Construction of Lac Value Addition Training Center Cum Administrative Building at Sidroll, Ranchi

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:3:6 (1 cement : 3 coarse sand (zone - III): 6 graded stone aggregate 20mm nominal zie)

Providing designation 75 A brick work in C.M.(1 :6) in foundation & Plinth with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"X4.5"X3") in C.m. (1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I

Providing designation 112mm thick reinforced designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"X4.5"X3") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints tom 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

Extra for brick work for EACH consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

Second floor

Third floor

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering and shuttering, finishing and reinforcement - all work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone - III): 3 graded stone aggregate 20mm nominal zie)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases, above plinth level upto floor five level, excluding the cost of cenetering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone - III): 3 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and structs etc. above plinth level upto floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 1:1.5:3 (1 cement : 1.5 coarse sand (zone - III) : 3 graded stone aggregate 20mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Providing tor steel reinforcement of 8mm. dia. rods as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position (excluding carriage of bars to work site) all complete as per building specification and direction of E/l. TMT FE 500 ( only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd. Bokaro, & Vizag (RINL)

Providing tor steel reinforcement of 10,12,16mm . dia. rods as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position (excluding carriage of bars to work site) all complete as per building specification and direction of E/l. TMT FE 500 ( only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd. Bokaro, & Vizag (RINL)

10mm dia -

12 to 25mm dia

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing & fixing pressed steel door frames manufactured from commercial mild steel sheet of 1.25mm thickness including hinges ,jamb, lock jamb, bead and if requiredangle threshold of mild steel angle section 50 X 25mm, orangle threshold of mild steel angle section 50 X 25mm, orbase ties of 1.25mm pressed mild steel welded or rigidlyfixed together by mechanical means, adjustable lugs withsplit end tail to each jamb including steel butt hinges split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and 2.5mm thick with mortar guards, lock strike-plate andshock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by the Engineer Incharge - Profile - B - Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. compelte - 2nd class teak wood - 50X20mm

Providing and fixing 1mm thick M.S. sheet door with frame of 40X40X6mm angle iron and 3mm M.S. gusset plates at the junctions and corners all necessary fittings complete, including applying a priming coat of approved steel primer - using M.S. angles 40X40X6mm for diagonal braces

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinfoorced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Enginner-in-Charge.

30mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm . 19mm for styles and 15x15mm for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on eigher side forming styles: and 5 mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mmshall be tapered in 45 degree on the inner side to form top and bottom raiil and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail.

Top, bottom and lock rails shall be provided eigher side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded / sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer's specificatio n& drawing (for W.C. and bathroom door shutter).

providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) tramsparent or dyed to required colour or shade with necessary screws etc. complete 125X75X4mm

Providing and fixing luminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transpoarent or dyed to required colour or shade with necessary screws etc. complete 150X10mm

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or deyed to required colour or shade with nuts and screws etc. complete 250X16mm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling C.P. brass / stainless steel screws, all complete as per architetural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately)

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required inlcluding the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for separately) --- Polyester Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator, shutters and partitions etc, with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4mm thickness (weight not less than 10kg/sqm.)

With float glass panes of 8mm thickness (weight not less than 10kg/sqm.).- (Aluminium door).

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by deptt.)

Providing and fixing stainless steel (grade 304) railing made of Hollow tubes, channels, plates etc,. Including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessry stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasterners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc,.) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and laying Doublecharge Vitrified floor tiles in different sizes (thickness to be specificed by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622/ISO 13006 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete size of tiel 600X600mm

Providing and laying rectified glazed ceramic floor tiles 300x300mm or more (thickness to be specified by manufacturer) of 1st quality conforming to IS:15622 with approved make in all colours,shades,except white, ivory, grey, fume red, brown laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3 Kg/sqm. including pointing the joints with white cement and matching pigments, etc.complete.

