 18.21.2 45 cm length

b) 18.21.2.1 15 mm nominal bore Each 210 97.75 20527.5

1.28 NSR 10 Providing, installing, testing & commissioning of a 2 L vertical storage-type

electric water heater with copper storage tank, glass-wool insulation, stove-

enameled MS outer body, thermostatically controlled heater and pilot neon lamp

of, 15 mm inlet stopcock, 15 mm CP flexible connection pipes, and pressure

safety valve, suitable for 8 kg/cm² working pressure. The heater shall be BIS & 5-

star BEE rated, vertically wall-mounted with necessary brackets, and

supplied/installed as per manufacturer instructions. All installation materials,

labor, wall repairs, and commissioning are included. OEM shall be ISO/BIS

certified, with a minimum 3-year warranty.

a) Capacity 25 litres Each 42 8610.28 3,61,631.76

1.29 17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and

112 mm distance from wall of standard shape with bracket of the same materials

with snap fittings of approved quality and colour, weighing not less than 105 gms. Each 114 168.35 19191.9

1.30 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm

wide with minimum distances of 37 mm from wall face with concealed fittings

arrangement of approved quality and colour, weighing not less than 88 gms. Each 20 231.95 4639

TOTAL OF SUB HEAD I - SANITARY FIXTURES 31,95,283.70 12,67,796.56

SUB HEAD II - SOIL, WASTE , VENT WATER PIPES

2.01 17.35 Providing and fixing soil, waste and vent pipes

17.35.1.2 Centrifugally cast (spun) iron socket & Spigot (S & S) Pipe as per IS 3989 Metre 1730 1,180.75 20,42,697.50

17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS 3989 Metre 980 1,186.00 11,62,280.00

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

17.37 Providing and fixing M.S. holder bat clamps of approved design to sand cast

iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10

x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate

20mm nominal size ) including cost of cutting holes and making good the walls

2.03 17.39 Providing and fixing plain bend of required degree.

17.39.1.2 sand cast iron S & S as per IS: 3989 Each 400 390.75 1,56,300.00

17.39.2.2 sand cast iron S & S as per IS: 3989 Each 220 390.50 85,910.00

2.04 17.44 Providing and fixing single equal plain junction of required degree .

17.44.1.2 sand cast iron S & S as per IS: 3989 Each 309 811.90 2,50,877.10

17.44.2.2 sand cast iron S & S as per IS: 3989 Each 309 470.40 1,45,353.60

2.05 17.56 Providing and fixing terminal guard.

17.56.1.2 sand cast iron S & S as per IS: 3989 Each 40 506.00 20,240.00

17.56.2.2 sand cast iron S & S as per IS: 3989 Each 40 404.75 16,190.00

2.07 17.60 Providing and fixing trap of self cleansing design with screwed down or hinged

grating with or without vent arm complete, including cost of cutting and making

good the walls and floors.

17.60.1 100mm inlet and 100mm outlet

17.60.1.1 sand cast iron S & S as per IS: 3989 Each 35 1,996.50 69,877.50

2.12 12.41 Providing and fixing on wall face unplaqsticised- PVC rain water pipes

confirming to IS: 13592 TYPE A, including jointing with seal ring confirming to IS:

5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

c) NSR 11 Providing and fixing uPVC SWR Type A single-socketed rainwater pipe, 160 mm

diameter, IS 13592:2021 pressure Class 6 kg/cm², jointed with IS 5382 seal rings,

leaving 10 mm thermal expansion gap, supplied and fixed on wall face using PVC-

coated MS clamps spaced at max 1.2 m centres, including necessary fittings Metre 400 690.69 2,76,276.00

(couplers, bends, end caps), drilling, wall plugs, and making good complete, as

directed by Engineer-in-Charge.

2.13 Providing and fixing on wall face unplaqsticised- PVC moulded fitting/

accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592

TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm

gap for thermal expansion, (i) Single socketed pipes.

a) Single Tee with door

b) NSR 12 Providing and fixing on wall face uPVC SWR Type A single-socketed tee with

access door, size 160 × 160 × 160 mm for 160 mm dia rainwater piping, IS:13592

Type A, jointed with IS:5382-compliant seal ring, leaving 10 mm thermal

expansion gap, fixed using PVC-coated MS clamps at 1.2 m spacing, including all Each 60 318.78 19,126.80

required cutting/drilling and making good of walls, per piece, from BIS-certified,

f) NSR 13 Providing and fixing on wall face unplasticised PVC (uPVC) SWR Type A single-

socketed tee with access door, size 110 × 110 × 110 mm, suitable for 110 mm

diameter rainwater piping, conforming to IS:13592 Type A, jointed using IS:5382-

compliant rubber seal rings, with 10 mm thermal expansion gap, and fixed to wall Each 20 106.26 2,125.20

using PVC-coated MS clamps at 1.2 m intervals, including cutting, drilling, and

making good the wall surface complete, as per the direction of the Engineer-in-

2.14 12.22 Making khurras 45x45 cm. with average minimum thickness of 5 cm cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) over PVC sheet1mx1mx400 micron, finished with12 mm cement Each 14 298.25 4,175.50

plaster1:3 (1 cement : 3 coarse sand) and a coat of neat cement, roundingthe

edges and making and finishingthe outlet complete

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

2.15 19.2 Providing and laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand: 10

graded stone aggregate 40 mm nominal size) alround CI/ stoneware pipes

including in bed for pipes to be laid in trenches as per standard details.

TOTAL OF SUB HEAD II - SOIL,WASTE & VENT WATER PIPES 46,44,076.45 2,97,528.00

SUB HEAD III - INTERNAL WATER SUPPLY

3.01 18.10 Providing & fixing GI pipes complete with GI fittings and clamps, including cutting

& making good the walls etc.

Internal work- Exposed on wall

h) NSR 25 Providing and fixing G.I. (galvanized iron) pipes, 80 mm nominal bore (NB),

medium class, confirming to IS:1239 (Part 1):2004, complete with G.I. fittings

(such as elbows, tees, sockets, unions, nipples) and galvanized iron clamps at

regular intervals. The piping shall be fixed exposed on wall (internal work),

including cutting, threading, welding (if required), and making good the wall

surface with cement mortar/plaster to match existing finish. All pipes shall be Metre 600 595.06 3,57,033.60

tested to specified pressure after installation. The rate shall include the cost of all

materials, labour, scaffolding, tools, and accessories required for a complete

working system, as per the direction of the Engineer-in-Charge.

i) NSR 26 Providing and fixing G.I. (Galvanised Iron) pipes of 100 mm nominal bore (NB),

medium class, conforming to IS:1239 (Part 1):2004, including all G.I. fittings

(elbows, tees, sockets, flanges, unions, etc.) and G.I. clamps at regular intervals

(1.8 m c/c), for internal work exposed on wall. The work shall include cutting,

threading, fixing, testing the pipe system for leakage, and making good the wall Metre 850 601.01 5,10,855.58

surface with cement mortar/plaster matching existing finish. The item shall be

completed in all respects including all tools, labour, consumables, scaffolding,

and accessories, as per the direction of the Engineer-in-Charge.

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

3.02 18.8 Providing and fixing chlorinated poly vinyl chloride (CPVC) pipes hyaving thermal

stability for hot &coldwater supply, including all CPVC plain & brass threaded

fitting, including fixing the pipewith clampsat 1 m spacing. This includesjointing of

pipes &fittingwith one step CPVC solvent cement and cost ofcutting chases and

making good the same including testing ofjoints complete as per direction

ofEngineer in Charge.

Concealed work including cutting chases and making good the walls etc.

a) 18.8.1 15mm nominal outer dia. Pipes. Metre 0 497.80 -

b) 18.8.2 20mm nominal outer dia. Pipes. Metre 1900 537.60 10,21,440.00

c) 18.8.3 25mm nominal outer dia. Pipes. Metre 1656 627.25 10,38,726.00

d) 18.8.4 32mm nominal outer dia. Pipes. Metre 1560 739.30 11,53,308.00

3.06 18.32.1 Constructing masonary chamber 30x30x50cm, inside with 7.5 class designation

brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock with

C.I. Surface box 100x100x75 mm ( inside) with hinged cover fixed in cement

concrete slab 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate 20mm

nominal size) necessary excavation foundation concrete 1:5:10 (1 cement:5 fine Each 20 1,992.60 39,852.00

sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with

cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a

floating coat of neat cement complete as per standard design with F.P.S. bricks.

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

3.11 supply, deliver, install, and test a cast‑iron circular manhole cover and frame

assembly, rated medium/light‑duty (Class C250 as per EN 124 or ASTM A‑48

Class 30), designed for a 600 mm clear opening with a 560 mm double-seal

insert, complete with locking mechanism, lifting provisions, and minimum total

weight of 116 kg. Materials must comply with IS 1726:1991 (BIS certification)

and/or equivalent international standards. Machined seating surfaces shall

prevent rocking; seals must be recessed by at least 10 mm into the frame. The

complete assembly—including primer, epoxy finish (minimum 200 µm), seals,

and locks—shall be pest-resistant, with coating certified by the designated

Municipal or Pest‑Control Authority. The epoxy and sealing components must

conform to ASTM C‑564 or equivalent, and stainless steel locking elements shall

be SS304. A sample unit shall be submitted for prior approval, followed by

submission of test certificates, load-class certification, weight declaration,

manufacturer’s drawings, & operation manual. Two sets of lifting/unlocking keys

and one spare set of seals must be provided per unit. Payment shall be made per

approved unit only after a satisfactory on-site inspection by the Engineer-in-

a) NSR 31 Medium duty double seal of size 560 mm dia and total weight of cover & frame to

be not less than 116 KG. (Location : U/G Water Tanks Top)

b) NSR 32 Light duty double seal of size 560 mm dia and total weight of cover & frame to be

not less than 116 KG. (Location : O/H Water Tanks Top)

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

3.12 NSR 33 supply, fabricate, and install sleeve-type puddle flanges constructed from hot-

dipped galvanized MS Class ‘B’ pipe, 600 mm in length, fitted with screwed ends

for diameters up to 50 mm and factory-welded flange ends for diameters

exceeding 50 mm. Each unit must include a 6 mm thick MS flange plate,

laser/punched to house the pipe, arc-welded for an airtight seal, epoxy-coated

prior to galvanizing, and further hot-dipped galvanized with a minimum zinc

coating thickness of 80 µm (as per IS 2633/GIS standards). Installation shall

include full penetration, tack-anchored to reinforcement bars within RCC tank

walls or slabs by TEC welding, with necessary shuttering cutouts provided during

concrete casting. Intended for use in both underground and overhead water

tanks, each flange assembly must be leak-tested (hydrostatic at 1.5 bar) after

installation and prior to backfilling. Contractor shall furnish mill test certificates,

coating inspection reports, weld procedure specifications, and as-built drawings

for Engineer’s approval before installation proceeds

3.13 19.16 Providing orange colour safety foot rest of minimum 6mm thick plastic

encapsulated as per IS : 10910 on12mm dia steel bar conforming to IS :1786

having minimum cross section as 23mm x 25mm and over all minimum length

263mm and width as 165mm with minimum 112mm space between protrude

legs having 2mm tread on top surface by ribbing or chequering besides

necessary and adequate anchoring projections on tail length on 138mm as per

standard drawing and suitable to with dtand the bend test and chemical Each 45 553.70 24,916.50

resistance test as per specifications and having manufacture's permanent

identification make to be visible even after fixing, including fixing in manholes

with 30x20x15cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6

graded stone aggregate 20mm nominal size) complete as per design.

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

3.14 supply, install, and commission a factory-assembled pressure-regulating station

for cold water comprising 1 no. gun-metal ball valve on the inlet, 1 no. ball valve

on the outlet and bypass, a diaphragm-type PRV with flanged connections, 2

pressure gauges (glycerin-filled, class 1.6) on inlet and outlet, and a 15 mm dia

spring-loaded safety relief valve, together with all flanges, unions, nuts, bolts,

washers, and support accessories. The complete unit shall be capable of

reducing and maintaining downstream pressure within ±0.5 bar of the set-point,

conforming to IS 9739, and shall be hydrostatically tested to a minimum of

3.0 kg/cm² prior to commissioning and shall be factory-assembled, tested and

certified, with documentation including test certificates, calibration reports, weld

procedure specs, manufacturer’s drawings, and a factory assembly certificate, all

subject to approval by the Engineer-in-Charge before site installation proceeds.

Repairs or adjustments shall be performed only by qualified personnel, with final

acceptance contingent on successful on-site function testing.

