SPECIAL REPAIR TO AAGOSH OMQS AND MOORING POINTS ON TARMAC AT HQ SWAC COMN FLT UNDER GE (AF) CHILODA

Amount

Taking down cement plaster on brick or PCC block masonry wall in any description complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the rubbies complete all as specified and directed.

Taking down existing chowkats or frames n.exc. 1.5 Sqm each removing to from store or handed over to contractor complete all as specified and directed.

Taking down existing chowkats or frames exc. 1.5 Sqm but n exc 4.0 Sqm each removing to from store or handed over to contractor complete all as specified and directed.

S&F in repair Prelaminated particle board 25mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including brass door handle and brass knob complete all as specified and directed.

S&F butt hinges 100mm medium weight colled rolled miled steel complete all as specified and directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, bright finished complete all as specified and directed.

S&F 150mm size brass handles, cast type anodised complete all as specified and directed.

Taking up or down old/chocked water tubings 15mm bore with fittings from trenches /walls and stacking at site all as directed by Engineer-in-Charge.

Taking up or down old/chocked water tubings 20 mm bore with fittings from trenches /walls and stacking at site all as directed by Engineer-in-Charge.

Taking up or down old/chocked water tubings 32 mm bore with fittings from trenches /walls and stacking at site all as directed by Engineer-in-Charge.

Demolition Cement concrete (unreinforced) Concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L 50mm average thickness PCC 1:2:4 type B0 using 12.5mm graded aggregate as in padding and (roof levelling course) on roof surfaces complete all as specified. Note- Water proofing compound to be used @ 3% by weight of cement content for concrete padding work complete all as specified and directed.

M&L for rendering in CM (1:3) 10mm thick over RCC roof, chajja/ brick wall mixed with water proofing compound @ 3% by weight of cement finished even and fair without using extra cement. Note - WPC shall be measured and paid separately complete all as specified and directed.

M & L in repairs for roof treatment with following specification completely, complete all as specified and as directed by Engineer-in-Charge :- (i) Applying a coat of hot bitumen 85x25 @ 1.2kg per sqm. (ii) Laying 3mm thickness APP modified membrane weighting not less than 3 to 4 kg/sqm in 100 mm over laps both longitudinally and transversally and overlaps to be sealed by torch, membrane shall be taken upto the thickness of slab/front fascia.

S&F in repair rotational moulded water storage tank 1000 Ltr capacity double layer (cylindrical/vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Supply & Fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi?chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply only 5.5 mm thick sheet oridinary quality glass and glazing with rubber packing around the glass, in squares n exceeding 0.50 sqm in each pane complete all as specified and directed.

Supply only 5 mm thick sheet figured glass and glazing with rubber packing around the glass, in squares n exceeding 0.50 sqm in each pane complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick/concrete surface in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering to ceiling in 5mm thick on fair faces concrete surface in CM (1:3) finished even and smooth without using extra cement complete all as specified and directed.

M&L for external rendering 5mm thick in CM 1:4 with water proofing compound (water proofing compound shall be used as per manufacturers instructions) over a coat of 10mm thick in CM 1:6 over brick or concrete surfaces finished even and fair complete all as specified and directed.

Supply only water proofing compound conforming to IS-2645,1975 complete all as specified and directed.

M&L for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of new plastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

All as per Item No 27 above here in before on ceiling complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. Note : All work to be operated by mechanically (i.e Grinder Machine and Air less painting machine) not by blade / brush / roller / normal spray machine)

M & L for Virified Ceramic tiles Tiles 10mm thick, Coloured, polished, of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 mm to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

All as per item No 30 here in before, but on vertical surfaces incl 10mm thick CM 1:3 as in baking coat of dado/skirting complete all as specified and directed.

M & L for Non Skid Ceramic Tiles, Coloured, of size exceeding 0.11 Sqm and not exceeding 0.18 Sqm, 7 mm to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L Coloured Glazed ceramic tiles in vertical surfaces350X250X7mm/ 450X350X 7mm thick as in skirting /dado, set and jointed in cement slurry and pointed in coloured cement to match laid over 10mm thick cement backing coat in CM 1:3 complete all as specified and directed.

M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for 75mm thick Cement concrete Type D2 1:4:8 (40 mm graded graded aggregate) as in floor finishes and pavings as sub base complete all as specified and directed.

M&L for 75mm thick Cement concrete Type D2 1:2:4 (40 mm graded graded aggregate) as in floor finishes and pavings as base complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 15mm thick cement backing coat in CM 1:4 complete all as specified and directed .