Providing and fixing 18mm thick gang saw cut mirror polished (premoulded & prepolished) machine cut for kitchen platform and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite slab

Providing edge moulding to 18mm thick marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge Granite work

Providing and laying 25mm thick kotah stone slab flooring of approved size, texture and colour over 19mm thick base of lime mortar (1:1:1) (1 lime putty sucrkhi coarse sand) laid over and jointed with grey cement slurry mixed with pigement to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. - 600 X 600mm size

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/l. With "A" grade white 15 x 15 cm tiles.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grde made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand, filling the joints with coarse sand etc. all complete as per the durection of Engineer-in-charge.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc, all complete as per direction of E/I.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc,. Including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete - Hot finished welded type tubes

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified

Providing and fixing false ceiling at all height including of frame work made of special sections power pressd from M.S. sheets and galvanized with zinc coating of 120gms/sqm (both side inclusive) as per IS 277 and consisting of angle cleats of of size 25mm wide X 1.6mm thick with flanges of 27mm and 37mm at 1200mm centre to centre. one flange fixed to the ceiling with dash fastener 12.5mm dia X 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of 25X10X0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate GI channels 45X15X0.90mm running at the spacing of 1200mm centre to centre.

to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm dia X 230mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long the perimeter of ceiling gixed to wall/partition with the help of rawl plugs at 450mm centre with 25mm long dry wall screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 X 25mm at 230mm c/c including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes,

finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specirfication and also including the cost of making openings for light fittings, grills, diffusers cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in charge but excluding the cost of painting with:

Fully perforated Gypsum Plaster Board of size 1200X2400X12.5mm having approx 15% perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60 (or as per available size)

Providign and applying Plaster of Paris Putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered syrface bv rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, sacffolding washing of floors and taxes all complete as per building specification and direction of E/I,

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with premium acrylic smooth exterior paint with sillicone additives of requited shade . New work : 2 or more coats applied @1.43 Ltr/10sqm over and including base coat of waterproofing cement paint applied @2.2 Kg/10 sqm

Providing French spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including cleaning the surface after removing dirt, scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specifcation and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing & laying water proofing treatment in sunken portion of WCs, bathrooms etc. by applying cement slurry mixed with Armourcrete of M/S The Structural Water Proofing Company PVT. Ltd.or Tapecrete of M/s CICO Engg. Servce consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with Armourcrete or Tapecrete @ 0.125 kg/ sq.m. This layer will be allowed to air cure for 4 hours

(b)second layer of slurry of cement @ 0.242 kg/sqm mixed with Armourcrete or Tapecrete @ 0.126 kg/ sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preperation of surface, treatment& sealing of all joints, corners, junctions of pipes & masonary with polymer mixed slurry.

Providing 1.5mm cement punning including curring, carriage of water with all leads and lifts as per building specification and direction of E/I.

Water proofing for old and new roof slab - Providing and laying water proofing treatment on roof slab by applying two component, factory designed, ready to use acrylic modified flexible material applied with brush roller or spray for water proofing coating as per manufacturer specifications with gollowing steps:

a. Surface preparation - Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint/coating and cement laitance by cleaning with compressed air & water jet including all matrials, labour, tools, complete, ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage leakage. On identification of seepage cement grouting to be done with non shrink expanding adminxture of Sika India Pvt Ltd./MYK schomberg/Dr. Fixit/Fosroc or equivalent. Providing and repairing of all corners and joints such as those between the parapet wall and the roof slab etc. sahll be chamfered with 150mm X 150mm fillet of mortar (cement, sand 1:4) admixed with acrylic polymer of Sika/Fosroc/MYK scholmberg/Dr fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer, Repairing surface irregularities, damaged concretein base slab dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.

b. 1st coat -Apply 1st coat of two component acrylic modified, ready to use flexible cementitious material on surface saturated dry roof and inside wall of parapet wall upto 600mm by brush or roller. After 1st coat of application, 45 gsm of fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @ 1.50kg/sqmt/coat. Fore the prupose of measurement the entire treated surface will be measured.

c. 2nd coat - To apply the 2nd coat of two component acrylic modified, ready to use flexible cementitious material on right angle to the 1st coat over the glass fibre laid surface 2nd coat should be applied @ 0.7kg/sqmt/coat. For the purpose of measurement the entire treaed surface will be measured After three days of drying the 2nd coat, the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The water proof coating to be protected from damage before screed over it. Water proofing brand Sika Topseal 109hi/Fosroc Brushbond RFX/Dr Fioxit Pidiffin 2K/MYK Aquafin TG. Product performance- Chemical base part A Acrylic copolymer, Part B Specially graded cementitious powdere density 1.6 kg/I (mixed density) at +27 degree C. Tensile strength - 2N/mm2 after 28 days (with fibre cloth) (according to ASTM D 2370) Pullout bond strength - 2 N/mm2 (concrete failure) (According to ISO 4624) slant-shear bond strength - 4N/mm2 (according to FIP 5.15) Elongation at break - 35% without fibre cloth and 20% with fire cloth (according to ASTM D 2370)