3.15 NSR supply, install, test, and commission nitrile rubber (NBR) insulation on hot water

supply piping, using premium quality elastomeric closed-cell material such as

matching the pipe outer diameter and wall thickness specified. The insulation

shall have a service temperature range of –50 °C to +105 °C (up to +110 °C for K-

Flex), thermal conductivity not exceeding 0.036 W/m·K at +25 °C, water vapor

diffusion resistance factor μ ≥5,000, and Euroclass B-s3,d0 (BS 476 Part 6/7) or

Class 0 fire rating, self-extinguishing with no dripping. Installation shall be

continuous with factory laminated or self-adhesive closures, sealed at joints and

terminations per manufacturer instructions, supported mechanically where

required, and inclusive of all adhesives, tapes, and protective coverings. Post-

installation, the insulation shall be inspected for voids, adhesion defects, and

continuity, with documentation of product batch, thickness, and conformity

certificates submitted to the Engineer-in-Charge before commissioning

NSR-49 32mm dia (9 mm thickness) Metre 90 203.34 18301

NSR-50 40mm dia (13 mm thickness) Metre 30 226.38 6791.37

NSR-51 50mm dia (13 mm thickness) Metre 30 244.41 7332.28

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

TOTAL OF SUB HEAD III - INTERNAL WATER SUPPLY 32,78,242.50 11,81,115.76

SUB HEAD V -.PUMPS, & ALIED EQUIPMENTS

5.01 Domestic Water Pump.

Providing, fixing and testing of packaged fixed drive type skid mounted

hydropneumatic system comprising of :-

Vertical, inline multistage centrifugal pumping set with stainless steel SS-304

stage casing and SS-304 impellers with stainless steel SS-316L shaft as per IEC

standards and GJL250 cast iron suction & discharge casing, connected to TEFC

ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3

phase, 50 Hz A.C. supply No. of Pumps: 3 (2 Working +1 Standby)=1 set

Control Panel with programmable logic controller (PLC) for cyclic operation of

pumps. Pump working sequence should change after every operation.Contractor

overload relays and MCBs should confirm to IEC 898 – 1995/ specifications.

Blinking indications for pumps start, trip, low level trip, health supply should be

provided in the panel along with the ammeter & voltmeter. Control panel should

also consist of cooling fan.

Pressure switches bellow type fitted with micro switch and having maximum

pressure and differential scale should confirming BS-6134 standards and IP55

protection class. Solonoid valve at terrace tank for start stop.

Stainless steel suction and delevery header, ball valve on each pump on section

delivery side, non return valves, Y stainer complete in all respect.

Ball valves to be used should be Hot Pressed brass OT-58 with stainless steel

ball and P.T.F.E seal and O-Ring. NRVs to be used should be with Springs

and O-Ring arrangement.

Complete set system to be mounted on a common base frame and shall

follow following duty.

A NSR 46 For Domestic Water Supply

Set of Three Pumps( 2 Working+ 1 Standby)

Capacity : app. 350 lpm

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

C NSR 47A Water Make up Pump to STP & Irrigation Pumps

Set of Two Pumps( 1 Working+ 1 Standby)

Capacity : app. 200 lpm

5.02 NSR 48 Drainage Sump Pumps

Submersible pumps for basement drainage & Pump Room drainage.

Submersible single stage single entry pumps with C.I.body and C.I. two vane

enclosed type impeller connected to TEFC submersible motor for 415 volts, 3

phase, 50 cycles including MCC panel with level controllers, auto control,

sequential change over facility with one proper working at low level & two proper

working at high level with an audible alarm including all interconnectivity cables,

with both pumps connected to common outlet header including valves, non return

valves, lifting chains etc. complete in all respect

B NSR 50 For Pump Room Drainage

(Solid handiling capacity 12mm)

Capacity- 200 lpm (Each)

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

3.15 NSR Supply, Installation, Testing And Commissioning of Compact Self Contained Skid

Mounted Hydropneumatic System As Follows:(A) Vertical, In-Line, Multisage,

centrifugal pumps with SS-304 casing and impeller and SS-316 shaft, CI base &

head CI material shouldbe CED coated TEFC motor (with mechanical seal) with

single VFD suitable for automatic operation and delivering the specified

discharge at the specified head,VFD should be of class IP-20 with pressure

vessel, pressure vessel should be matching of specied requirement of pump.(B)

b. External Pump mounted or wall mounted microprocessor PID controller and

frequency inverter integrated in a single body or as separate components with

pressure sensor transmitter minimum two lined LCD display, diodes to indicate

pump ready, pump running and fault and capable to communicate with other

controllers following MODBUS-RTU or BACNET Class-2 protocall through

RS485 port. System should be capable to compensate for frictional losses at

lower flows. All alarms should be displayed in the controller. System should be

equiped with dry running protection. ( C) Complete (Skid mounted wall mounted /

floor mounted) electrical control panel comprising of all accessories such as

PLCs, pressure switches, pressure transducers, control wiring and any other

necessary imports etc. (list to be provided by the vendor) (D)Precharged

diaphram pressure vessel with food grade membrane, charging connection,

connected to outlet header with necessary flanges, gaskets, isolating valves,

nuts/bolts etc complete.(E)Set of accessories such as pressure switches,

pressure transducers, inter connecting power and control cabling etc.

complete(F) Accessories like pressure gauge, MS base frame (Synthetic enamel

painted over a coat of primer)(G) GI suction and delivery header with flanges for

inlet connection, common outlet header with flanges for outlet connections as

required, and inter connecting piping with flexible connections, eccentric type

reducers etc. all necessary indigenous accessories like valves, strainer & NRV

NSR 51 Domestic Water booster Pumps at Terrace Each 1 1,65,000.00 1,65,000.00

Set of Three Pumps( 1 Working+ 1 Standby)

Capacity 200 LPM

HP 2.5 HP ( Approx.).

5.03 NSR For Water level indicators with following details:

Underground tanks

A NSR 54 Minimum 2 level Multi level indicators with magnetic type sensor probes

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

B NSR 55 Minimum 2 level Multi level indicators with magnetic type sensor probes

5.04 NSR Providing, fixing and testing of factory fitted packaged type skid mounted

pumping system comprising of :-

Horizontal inline centrifugal pumping set with CI casing and SS-304 impellers

with stainless steel SS-316L shaft as per IEC standards and GJL250 cast iron

a) suction & discharge casing, connected to TEFC ventilated induction motor of 2

pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. supply.

Motor Control Panel with DOL starter MCB and controller for cyclic operation of

pumps. Pump working sequence should change after every operation.Contractor

overload relays and MCBs should confirm to IEC 898 – 1995/ specifications.

Blinking indications for pumps start, trip, low level trip, health supply should be

b) provided in the panel along with the ammeter & voltmeter. Control panel should

also consist of cooling fan and liquid level controller with controll wiring from UG

tank to UG tank with float switch for contrlloing cut-off and cut-in of pumps and

dry run protection complete in all respects.

Suction and delivery header with Ball valves Hot Pressed brass OT-58 with

c) stainless steel ball and P.T.F.E seal and O-Ring. NRVs to be used should be

with Springs and O-Ring arrangement.

Complete set system to be mounted on a common base frame and shall

follow following duty.

5.04.1 NSR 56 Filter Feed Pump

No. of Pumps: 3(2Working + 1 Stand by )

Capacity : 100 lpm

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

Providing and fixing vertical pressure filter with dual media filter (comprising of

600mm bed depth of graded sand gravel and 600mm bed depth of Anthracite)

fabricated from high performance M.S plate of minimum 8mm thick for shell &

10mm thick for dished ends with top and bottom flanged openings including top

and bottom hub and lateral distribution and collection system complete with initial

charge of filter media, face piping, valves, accessories, painting, testing and

commissioning complete.(Tested to 6 Kg/m2)

Discharge : 100 lpm

Filtration Rate : 15000 lit./m2/h

Suggested dia app. : 0.60 m Each 2 2,79,864.00 5,59,728.00

5.06 NSR 58 Activated carbon Filter (Domestic Water)

Providing and fixing vertical activated carbon filter comprising of activated

carbon filter media fabricated from high performance M.S plate of minimum 8mm

thick for shell & 10mm thick for dished ends with top and bottom flanged

openings including top and bottom hub and lateral distribution and collection

system complete with initial charge of filter media, face piping, valves,

accessories, Epoxy painting, testing and commissioning complete.(Tested to 6

Discharge : 100 lpm

Filtration Rate : 15000 lit./m2/h

Suggested dia app. : 0.60 m Each 2 2,87,638.00 5,75,276.00

Providing, fixing, testing & commissioning of MSEP water softening plant

(suitable for 3 Kg/Sqcm working pressure) complete with initial charge with T-40

NA Resin, multiport valve with built in ejector for controlling all operations),

regeneration system and HDPE tank, pressure gauge at inlet, outlet and back

wash (each with isolation cock), valves, fittings and water hardness testing kit &

associated works. Softener shall be suitable for the following duty:

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

Note:The successful contractor will have to carry out a test of raw water from all

the sources of water for the Commercial, Residential & apartment at their own

cost from a reputed lab as approved by the Engineer-in-Charge / Consultant. On

the basis of these results the contractor has to submit his shop drawings, design

calculations and specifications accordingly.

Please note that it is ultimately the responsibility of the contractor to provide

treated water for different use as per International Standard as given in the

attached guidelines.

5.07.1 NSR 60 Raw water hardness 500 Mg/L

Treated water hardness 100 Mg/L

Regeneration Period 12 Hrs.

5.09 NSR 61 Supplying, installing, testing and commissioning of dosing system (for domestic

water treatment plant) consisting of one HDPE tank of 100 litres capacity with a

positive displacement diphragm dosing pump having variable flowrate of 0-6 lph.

The motor shall be suitable for operation at 240 V / single phase/50 Hz. Supply. Set 1 45,597.50 45,597.50

The pump shall be supplied complete with necessary polypropylene piping,

valves, strainers, low level switch and injection fittings.

The cost shall be inclusive of providing salt for the testing and operation of

system before handover to the owner.

5.10 NSR 62 Supplying, installing, testing and commissioning of annunciation and indication

panel with interlocking arrangement complete in accordance to specification for

level controller etc with control cabling from field to MCC as required. Each 1 37,973.00 37,973.00

The system shall be complete to ensure automatic operation of pump in

accordance to water level in respective tanks.

5.11 NSR 63 Providing & fixing level controllers for water pumps to start/stop the pump at set

level. Including wiring, cabling from pump to panel & all other accessories as Each 1 76,095.50 76,095.50

required to operate the system automatically.

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

5.12 NSR 64 Providing & fixing pressure switch for water pumps to start/stop the filter feed

pump at set pressure. Including wiring, cabling from pump to panel & all other Each 10 15,099.50 1,50,995.00

accessories as required to operate the system automatically.

5.13 NSR 65 Supply, installation, testing and commissioning of tanker inlet connection

complete with 100 mm dia GI (heavy) inlet piping, hose inlet connection, MS

cabinet enclosure (epoxy painted after fabriction), pad locking arrangement, inlet Each 9 14,950.00 1,34,550.00

flexible hose complete with all necessary arrangement.

TOTAL OF SUB HEAD V - PUMPS & ALIED EQUIPMENTS - 64,84,115.20

SUB HEAD VII -ELECTRICAL PANEL BOARDS FOR PHE WORKS.

7.1 NSR 115 CUBICAL PANEL BOARD - PLUMBING

i) For 2 x 3.0 HP Domestic Water fixed speed hydroneumatic Pumps (1 duty + 1 stand by)

ii) For 2 x 2 HP sump Pump (1 Duty + 1 Stand by)

Supply, installation, testing and commissioning of Cubical type sectionalised floor

standing switch board of 31 MVA fault capacity at 415 V complete with 3.5 strip,

160 A capacity Aluminium Bus - Bar Electrolytic grade, cable alley, switchgears

of following capacity & as per specifications.

100 A TP MCCB with heavy duty solid neutral link with (0-100A) ammeter with 3

CT and selector switch, (0 - 500 V) voltmeter with selector switch, phase

indication light with protection fuse. - 01 Set

i) i) For 2 x 3.0 HP Domestic Water fixed speed hydroneumatic Pumps (1 duty + 1

II) For 2 x 2 HP sump Pump (1 Duty + 1 Stand by)

40 A TP MCB with 40 A DOL starter, overload relay, 96 mm (0-40A) ammeter

with single CT, start / stop push buttons, on / off / trip indication lights with

protection fuse, single phase preventer. - 01 set.

