SPL REPAIR TO BLDG NO T-259 AND PROVN OF BATHROOM WITH TOILET AND PROVN OF 10000 LTR WATER STORAGE TANK UNDER AGE (I) BHALRA

Amount

Supply and fixing of 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap at least 150mm end lap, fixed with galvanized L-hook or J-hook or cranked hook bolts in lieu of screws in roof walls etc. with grade of zinc coating 275 gm/sqm, complete all as specified.

Dismantling of wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets including removal of Debries outside Cantt area complete all as specified and directed.

Supply and fixing of 4 mm thick non asbestos fiber cement plain building boards in false ceiling on and incl aluminium snap grid work 605 x 605 mm with using 36.5mm x 23.5 mm x 1.5 mm thick main tee, 23.5 x 23.5mm x 1.28 mm cross tee and 25x25x1.5mm angles fixed to perimeter of wall including necessary supporting hanger with 4 mm dia GI wire and J bolts washer nuts for securing frame work to ceiling suspended @ 120 cm c/c both ways, complete all as specified and directed.

Supply and fixing of PVC wall panelling made up of PVC hollow panels 25/30cm in width and 10mm thickness interlocking pattern of approved shade and design fixed to wall or ceiling all as specified and directed.

Supply and fixing of 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

Material and labour for prepration of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

Material and labour for prepration of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified.

Taking down chowkats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

Taking down chowkats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

Supply and fixing of Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

Supply and fixing of Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

Supply and fixing of Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

Supply and fixing of sheet glass ordinary quality, 4.8mm thick, fitted with snap bedding rubber gasket in aluminium doors/windows exceeding 0.50 Square metre in each pane, complete all as specified.

Supply and fixing of 6mm thick, toughned glass fitted with snap bedding rubber gasket in aluminium doors/windows exceeding 0.50 Square metre in each pane, complete all as specified.

Dismantling of plain or corrugated steel sheeting, any guage, thickness, including nainital or similar pattern roof coverings, ridges, hips , valleys and flashings complete all as specified and directed.

Supply and fixing of 0.63mm thick Plain, galvanised, mild steel sheeting in ridges, hips, valleys gutters, drip and straight flashings with grade of Zinc coating 275, complete all as specified and directed.

Supply and fixing of Door closure hydraulically regulated designation No. 3 universal type of aluminium (die cast) body, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kilogam complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) and disposal of unserviceable material, debris and rubbish to a distance not exc. 100m, complete all as specified and directed.

Material and labour for 75 mm thick plain cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in plinth protection and laid in panels complete and finished the even & fair and providings joints through out the thickness of plinth protection filed with mastic filling comprising one part of 01 bitumen 85/25 grade and three part of sand by weight all as specified and directed.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m deep in any type of soil and getting out, complete all as specified and as directed.

Material and labour for PCC 1:4:8 (nominal mix), type D-2 using 40mm graded stone aggregate as in foundations, filling, mass concrete and sub base of floor, complete all as specified & directed.

Material and labour for Stone walling of random rubble with best quality locally available harder stone such as granite, trap or basalt, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6, complete all as specified & directed.

Material and Labour for Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6, complete all as specified.

Material and Labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cementbut using integral water proofing compound as per manufacturer's instructions, complete all as specified. Note : Integral water proofing compound shall be measured & paid seprately.

Material and Labour for rendering 10 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

Material and Labour for preparing new surfaces (plastered or unplastered) of walls and applying two coats of cement base paint over a coat of primer, complete all as specified and as directed.

Material and labour for preparation of new plastered surface of wall and applying three coats of white wash, complete all as specified and directed.

Material and labour for Hard core of gauge not exc 63mm using broken stone or boulders, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface, complete all as specified.

Material and labour for 100mm thick plain cement concrete 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) as in hard standing finished even and smooth without using extra cement including necessary from work, complete all as specified and directed.