d. Protection of treated surfaces with PCC ; The treated syrface shound be covered with 25mm/50mm PCC of M-20 grade (1:1.5:3) with proper slope (1:120) towards the rain outlets in alternate panels of 2 mt X 2 mtr. Keeping 6mm gap between the panel joint integral water proofing admixture conforming to IS 2645 @ of 100ml per bag of cement to be added in the screed concrete (Paid separately for this items) All corners shall be chamfered with 150mm X 150mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - peripherial gaps between PVC pipe outlet and concrete surface should be packed properly with rich concrete nd the peripherial mouth to be sealed with mosture insensitive epoxy putty of sika India Pvt. Ltd/MYK schomberg/Dr. Fixit/Fosroc. For purpose of measurement the entire treated surfaces will be measured e, Grooves of PCC surface should be filled with polysulphide sealant. Brand - Sika India Pvt. Ltd. /MYK Schomberg/Dr. Fixit/Foscroc warranty for five years.

Covering of treated surface with PCC - Providing 25mm thick Cement Concrete M-20 (1:1.5:3) maintaining slope in alternte 2 mt X 2 mt panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering, and mixing cement concrete in mixer with adminxture of integral water proofing and placing in position striking curing, taxes and royalty all complete as per building specificastion and direction of E/I. Panels that has been left should be casted next day. There should be 6mm gap between panels brand - Sika-Plastocrate plus, MYK proof WP 10, Fosroc - Conplast X 421ic, Dr. Fixit pidiproof LW+

Providing and filling 6mm thick groove between 25mm PCC panels with polysulphide sealant (Poring Grade) as per drawings and technical specifications and direction of E/C (with 18%GST) brand - Sika-Polysulphide, Fosroc-Thioflex 600, Dr. Fixit Piddiseal PS (42P) MYK seal PS or equvalent

Providing & fixing on wall face unplasticised- Rigid PVC pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion, . (i) Single socketed pipes. 110 mm dia

Providing and fixing on wall face unplasticised- PVC moulded fitting / accessories for unplaqsticised-PVC rain water pipes confirming to IS: 13592 Type A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion.

Bend 87.5 degree - 110 mm bend

Shoe (Plain) 110 mm shoe

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means 50X50X50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete - 110mm

Providing 250 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 250 mm apron including cost of earthwork involved with 75m cement concrete (1:4:3) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing & injecting chemical emulsion for pre-construction Anti-termite treatment and creating a chemical barrier under and all around the coloum pits,wall treanches,basement excavation, top surface of plinth filling,junctions of wall and floor along the external perimeter of building with approved chemical as per IS code As per specification and direction of E/I.

Carriage of materails

Bricks - Lead - 8km.

Sand - Lead 15km

Chips - Lead 15km

Metal - Lead 15km.

Fly Ash bricks (15km)

Earth - Lead - 2km

Dismantling pucca brick or lime work including stacking serviceable matrials in countable stacks within 15M lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down old door window shutters including stacking serviceable materials in countable stacks within 15M lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down choukhats in doors including stacking serviceable materials in countable stacks within 15M lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down choukhats in windows including stacking serviceable materials in countable stacks within 15M lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling of flooring including stacking serviceable materials in countable stacks within 15M lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15M lead and disposal of unserviceable materials with all leads all complete as per diretion of E/I.

Dismantling steel work manually/by mechanical means in built up sections without disembering and stacking within 50M lead as per direction of E/I.

Taking down wooden CA or GCI sheet in roofs with ridges including stacking the serviceable materials within 15M lead and disposal of unserviceable materials with all leads as per direction of E/I.

Supplying, fitting and fixing C.I. cover with frame for manhole &ninspection chamber 600X450mm (wt. not less than 25kg) all cost complete as per direction of E/I

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25 of size 1000X450X50mm reinforced with 8mm dia four nos longitudinal & 9 nos. cross sectional TMT hoop bars, including providing 50mm dia perforations @ 100 to 125mm c/c. including providing edge binding with M.S. flats of size 50mm X 1.6mm complete all as per direction of E/I.