25 A TP MCB with 25 A DOL starter, overload relay, 96 mm (0-25A) ammeter

with single CT, start / stop push buttons, on / off / trip indication lights with

protection fuse, single phase preventer. - 01 set.

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

TOTAL OF SUB HEADVII - ELECTRICAL PANEL BOARDS. - 4,48,500.00

SUB HEAD VIII RO SYSTEM

Supplying, lifting at the terrace, assembly, erection, testing and commissioning of

RO Water treatment system including centalised water cooler for cold water

provided all its components of required size as per water test analysis to make

11.1 MR 116 the water suitable for drinking, complete including the following as mentioned

below. The cost will include testing of permeate water sample from a CPCB

approved test laboratory, generating and providing membrane analysis data form

the licensed manufacturer's software etc.

Permeate water quantity = 200 lit/hr.

Minimum Recovery = 70%-75%

Raw Water Characteristics -

Raw water Quality

Total Dissolved Solids: < 990 PPM

Turbidity : <1NTU

Chlorides : 205 ppm

Sulphates : 105 ppm

Treated Water Quality

Turbidity : <1NTU

Chlorides : < 10 ppm

Sulphates : < 5 ppm

a SS Vertical centrifugal Raw Water Pump (1 Working + 1 Stand-by)

b FRP Dual Media Filter

c Activated Carbon Filter

c Antiscalant Dosing System including pump chemical dosing pump, tanks etc.

d Polypropylene Micron/cartridge Filter and SS housing

Stainless steel vertical multistage inline high pressure pump (1 Working)

including dry running protection

f Spirally wounded 6 nos. of RO Membranes

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

g Composite FRP RO pressure tube/vessel

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

Automatic RO Module Cleaning System including chemical pump, cartridge filter,

i pH correction system incl. chemical dosing pump, tanks etc.

Instrumentation including flow meters, digital TDS meter, digital pH meter,

pressure gauges, low pressure switch, high pressure switch etc. complete.

SS-316L (8 kg/cm2) piping and ABS valves for low pressure and SS-316,

schedule 10 piping and SS-316 L valves for high pressure piping in the plant.

Electrical panel including all starters, overload relays, single phase preventers,

l voltmeters, ammeters, MCB's, indicating lights, push buttons, rocker switches,

incomers, auto-manual switches etc. complete.

m All cabling , connections, terminations etc. required for the job. Each 1 2,31,725.00 2,31,725.00

TOTAL FOR SUB HEAD - XI CARRIED TO SUMMARY OF PRICES 2,31,725.00

SUBHEAD-IX: ROOF TOP SOLAR SYSTEM

8.1 NSR For Solar Water Heating System-500 LPD

Providing and fixing Solar Hot Water indirect Heating System using heating

liquid medium comprising of flat plate solar panels, including all interconnecting

insulated G.I. piping, primary and secondary recirculation pumps, pressure type

insulated hot water tank, , outlet, Y stainer and a water meter on the inlet, air

release valve all mounted on galvanized MS sections complete with connection

with the existing piping. Comparising of following:-

b) Five Nos of. flat plate solar collector panels of 10 Sqm size approx. the panels

enclosed in insulated collector boxes with single piece toughned glass 4 mm

thick and fixed with heat resistant gasket.

c) One Lot of Inter-connected insulated G.I. piping insulated with 9 mm thick nitrile

rubber heat resitant insulation sections and valves with outer mechanical

protection of aluminium sheet cladding.

8.1.1 NSR 117 Solar Water Heating System as Describe Above Set 6 88,803.00 5,32,818.00

TOTAL OF SUB HEAD IX - SOLAR SYSTEM - 5,32,818.00

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

SUBHEAD-X: WATER COOLER +RO+ UV SYSTEM

8.1 NSR For WATER COOLER +RO+UV System-150 L

a) SITC of drinking water cooler confirming to IS: 1475(Part1):2001 latest

Storage capacity- 80 Litres

MOC external body-fully SS 304, 0.5 mm thick sheet minimum

MOC water tank cover lid and bottom sheet - Al. / G.I. as per OEM and epoxy

MOC internal Storage tank- SS 304 , 0.5 mm thick sheet

Input Voltage 230 Volt , 50 Hz, AC single phase Set 10 88,803.00 8,88,030.00

Input Voltage 230 Volt , 50 Hz, AC single phase

Eco friendly refrigerant (Non CFC)

Push Type Taps - 2 nos.

Cooling capacity- 150 Ltr/Hr

b) SITC of drinking water purifier

Type of water purification technology - RO+UV

Input power voltage range - 180 - 260 VAC, 1 PH, 50 Hz.

Design value of input water TDS to the system - 2000 mg/Ltr maximum

Output water quality confirming to standard IS : 10500 ( Latest)

Type of mounting - wall mounting

Frame - stainless steel ( SS-304)

Inlet water - Normal water supply through tap ( borewell water)

High pressure pump - Copper wound booster pump as per OEM standard Set 10 88,803.00 8,88,030.00

Membrane type - 0.0001 mm RO membrane

Membrane type - 0.0001 mm RO membrane

Pre filter- As per OEM design

Carbon filter - As per OEM design

TOTAL OF SUB HEAD X - WATER COOLER +RO+UV SYSTEM 17,76,060.00

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

S.NO. DSR DESCRIPTION OF ITEMS AMOUNT

2023/NSR UNIT RATE

NBCC (INDIA) LIMITED PLUMBING WORKS Digitally signed by VARUN

BILL OF QUANTITIES FOR ELECTRICAL WORKS FOR WRPC

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S.H.-I DISTRIBUTION PANELS 50,40,330.00

S.H.-II MAIN & SUB MAIN CABLES 4,50,090.00

S.H.-III SUPPLY & FIXING OF LIGHT FIXTURES & FANS 14,47,543.00

S.H.-IV LIGHT MANAGEMENT SYSTEM 27,62,929.00

S.H.-V TELEPHONE 42,54,120.00

S.H.-VI FIRE ALARM SYSTEM 20,13,624.00

S.H.-VII UPS SYSTEM 41,40,920.00

S.H.-IX ACCESS CONTROL SYSTEM 40,32,100.00

S.H.-X DATA NETWORKING SYSTEM 38,55,950.00

S.H.-XI BOOM BARRIER SYSTEM 7,44,200.00

S.H.-XII LIGHTENING ARRESTOR SYSTEM 9,98,500.00

S.H.-XII SOLAR SYSTEM 17,50,000.00

GRAND TOTAL 3,14,90,306.00

GRAND TOTAL 3,14,90,306.00

S.H.-I DISTRIBUTION PANEL & DISTRIBUTION BOARDS-

1.1 LIFT PANEL-01 -OFFICE BUILDING

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

1 No. 200 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 150 Amp digital Ammeter with selector switch and CT's.

1 Set of phase indicating lamps with HRC fuses.

1 Set of ON/OFF indicating lamps with HRC fuses.

300 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.

05 Nos. 63 Amp TP+N Moulded Case Circuit Breaker.

06 Nos. 40 Amp DP Miniature Circuit Breaker.

02 Nos. 40 Amp TPN Miniature Circuit Breaker.

01 Nos. 63 Amp TPN Miniature Circuit Breaker.

Panel described as above Set 1 1,52,817.00 1,52,817.00

1.1 LIFT PANEL-02-GUEST HOUSE BUILDING

1 No. 100 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 150 Amp digital Ammeter with selector switch and CT's.

1 Set of phase indicating lamps with HRC fuses.

1 Set of ON/OFF indicating lamps with HRC fuses.

150 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.

04 Nos. 63 Amp TP+N Moulded Case Circuit Breaker.

06 Nos. 40 Amp DP Miniature Circuit Breaker.

02 Nos. 40 Amp TPN Miniature Circuit Breaker.

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

01 Nos. 63 Amp TPN Miniature Circuit Breaker.

Panel described as above Set 1 1,27,547.00 1,27,547.00

1 No. 63 Amp TPN Miniature Circuit Breaker.

100Amp TPN copper busbar.

01 No. 63 Amp FP RCBO.

02 Nos. 40 Amp DP Miniature Circuit Breaker.

Panel described as above Set 6 18,753.00 1,12,518.00

1.3 TYP FLOOR PANEL-

1 No. 160 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 100 Amp digital Ammeter with selector switch and CT's.

1Set of phase indicating lamps with HRC fuses.

1Set of ON/OFF indicating lamps with HRC fuses.

200Amp TPN aluminium busbar with coloured heat shrinkable sleeve.

02 Nos. 100 Amp TP+N Moulded Case Circuit Breaker.

02 Nos. 40 Amp DP Miniature Circuit Breaker.

03 Nos. 25 Amp DP Miniature Circuit Breaker.

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

Panel described as above Set 12 88,445.00 10,61,340.00

1.16 VENTILATION PANEL -

1 No. 200 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 200 Amp digital Ammeter with selector switch and CT's.

1Set of phase indicating lamps with HRC fuses.

1Set of ON/OFF indicating lamps with HRC fuses.

315 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.

20 Nos. 40 Amp TP+N Moulded Case Circuit Breaker.

Panel described as above Set 2 3,63,489.00 7,26,978.00

1.17 INVERTER PANEL - 1 & 2

1 No. 63 Amp FP Moulded Case Circuit Breaker.

1 No.0 to 500 Volt digital voltmeter with selector switch.

1 No.0 to 100 Amp digital Ammeter with selector switch and CT's.

1Set of phase indicating lamps with HRC fuses.

1Set of ON/OFF indicating lamps with HRC fuses.

150Amp TPN aluminium busbar with coloured heat shrinkable sleeve.

02 Nos. 63 Amp DP Miniature Circuit Breaker.

Panel described as above Set 2 37,772.00 75,544.00

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

1.18 MCCB BOX WITH MCCB (INCOMMING/OUTGOING)

INCOMING/OUTGOING

1 No. 63 Amp FP Moulded Case Circuit Breaker.

Panel described as above Set 6 17,556.00 1,05,336.00

2.0 RISING MAINS

Design, Manufacture, Supply, Installation, Testing, and Commissioning of

Sandwich type 1100 volts rising mains with cooling Fins, 4bar - 3P & 1N,

Aluminum conductor with aluminium body / powder coated sheet steel

enslosure with earth throughout the continuous length, as per specification,

suitable for 3ph 4wire 50HZ, of short circuit fault withstand capacity, for 1 Sec

as specified below.The busway shall have a system for plug in tap off box at

desired levels and single bolt double head section jointing system including

vertical & straight joints. The Tap off boxes shall have Door Interlocking

mechanism and mechanical interlocking with Bus duct housing during ‘ON’

position to prevent being taking of in energized condition. Supporting system

shall be fail proof even in the earth quake situations, as per sesmic

requirement of site.

i. For Rising Mains, no temperature deration upto 45°C Ambient temperature.

ii. Flexible connections need to be included and need to be provided as

required for thermal expansion/ building expansion joints / panel end

connections /one vertical expansion for every floor.

iii. 100% sized Neutral as of phase current to be provided.

3 Cable feed end unit (Adoptor Box) with 4 Pole, MCCB 50 KA, with thermal

based inbuit O/C, S/C & E/F releases with suitable cable termination

arrangement. (For incoming cable connection) . (IP54)

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering &

indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of

the panel on the primary side of PT & suitable rated 6A, TP MCB on the

secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable

1 No. Digital VAF + PF Meter (110V) (With RS 485 Port)

1 No. Digital Energy Meter (KWH) (With RS 485 Port)

4.0 End Cap at top (at last floor) (IP54) Nos 2 12,635.00 25,270.00

5.0 TAP OFF UNIT-

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, Installation,

Testing & Commissioning of cubical type tap off unit box fabricated out of 2.0

mm thick CRCA sheet, dust and vermin proof, with hinged detachable doors

and painted front, comprising LED type indication lamps with toggle switches

and 4 pole MCCB terminated directly with tap off box with Bus Bar links on the

incoming side and suitable for cable connection on the outgoing side including

making connections, interconnections, earthing complete as required. All

MCCB shall have Ics value of 36 KA and Thermal Magnetc release for over

current & short circuit.

