SPECIAL REPAIR TO BLDG NO 74 (WORKERS CANTEEN) AT ARSENAL OF CAFVD KHADKI UNDER GE (CENTRAL) KHADKI

Amount

B/R PORTION : Dismantling at any height of single layer Mangalore pattern or similar tiles in roof coverings at any height including batten complete all as specified and directed by Engr-in-Charge

Dismantling at any height of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by Engr-in-Charge

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated/corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified and directed by Engr-in-Charge

Dismantling at any height timber scantling 40 sqcm frames works as in fillets, rail , rafter and over in section, in any position repair complete all as specified and directed by Engr-in-Charge

S & F for Rolled mild steel Fe-410- W(Gde E-250) quality B in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engr-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed by Engr-in-Charger

S&F Mild steel, plain 1.25mm thick , black sheet in wall cladding, steel gates, tank staging and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed by Engr-in-Charge

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar in including all quoins, arches, pillars, walls, water staging etc, but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and directed

M & L for Pre-cast cement concrete block masonry Type B1 , 1:2:4 (20mm graded aggregate) set in cement mortar 1:4 with solid blocks, exc. 10 cm in width and setting in mortar, complete all as spd and directed by Engr-in-Charge.

Taking down cement plaster on wall /concrete surface etc including racking out joints hacking for key scrubing down with water etc all as specified and directed

M & L for rendering 20 mm thick in two layers on fair faces on stone/ block masonry surfaces on walls in CM 1:4 finished even and smooth complete all as spd and directed by Engr-in-Charge. (Note: Waterproofing compound paid and measured separately)

Supply only Liquid water proofing compound

M & L for rendering 15 mm thick on fair faces on stone/ block masonry surfaces on walls in CM 1:6 finished even and smooth complete all as spd and directed by Engr-in-Charge.

M & L preparation of New/ old plastered wall surfaces and applying 3mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound distemper over one coat of primer complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new/ old decorated plastered or unplastered surfaces of wall, and applying two coat of cement base paint over a coat of alkali reistant primer complete all as spd and directed by Engr-in-Charge.

Taking down chowkats and frame exc 1.5 Sqm but n.exc 4.00 sqm each including shutter wiuthout taking off shutter from the frame and removing from site complete all as spd and directed by Engr-in-Charge..

S & F for aluminum alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mmx1.25mm, shutter top section 47.62mm x 44.45mmx1.25mm thick, shutter bottom section 114.30mm x 44.45mm x 1.25mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 1.25mm thick & glazing clips weighing not less than 0.097 kg/RM) incl shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/12mm thick prelaminated particle board as required including handles, tower bolt, door stopper complete all as spd and directed by Engr-in-Charge.

S & F aluminium alloy powder coated glazed or skelton shutter including frame of section ( door frame single groove 85mmx45 mm x 1.25mm thick, shutter top section, bottom section, middle section and vertical section 65 mm x 45 mm x 1.25 mm thick and glazing clips weighing not less than 0.097 Kg/RM ) including shutter fixed to frame as directed and as per IS specifications including S & F mild steel wire cloth 0.56mm dia and apperture 1.4mm and required handles, tower bolt,rubber gasket complete.

S&F Door closer hydraulically regulated, Aluminium (extrued section) body designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed

S & F Pressed steel frames made of 1.25 mm thick MS Sheet size 105x60mm for doors, ventilator with single rebates including necessary fixing lugs, hinges, lock strike plate etc, M & L for providing PCC 1:2:4 type B1 (using 20mm graded stone agg) to fill the frame & making good complete all as specified & directed by Engr-in-Charge.

S&F 35 mm factory made shutters of second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated supplied and fitted to chowkat complete all as spd and directed by Engr-in-Charge.

S & F aluminium anodised barrel tower bolts of extruded section and fixed150 mm long complete all as specified and directed by Engr-in-Charge

S & F aluminium anodised handle, oval type, of size 150mm, fixed with screws or welded, complete all as specified and directed by Engr-in-Charge

M & L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as spd and directed by Engr-in-Charge.