Material and labour for 75mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base, complete all as specified and directed.

Material and Labour for 25mm thick plain cement concrete 1:2:4 type B-0 (12.5mm graded crushed aggregate) as in sub base of floors finished even and fair, complete all as specified and directed.

Material and Labour for non skid ceramic coloured tiles 7 to 8mm thick (Square/Rectangular) area exceeding 0.11 sqm but not exceeding 0.18 sqm in floors set and jointed in neat cement slurry over and pointed in white or coloured cement to match the coloured tiles over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

Material and Labour for Glazed ceramic coloured tiles in skirting/dado 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:4 as backing coat rough finished surface complete all as specified and directed.

Supply and fixing of Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified.

Supply and fixing of 3 mm thick sheet glass, ordinary quality & glazing with oil putty/wooden beading/rubber packing around the glass in square n exc 0.5 sq.m in each pane, including hacking out old glass of any description complete all as specified and as directed.

Supplying and fixing of factory made Solid PVC Door Frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S.Square tube, suppling & fixing in opening as per specification complete all as specified and as directed.

Supplying and fixing of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and as directed.

Supply and fixing of Butt hinges of size 100mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21, complete all as specified.

Supply and fixing of Aluminium anodised, barrel tower bolts of extruded section of size 150mm ISI marked and fixed, complete all as specified and directed.

Supply and fixing of Extruded aluminium alloy handles, fabricated type, anodised of size 150mm and fixed, complete all as specified and directed.

Supply and fixing of Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and fixing of Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed in repairs complete all as specified and directed.

Supply and fixing of push botton type dual flush type PVC valve less syphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints, complete all as specified and directed.

Supply and fixing of Vitreous china Wash hand basin, white, flat back of size 550x400mm including cast iron brackets, cutting for and pinning in ends of brackets or erecting stand etc. including brass chromium plated waste coupling with long screwed shank and fly nuts, PVC flexible waste pipe of bore 32mm, complete all as specified and directed.

Supply and fixing of Vitreous china wash down water closet pan pedestal pattern, white (excluding supply of flushing cistern and flush pipes), including making connections to trap, and to flush pipe including plastic seat and cover (as directed ) with stainless steel or aluminised hinging device, complete all as specified and directed.

Supply and fixing of Viterous China urinal, half stall, bowl type flat back, size 430x370x340mm white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement including 32mm bore PVC waste pipe, fixed in repairs, complete all as specified.

Supply and fixing of Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Supply and fixing of Ocean Central hole wash basin mixer (Cera cat part No: F3001461), for mixing Hot & Cold water screwed down for iron pipe of 15mm bore, complete all as specified and directed.

Supply and fixing of PVC connection 15mm size with brass nuts on both ends of length 450mm, complete all as specified.

Supply and fixing of tubular towel rail aluminium anodised 600mm long between flanges fixed with and including chromium plated brass screws and wooden/plastic cleats, fixed in repairs complete all as specified and directed.

Supply and fixing of Bib taps long body 15mm bore (ISI marked) of cast copper alloy, chromium plated , fancy type, screwed down, high presure, screwed both ends for iron pipe or for brass ferrule, complete all as specified and directed.

Supply and fixing of angle or Stop valve (ISI marked) of cast copper alloy, chromium plated , fancy type, screwed down high pressure, screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified and directed.

Supply and fixing of stainless steel soap dish all as specified & directed.

Supply and fixing of Rolled mild steel work in main and cross beams, hip and jack rafters; purlins where connected to comman rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-410-W (Gde E-250) quality A, complete all as specified & directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specified.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified.

Supply and fixing of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge.

Material and labour for RCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc., complete all as specified & directed

Material and labour for RCC 1:2:4, nominal mix, using 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified.

Material and labour for TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, conforming to grade Fe-500, complete all as specified& directed.

All as per Srl item No. 61 above but 5mm dia & over upto & including 10mm dia in stirrups, spacers and binders.