5.1 Tap Off Box with 100 Amp FP MCCB. Set 4 12,430.00 49,720.00

5.2 Tap Off Box with 160 Amp FP MCCB. Set 10 18,018.00 1,80,180.00

6.0 UPS INPUT PANEL (INDOOR TYPE)-

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

Manufacturing, supply, receipt, unloading, shifting, installation, testing, and

commissioning of a cubicle‑type, totally enclosed, free‑standing,

moisture‑, dust‑ and vermin‑proof Floor Distribution Panel fabricated from

high-quality CRCA sheet steel. The panel body shall be made from 2.0 mm

thick CRCA, with the front cover made of 1.6 mm thick CRCA, exhibiting

robust construction and surface finish. The enclosure shall conform to at least

IP‑42 protection rating (or higher such as IP‑51/IP‑54 where applicable) for

ingress protection per IS standards and be gasketted at all joints using

neoprene or synthetic rubber seals to ensure dust and vermin tightness

The panel design shall include compartmentalization to isolate busbars,

metering units, CT chambers, and outgoing feeders, minimizing arc

propagation and ensuring maintenance safety. The enclosure must be free-

standing, floor-mounted with a sturdy internal base frame, lifting lugs, and

reinforcement to resist warping or vibration during installation and operation

Integral to the FDP, the following equipment shall be provided: digital

ammeter with built‑in ammeter selector switch, digital voltmeter with

built‑in voltmeter selector switch, phase indicating lamps, CT units, and

all internal wiring using suitable-size copper cables, interconnections, and

terminal blocks. Wiring conductors must be 110 V PVC insulated copper wire

(≥1.5 sq mm for control and ≥2.5 sq mm for CT/instrument circuits), color-

coded and ferruled at both ends. All components shall be flush-panel

mounted, accessible without exposing live parts, and compliant with

serviceability requirements

Busbars shall be sized as per electrical load, supported on non-hygroscopic

insulators, and enclosed in separate vermin-proof compartments with bolted

steel covers. Phase busbars shall be color-coded and insulated, with joints

adequately tinned and bolted to handle thermal and short-circuit stresses.

Neutral and earth busbars shall be separate but similarly supported and

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

The entire assembly shall undergo factory finish using seven‑tank

passivation followed by powder coating or epoxy paint (light admiral grey,

IS‑5 shade) to achieve uniform coverage, rust resistance, and a dent-free

aesthetic appearance

Pre‑commissioning and testing shall cover insulation resistance tests,

continuity checks, metering accuracy verification, torque checks, and

operational integrity verification of selector switches and indicators. The

Contractor shall submit full test certificates, wiring diagrams, layout drawings,

and commissioning reports as per specifications and approved drawings.

1 No. 800 Amp FP ( 35 KA Ics) Moulded Case Circuit Breaker.

1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.

1 No. 800 Amp digital ammeter with inbuilt selector switch and CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

1 Set 24 Hrs TSQ Timer

1 Set 63 Amp, 4P Contactor & A/M switch and Push Button.

1000 Amp TPN aluminium busbar.

04 No. 250 Amp TPN MCCB.

2 No. 250 Amp TPN MCCB FOR SPARE

Panel described as above Set 1 3,02,176.00 3,02,176.00

6.0 UPS OUTPUT PANEL (INDOOR TYPE)-

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

DesignB374:AC374, Manufacturing, Supply, Receiving, Unloading, Shifting,

installation, testing & commissioning of cubicle type totally enclosed free

standing type moisture, dust and vermin proof Floor Distribution Panel made

out of 2.0 mm thick & front cover 1.6 mm thick CRCA sheet complete with

following equipments, including digital ammeter with inbuilt ammeter selector

switch, digital voltmeter with inbuilt voltmeter selector switch, indicating lamps,

CT's, internal wiring with suitable size wires / cable, interconnection, painting

complete as per specification & drawing.

2 No. 250 Amp FP ( 35 KA Ics) Moulded Case Circuit Breaker.

1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.

1 No. 800 Amp digital ammeter with inbuilt selector switch and CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

1 Set 24 Hrs TSQ Timer

1 Set 63 Amp, 4P Contactor & A/M switch and Push Button.

500 Amp TPN aluminium busbar.

12 No. 63 Amp TPN MCCB.

2 No. 40 Amp TPN MCB FOR SPARE

2 No. 32 Amp TPN MCB FOR SPARE

Panel described as above Set 1 2,92,999.00 2,92,999.00

TOTAL OF DISTRIBUTION PANEL CARRIED OVER TO SUMMERY 50,40,330.00

S.H.-II MAIN & SUB MAIN CABLES

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

1.0 Supply of following sizes of 1.1KV grade multicore aluminium conductor XLPE

insulated and PVC sheathed armoured cable conforming to relevant IS

(Cable shall be purchased only after approval of cable schedule by architect /

2.0 Supply & Laying of following sizes of 1.1KV grade multistranded copper

conductor PVC insulated cable including termination complete as required in

existing cable tray.

2.1 1Cx16 sq.mm PVC Insulated cu wire including termination etc. for UPS Meter 250 86.00 21,500.00

neutral earthing and UPS.

2.2 1Cx35 sq.mm PVC Insulated cu wire including termination etc. for D.G. Meter 250 188.00 47,000.00

neutral earthing

TOTAL OF MAIN & SUB MAIN CABLES CARRIED OVER TO SUMMERY 4,50,090.00

S.H-III SUPPLY & FIXING OF LIGHT FIXTURES & FANS INTERNAL LIGHTING-

1.0 Supply, Installation, Testing & Commissioning of 1x22 Watt LED Light Fixture Each 10 948.00 9,480.00

surface mounted as per technical specification.

2.0 Supply, Installation, Testing & Commissioning of 10 W Surface Mounted LED Each 350 2,007.00 7,02,450.00

3.0 Supply, Installation, Testing & Commissioning of 15 W Recess Mounted LED Each 80 2,727.00 2,18,160.00

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

4.0 Supply, Installation, Testing & Commissioning of 1x10 Watt LED Light Fixture Each 40 686.00 27,440.00

surface mounted as per technical specification.

5.0 Supply, Installation, Testing & Commissioning of Light Fixture surface Each 75 1,089.00 81,675.00

6.0 Supply, Installation, Testing & Commissioning of GARRNET 12W LED BULB Each 25 1,289.00 32,225.00

suitable for batten holder.

7.0 Supply, Installation, Testing & Commissioning of Bracket Light Fixture Each 25 1,463.00 36,575.00

surface mounted.

8.0 Supply of following sizes of heavy duty exhaust fan for single phase 230

volt, 50HZ AC supply complete with motor, blades, frame, bracket, louver/

shutter etc as required.

9.0 Supply of following sizes of ceiling fan complete with double ball bearing,

motor, blades, downrod, canopy, capacitor etc. suitable for operation on 230

volt, 50 Hz, A.C. supply complete as required.

10.0 Supplying Installation, Testing & Commissioning of 70 W CDM-T (Surface Each 6 6,611.00 39,666.00

Type) Cylindrical downlight with high efficiency glossy reflector for better light

distribution complete with elctronic gear, lamp complete etc as required.

11.0 Supply & installation of 32 Amp single phase 240 Volt, 50 Hz, industrial socket Each 22 1,885.00 41,470.00

outlet with SP MCB complete with all the fixing accessories as below.

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

12.0 Supply, Installation, Testing & Commissioning of Integral LED aviation light Each 3 11,854.00 35,562.00

comprising of aluminium housing with polycarbonate enclosure with flasher

suitable for 230V AC complete with fitting including photochromatic switch for

automatic ON/OFF of Aviation lights complete

TOTAL OF LIGHT FIXTURES & FANS CARRIED OVER TO SUMMERY 14,57,023.00

S.H-IV SUPPLY & FIXING OF LIGHT MANAGEMENT SYSTEM LIGHTING-

1.0 SITC of 1 Channel wired KNX Dali Gateway - interface between DALI & wired NOS 1 78,470.00 78,470.00

system installation. Control & status data, Control of up to 1*64 DALI devices

in up to 1*16 groups, Setting the colour temperature for luminaires with DALI

Device Type 8 for Tunable White in accordance with IEC 62386-209. Suitable

for operation in emergency lighting systems Individual, group or central

addressing - 2*16 light scenes - Effect control for dynamic lighting effects or

colour change. Support of DALi part 252

2 SITC of 2 Channel wired KNX Dali Gateway - interface between DALI & wired NOS 2 1,08,289.00 2,16,578.00

system installation. Control & status data, Control of up to 2*64 DALI devices

in up to 2*16 groups, Setting the colour temperature for luminaires with DALI

Device Type 8 for Tunable White in accordance with IEC 62386-209. Suitable

for operation in emergency lighting systems Individual, group or central

addressing - 2*16 light scenes - Effect control for dynamic lighting effects or

colour change. Support of DALi part 252

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

3 SITC of 4 Channel - mutlti operation relay, with each 16A channel with high- NOS 4 42,362.00 1,69,448.00

inrush current capacity of 80A/20 ms. With detachable KNX programmable

upper module which can be fixed post the installation of the lower relay unit. 4

different channel functions can be selected: - Switching, ON/OFF Delay,

Pulse function, Staircase light timer with switch-off pre-warning. Possible

integration of the channels into a maximum of 8 scenes. Adjustable response

to bus failure and restoration of the bus/mains power. Logical functions.

4 SITC of BUS Power Supply, 640mA Power Supply. For supplying power to NOS 3 59,637.00 1,78,911.00

other Bus devices with bus voltage. One non-choked and one choked output

each. The non-choked output can be used for the supply of another line or for

function devices (smart sensor etc.) which require an auxiliary voltage.

Nominal voltage can be subdivided to outputs (choked or nonchoked) as

desired. With reset switch for bus lines. With short circuit protection. With

overvoltage protection.

5 SITC Of bus sytem to IP Router/Interface/Gateway, Connecting IP with TP 0 3 61,950.00 1,85,850.00

Bus system Supporting routing and tunneling functions Indicated operation

and filtering statuses by LEDs Connecting Bus IP/other devices by a standard

RJ45 connector directly and also via Ethernet networks A rail-mounted device

for installation in distribution boards on 35 mm DIN rails Integrated bootloader

function for remote firmware updates via IP / Ethernet Temporary deactivation

of filtering by a single button press (Eases commissioning because of short-

time access to other lines.) No need for an additional power supply

7 SITC of Standalone Ceiling Mount PIR Sensor having range of 6 meter at NOS 10 27,465.00 2,74,650.00

height of 2.5-3.5 meter, For switching lighting systems that depend on

brightness and movement. Ceiling installation using integrated spring bracket.

Switch-off delay: approx. 1 sec - 15 min or short-time pulse adjustable

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

8 SITC of Network protocol for operating switching, dimming, blinds and NOS 4 25,895.00 1,03,580.00

recall/save light scene functions individually. 8 Button operation. Can be used

to set/send temperature, priority, value, percentage, HVAC operation mode

value. Scene functions can be saved by pressing 5 seconds if fold/hold is

programmed as recall/save light scene. Setting of desired behaviour via long

and short key depression is possible. With LED status indication

9 Providing, installing, testing and commissioning of Graphical Software NOS 1 7,06,230.00 7,06,230.00

providing the facility to create / provide the following, static and animate the

Graphics, Navigation between pages, display of logs, changing the time

zones, popup alarms, with Unlimited number of user license configurable

password protection for Building Automation System as per Specifications.

The BMS platform shall natively support standard communication protocols

such as BACnet™/Modbus / KNX/ MQTT/OPC UA/REST API /SNMP etc. The

Software should be capable enough to transmit messages on Email Alerts.

The software should be Web Based Software .

This Software should have the following Key features

1. WEB BASED TOOL for remote engineering.

2. EMAIL / SMS OPTION AVAILABLE

3. MULTIPLE DATABASE SOURCES / SITE CAN BE INTEGRATED.

4. Capable of connecting with Cloud Platforms over E2C.

5. Integrated/customized widgets for energy analytics and Lighting Controls

6. Scalable vector graphics, customized graphics

7. Project haystack tagging convention

8. All should be completed as per tender specification.

9. Ready for Voice AI based building conversationAll should be completed as

per tender specification.