Supplying, filling, spreading & levelling stone boulders of size range 5cm to 20c, in recharge pit in the required thickness for all leads & lifts all complete as per direction of Engineer-incharge

Supplying, filling spreading & levelling gravels of size range 5mm to 10mm in the recharge pit over the existing layer of boulders in required thickness for all leads and lifts all complete as per direction of E/i.

Supply, assembling, lowering and fixing in vertical position in borewell/recharge pit unplasticized PVC medium well casing (CM) pipe of required dia conforming to IS : 12818 including required hire and labour charges, fittings & accessories etc. all complete for all depths as per direction of Engineer-in-charge 150mm nominal size dia

Costs of drilling 200mmX165mmX125mtr. Deep borewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH rig machine, all complete including supplying all materials, tools, drilling rig, Air compressor and equipments, as well as fuel lubricants and cost of transportation of rig machine and other vehicles upto the site From 0-50 mtr.

Providing and fixing ball plug/bottom plug of required dia to the bottom of pipe assembly of tubewell/recharge pit as per IS:2800(part 1) 150mm dia

Supplying, fitting and fixing 125mm dia UPVC pipe of approved quality and make - basic rate + 30% for C.P. and laying charge

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry hindustan or any other ISS approved make with 100mm HCI p trap 15 litres CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings CI or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brass coupling and clamps GI chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixed in floor 15mm CI body brass spindle stop cock of weight not less than 50 grames 15mm PVC connection pipe 450mm long and coat of red oxide primer etc all complete as per specification and direction of E/I. (A) 580 mm long with 12.5 litre low level PVC cistern

Supplying, fitting and fixing 40 mm high vitreous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (i) With "P" trap (b)12.5 lit. low level P.V.C. cistern

Supplying, fitting and fixing flat back or angular lipped front vitreous white glazed earthern ware urinal of Hindustan "Parry" or any other approved I.S.S. make with 5 ltrs. capacity C.I. automatic flushing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S. brackets standard size G.I. flush pipe with fitting clamps 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 gms. 15mm PVC alkathene pipe 450mm long with brass coupling at both ends and doing plumber points including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc. all complete as per speciifcification and direction of E/I. (a) Flat back or standing corner (600mmX350mm)

supplying,fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S approved make supported on painted C.I. or R.S. bracket 32mm C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm PVC waste pipe 750mm long with brass coupling with one end and making plumber joints etc.all complete as per specification and direction of E/I.

Providing and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I.

20mm dia.

25mm dia.

32mm dia

40mm dia

Providing and fixing brass stop cock of approved quality all complete as per specification and direction of E/I. (a) 15mm dia.

Cutting drain width wise above G.L. for laying PVC pipe and restoring brick work in cement mortar (1:4), 12mm cement plaster in C.M. (1:4) with neat cement punning as per specifciation and direction of E/I. (PVC 110mm dia)

Making holes in wall for laying PVC pipes and restoring the same after pipe laying as per specifciation and direction of E/I. (PVC pipe 110mm dia)

Supplying all tolls and labour and cutting chajja cornice for laying PVC pipes and making good the same as per specification and direction of E/I. (110mm dia PVC pipe)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E/I. (all rates have been adopted from the basic rate from SOR + 10% for labour and Contractors profit).

Pillar cock (long neck)

Bib cock - long thread

Angular stop cock L.T.

4 way diverter for concealed fittings (Basic rate Rs.1911.80 + 10% for C.P. & laying charge).

Glass shelf 22" (Basic rate Rs.641.25 + 10% for C.P. & laying charge).

Flush valve complete with 32mm size control cock & flange

32mm dia. PVC waste pipe 750mm long with coupling

15mm C.P. nipple with coupling

100mm dia Steel jali - .

Providing Solvent cement

Supplying, fitting and fixing Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. (i) 600 X 450mm.

Supplying, fitting and fixing C.P. brass towel rail 20mm X 600mm with bracket container.

Supplying, fitting and fixing C.P. brass soap dish container medium quality with screw and hinges etc.

Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc. all complete as per specification and direction of engineer-in-charge.

Supplying, materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. Cover with frame (weight not less than 36kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931, 15mm nominal bore.

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.15 mm nominal bore, weighing not less than 32 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1Mtr. spacing. This includes jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc.