Taking down chowkats and frame n exc 1.5 Sqm each including shutter wiuthout taking off shutter from the frame and removing from site complete all as spd and directed by Engr-in-Charge..

S&F aluminium powder coated window sliding type (3 track) with frame size 100x35x1.2mm thick and shutter frame size 39.40x17.70x1.2mm thick with two glass shutter and one mesh shutter including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm thick plain float glass and 0.36mm dia apperture 1.4mm SS wire mesh and fittings etc and making good the jambs and painting with existing surface matching complete all as specified and directed by Engr-in-Charge

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like over 15mm thick cement Screed base in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismantling of existing PCC beds/Granite complete all as specified and directed by Engr-in-Charge

S & F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fix to grill of cooking area complete all as specified and directed.

M & L for preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primere complete all as specified.

M & L for 25 mm thick PCC 1:2:4 type B-1 using 20mm crushed stone aggregate as in leveling course complete.

M&L Glazed ceramic colour tiles in vertical surface 450x350x7mm/ 300x450x7mm/ 300x600x7mm thick with necessary border etc set and jointed in neat cement slurry and pointed in coloured cement to match over including 10mm thick renderting back coating in cement mortar 1:4 including dismantling of old tiles all as specified and directed

M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished of any colour, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick screed bed in cement mortar (1:4) including dismantling of old tiles all as specified and directed

M & L for 20-25 mm thick machine cut kota stone slab over and including 20mm thick screed bed in cement mortar (1:4) with roughening of surface, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as spd and directed by Engr-in-Charge.

S&F in repairs Stainless steel fancy type curtain rod 20 mm including SS brackets, decorative knobs,and including all necessary fittings such as rawl plug screws complete all as spd and directed by Engr-in-Charge.

S&F 15mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floor including taking down old existing complete all as spd and directed by Engr-in-Charge.

S&F 20mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floor including taking down old existing complete all as spd and directed by Engr-in-Charge.

S&F 20 mm dia gun metal ,globe or gate valves , with iron wheel head , screwed both ends for iron pipe complete all as spd and directed by Engr-in-Charge.

S&F in repair 15 mm bore Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule complete all as spd and directed by Engr-in-Charge.

S&F in repair angle cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed Make Prayag Cat Part No :8310

S&F (in repairs) Stop cock (Concealed) cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule with long shank and cup for 15 mm bpre of pipe complete all as specified and as directed.

S&F PVC floor trap in repair square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm,complete all as spd and directed by Engr-in-Charge.

S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge

S&F for 15 mm dia PVC connection pipe 450 mm long with two nuts fly nuts complete all as spd and directed by Engr-in-Charge.

S&F for Angle Stop valve (ISI Marked), fancy type, chromium plated with long shank and cup (concealed type). screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as spd and directed by Engr-in-Charge.

M & L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as spd and directed by Engr-in-Charge.

S&F, in repair kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers & wastes including CI cantilever bracket & connection union to pipe over all size 915mmx460mm & bowl size 410 x330x160mm complete all as spd and directed by Engr-in-Charge.

S&F in repair vitreous china wash basin white flat back size 580x450 mm excluding taps but incl 32 mm dia CP waste fitting and PVC waste pipe 610 mm long and brackets complete all as spd and directed by Engr-in-Charge..

S&F in repair 15 mm bore Pillar taps, cast copper alloy fancy type, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in ground floor or pavings n exc 15 cm thickness (below or above ground level)

M&L 75 mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate laid in panels surface finish even and smooth without using extra cement as in plinth protection and path complete all as specified and as directed.

M & L for 100mm thick PCC 1:4:8 type D-2 using 40mm graded aggregate as in subbase over rammed earth complete all as spd and directed by Engr-in-Charge.

M & L for 25mm thick crushed stone dust/sand filling under floors or in foundations including watering and consolidation complete all as spd and directed by Engr-in-Charge.