10. Software shall have the capacity to accommodate 2000 points

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

10 BMS Work System: Providing, installing, testing and commissioning of server NOS 1 2,51,104.00 2,51,104.00

grade Pentium i7 Core with 3GHz minimum CPU speed, minimum of 16 GB

RAM, 512 KB cache, 2GB Graphics card & 1 TB HDD, optical Mouse, 106

keys keyboard, 10/100/1000 Mbps Ethernet card ,USB connection & internal

modem, - I7 Processor (Latest ) ; 16 GB RAM, 1 TB hard disc ; 32” flat

screen, 1200 2 800, 256 colours (Full HD) ; Windows 11 Pro (Professional)

and shall have Licence MS-Office installed

11 SITC of DALI wire 1.5 sqmm FRLS NOS 250 235.00 58,750.00

12 SITC of KNX Wire 4 core 2*2*0.8 sqmm NOS 410 282.00 1,15,620.00

13 SITC of Automation DB with Incoming Protection Devices NOS 9 47,082.00 4,23,738.00

TOTAL OF LIGHT MANAGEMENT SYSTEM CARRIED OVER TO 27,62,929.00

S.H.-V IP-PBX SYSTEM

1 Supply, Installation, Testing & Commissioning of Pure IP at core server Set. 1 20,25,000.00 20,25,000.00

Based voice solution with 04 Port Voicemail ,04 Port FXS ,04 Port FXO ,1

PRI Trunk lines (30 Ch) Circuit with CLIP Facility ,120 IP users License ,01

Nos. IP Operator Console, 100 Party Conference ,Speed Dial, Music on Hold ,

2 Internal/ External ring

Supply, Installation, difference

Testing ,Call Barring, Call

and Commissioning of Pickup, TEC should

Type 1 Phone be

inch Color screen (300x220 pixel), 3 VoIP account, 4 soft keys,3 one touch

keys with LED indication, Dual port Gigabit Ethernet, PoE,

TOTAL OF IP-PBX SYSTEM CARRIED OVER TO SUMMERY 42,54,120.00

VI FIRE ALARM SYSTEM-

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

1.0 Supply, Installation, Testing & Commisioning of Microprocessor based X loop

fire alarm control panel expandable upto 10 loops fully networkable with each

loop capable of taking 125 devices, 8 line x 40 character alpha-numeric liquid

crystal display. The panel shall be soft addressable type. The panel shall be

able to give pin point location of all fire/fault conditions. Further, the panel

must be able to automatically switch off respective control switches when ever

any alarm is triggered. The panel shall have in built rectifier, Loop

cards,provision for externel & internal printer (if required), LCD unit to

indicate Fire/Fault Signal with address and analog output, built in printer to log

all fire or fault events complete in all respects, integral SMF lead acid batteries

with sealed cells of 24 V capable of running for a minimum of 8 hours with

integral battery charger complete as required and as per specification. The

fire alarm panel shall be suitable for software integration with BMS & PA

2.0 Supply, Installation,Testing & Commisioning of Analog Addressable Intelligent Nos. 110 4,150.00 4,56,500.00

multisensor detector with two inbuilt optical smoke sensors with light angles

as well as additional heat detector sensor with decentralise intelligence, soft

addressable Photothermal type with inbuilt fault isolator as per NFPA style 7

wiring complete with base as required.

3.0 Supply Installation, Testing & Commissioning of Intelligent addressable Nos. 14 6,115.00 85,610.00

Manual Call Point / Pull station complete as per specification.

4.0 Supply, installation, testing and commissioning of addressable control module Nos. 16 5,606.00 89,696.00

complete as per specification.

5.0 Supply, installation, testing and commissioning of addressable monitor Nos. 16 5,679.00 90,864.00

module complete as per specification.

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

6.0 Supply Installation, Testing & Commissioning of wall mounting loop powered Nos. 16 9,464.00 1,51,424.00

addressable type hooter with all accessories.

7.0 Supply Installation, Testing & Commissioning of Response Indicator single Nos. 16 182.00 2,912.00

8.0 Supply, Installation, Testing & Commisioning of Analogue Addressable Nos. 2 4,076.00 8,152.00

Intelligent Heat Detector with fixed & rate of rise temperature function with

decentralise intelligence , soft addressable type, with inbuilt fault isolator as

per NFPA style 7 wiring complete with base as required.

9.0 Supply, Installation,Testing & Commisioning of Networkable Repeater Panel Nos. 2 1,31,048.00 2,62,096.00

(LCD indicator panel) with 2 line X 20 characters alpha numeric LCD display

with all commands such as reset, mute, silence with suitable battery backup

complete as required.

TOTAL OF FIRE ALARM SYSTEM CARRIED OVER TO SUMMERY 20,13,624.00

S.H.-VIII UPS SYSTEM

1.0 Supply, installation, testing, and commissioning of a 120 kVA true on-line

double-conversion UPS, fully configured for parallel operation, and

equipped with an SNMP card for network monitoring. The UPS must ensure

input current THD ≤ 3% across the entire load range, and maintain an input

power factor ≥ 0.95 between 25% and 100% load, with optimal operation at

≥0.99 PF at full load—features routinely delivered by top-tier models like

Delta DPH‑120K (Modulon), Eaton 93E‑120K, Vertiv Liebert Hipulse‑U

120K, or Riello Sentryum 120K.

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

The equipment shall deliver rated output at ambient temperatures up to 40 °C

and feature a soft-start mechanism to smoothly engage incoming power

sources under varying line conditions.

The UPS inverter must be capable of supporting a 150% overload for a

minimum of 5 seconds, affording short-duration resilience during sudden

load surges. Power configuration shall include three-phase input (340–470 V

AC, 4‑wire) and three-phase output (400–415 V AC, 4‑wire). Battery

management shall prevent deep discharge, ensuring the battery voltage

remains above 10.5 V per 12 V cell. External, rack-mounted SMF batteries

capable of delivering at least 30 minutes of backup at 100% load shall be

The system must support parallel synchronization of all UPS units, and the

parallel operation kit (including synchronization modules and bus bars) must

be provided. The UPS shall be equipped with remote communication

interfaces for integration into building management or network monitoring

All standard protection features—such as overcurrent, inverter fault, thermal

cut-off, surge protection, and battery safety—must be integrated. Pre-

commissioning tests shall include THDi/THDv measurement, power factor

validation, overload recovery, battery discharge protection validation, and

synchronization checks. Final commissioning must align with approved

documentation and shall include full test reports, configuration settings,

drawings, and load runtime validation results

UPS described as above Nos. 2 11,50,230.00 23,00,460.00

2.0 supply, installation, testing, commissioning, and integration of a 60 kVA

true on‑line double‑conversion UPS, designed with parallel operation

capability for up to four units and inclusive of the required parallel

synchronization kit. The UPS must offer a total harmonic distortion of

input current (THDi) below 3% across the entire load range and maintain an

input power factor ≥ 0.95 from 25% to 100% load, with typical operation

exceeding 0.99 at full load, as exemplified by industry-standard systems

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

It shall be rated to deliver full output at ambient temperatures up to 40 °C and

include a soft-start feature to reduce stress on incoming supply sources.

The UPS’s inverter must support 150% overload capability for at least 5

seconds, allowing it to sustain short-term load peaks. It shall accept a three-

phase input voltage range of 340–470 V AC (3P, 4-wire) and deliver

regulated three-phase output at 400–415 V AC (3P, 4-wire). Battery

management must prevent deep discharge; battery voltage must not drop

below 10.5 V per 12 V cell, and external rack-mounted SMF batteries must

be provided to guarantee a minimum of 30-minute backup at full load.

The system must support parallel synchronization of all UPS units, and the

parallel operation kit (synchronization modules, busbar connectors) must be

included. A standard SNMP communication card shall be provided to enable

remote monitoring and integration with facility management systems.

All operational protections—including overcurrent, inverter fault alarm, thermal

shutdown, bypass switching, and battery safety—must be built into the

system. Prior to commissioning, the Contractor shall conduct performance

tests such as measuring THDi/THDv, validating input power factor across

load ranges, verifying overload recovery, conducting battery discharge

protection tests, and confirming seamless synchronization in parallel mode.

Final commissioning must conform to approved documentation, and the

Contractor must furnish detailed test reports, configuration settings, wiring

diagrams, and runtime validation results

UPS described as above Nos. 2 9,20,230.00 18,40,460.00

TOTAL OF UPS SYSTEM CARRIED OVER TO SUMMARY 23,00,460.00

S.H.-X ACCESS CONTROL SYSTEM

3.0 Access Intelligent Controllers (AIC)

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

supply, installation, testing, and commissioning of an intelligent access Nos 1 1,72,500.00 1,72,500.00

control controller with support for 4 Wiegand-standard readers or up to 8

serial RS‑485 interfaces, fulfilling specifications such as 8 programmable

input & 8 relay output ports, housed in a robust, field-grade enclosure. The

unit must include an AC/DC power supply and maintenance-free batteries

providing minimum 30 minutes backup

The controller shall incorporate a minimum 32‑bit embedded

microprocessor, onboard TCP/IP networking, and at least 2 GB flash

memory, capable of storing 2,000 user access profiles and caching 4,000

offline transactions. A 16-character LCD display with navigation keys shall

indicate system status, including IP address, MAC address, network health,

and diagnostic parameters. The unit should carry certifications such as

UL 294, FCC, CE, EN compliance.

4.0 Readers , Cards & Tags

4.1 Supply, installation, testing, and commissioning of biometric fingerprint Nos 10 20,700.00 2,07,000.00

readers with integrated smart‑card support and PIN pad at each secured

access door, offering a read range of up to 9 cm and conforming fully with the

project specification. Each unit shall support fingerprint + smart‑card + PIN

authentication workflows, with robust anti‑spoof capabilities and real‑time

validation. The devices must interface via at least Wiegand protocol,

support TCP/IP or RS‑485 connectivity, and offer expandable network options

for centralized access management. Power backup is mandated via

maintenance-free batteries sustaining operations for 30 minutes during

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

Controllers/readers shall incorporate a minimum 32‑bit embedded

processor, 2 GB flash memory, and onboard TCP/IP; they must store at least

2,000 user profiles and buffer 4,000 transactions in offline mode. A 16-

character LCD display shall provide key diagnostics—displaying controller

IP, MAC address, and system status at the panel. The devices must hold

global certifications such as UL 294, FCC, CE, and EN compliance to ensure

security and quality.

4.2 Supply, install, test, and commission contactless smart-card readers with a Nos 12 9,200.00 1,10,400.00

read range of up to 4 cm, to be deployed at every secured entry door as per

project requirements. Each reader shall support standard Wiegand output

(WG26/WG34) or RS‑485 interface, powered via 12 V DC with robust internal

filtering and surge protection. The device shall be housed in a sturdy

enclosure suitable for indoor or semi-outdoor use with IP54 rating, and

operate reliably within a temperature range of –20 °C to +70 °C per installation

requirement. The reader shall feature at least 32‑bit embedded

microprocessor, onboard TCP/IP or RS‑485 communication, and flash

memory capable of local buffering for offline authentication during

connectivity loss.

4.3 Supply, install, test, and commission high‑security contactless smart cards Nos 50 575.00 28,750.00

featuring 16 K byte memory segmented into 16 application areas,

compliant with ISO/IEC 14443 standards, for use across access control

devices including boom barriers, turnstiles, flap barriers, biometric readers,

and secured doors. These cards must support multi-application credential

storage, mutual authentication between card and reader, and encrypted data

transfer consistent with HID iCLASS SR 16K/16 technology—the industry

5.0 Access Control & Attendance Software

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

Supply, install, test, and commission a fully integrated Access Control Nos 1 3,27,750.00 3,27,750.00

System server software package comprising enterprise-grade access

control, visitor management, and attendance modules, along with four

client-seat licenses, all configured as per project specifications. This system

must support centralized configuration of access rules, audit trail generation,

visitor pre-registration and badge issuance, attendance tracking, and

integration with physical access devices. The software should offer a scalable

client–server architecture, supporting over tens of thousands of credentials

and transactions, compatible with SQL/Oracle backend databases, and

accessible via 4 client workstations concurrently.

6.0 Misc Other Items for Access Control System :

6.1 Supply, installation, testing, and commissioning of a single‑leaf Nos 10 8,625.00 86,250.00

electromagnetic lock with a minimum holding force of 600 lbs (≈280 kg),

compliant with project specifications. The lock assembly must include a robust

armature plate, anodized aluminum or stainless steel body, internal MOV

surge protection, LED feedback indicator, and fail-safe (power‑fail unlock)

operation. The lock should support door alignment compensation

mechanisms to prevent residual magnetism and door jamming. Installation

shall include all required brackets (L/Z/U type), power supply wiring, and

bonding sensors if specified.