M & L for 300 x 300 x 10mm thick coloured heavy duty vitrified exterier chequered tiles as in floor/wall set and jointed in cement slurry and pointed in coloured cement to match laid over 15mm thick cement mortar in CM 1:6 complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and directed.

S & F 100 mm size, Butt hinges, Stainless Steel, Medium weight, bright polished including fixtures complete all as specified and directed.

S & F 150 mm long Aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and directed.

M&L complete removal existing wall surface applying two coats of oil bound distemper over a coat of alkali resistant priming paint including preparation of new plastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

All as per Item No: 44 above here in before on ceiling complete all as specified and directed.

M&L for applying one coat of acrylic emulsion weather coat premium quality antifungal exterior emulsion to old painted surface of wall including preparation complete all as specified and directed. Note : All work to be operated by mechanically (i.e Grinder Machine and Air less painting machine) not by blade / brush / roller / normal spray machine)

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S & F MS steel work in tubular /post/trusses/purlin including special shaped washers base and bed plate cleat nut and bolt etc confirming to IS 1161- 1979 graded St 240 complete all as specified and directed.

S&F Stairs (framed) including stringers, treades, landing balusters, hand rails etc. including cleats brackets Fe 290 (Gde E-165) etc complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

M&L for Plates (Plain or Chequered) channels, square or notched (Ordinary and counter sunk) forming holes, without any attachment of Fe 290 (Gde E-165) complete all as specified and directed by Engineer in Charge.

S&F Expanded metal wire mesh weigth n exc 4 Kg per Sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and directed.

Supply & fixing in repair with semi perforated 12mm thick micro tegular edged GRG false tiles at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge.

S&F in repair curtain rod / harrison rails miold steel chromium plated with fixed brackets , stops, rollers etc, 25 mm dia with fixed brackets , stops rollers etc complete all as specified and directed.

Supply and fixing 15 mm outer dia CPVC pipes of pressure rating 10kgf/cm2 fixed complete to walls ,ceiling s or in floors etc complete all as specified and directed.

Supply and fixing 20 mm outer dia CPVC pipes of pressure rating 10kgf/cm2 fixed complete to walls ,ceiling s or in floors etc complete all as specified and directed.

Supplying and laying of CPVC pipes 32mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. In repair complete all as specified and directed.

Supplying and fixing of CPVC Brass Elbow 16 mm outer dia complete all as specified and directed.

Supplying and fixing of CPVC Brass Tee 16 mm outer dia complete all as specified and directed.

Supplying and fixing of CPVC Brass Tee 20mm outer dia complete all as specified and directed.

Supplying and fixing of CPVC Brass Elbow (3/4 X ½) 20mm outer dia complete all as specified and directed.

Supplying and fixing of CPVC Brass UNION 16 mm outer dia complete all as specified and directed.

Supplying and fixing of CPVC Brass UNION 20 mm outer dia complete all as specified and directed.

S & F in repairs Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repairs 15mm CP Bib Taps long body fancy type heavy duty with wall flange complete all as specified and directed.

S&F in repair brass chromium plated over head shower rose with arm 125 mm size with long body with swivel joint including fixing to steel pipe or union, complete all as specified and directed.

S & F in repairs Angular cock 15 mm dia, cast copper alloy with capstan head, screwed down high pressure with long shank and cup fancy type for iron pipe etc complete all as specified and directed.

S&F in repair Corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern) EWC white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan (semi pedestal pattern) Anglo Indian Type white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete all as specified and directed.

S&F plastic water closet seat cover, white or black colour closed pattern with flat bottom including taking down old seat cover complete all as specified and directed.

S&F in repairs 10 litres capacity PVC valveless symphonic action type, flushing cistern, low level, white, with inlet, ball valve float handle including brackets complete all as specified and directed.

S & F in repairs Vitreous china ware wash hand basin, white, flat back of size 550 mm X 400 mm including 32mm brass chromium plated waste fittings with long screw shanks and fly nuts, flange and waste pipe end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, etc complete all as specified and directed.

S&F in repair 20 mm brass chromium plateds towel rail of 20mm dia and 600mm in length 'D' shaped between flanges complete all as specified and directed.

S&F in repair for powder coated aluminum peg set of 4 solid body complete all as specified and directed.

S&F in repair Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws asspecified complete all as manufacturers instruction complete all as specified and directed.

S&F in repair Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing complete all as specified and directed.