Material and labour for Use & waste of form work to sides of concrete foundation, footings, bases of columns, rafts and raft beamsand similar work; vertical or to batter for rough finished surfaces of concrete, complete all as specified & directed.

Material and labour for Use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beamsfor rough finished surfaces of concrete, complete all as specified & directed.

Supply and fixing of PVC(SWR) pipes 110mm dia bore, single socketd , in any length with rubber ring joints , in any length fixed to walls or laid in trenches or in floors having strength not less then 6kg/cm2 with and including clamps complete all as specified and directed.

Supply and fixing of PVC (SWR) bend any radius 110mm dia bore complete all as specified and directed.

Supply and fixing of PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing with solvent cement, complete all as specified.

Supply and fixing of 15mm dia GI steel water tubing, medium grade ISI marked, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors, complete all as specified.

Material and labour for PCC 1:3:6, type C2, using 40mm graded stone aggregate as in surface channel and drains, complete all as specified.

Material and labour for PCC 1:2:4, type B-1, using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.

Material and labour for Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc., complete all as specified.

Material and labour for precast cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in landings, cover slab (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match, complete all as specified.

Material and labour for PCC 1:3:6 (nominal mix), type C-2 using 40mm graded stone aggregate as in foundations, filling, mass concrete and sub base of floor, complete all as specified & directed.

Material and Labour for Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:4, complete all as specified.

Material and labour for TMT bars 6 to 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, conforming to grade Fe-500, complete all as specified& directed.

Material and labour for concrete bed to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid in cement concret 1:3:6 type C-2 using 40mm graded stone aggregate, and tested, complete all as specified & directed.

Excavation in post holes (or similar holes) each not exc. 0.50 cum, in any type of soil and getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc. 25cm, watering and removal of excavated materials to a distance n. exc. 50m and making good surfaces, complete all as specified & directed.

Supply and fixing of Rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 1000 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and PTMT ball valve 20mm (Minimum weight 210gms), high pressure with polyethelyne float and fly nuts, complete all as specified and directed.

Supply and fixing of Rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 10000 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and PTMT ball valve 20mm (Minimum weight 210gms), high pressure with polyethelyne float and fly nuts, complete all as specified and directed.

Supply and fixing PTMT ball valve 15mm (Minimum weight 210gms), high pressure with polyethelyne float and fly nuts, complete all as specified .

Supply and fixing of 20mm dia GI steel water tubing, medium grade ISI marked, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors, complete all as specified.

Supply and fixing of 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches or in floors having strength not less then 6 kg/cm2 with and including clamps, complete all as specified and directed.

Supply and fixing of 75mm bore PVC (SWR) bends any radius, with or without excess door, complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etcomplete all as specified and directed.

Material and labour for Point wiring with multi stranded copper conductor of size 1.50 Sqmm PVC insulated unsheathed FRLS cable in and including concealed PVC conduit of appropriate size not less than 20 mm dia or as required at site including its fittings and fixtures such as ties, bends, elbows and junction boxes etc. including 1.50 Sqmm copper earth wire (green colour) FRLS Cable as earth continuity conductor connected to main earthing and common earth terminal for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, mild steel or cast iron sunken box including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and directed. (Note : Switch/bell push/fan regulator shall be measured and paid separately)

All as per the description of Serial Item No 85 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 85 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 2.50 Sqm with 2.5 Sqmm copper conductor in green colour for as earth continuity conductor all as specified and directed.

Supply & fixing Switch piano flush type, single pole, 6 Amp, one way, AC 230 volts etc complete, all as specified and directed.

Supply & fixing Socket outlet, 2 in 1, 5 pin, 6 Amp, flush type, AC 230 volts etc complete all as specified and directed.

Supply & fixing switch socket combination 2 in 1, 5 pin, 5 & 15Amp, flush type, AC 230 volts etc complete, all as specified and directed.