6.2 SITC of a double‑leaf electromagnetic lock with a minimum holding force Nos 10 11,500.00 1,15,000.00

of 600 lbs (approx. 280 kg × 2), suitable for double-swing doors in access

control setups. The lock assembly shall be constructed from anodized

aluminum alloy, feature internal MOV surge protection, built-in LED status

indicators, and fail-safe operation (unlock on power-off). The system shall

include reliable armature plates, L/Z/U mounting brackets, and optional door-

position feedback. The device must support dual-voltage operation (12 VDC /

24 VDC), draw not more than 500 mA per coil, and operate reliably between

−10 °C to 55 °C and up to 95% non-condensing humidity

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

6.3 Supply, install, test, and commission flush‑mounted exit push button Nos 20 1,725.00 34,500.00

switches at every designated exit point in the access control system, in

accordance with project specifications. Each device must be spring-loaded,

momentary‑push type with both NO and NC (SPDT) contacts, rated for

12–36 VDC at 3–5 A, mechanically rated for at least 1,000,000 actuations,

and housed in a stainless-steel or aluminum faceplate (standard 86 × 86 mm

or 76 × 76 mm) with bevelled edges and optional LED indication. The output

wiring shall be compatible with standard Wiegand/lock-release controllers

and engineered to prevent false triggering due to EMI or moisture ingress.

The exit button plate should be fire-rated, surface-flush or standard wall-box

mounted, and meet ingress protection up to IP54 for resilience in commercial

6.4 Supply, lay, test, and commission 8-core, 0.5 sq mm multi-strand copper, Mtrs 250 242.00 60,500.00

shielded instrumentation cable (with overall aluminum-mylar screening and

drain wire) between each card reader and its access controller, as per

specification. This cable must be Flame-Retardant Low Smoke (FRLS) rated,

PVC insulated, flexible class‑5 stranded conductor, UV-rated sheath for

indoor installation, with overall foil shielding and long-term mechanical

flexibility. It shall comply with standards such as EN 50288‑7 or equivalent,

and operate reliably at up to 300/500 V AC.

6.5 Supply, lay, test, and commission 2-core, 1.5 sq mm multi-strand copper Mtrs 150 219.00 32,850.00

sheathed instrumentation cable with overall aluminium-mylar shield and

drain wire, as specified—intended for wiring between access controllers and

EM locks, door sensors, or request-to-exit push buttons. The cable shall be

FRLS PVC‑insulated, flexible (Class‑5 conductor), unarmoured, with overall

shielding to prevent EMI interference, rated for 300/500 V, and manufactured

per EN 50288‑7 or equivalent standards. The sheath must be UV-resistant

and suitable for indoor installations

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

TOTAL OF ACCESS CONTROL SYSTEM CARRIED OVER TO SUMMARY 11,75,500.00

XI Data Networking

1 deliver, install, test, and commission one or more units of Cyberack 42U × Nos 5 73,150.00 3,65,750.00

600 mm width × 800 mm depth networking rack enclosure, built with

CRCA steel end‑frames and aluminium profile pillars, capable of

supporting a static load of up to 500 kg, and furnished with two removable

side panels, a vented top cover with cable-entry, bottom cover with

cable-entry, dual pairs of 19-inch adjustable mounting angles, powder-

coated finish (80 µm matt black), a vented glass front door, and

full‑perforated steel rear door with lock. Included accessories shall

comprise: one 10 × 5 / 15 A PDU, fan housing unit with four pre-wired

cooling fans, one set of mounting hardware (20-pin), 2 castors with

brake + 2 without brake, one earthing kit, two 1U 19-inch cable

managers, and all requisite fasteners and accessories

2 Supply, install, terminate, test, and commission a loaded 48‑port Cat‑6 UTP Nos 10 17,250.00 1,72,500.00

keystone patch panel, designed to mount in a standard 19‑inch rack

occupying 1U (or 2U if so specified). Each port shall support 568A/B wiring,

routed via 110 IDC punch‑down blocks, with keystone jacks compliant with

Cat‑6 specification. The panel body shall be constructed of durable metal,

powder-coated matte black, and feature rear cable management bar or

lacing bars, numbered port labeling front and back, and low-profile mounting

brackets as per structured cabling best practices

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

3 Supply, install, test, and commission a 48‑port PoE+ access switch with a Nos 15 1,43,750.00 21,56,250.00

minimum switching capacity of 12 Gbps, forwarding performance

≥ 95 Mpps, and configured with 24 or 48×10/100/1000 BASE-T PoE+ RJ45

ports, delivering a minimum PoE power budget of 370 W, plus 4×10G SFP+

uplink ports, per specification. The switch must support static routing and

IPv6 multicast routing (≥1,000 routes) from day one and include at least

2 GB of internal DRAM, 2 GB flash memory, and a MAC address table

capacity of ≈32 K entries. A 1‑year support warranty shall be included.

4 SITC tool‑less Cat 6 RJ‑45 keystone outlets—either flush-mounted or Nos 250 350.00 87,500.00

surface-mounted—with matching faceplates and pre‑installed back boxes for

each computer access point. The outlets must feature tool‑free termination

technology (no punch-down tool required), conform to ANSI/TIA‑568 A/B

standards, and support speeds up to 1 Gbps. The keystone jacks must be

Cat 6 standard, termination color-coded for both T568A and B wiring

schemes, with robust insertion retention mechanisms. Faceplates shall be

modular, mount on standard electrical boxes or surface boxes, and be ABS

plastic or equivalent flame-retardant material. Back boxes should

accommodate standard wall apertures and facilitate neat cable management.

5 Supply, lay, test, and commission 1 metre long, Cat 6 UTP patch cords, fully Nos 250 290.00 72,500.00

compatible with 1 Gbps LAN infrastructure at all networking endpoints. Each

patch cable must be constructed from stranded 24 AWG copper conductors,

PVC jacketed or optionally LSZH, fitted with gold-plated RJ45 plugs and fully

compliant with ANSI/TIA‑568‑C.2 standards and capable of supporting up to

10 Gbps data rates over short distances. The patch cord assemblies shall

feature molded snagless boots and strain relief, and each unit must be

factory‑tested to guarantee performance and low insertion loss

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

6 Supply, install, test, and commission factory‑tested 2 metre Cat 6 UTP Nos 400 230.00 92,000.00

patch cords (stranded, 24 AWG), for desktop computer or network device

connectivity, featuring gold‑plated RJ‑45 connectors, molded snagless boots

with strain relief, and full compliance with ANSI/TIA‑568‑C.2 standards. Each

cable shall support up to 10 Gbps data transmission, be capable of over 750

mate/demate cycles, and possess UL, CE, and FCC certifications where

applicable. Cables shall operate reliably as part of structured LAN

infrastructure, ensuring minimal attenuation and solid performance

7 Supply, lay, test, and commission 4‑pair Cat 6 UTP solid‑core LAN cable Mtrs 1500 30.00 45,000.00

made from 24 AWG solid bare copper conductors with HDPE insulation,

FR PVC or LSZH jacket, and an integrated ripcord beneath the jacket to

facilitate easy stripping and termination. The cable shall include a central

filler/slot for pair separation, ensuring compliance with performance

categories up to TIA‑568‑C.2/ISO 11801 Class E standards with full support

for Gigabit Ethernet. The overall assembly must be flexible enough for

structured LAN deployments and rated for indoor use.

8 Supply, install, test, and commission ceiling‑mount Wi‑Fi 6 Access Points, Nos 10 16,100.00 1,61,000.00

delivering ultra-high-speed dual-band connectivity (2.4 GHz + 5 GHz) using

IEEE 802.11ax. Each unit must support AX1800 to AX3000 performance,

offering minimum speeds of 574 Mbps on 2.4 GHz and 1201–2402 Mbps on

5 GHz, with MU‑MIMO, OFDMA, band steering, seamless roaming, and PoE+

support (802.3at). The design should be ultra-slim, unobtrusive, and suitable

for indoor ceiling placement, ideally provided with mounting kits and

centralized management (cloud or controller-based).

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

9 Providing and fixing raised access flooring system using steel encapsulated Sqm 10 5,597.00 55,970.00

cementitious core panels finished with 1.0 mm thick high-pressure antistatic

laminate (HPL), conforming to EN 438 standards. The system shall be of

Edge Support Rigid Grid (ESRG) type, capable of withstanding a

concentrated load of 360 kg (800 lbf), a uniformly distributed load (UDL) of

1650 kg/m², and pedestal axial load capacity of 22 kN. Pedestals shall be

made of heavy-duty galvanized steel, adjustable to ensure precise leveling

and securely fixed to the sub-floor. The stringers shall be of minimum 1.6 mm

thick galvanized steel, bolted rigidly to the pedestals and fitted with anti-

vibration PVC gaskets to provide structural stability. The entire system shall

be installed to achieve a finished floor height (FFH) of up to 400 mm. The

scope includes supply, installation, alignment, levelling, electrical earthing and

bonding of flooring panels, along with complete testing to meet the specified

load performance as per EN 12825. The panels must be fire-retardant,

abrasion-resistant, and electrostatically dissipative (ESD compliant with

resistance between 10⁶–10⁹ ohms).

All manufacturers shall have prior experience in supplying similar flooring

systems conforming to EN 12825 standards, with tested performance under

concentrated load, uniformly distributed load (UDL), pedestal axial load, and

fire-retardancy. Only OEMs having a proven track record of large-scale

installations in data centers, corporate facilities, government buildings, or

public sector undertakings (PSUs) shall be considered.

TOTAL OF DATA NETWORKING CARRIED OVER TO SUMMARY 32,08,470.00

XIV BOOM BARRIER

1 supply, install, test, and commission a hydraulic microprocessor-controlled Nos. 4 1,63,300.00 6,53,200.00

boom barrier system featuring a hydraulic pump unit, plunger pistons

counterbalanced by compression springs, and adjustable internal stops

for precise beam open/close positioning. Designed for 100% duty-cycle

continuous operation, the system shall reliably handle vehicle spans up to

3.5 meters, with robust auto-positioning and programmable

acceleration/deceleration profiles

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

The barrier shall include a precision boom arm, integrated controller unit,

hydraulic power assembly, limit switches, safety loop/photocell integration,

and all necessary accessories (remote control module/RS‑485 interface,

manual release, weatherproof housing). The system must offer rapid

opening/closing cycles (~1.3 seconds), adjustable speeds, and anti-crushing

safety mechanisms

2 Supply, install, test, and commission a twin‑channel exit push-button Nos. 4 1,150.00 4,600.00

station featuring both green (NO) and red (NC) push-buttons for door

open/close control as per access system requirements. Each button assembly

must be momentary action, double‑pole (DPDT) or dual contact (NO + NC),

constructed from brushed stainless‑steel front plate, and mechanically

rated for at least 1 million actuations. Mounting should support flush or

surface installation in single- or double-gang backboxes, with a minimum

current rating of 3–5 A at 12–24 VDC.

3 Supply, install, test, and commission a photocell safety sensor pair sets 4 4,600.00 18,400.00

(transmitter and receiver) designed for integration with vehicular boom

barriers to prevent inadvertent closing upon vehicle presence detection. The

system must feature infrared, single-beam operation, accurately interrupting

beam paths within a 5–10 m detection range, operating reliably in ambient

conditions from –20 °C to +50 °C, and powered via 12–24 VDC/AC. The units

should include anti-EMI filtering, LED alignment indicators, IP‑rated

enclosures (min. IP54), and solid NO/NC dry contacts to interface with

barrier control logic.

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

4 Supply, lay, test, and commission 3-core, 1.5 sq mm copper conductor PVC- mtr 150 300.00 45,000.00

insulated unarmoured cable, compatible with 300/500 V rating and

conforming to IS 694 (Part 1) or equivalent standards, installed through

existing conduits. The cable must feature solid or flexible electrolytic copper

conductors, PVC insulation and sheath (FR/PVC), and be suitable for fixed

installations. All installation shall include end termination, proper support,

testing for continuity and insulation resistance, and labeling per standard

electrical guidelines.