S&F in repair 2mm thick fibre glass reinforced translucent corrugated/plain sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

S&F in repair Aluminium wind ties for roof including all necessary drilling, bolting or rivetting fixed with GI self tapping screws as specified for roof sheeting complete all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer on steel surfaces of any description, over 10 cm width or girth, not otherwise described including preparing new steel surfaces complete all as specified and directed.

M&L in repair precast cement concrete block masonry with PCC solid blocks in 1:3:6 type C1 using 20mm graded stone aggregates, exc. 10cm in width and set in CM 1:4 complete all as specified and directed.

M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection and finished even and smooth with using extra cement complete all as specified and directed.

S&F in repair 15mm Pillar taps fancy type , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair Stainless steel graing of 150mm dia with hole or without hole for wast pipe for trap complete all as specified and directed by Engineer in Charge

S&F in repair 100mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) 110 mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including claps and Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof on every Mtr complete all as specified and directed by Engineer in Charge.

S&F in repair 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F in repair 110 mm diaPVC (SWR) junction double,(double T), equal or unequal complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) vent cowl complete all as specified and directed.

Material and labour for applying one coats of synthetic enamel paint on steel surfaces of any description, over 10 cm width or girth, not otherwise described including preparing complete all as specified and directed.

Material and labour for applying one coats of synthetic enamel paint on wooden surfaces of any description, over 10 cm width or girth, not otherwise described including preparing complete all as specified and directed.

S&F in repair door closer hydraulically regulated designation No 3 universal type, aluminium (Die Cast) body suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Earth work in any kind of soil, excavation by mechanical means (Hydraulic excavator) / Manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in charge. (Removal of existing lights on link to be done by user/SRE Rep)

M & L for Laying and compacting 300 mm thick (compacted thickness) Granular Sub Base Course (GSB) in two layers of 150mm thick each (grading as per Grade I as specified Table 400-1 of MoRTH specifications for Road and Bridge works, 2013, in a single layer over compacted subgrade with natural sand, crushed gravel, crushed stone, crushed slag or combination thereof as per the grading required. The materials are mechanically mixed, spread and levelling on the subgrade by using motor grader of adequate capacity or manual, and rolling with vibratory of capacity 80-1 00 KN static weight /manual for achieving required compaction density of atleast 98% of the Maximum Dry Density. Consolidating to required gradient and camber complete all as specified and directed with finished surface tolerances as per Table 900-1 of MoRTH specifications for Road and Bridge works, 2013 complete all as specified and directed by Engineer in Charge.

M & L for Laying for 75 mm thick (compacted thickness ) WMM laid in three layers of 75 mm each. Wet Mix Macadam (WMM) grading as per table 400-13 of MoRTH specifications for Road and Bridge works 2013 manufactured in WMM plant material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading with paver / manual and rolling with vibratory static weight and consolidating to required gradient and camber complete all as specified and directed. The finished surface tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013 complete all as specified and directed by Engineer in Charge.

Providing and Laying Dry lean Concrete (DLC) 150 mm thick of aggregate gradation as per Table 1 of SP 49 :2014 having 7 day average compressive strength not less than 7 MPa Minimum cement content not less than 140 Kg/Cum DLC mixed in Batching Plant, transported to site and laid by electronic sensor paver or manually including spreading and compacting using high amplitude tamping bars of paver (initial compaction) / manual further by vibratory to achieve minimum dry density not less than 98% of max imum Dry Density, necessary finishing etc complete all as specified and tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge work 2013 complete all as specified and directed by Engineer in Charge.

M & L for 10 mm thick sand cushion with clean river sand duly clear of residual, organic and deleterious materials spread evenly to uniform thickness laid over DLC layer complete all as specified and directed. (No additionaI amount to be paid for overlap)

M & L for Supplying and laying 400 micron thick HDPE sheet (Virgin Quality) / Polythene sheet water proof, wrinkle free without puncture having minimum weight 390 gm/Sqm over tack coat sand cushion as specified in the design with overlap between adjacent strips and at transverse joints as minimum 300mm complete all as specified and directed.