20mm nominal outer dia pipes

25mm nominal outer dia pipes

32mm nominal outer dia pipes

External work - 40mm nominal outer dia pipes

Providing & fixing on wall face unplasticised - Rigid PVC pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion.(i) Single socketed pipes.110 mm dia

Providing and fixing on wall face unplaqsticised- PVC moulded fitting / accessories for unplaqsticised PVC rain water pipes confirming to IS: 13592 Type A, including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion.

Single Tee with door

Bend 87.5 degree

110 mm bend

Providing and placing on terrace (at all floor levels) Polyethylene water storage tank ISI 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing Pressure adjustable shower with revolving joint

Supplying, fititng and fixing stainless steel A ISI 304 (18/8 Kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets cutting and making good the walls wherever required - Kitchen sink without drain board - 610X510mm bwl depth 200mm

Cutting chajjas or concrete for laying PVC Pipe and restoring the same with R.C.C. (1:2:4) brick work in cement Mortar (1:4) and cement plaster 1:4 as per specifiction and direction of E/I

Making holes in walls for PVC Pipe and restoring the same atfer pipe Laying (b) 250mm thick wall

Supplying and fixing PVC fittings of approved make confirming to IS : 1729 including supplying nails and bobbins, fixing solutions including earth work or masonary work cutting and remaking and providilding as the case may be all complete as per specification and direction of E/I.

PVC single junction with door and ear 100mm dia.

PVC cowl - 100mm dia.

Floor trap - 100mm dia.

Single pushfit coupler

Lubricant

Door piece

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.

S/F Light Plug Point with Modular Type Accessories: Supplying and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

S/F Power Plug Point with Piano Type Accessories: Supplying and Fixing suitable size GI box with modular plate cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

S/F 20 amps SPN MCB Industrial Socket Outlet: Supply and fixing 20 amps, 240 volts, SPN insustrial type, socket outlet, with 2 poles and earth, metal enclosed plug top along with 20 amps 'C' series, SP MCCB, in sheet steel enclosure, on surface or in recess with chained metal cover for socket outlet and complete with connections, testing and commissioning etc as required.

Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sq.mm + 1x1.5 sq.mm earth wire

2x2.5 Sqmm + 1x2.5 sq mm earth wire

2x4.0 Sq.mm + 1x4.0 sq.mm earth wire

4x6.0 Sq.mm + 2x6.0 Sq.mm earth wire

S/F T.P. MCB DB:- Supplying and fixing of following way, three pole and neutral, sheet, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (But without MCB/RCCB/Isolator).

4 Ways (4+12),Double door, Horizontal type

S/F 'C' series MCB:- Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32 amps, Single Pole

6/32 amps, TPN MCB

63 amps, TPN MCB

S/F Ceiling Rose: Supplying and fixing 2 pin 5 amp. ceiling rose on the existing junction box/ wooden block including connection etc as required.

ITC fluorescent fitting directly on surface :- installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, directly on ceiling / wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper cond.

S/F Modular type electronic fan regulator:- Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F Batten / Angle Holder: Supplying and fixing batten / angle holder including connection etc as required.

S.I.T.C of following rating surface mounted LED tube light fittings suitable for 230V, 50Hz, single phase supply etc. complete as required - 20/22W. LED tube light

Bulk head fitting with 9/10Watt CFL/LED

Supplying, 15/16 Watt LED bulb of approved make

Supplying Exhaust fan of 12" (300mm) of aproved make

Supply, installation, testing and commissioning of following size ceiling fan 3 blades confirming to IS:374:2019 including wiring the down rods of standard length (upto 30cm) with 1.5sq.mm. FR. PVC insulated copper wire suitable for 230V, 50Hz, single phase supply etc. complete as required. - 1400mm (56") ceiling fan

S.I.T.C. of following rating recess/surface mounted LED round/square shape down light luminaire with pressure die cast housing for single phase supply Voltage. Luminaire shall be confirm to IS:10322 Part -5/section 2 of IEC:62722 with all necessary accessories as required - 18/20W LED round down light

S.I.T.C. of following rating LED street lighting luminarie die cast housing and toughened glass cover (IP-66 portion) in existing pole/pipe for supply voltage 100-270V. AC, 50Hz. Luminaire shall be confirm to IS:10322 part - 5/section 3 and shall be complete with all necessary accessories as required - 60W LED street light

S.I.T.C. of following rating recess/surface mounted LED round/square shape down light luminaire with pressure die cast housing for single phase supply Voltage. Luminaire shall be confirm to IS:10322 Part -5/section 2 of IEC:62722 with all necessary accessories as required - 15/16W LED round down light - as CL

GI Earth Pipe Electrode: Earthing with G.I. earth pipe 4.5 mtr long , 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcol and salt complete as required.