Material and labour for Point wiring using FRLSH PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.5 mm thick including all fittings viz tees, bend, junction box and modular metal flush sunken box 1.2 mm thick with suitable support frame and cover plate (inner/outer) of required modules for mounting switches, sockets, fan regulators , connecting earth for light/fan/bell point including cutting chases in walls and making good to disturbed surface complete all as specified and directed . (Note : Switch/bell push/fan regulator shall be measured and paid separately)

All as per the description of Serial Item No 91 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 91 here-in-before but for one 3 pin socket outlet 5 Amp on independent board, complete all as specified and as directed.

All as per the description of Serial Item No 91 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 2.50 Sqm with 2.5 Sqmm copper conductor in green colour for as earth continuity conductor all as specified and directed.

Supply and fixing of modular switch one way 10 Amp, 1 module, complete all as specified and directed.

Supply and fixing of modular socket 10 Amp, 2/3 pin mutipurpose, 2 module, complete all as specified and directed.

Supply and fixing of modular switch piano one way, 16 Amp, 1 module, complete all as specified and directed.

Supply and fixing of modular socket 6/16 Amp, 2/3 Pin multipurpose, 2 module, complete all as specified and directed.

Supply and fixing of Fan regulator modular step type suitable for 1200mm sweep ceiling fan hum free, 120W- 2 module including necessary connections complete all as specified and directed.

Supply and fixing of 20W surface/wall mounted box type batten LED luminaire, extruded polycarbonate housing with PC diffuser and integrated electronic driver with high efficiency long life, CRI=80(Minimum), PF>0.90, luminous efficacy > 120 lumens/Watt operating voltage 140V-240V, colour temperature (CCT) > 5700 + 300K, THD < 10% complete with all accessories internally prewired and including connection up with flexible copper conductor cable of suitable size from ceiling rose to connector of LED fitting complete all as specified and as directed.

Supply and fixing of box type 10 Watt LED 2 feet length as mirror light, extruded polycarbonate housing with PC diffuser and integrated electronic driver with high efficiency long life, CRI=80(Minimum), PF>0.90, luminous efficacy > 100 lumens/Watt operating voltage 140V-240V, colour temperature (CCT) > 5700 + 300K, THD < 10% complete with all accessories internally prewired and including connection up with flexible copper conductor cable of suitable size from ceiling rose to connector of LED fitting complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm, complete all as specified & directed.

Supply and fixing Ceiling rose, 3 phase/PVC/Polycarbonate, isolated body and all as specified and directed by Engr-in-charge.

Supply and fixing in replacement MCB DB 4 - way, single door, 240 volts for Sheet Steel, Phosphatised, Powder Painted MCB DBs with Bus Bar,Neutral Link, Earth Bar and Din Rail (In accordance with IS 13032, IS 8623, IEC/BSEN 60439-3), complete all specified and directed by Engr-in-charge.

Supply and fixing in replacement MCB SP 6-32 Amps 'C' series 240V 50Hz 10 KA suitable for lighting and other domestic loads complete all as specified and directed by Engr-in-charge.

Supply and fixing in replacement MCB SPN 40 to 63 Amps 'C' series 240V 50Hz 10 KA suitable for lighting and other domestic loads complete all as specified and directed by Engr-in-charge

Supply and fixing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminiuum stranded conductor served with an inner sheating of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 mtr apart including 4mm suspention wire one twin core 16 sqmm solid conductor all as specified and directed.

Supply anf fixing of Storage water heater (Geyser), vertical type, of 25 ltr capacity of inner tank, outer tank, syphon assembly, thermostat heating element, safety valve etc complete all as per manufacturer design and specifications including making of all fixing arrangements complete having BEE Five Star Rating including grouting of nuts and bolts and necessary PCC work as specified and directed by Engineer-in-Charge.

M/S SUSHEEL KUMAR Govt. CONTRACTOR (BID ID -3172204)