5 Supply and deliver a comprehensive set of connectors, interfaces, sets 4 5,750.00 23,000.00

mounting brackets, cords, modular jacks, plugs, cable tags/identifiers,

fixtures (clips/clamps), screws, nuts & bolts, all as required for completing

the cabling, mounting, and connectivity needs of the secure access and

networking system. These components must include high-quality Cat‑6 RJ45

pass-through connectors, panel‑mount and inline couplers, booted connector

boots, cable identifier tags, precision keystone jacks, nylon zip ties,

rapid‑mount clamps, brass/stainless hardware, and standardized screws and

bolts for rack or device installation

TOTAL OF BOOM BARRIER CARRIED OVER TO SUMMARY 7,44,200.00

XII LIGHTENING ARRESTOR- CAT LIGHTNING TERMINAL

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

1 supply, install, test, and commission a Controlled Advanced Triggering

(CAT) lightning protection system that includes a spheroid-configured air

terminal comprised of a blunt central finial surrounded by four electrically

isolated anodized-aluminium panels, mounted atop a 2 m tall × 4 mm thick

FRP mast. The system shall be fully compliant with IEC 60‑1:1989 and tested

to withstand impulse voltages of 500 kV and impulse currents of 180 kA,

employing UV‑resistant polymer insulation between panels with dielectric

strength exceeding 24 kV. The CAT terminal shall operate via spark-gap

corona-based triggering, without electronics, batteries, or moving parts, to

deliver efficient controlled streamer emission (CSE) at the optimal time to

intercept descending lightning leaders

Installation shall include mounting the CAT terminal on a non-conductive

FRP mast (min. 2 m length, approx. 60 mm diameter, ~4 mm wall thickness),

with a centre-fed insulated down conductor passing through the mast to

minimize side-flashing. An aluminium mast of min. 3 m height, mechanically

secured to the FRP section using U-bolts, must be provided to support

additional lightning rod height and structural stability

The full system shall also include high-voltage shielded down-conductor

(HVSC) cable per LPI standard, earthing pits with copper strips, ground

resistance-lowering compounds, and lightning strike recorder, all

designed to guarantee a low-impedance, safe discharge path as part of a

validated Guardian System 5 package

Recommended OEMs: LPI Lightning Protection International (Guardian

CAT® System 5) and nVent ERICO System 3000

Complete sets described as above Sets 1 1,75,000.00 1,75,000.00

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

Supply, install, test, and commission the threaded base adapter required to Sets 1 4,000.00 4,000.00

firmly bond the Controlled Advanced Triggering (CAT) or Early Streamer

Emission (ESE) lightning air terminal to the supporting mast and shielded

down‑conductor. This adapter—known as the LPI StorMaster‑ESE Mast

Base Assembly (GI or Butt adaptor)—features a female 2 inch BSP

threaded body for secure coupling with FRP or metallic masts, and is

equipped with a lug terminal to terminate the high-voltage shielded down-

conductor (HVSC Plus). Manufactured by Lightning Protection International

(LPI), the adaptor is made from galvanized iron (GI), ensuring precise

mechanical coupling and dependable electrical continuity within the LPI

Guardian CAT® or Stormaster ESE terminal systems

3 HVSC PLUS Down Conductor

SITC of designed LPI High Voltage Shielded Cable (HVSC Plus), a 7-layer RM 60 9,800.00 5,88,000.00

concentric down-conductor with ≥ 50 mm² aluminium core, 5 mm XLPE

insulation, copper tape screen, and UV-resistant PVC jacket. With an overall

diameter of approx. 36 mm and inductance of 93 nH/m, this low-impedance

cable is certified to withstand 500 kV impulse (1.2/50 µs) in accordance with

AS1931 Part 1 standards, offering reliable side-flash minimization in lightning

protection systems. It must be factory-fitted with an upper termination

assembly for connection to the lightning air terminal, and a lower termination

kit to bond safely to the earth pit.

This cable is integral to top-tier LPI Guardian CAT® System 5 installations,

ensuring controlled streamer emission and structured down-conductor routing

from terminal to grounding system. Per LPI’s technical datasheet, HVSC Plus

is manufactured via a triple-extrusion process and independently lab-tested to

meet IEC compliance certification

4 Terminations of Down Conductor

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

Supply, install, test, and commission both the Upper Termination Kit Sets 1 6,700.00 6,700.00

(UTERMKIT‑MK3) and Lower Termination Kit (LTERMKIT‑MK3) required

for connecting the LPI HVSC Plus high-voltage shielded down-conductor

to the Dynasphere/CAT/ESE air terminal and the dedicated lightning

protection earth pit, respectively. The upper kit, compliant with IEC 60060‑1

(1989), includes all accessories—semi‑conductive tape, insulating friction-

tool, crimp lug, heat-shrink tube—for completing a high-voltage termination

between the conductor and air terminal with controlled streamer functionality

The lower termination kit similarly includes a 95 mm crimp lug, waterproof

tape, earth-rod clamp, conductive paste, and warning labels to ensure safe

bonding to earth pit conductors

These termination kits are part of the globally recognized LPI Guardian

CAT® or Stormaster ESE system, manufactured by Lightning Protection

International (LPI)

Supply, install, test, and commission a 3‑metre galvanized iron (GI) mast Sets 1 28,750.00 28,750.00

designed for secure mounting of lightning protection systems. The mast shall

be fabricated from heavy-duty GI pipe, complete with a base plate, U‑bolt

mounting clamps, and guy-wire kit for robust anchoring to walls or rooftop

structures as required. The mast assembly must ensure stability and

structural integrity under wind loads, while enabling correct positioning and

bonding of lightning air terminals and down-conductor entry points

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

6 Supply, install, test, and commission a 2‑metre long, 50 mm diameter Sets 1 35,000.00 35,000.00

Fibreglass Reinforced Plastic (FRP) mast, specifically the LPI® FRP‑2M

insulated mounting pole. Engineered by Lightning Protection International

(LPI) of Australia, this mast provides essential electrical insulation and

weather resistance at the crucial junction between the CAT-type lightning

air terminal and the HVSC Plus down-conductor, enabling safe high-

voltage termination in compliance with LPI’s Guardian CAT® System

OEM: Lightning Protection International (LPI)

7 supply, install, test, and commission the LPI® Inline Coupling Unit—a Sets 1 31,000.00 31,000.00

precision-engineered cast-aluminium coupling designed to connect the

insulated FRP mast to an aluminium or GI lower mast, providing structural

rigidity and electrical bonding within the CAT/ESE lightning protection

assembly. The coupling features three integrated guy-wire anchoring points

for secure anchoring and includes a dedicated exit port for routing the

HVSC Plus down-conductor safely through the mast structure

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

8 Supply, install, test, and commission the LPI® Upper Termination Kit Sets 1 3,500.00 3,500.00

(UTERMKIT‑MK3), which is specifically designed to terminate the HVSC Plus

high‑voltage shielded down‑conductor to the Dynasphere/ Stormaster air

terminal in a CAT/ESE lightning protection system. This kit is fully compliant

with IEC 60060‑1 (1989) test standards and includes all necessary

components—semi-conductive tape, insulating friction cutters, heat-shrink

tube, crimp lug, and insulation tapes—to achieve a precision-engineered,

electrically safe termination. Manufactured by Lightning Protection

International (LPI Australia), the kit is certified as part of the Guardian CAT®

System 5 architecture and ensures dependable corona-based triggering and

high-voltage integrity as outlined in the official technical documentation

9 Supply, install, test, and commission the LPI Lower Termination Kit Sets 1 6,650.00 6,650.00

(LTERMKIT‑MK3), which facilitates the secure, professional termination of

the HVSC Plus shielded down-conductor into the dedicated earth pit

system of a CAT/ESE-type lightning protection installation. Offered by

Lightning Protection International (LPI, Australia), this kit includes all

required bonding hardware—such as heavy-duty crimp lugs, conductive

paste, sealing tapes, clamps, and warning labels—to ensure a low-

impedance, weatherproof and mechanically robust earthing connection

compliant with LPI Guardian CAT®/Stormaster ESE design standards

10 Lightning Protection System Earth:

Supply, install, test, and commission one complete chemical gel earthing Sets 3 20,700.00 62,100.00

system, featuring a 3 m × 17.2 mm copper‑bonded steel electrode (Model

JK‑317CBR), copper‑plated to 250 µm thickness, manufactured by JK

Chemrode (APS India). The rod is UL-listed, CPRI-tested for 46 kA

impulse current, ISO 9001/14001 certified, and ensures long-term stability in

corrosive soil conditions

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

This electrode shall be embedded in an earthing pit backfilled with 50 kg of

JK Reslow grounding minerals (two 25 kg bags), a BIS/NABL/BIS/MOEF-

certified hygroscopic compound that maintains interface earth resistance at

≤ 0.12 Ω·m even in dry conditions as per IEEE‑80‑2000 Clause 14.5 d

Installation includes forming the earth pit, positioning the rod centrally,

applying backfill compound, moisture conditioning, and completing earth-

resistance testing using the 4‑pole method to ensure ≤ 1 Ω resistance,

followed by proper pit sealing, labeling, and certification documentation.

Lightning Event Counter:

11 Supply, install, test, and commission a mechanical, non-resettable Sets 3 17,500.00 52,500.00

Lightning Strike Recorder (e.g., LPI model LSR‑I/LSR‑2) in a robust IP 67

polycarbonate housing, designed to record lightning impulse currents on the

down‑conductor without battery or external power. The unit shall activate on

impulse currents ≥ 1,500 A (8/20 µs waveform), record up to 220 kA, and use

a purely electromechanical 6‑ or 7‑digit register that cannot be reset—LCD

displays are not permitted. The recorder must be tested to

IEC 60060‑1:1989 standards, certified in association with ESE/CAT arresters

to handle impulses over 450 kA reliably. The device shall operate from −15 °C

to +65 °C, with dimensions approximately 80×82×65 mm, weighing about

0.4–0.6 kg, and mount directly onto the down‑conductor via ultraviolet-

resistant stainless cable ties (for up to 40 mm diameter cable or 50×5 mm flat

tape) as per OEM design

POLYPLASTIC EARTH PIT CHAMBER WITH COVER

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

12 Supply, install, test, and commission a heavy-duty polyplastic earth pit Sets 3 1,100.00 3,300.00

chamber, fabricated from UV‑stabilised polyethylene, measuring 254 mm

top diameter, 330 mm bottom diameter, and 260 mm height, with an

auto‑locking polyethylene cover. The chamber shall feature four factory-

punched knock‑out openings on its sides to enable seamless

interconnection of earth strips between pits in a grounding grid. Constructed

to be corrosion-resistant, load-bearing (minimum 3 ton static capacity), and

environmentally friendly, the unit allows easy inspection and maintenance.

The locking lid shall be jam-free and weather sealed to block pests and debris

13 supply, install, test, and commission a Test Joint Point (TJP) comprising Sets 1 2,000.00 2,000.00

a 25 mm × 6 mm × 300 mm pure copper flat strip, securely mounted inside

a weatherproof ABS enclosure to allow onsite measurement and inspection

of grounding continuity. The copper strip shall be manufactured from ≥99.9 %

pure electrolytic copper, thickness 6 mm and width 25 mm, commonly used

in earthing bonding grids for exothermic weld connections and testing loops.

The ABS box shall be IP‑65 rated, UV-stabilized, with lockable hinged lid,

mounting flanges, and space for cable entry and sacrificial test terminals

1. Contractor shall be responsible for obtaining earth-pit resistance results as

2. Depth of earth pits to be decided accordingly to achieve desired results.

3. Contractor shall be responsible for the adequacy of the design of the

lightning protection system. The number of ligntning conductors and earth pits

to be decided as per requirement. The quantities given below need to

confirmed by the contractor for system suitability or else to be increased as

TOTAL OF LIGHTENING ARRESTOR CARRIED OVER TO SUMMARY 9,98,500.00

S.H.-IX SOLAR SYSTEM

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

1.0 SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM 30 kWp

grid‑connected rooftop solar PV system

1.1 Design, Engineering, Procurement, Supply, Installation, Testing, System 1 17,50,000.00 17,50,000.00

Commissioning of a 30 kWp grid‑connected rooftop solar PV system and

Net‑Metering management for a 30 kWp grid‑connected rooftop solar PV

system to be installed on the terrace of the premises. The system shall

comprise high-efficiency Mono PERC PV modules (540 Wp or higher) and

string-type inverters with MPPT, mounted on hot-dip galvanized structural

steel elevated structures suitable for RCC rooftops. The structural design

must comply with IS 875 norms addressing wind, seismic, and live loads,

while preserving rooftop waterproofing and drainage.

The system must meet a Performance Ratio (PR) of at least 75 percent,

and maintain a Capacity Utilization Factor (CUF) of ≥ 15 percent

annually—adjusted to local Global Horizontal Irradiance (GHI)—for a

minimum period of five years, consistent with MEDA guidelines and MERC

policy. These thresholds shall demonstrate at initial inspection to qualify for

incentive disbursement and must be sustained.

The Contractor shall manage the entire net-metering process under the

MERC Net Metering for Rooftop Solar Systems Regulations, 2015

(including amendments up to 2017), coordinating with the local DISCOM for

application submission, feasibility studies, interconnection agreement

execution, installation of bi-directional net meter, inspection and sealing, all

documentation, and grid synchronization at the net-meter boundary. The

DISCOM’s transformer-level connection limit of 40 percent of DT capacity

must be observed; any exceedance requires DISCOM feasibility approval.