Supplying and nlaying 25mm X 5mm G.I. strips at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required (jointing shall be done by overlapping and with 2sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25mm x 5mm G.I. strip on surface or in recess for connection etc. as required

Provioding and laying 1.1 KV grade aluminium armoured electrical cable as per IS:1554 (Part I) heavy duty all cost complete including cost of brass compression gland, cable jointing and end termination as per specification and direction f E/I.

3.5 core,95sq.mm

3.5 core, 50 sq.mm

Cost of drilling 200mmX165mmX125mtr. Deep borewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH Rig machine, all complete including supplying all materials, tools, drilling rig, Air Compressor and equipments, as well as fuel, lubricants and cost of transportation of Rig Machine and other vehicles upto the site.

From 0-50 mtr.

Above 50 mtr.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia conforming to IS : 12818, including required hire and labour charges fittings & accessories etc. all complete for all depths, as per direction of Engineer-in-charge - 200mm nominal size dia

Gravel packing in tube well construction in accordance with IS : 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge

Development of tube well in accordance with IS 2800 (part 1) and IS: 11189 to establish maximum rate of usable water yield without sand content (beyond permissible limit) with required capacity air compressor, running the compressor for required tile till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, colleting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete including hire & labour charges of air compressor, tools & accessoires etc. all as per requirement and direction of Engineer-in-charge.

Providing & fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe, removable as per requirement, all complete for borewell of 200mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS:2800 (Part-1) including necessary bolts & nuts of required size complete

Providing and fixing Bail plug /Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS :2800 (Part-1). 200mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement trenching, refilling & testing of joints complete as per direction of Engineer in charge

50mm nominal outer dia pipes

Supplying Submersible pumps sets confirming to IS:8034 and motor confirming to IS:9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller.Motor suitable for working on 415V+10%, 3PH, 50Hz, A.C. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shal be suitable for direct couplings. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 mtr. submrsible copper conductor cable in single/ double run shall be provided with each pump.

Submersible pump set 100mm dia (with Polypropylene/noryl Impeller) upto 20 stages - 3.0 HP

NON SCHEDULED ITEMS

Providing and fixing of 3D Lite Panel System of 22 mm thick (minimum) with both the outer walls in clear colour and middle cells shall have the alternate horizontal walls in co-extruded white or approved colour. Panels shall be fixed on purlins with Z type Stainless Steel Fastner using minimum 3 self drilling screws. Panel shall be 600 mm wide manufactured with vertical standing Seam of 15 -20mm height at both sides of the panel (welding or gluing of up standing seam is not acceptable). Panels shall be secured with snap on connectors to interlock the panels shall have 2-4 tooth locking system to ensure best performance against wind uplift or hurricane. Polycarbonate Panel system shall also include Aluminum profiles in natural mill finish for end closure.

Panel shall be manufactured in a manufacturing facility with approved quality assurance procedure as per ISO 9001 & ISO 14001. Panel manufacturer shall provide warranty against any manufacturing defects for a period of 10 years (minimum) and should have a successful project reference in Indian sub-continent which is at least 10 years old for a single project not less than 1500 SQM. Panel shall be installed as per the approved drawings, specifications and as directed by the Engineer-in-Charge.

Providing and fixing high quality Vertical blinds of Vista or equivalent of approved colour and make with necessary fittings all cost complete, as per direction of E/I.