M & L Pavement quality concrete(PQC) of minimum 28 days field Flexural strength of 45Kg/ Sqcm or 4 .5 Mpa, aggregate gradation as per Table 3 of IRC 15 2017, coarse aggregate of clean , hard strong, dense non-porous and durable pieces of crushed stone or gravel, fine aggregates of clean natural sand or crushed stone sand or combination of both using minimum 360 kg/cum of cement with non -circular virgin synthetic fibre of 12-18 mm length, specific gravity 1.34 to 1 .39, UV stable, alkali resistant, with equivalent dia 15-40 micron, minimum melting temperature as 240 °C and minimum tensile strength of 300 Mpa and at the rate as specified by the manufacturer. PQC laid, spread and compacted with slip-form paver of minimum 7.50 m width or manually, including curing and tining complete all as specified and directed. Requ ired surface texturing to be done as specified in IRC' 15-2017 complete all as specified and directed by Engineer in Charge. (Installation of taxiway lights, connection and positioning of lights etc to be done by user rep/SRE Rep during exicution of work)

M & L for Forming 20 mm width expansion joint in concrete slab for full depth of PQC. Early entry saw and subsequent cutting by using diamond bit cutter of appropriate size. straight and smooth edges. Join cleaned thoroughly with application of compressed air. Joint shall be made dry, vacuum cleaned and free of dirt, oil, vegetation and other debris. The joint then filled with pre-molded 20 mm thick compressible polyethylene closed cell type filler board as specified thereafter application of two coats of primer with thin brush by forward and backward movement at an interval of 30 minutes before placing the backup rod and pouring the sealant Placing of closed cell medium density, crossed linked polyethylene foam backup rod of 25 mm dia, over filler board and filled with polyurethane based sealant complying with BS 5212, BS 4254 and EN-141875-2003 with minimum movement accommodation factor (MAF) of+/- 30% having minimum 10 year performance guarantee applying masked tape on the edges of joints and removing the masking tape after filling of sealant as per the method specified by the manufacture complete all as specified and directed by Engineer in Charge.

M & L for Cutting of construction joints 25 mm deep and 10 mm wide by early entry saw cut using diamond bit cutter of appropriate size, straight and smooth edges. Joint cleaned thoroughly with application of compressed air. Joint shall be made dry, vacuum cleaned and free of dirt, oil, vegetation and other debris Application of two coats of primer with thin brush by forward and backward movement at an interval of 30 minutes before placing the backup rod and pouring the sealant. Placing of closed cell medium density, crossed linked polyethylene foam backup rod of 12 mm dia, application of bond breake tape on top of back up rod for complete width of the joint and filled with polyurethane based sealan complying with BS-5212, BS 4254 and EN- 141875-2003 with minimum movement accommodation factor (MAF) of +I- 30% having minimum 10 year performance guarantee, applying masked tape on the edges of joints and removing the masking tape after filling of sealant as per the method specified by the manufacturer complete all as specified and directed by Engineer in Charge.

M & L for preparing bituminous surfaces of road / PQC of runway / Tarmac area and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic / epoxy based for tarmac area road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed.

M&L for removing excavated earth /material exc 1.5km but n.exc 5.00 m depositing where directed at level n.exc 1.50Mtr above the starting point complete all as specified and directed.

S&F 25mm dia stainless steel ring or D shape with 20mm plate and Two Nos 25mm dia fastner minimum length 300mm including drilling and fixing on tarmac area, total weight of each ring, plate and fastner should not less then 3 Kg complete all as specified and directed by Engineer in Charge.

Taking down carefully copper/ aluminum point wiring (Light, fan, socket, power and Bell) including fixture and fittings such as switches, sockets, ceiling roses, lamp, holder , regulators, sockets light fittings etc , removing material to store for keeping in safe custody or for taking credit , and making good disturbed surface of walls, floors, etc. complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm single core PVC insulated unsheathed multi stranded copper conductor FRLSH cable 1100V grade drawn through and incl PVC concelled conduit with accessories like bends tees, junction boxes etc fixed recessed in wall or ceiling etc including 1.5 Sqmm single core PVC insulated but unsheathed multistrandard copper conductor FRLSH cable 1100V grade as earth continuity wire incl modular sunken type pressed steel terminal boxes of size with 3mm thick bakelite steel white/coloured top cover for the following :- (a) One light point controlled by one switch complete all as specified and directed.

All as per item No 110 here in before one fan point controlled by one switch complete all as specified and directed.

All as per item No 110 here in before one 3 pin socket out let 5 Amps on the independent board complete all as specified and directed.

All as per item No 110 here in before one 3 Pin socket out let 5 Amps on the same board complete all as specified and directed.

All as per item No 110 here in before with cable of size 2.5 Sq mm PVC insulated on independent board for power plug 15 Amps complete all as specified and directed.

Supply and fixing Modular switch one way 6A,1 Module, complete all as specified and directed.