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

The Contractor shall conduct all pre-commissioning tests including insulation

resistance, continuity, polarity, voltage/current accuracy, and PR/CUF

validation and submit a comprehensive commissioning report containing test

results, single-line diagrams, O&M manuals, warranties, and Commercial

Operation Date documents. Post-synchronization, the Contractor shall assist

the client in claiming net-metering credits and government subsidies.

Performance warranties shall guarantee module output degradation of no

more than 10 percent at 10 years and 20 percent at 25 years, and inverter

warranty for a minimum of 5 years. Maintenance services—including

cleaning, inspection, and fault resolution—must be provided for at least 1

years, with response time for corrective action within 48 hours.

The price quoted by the Contractor shall be firm and inclusive of all duties,

taxes, insurance (transit, storage, erection), net-metering fees, DISCOM

interface costs, and O&M obligations. Compliance with MERC net-metering

regulations, CEA connectivity standards, MNRE rooftop PV guidelines,

and applicable DISCOM specifications (e.g. MSEDCL, Tata Power, BEST) is

The Contractor shall deliver a fully water‑tight turnkey rooftop solar PV

installation on the terrace of the premises, covering all structural steel

fabrication and mounting works, civil and plumbing works, electrical

installation, and post‑installation cleaning arrangements. Structural steel

supports, fabricated from hot‑dip galvanized, must be designed, engineered,

and installed to suit RCC terraces, complying with IS 875 for wind, seismic,

and load factors, and incorporating slip‑sheet or rubber pad protection to

prevent concentrated surface loads and roof membrane damage.

All mechanical penetrations including anchor bolts, cable entries, and junction

box mounts—must be sealed with appropriate flashing systems, Dektite-

style collars, UV‑resistant sealants, and EPDM gaskets, ensuring

long‑term watertight integrity and resistance to uplift and thermal cycling .

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

Cabling must be meticulously routed in weatherproof conduits and glands,

with all exposed entries sealed and drainage points provided to avoid water

pooling or conduit entry flooding; spare gland holes must be plugged, and

exterior seals maintained using products rated for UV exposure and Indian

monsoon conditions . Electrical components—including isolators, junction

boxes, SPDs, and inverters must be installed in compliance with IP rating

requirements and manufacturer specifications, with their housings protected

from water ingress and placement optimized to minimize exposure to direct

sunlight and moisture

The Contractor shall execute a final cleaning protocol, including removal of

installation debris, thorough flushing of mounting footings and neighborhoods,

removal of rust or foreign particles, and washing of PV module surfaces to

ensure full performance from day one. A comprehensive waterproofing

inspection and rain test must be performed post-installation; any leak or

potential ingress point discovered must be permanently sealed before

commissioning .

Together, these provisions should guarantee that the entire rooftop PV

system—including structural steel, civil and plumbing modifications, electrical

infrastructure, and finishes—remains fully watertight and leak-proof

throughout its lifespan, preserving the terrace’s waterproof membrane

integrity while ensuring maximum performance and longevity.

The Contractor shall be responsible for designing and implementing safe and

practical access solutions to facilitate module cleaning and routine

maintenance throughout the O&M period. The mounting structure shall

incorporate adequate walkways, crawl space, or service gaps (typically

≥ 800 mm horizontally and ≥ 600 mm vertically between rows or arrays) to

allow cleaning personnel to move safely without stepping on or damaging the

PV modules, as per established rooftop PV installation guidelines

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

All access routes and platforms shall be integrated with fall-protection

measures such as anchor points, temporary guardrails, lifelines, or safety

nets compliant with working-at-height standards. The design layout must

ensure safe maneuvering and cleaning access, this spacing shall also assist

in minimizing manual damage and enable airflow for module cooling and

rainwater drainage

the Contractor shall supply & install means of safe roof entry, including

ladders, scaffolding, or anchor-based harness systems, in accordance with

best practices for rooftop solar cleaning safety . Personnel performing

cleaning must be trained and provided with appropriate PPE, including non-

slip footwear, insulated gloves, harnesses, and tools such as soft brushes,

squeegees, and deionized water systems, to avoid panel damage and

electrical hazards

the quoted costs shall Includes cost of all structure steel, panels, inverter,

cables, SPD, LA, earthing, signage, remote monitoring, net meter, and all civil

The Contractor shall coordinate with the concerned State Electricity

Distribution Company (DISCOM) for the application, processing, and approval

of net metering, including the supply and installation of a bi-directional net

meter (single-phase or three-phase as applicable) for grid-interactive solar

photovoltaic systems.

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

S. No. DESCRIPTION OF ITEM UNIT TOTAL RATE TOTAL AMOUNT

The scope shall include:

-Liaison with DISCOM for net metering approval and application processing.

-Payment of necessary application and registration fees to DISCOM.

-Supply of bi-directional energy meter (as per DISCOM specifications,

typically LT or Secure make, accuracy Class 0.5/1.0, suitable for import/export

energy metering).

-Installation, testing and commissioning of net meter in the existing LT/HT

panel board with necessary wiring, interconnection, and protection

arrangement as per IE Rules and DISCOM standards.

-Submission of all technical documents, test certificates, and drawings as

required for approval.

-All statutory charges, coordination fees, and government levies shall be

included in the quoted rate.

-All associated civil, electrical, plumbing works, like meter box, sealing

arrangement, or support structure shall be deemed included.

TOTAL OF SOLAR SYSTEM CARRIED OVER TO SUMMARY 17,50,000.00

NBCC (INDIA) LIMITED ELECTRICAL WORKS NDSR Digitally signed by VARUN

WRPC-ANDHERI-MUMBAI

SCHEDULE OF QUANTITIES

EXTERNAL DEVELOPMENT WORK

S. No. Description of item DSR Amount NSR Amount DSR+NSR Amount

1 EXTERNAL WATER SUPPLY & GARDEN HYDRANT SYSTEM 14,42,109.00 4,76,410.00 19,18,519.00

2 EXTERNAL SEWERAGE, DRAINAGE AND RAIN WATER HARVESTING 41,63,107.00 4,80,900.00 46,44,007.00

Digitally signed by VARUN

WRPC-ANDHERI-MUMBAI

BILL OF QUANTITIES

EXTERNAL WATER SUPPLY & GARDEN HYDRANT SYSTEM

S. No. DSR-2023/ Description of item Unit Rate Amount Rate Amount

Providing and laying cPVC pipes of the following dia conforming to

IS:1239 and ISI marked (medium grade) in trenches complete with

cPVC fittings & flanges including excavating in trenches in any type

of soil, including back filling, spreading of surplus earth in layers not

exceeding 20 cm in depth including consolidating each deposited

layer by ramming, watering within the site as per direction of

PD/Architect and anti corrosive treatment (painting pipes with two

coats of Bitumastic paint, wrapping polythene tape and applying a

final coat of bitumastic paint) covering pipes 10 cm all around with

sand of grading zone V or coarser grade, testing and dis-infection

with water containing bleaching powder complete all as specified

and as directed by Project Director/Architect.

Providing and fixing CPVC ball valve of approved quality and make,

conforming to IS 15778 / ASTM D2846 standards, suitable for SDR

11 piping system. The valve shall be made from CPVC (Chlorinated

Polyvinyl Chloride) material with high chemical resistance, having

full bore design for minimum pressure drop, and equipped with a

reinforced handle for easy operation. The valve shall be pressure-

rated for PN16 or equivalent, suitable for both hot and cold water

systems up to 82°C. The ball and stem shall be of CPVC or brass

(as specified), with PTFE or EPDM seals for leak-proof operation.

Valve ends shall be solvent-welded socket type, compatible with

CPVC pipes and fittings of respective sizes. The installation shall

include all necessary fittings, supports, and accessories, tested for

leak-free performance and completed as per manufacturer’s

specifications and direction of Engineer-in-Charge

Digitally signed by VARUN

NBCC (INDIA) LIMITED EX WATER GARDEN HYDRANT SINGH

S. No. DSR-2023/ Description of item Unit Rate Amount Rate Amount

Providing and fixing C.I. double acting air valve of approved quality

3 18.59 with bolts, nuts, rubber insertions etc and testing complete including - -

the cost of tail pieces all as specified for following sizes.

Providing and fixing C.I. sluice valve conforming to IS: 14846-2000

of PN 1.6 class 1 and I.S.I. marked with cap complete including

4 18.31 fixing with rubber packing 3 mm thick, nuts and bolts etc. and testing - -

complete including the cost of tail pieces all as specified for following

Providing and laying 1:2:4 cement concrete (1 cement: 2 coarse

sand: 4 graded stone aggregate 20mm nominal size) for thrust block

including necessary excavation, centering, shuttering and plastering

Material and labour for construction of masonry chamber 60x60x75

cm inside with bricks of class designation 7.5 in cement mortar 1:4

(1 cement : 4 coarse sand) for sluice valve with C.I. surface box

100mm dia at top,160 mm dia at bottom and 180 mm deep (inside)

with hinged cover fixed in R.C.C. slab 1:2:4 mix ( 1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size)

6 18.36.1 necessary excavation in any type of soil, foundation concrete 1:5:10 Nos 18.00 - 10,354.95 1,86,389.10

( 1 cement : 5 coarse sand: 10 graded stone aggregate 40 mm

nominal size) and inside plastering with cement mortar 1:3 ( 1

cement : 3 coarse sand ) 12 mm thick finished with a floating coat of

neat cement complete as per standard design including disposal of

excavated earth within the plot as per direction of PD/Architect and

all as specified and shown on drawings.

Digitally signed by VARUN

NBCC (INDIA) LIMITED EX WATER GARDEN HYDRANT SINGH

S. No. DSR-2023/ Description of item Unit Rate Amount Rate Amount

Material and labour for construction of masonry chamber 30x30x50

cm inside with bricks of class designation 7.5 in cement mortar 1:4 (

1 cement : 4 coarse sand) for stop cock with C.I. surface box

100x100x75 mm (inside) with locking arrangements and RCC top

slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate

20 mm nominal size ) necessary excavation in any type of soil,

foundation concrete 1:5:10 ( 1 cement : 5 coarse sand : 10 graded

stone aggregate 40 mm nominal size ) and inside plastering with

cement mortar 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished

with a floating coat of neat cement complete as per standard design

including disposal of excavated earth within AWHO plot as per

direction of PD/Architect.

Structural steel work welded in built up sections, trusses and framed

work including cutting, hoisting, fixing in position and applying a

priming coat of approved steel primer and two or more coats of

enamel paint all complete.

Providing and fixing of garden hydrant outlet comprising 20 mm dia

heavy-duty brass ball valve and brass bib cock suitable for garden

hose connection, complete with necessary G.I./CPVC piping, fittings,

and connections as shown on drawings. The hydrant outlet shall be

housed within a brick masonry chamber of internal size

approximately 300 mm x 300 mm x 450 mm (depth), constructed

using first-class bricks in cement mortar 1:4, plastered inside with 12

9 MR mm thick cement plaster, and finished externally with cement Nos 16.00 6,000.00 96,000.00

pointing. The top of the chamber shall be covered with a precast

RCC or cast iron hinged cover for easy access. The outlet shall be

suitable for manual irrigation/gardening operations and capable of

withstanding pressure up to 10 kg/cm². The entire assembly shall be

installed as per manufacturer’s recommendations and project

specifications, complete in all respects as directed by the Engineer-

Approved Makes / OEMs (Brass Valves and Bib Cock):

Heavy-duty ISI marked generic brands (for non-potable outdoor use)

Providing & fixing BUTTERFLY VALVE (MANUAL) with C I body SS

10 Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled - -

water/hot water circulation as specified.

Digitally signed by VARUN

NBCC (INDIA) LIMITED EX WATER GARDEN HYDRANT SINGH

S. No. DSR-2023/ Description of item Unit Rate Amount Rate Amount

Providing & fixing NON - RETURN VALVE with duel plate of C I

ELECT. DSR body SS plates vulcanized NBR seal flanged end & PN 16 pressure

2022 / 16.7.3 rating for chilled / hot water circulation including insulation as

Providing and fixing in position 25 mm diameter mosquito proof

coupling of approved municipal design.

Providing all materials and labour for making connection of new

water supply line with the existing municipal water supply line,

including careful excavation, exposing existing pipeline, cutting and

tapping as required, installation of necessary fittings such as saddle

clamps, tees, valves, reducers, and pipe sections for proper

integration. The work shall include breaking and cutting of

road/footpath/paved surfaces using appropriate tools, laying of pipes

and fittings, refilling with selected earth or sand in layers with proper