Fabrication, assembling 200A HRC TPN switch incoming and 100/63A TPN, 35KA MCCB outgoing 4 nos. lighting LT electrical sub distribution control panel with the foloowing accessoires:

Supplying, fiting and fixing of the following furntures with superrior quality, all cost complete:

complete set of desktop computer with CDC processor, 1 TbHDD, 4 GB Ram, Keyboard and mouse, with 20" monitor. Providing Winner 5 table with 25mm tabletop supported on 25mm thick gable ends and 18mm thick modesty panel of size 1500mm x 750mm x 750mm ht having a single drawer unit. 1 no. metal keyboard tray and 1 no. PVC CPU Trolley to be included.All edges to be finished with 2mm thick PVC edgebanding. IGBC, BIFMA and ISO certified. Design: HNI make or equivalent

Home theatre and projector with the following accessories and quantities

6Watt Ceiling Mount Speaker Make: Bosch

Plena Mixer & Amplifier with Bluetooth & USB Make: Bosch

4000 ANSI Lumens WXGA Projector with contrast ratio as 20000:1, Full-HD video display. Make: BenQ

Q-Cast Mirror for Wireless Connectivity of Projector. Make: BenQ

Projector Ceiling Mount Kit.

4U Network rack with PDU for Amplifier.

Audio Cable for Projector

Supplying, fiting and fixing of the following furntures with superrior quality, all cost complete:

Supplying, fiting and fixing of the following furntures with superrior quality, all cost complete:

Certo chair Providing Certo Mid Back Chair having adjustable lumbar support, back mesh and seat in cushion. The chair will be supported on 5 star black nylon base and armrests will be 1-D adjustable. The chair should have synchro-tilt mechanism. Seat dimensions will be 520mm depth, 500mm width and adjustable height of 435-535mm. IGBC, BIFMA and ISO certified. Design: HNI make or equivalent

Director chair - Verta HB with headrest Providing Verta High Back Chair having adjustable lumbar support, back mesh, headrest in mesh and seat in cushion. The chair will be supported on 5 star polished aluminium base and armrests will be 4-D adjustable and it should have adjustable seat depth. The chair should have weight activated mechanism. Seat dimensions will be 415-465mm adjustable depth, 480mm width and adjustable height of 410-500mm. IGBC, BIFMA and ISO certified. Design: HNI make or equivalent

Providing 16 seater U-shaped KD fitting conference table of total size: 8400 x 1050 x 730mm ht. Worktop to be made of 25mm thick PLB supported on 25mm thick gable ends and 18mm thick modesty panel. All edges to be finished with 2mm thick PVC edgebanding. 300mm access flap provided on each worktop. 8 nos. of 1350 x 600 x 730mm ht to be supplied for each arm making up the total length. IGBC, BIFMA and ISO certified. Design: HNI make or equivalent.

Gale Visitor chair Providing Gale Visitor Chair having adjustable lumbar support, back mesh and seat in cushion. The chair will be supported on cantilever base and armrests will be fixed. Seat dimensions will be 510mm depth, 510mm width and adjustable height of 495-595mm. IGBC, BIFMA and ISO certified. Design: HNI make or equivalent

Supplying, fitting and fixing approved make White board of approved quality

Providing KD fitting table with 25mm tabletop supported on 25mm thick gable ends and 18mm thick modesty panel of size 1350mm x 750mm x 750mm ht with return combo storage having 3 drawer and 1 shutter of size 900 x 450 x 750mm ht. All edges to be finished with 2mm thick PVC edgebanding. IGBC, BIFMA and ISO certified. Design: HNI make or equivalent

Providing Sonoma Single bed of CRCA metal structure with metal base supported on four metal legs and cross members. Size shall be 2050(L) x 850(D) x 750(H). IGBC, BIFMA and ISO certified. Design: HNI make or equivalent

Providing Siesta double bed made of Prelam particle board body with prelam headrest and footrest attached at both ends. Size 2050(L) x 1650(D) x 750(H). IGBC, BIFMA and ISO certified. Design: HNI make or equivalent

2 Door Wardrobe

Providing metal 2 door storage made of 0.8mm thick CRCA section having size 750 x 450 x 1800mm ht with 3 nos. adjustable shelves. IGBC, BIFMA and ISO certified. Design: HNI make or equivalent

Study Table

Providing KD fitting table with 25mm tabletop supported on 25mm thick gable ends and 18mm thick modesty panel of size 1200mm x 600mm x 750mm ht. All edges to be finished with 2mm thick PVC edgebanding. IGBC, BIFMA and ISO certified. Design: HNI make or equivalent

Supplying fitting and fixing Water purifier of approved make like Aquaguard or equivalent with all required pipe work and electrical work all cost complete as per direction of E/I. all pipe works etc.

Add 12 % GST

Add 1% Labour Cess

ARUN KUMAR