Supply and fixing Modular switch one way 16A,1 Module, complete all as specified and directed.

Supply and fixing Modular socket 6/10A-2/3 pin combined 2 Module complete all as specified and directed.

Supply and fixing Modular socket 16/15A-2/3 pin combined 2 Module complete all as specified and directed.

Supply and fixing Modular Fan Regulator, 120W, 2 module complete all as specified and directed.

Supply & fix ceiling rose 3 terminal/ poly carbonate, isolated body complete all as specified and directed.

M&L for concealed sub main wiring complete with PVC insulated FRLSH cable of single core 4 Sqmm 1100 volts grade with multi standard copper conductor for drawn through and including conduiting PVC Conduit with accessories incl 4 Sqmm unsheathed multi standard FRLSH copper conductor as earth wire. Note: Two runs of cable and one run of conduit & earth wire shall be measured as one run length complete all as specified and directed.

M&L for concealed sub main wiring complete with PVC insulated FRLSH cable of 3 run of single core 10 Sqmm 1100 volts grade with multi standard copper conductor for drawn through and including conduiting PVC Conduit with accessories incl one run of 10 Sqmm unsheathed multi standard FRLSH copper conductor as earth wire. Note: four runs of cable and one run of conduit & earth wire shall be measured as one run length complete all as specified and directed.

Taking down old unserviceable DBs/MCCBs/MCBs complete all as directed by Engineer-in-Charge.

Supplying and fixing of sheet meal enclosure for VTPN DBs 4 way with addl space to fix the 100 Amps MCCB complete all as specified and directed.

Supplying and fixing of sheet metal enclosure, single phase, double door SPN DB 12 way, flush to wall mounting for MCB fitted with 200 Amp rated bus bars and neutral links ( without MCB's) SPN/ TPN complete all as directed by Engineer-in-Charge.

Supplying and fixing of sheet metal enclosure, single phase, double door SPN DB 8 way, flush to wall mounting for MCB fitted with 200 Amp rated bus bars and neutral links ( without MCB's) SPN/ TPN complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of MCCB 415 Volts, 16 KA, 4 pole of 100 Amps rated capacity complete all as specified and directed.

Supplying and fixing 415 Volts 10 KA 'C' Curve MCB TPN 4 pole of 63 Amp capacity complete all as as specified and directed.

Supply & fix MCB SPN 32 Amps 10 KA 240 V, 10 KA 'C' Curve complete all as specified and directed.

Supply & fix MCB SP 6 to 32 Amps 10 KA 240 V, 10 KA 'C' Curve complete all as specified and directed.

Supply and fixing decorative LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light fittings mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including conencting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED light fittings 1 x 10 watt bulkhead luminaires including LED light driver holder conencting up with three core flexible copper cable of suitable size complete all as specified and directed.

Supply and fixing in replacement LED luminaire 600 mm x 600 mm,36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light white/warm white/multi coloured (quantity as directed and decided by Engineer in Charge) complete with driver, holders & LED lamp suitable for false ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fix Water heater storage type, electric,capacity 25 litres BEE 5 star rated complete all as specified and directed.

Taking down ceiling fan/exhaust fan 1200mm/1400mm sweep for complete servicing, repair of fan motor and replacement of worn out parts such as bearing, including painting of ceiling fan with synthetic enamel paint by spraying with filling the cavities with filler, one coat after cleaning all dust and writing the MES No and hanging of ceiling fan/exhaust fan in situ , complete all as specified and directed by Engr-in-Charge.

M & L for single pole and neutral enclosure with a two pin earth plug socket complete with one ssingle pole MCB of 20 Amp capacity complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6mm thick burried directly in ground not less that 2.25 m deep below normal ground level and top edge of the plate not less than 1.5 mtrs below normal ground level connected to GI strip of size 25 x 4 mm by means of bolts, nuts, check nuts and washers of GI or steel all as shown in electrical palte No 3 connected to earthing test point incl excavation, earth work in any type of soil strata, PCC chamber, 40 mm dia GI med grade pipe as protection of strip and 15 mm dia GI Med grade watering pipe, funnel, wire mesh etc including testing on completion complete all as specified and directed.

SNEH TRADERS (BID ID -3452087)

Abhishek Enterprises (BID ID -3452293)

Ramdev and Sons (BID ID -3451612)

Shree Builders (BID ID -3452065)

divyarsh entrprise (BID ID -3452559)

K K Construction Co (BID ID -3451620)

Haritwal traders (BID ID -3452010)