M & L for Coloured Machine pressed precast concrete interlocking paver block glossy finished (Two colour combination) any shape and size confirming to IS 15658-2006 of 60 mm thickness M-40 Grade with grey cement and pigment laid over sand cushion including demolition complete all as spd and directed by Engr-in-Charge.

S&F 3 layered rotational moulded polyethylene water storage tanks capacity 1000 lit in ( cylindrical vertical with closed top ) hoisted and fixed in position including dismantling and removing of old tank complete all as spd and directed by Engr-in-Charge.

M& L for RCC(Nominal mix) type B1, (1:2:4) 20mm graded aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as spd and directed by Engr-in-Charge.

M& L for Formwork to chullah hoods, cha jjas, troughs, shelves and similar items in cluding edge vertical or to batter for fair finished surfaces

M & L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for footings, foundation, columns, shelves, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to TMT steel of grade Fe 500/Fe 500 D/Fe 550/ Fe 550 D meeting all requirements of IS

S & F Gypsum reinforced boards 600x600x8-10mm thick for ceiling hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4mm dia to be fixed by approved rawl plugs, level and justers and screws etc, The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm from adjacent center to form 1200x600mm moulds cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross tee centrally between the 1200mm cross tee. Tee perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instructions and finishing the surface by applying two coats of plastic emulsion paint complete all as directed.

E / M PORTION : Taking down carefully existing unserviceable aluminum / copper point wiring of any description & in any position with and including existing steel conduit / PVC Conduit / Casing caping fixed on surface/wall/angle/gardder and including all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, sockets, etc including sunken boxes/junction boxes and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as spd and directed by Engr-in-Charge.

M&L for point wiring in PVC coduit of suitable size but not less than 20mm including all fittings such as elbow, bends, junction boxes, saddles, etc. on surface with and including ISI marked two runs of PVC insulated unsheathed multistranded copper conductor cable (FRLSH) 1.5 sqmm nominal cross sectional area, 1100 volts grade and including one run of 1.5 sqmm (green colour) ISI marked PVC insulated unsheathed multistranded (FRLSH) copper conductor cable as earth wire to be terminated in and incl PVC rectangular block of suitable size for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover for one light point or one fan point controlled by one switch including making good the disturbed wall and painting the same with matching to existing wall complete all as spd and directed by Engr-in-Charge.

All as per Srl item No 2 above but point wiring for 5 pin socket outlet, 5 Amps on same board with other switchescomplete all as spd and directed by Engr-in-Charge.

All as per Srl item No 2 above but point wiring for 5 pin socket outlet, 5 Amps on independent board complete all as spd and directed by Engr-in-Charge.

All as per Srl item No 2 above but point wiring for one five pin socket outlet, 15 Amps & 5 Amp on independent board using 2.5 sqmm two run and one run 2.5 sqmm (nominal area) stranded copper conductor cable.

S&F for switch flush type, 5 Amps, single pole, one way , 230 volts AC circuit complete all as spd and directed by Engr-in-Charge.

S&F for socket outlet, five pin, 5 Amps, flush type, multipurpose, 230 volts AC circuit complete all as spd and directed by Engr-in-Charge.

S&F for switch flush type, 15 Amps, single pole, one way , 230 volts AC circuit complete all as spd and directed by Engr-in-Charge.

S&F for Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type , flush type, 230 volts AC circuit complete all as specified & directed

S&F for ceiling rose PVC/polycarbonate, isolated body, three terminals, complete all as specified & directed .

S&F in replacement Stepped type electronic fan regulator flush type suitable for ceiling fans, prewired 230 volts AC 50Hz supply 100Watt complete all as spd and directed by Engr-in-Charge.

Dismantling and Taking out old unserviceable copper/aluminium sub main wiring/Unarmoured cable (used as Sub main wiring) from any height of any Size and Core with all connecting accessories incld. conduit or casing caping and incld. making good to the disturbed wall and painting the same with matching paint as of existing wall including material all as specified and directed by Engineer in charge.

M & L for Sub main wiring at any height and surface with and including two single core PVC insulated multi stranded copper conductor cable, conforming to IS, FRLSH type, 4.0 Sqmm, 1100 volts grade, drawn through and including New PVC non metallic conduit 20 mm dia including connected accessories and one single core PVC insulated multi stranded unsheathed copper conductor cable, FRLSH type, 4.0 sqmm, 1100 Volts grade,,green in colour as earth contuinity wire all as specified and directed by Engineer in charge.

Disconnecting and taking down old switch fuse type distribution Box with MCB/fuse grip TPN/SPN DB 2 Way to 12 Way old type DB including taking out all cable connections of any description and in any position and M&L for making good the disturbed surface of walls, to match with the existing surfaces complete all as specified and directed by Engineer in charge.

S&F for connecting & testing SPN DBs of 8 way for using MCBs / MCB isolators suitable for single pole and neutral, with IP 43 -IK09 as conforming to IEC 61439-3 & made of high quality CRCA sheet shall have integrated door earthing system, DB shall be with Insulated Busbar with withstand capacity of 10kA, shrouded neutral bar, Door earthing, corner Safe. wiresets, shrouded Neutral bar, earth bar & wire ties, all as specified & directed of Make Legrand Cat.No. 507611 or equivalent make.

S&F for MCB 6 to 32 Amps, single pole and neutral, "C" curve 10 kA breaking capacity with integrated label holder, sliding bottom clamp, color coded On/Off indication on dolly complete all as spd and directed by Engr-in-Charge.

S&F for MCB 6 to 32 Amps, single pole, 10 kA breaking capacity with integrated label holder, sliding bottom clamp, color coded On/Off indication on dolly,complete all as spd and directed by Engr-in-Charge.

Dismantling and Taking down unserviceable existing light fittings 1X 40 Watt / 2X 40 Watt/ 70 watt or any other wattage security lihgts of any size and capacity from any location/height after disconnecting of electrical connection complete including all connected accessories all as directed by Engr-in-Charge.

Supplying, fixing, connecting up to existing/new ceiling rose and testing industrial box type batten with precoated CRCA body. LED tube light fitting suitable for and including 2x20 W 4 feet long tube with polycarbonate diffuser ,LED lamp efficay -110 Lum/W ,THD ≤15% with operating voltage range 100-300V, driver efficency >85%, surge voltage withstand 2.5 KV , power factor ≥0.9 including complete all as spd and directed by Engr-in-Charge.

Supplying, fixing, connecting up to existing/new ceiling rose and testing industrial box type batten with precoated CRCA body. LED tube light fitting suitable for and including 1x20 W 4 feet long tube with polycarbonate diffuser ,LED lamp efficay -110 Lum/W ,THD ≤15% with operating voltage range 100-300V, driver efficency >85%, surge voltage withstand 2.5 KV , power factor ≥0.9 including connecting complete all as spd and directed by Engr-in-Charge.

Replacment of ceiling fan 1400 sweep complete all as spd and directed by Engr-in-Charge.

Replacment of heavy duty exaust fan 450 sweep complete all as spd and directed by Engr-in-Charge.

Supplying, fixing, connecting up to existing/new ceiling rose and testing 36 W aesthetically designed 2x2 LED recess mounting in grid/armstrong type ceiling including suitable LED driver and connecting with 23/0.0076 copper conductor flexible twisted two core cable to existing/new ceiling rose and including mounting accessories complete all as spd and directed by Engr-in-Charge.

MAHABIR INDUSTRIAL PRODUCTS (INDIA) (BID ID -3059502)

M/S KISHAN CONSTRUCTION (BID ID -3059442)

S P DEVELOPERS (BID ID -3059150)

AJINKYA VIKRAM GAIKWAD (BID ID -3055420)

M/S JAYCONSTRUCTION CO (BID ID -3067730)

greenstone construction (BID ID -3058741)