ADDN/ALTN AND SPECIAL REPAIR TO BLDG NO P-3, P-4, P-5, P-8, P-9, P-10, P-18, P-26, D-42 AND P-50 (10 BLOCKS) OF JCOs AND OR MD ACCN AT KABUL LINE UNDER GE (EAST) DELHI CANTT-10

Amount

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed.

Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

Dismantling of PVC water tanks of exc 250 litres and n.exc 500 litres capacity of any condition or type complete all as specified and directed.

Dismantling of Cast Iron pipe up to 100 mm bore complete all as specified and directed.

Taking down steel window and ventilator complete all as specified and directed.

Dismantling of Brick tiles or terracing tiles, single layer on roofs, kerbs, aprons, etc. (each layer) complete all as specified and directed.(Note : All roots of plant on either on wall or roof to be removed and making good the disturbed surfaces. The rate quoted be the contractor is deemed to be included in the unit rates.)

Demolition of Mud phuska in roofs, any thickness including plastering and leeping of any thikness upto 30cm deep complete all as specified and directed.(Note : All roots of plant on either on wall or roof to be removed and making good the disturbed surfaces. The rate quoted be the contractor is deemed to be included in the unit rates including the removal of mud phuska outside defence land.)

Dismantling of floor of WC with Indian type Water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc complete all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite.(d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified.(e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall.(f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) The area of Each WC portion is n.exc 2.00 Sqm each. (h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator.

Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed.

All as per item No. 10 above but 20 mm bore

All as per item No. 10 above but 50 mm bore

Taking down chowkats or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down chowkats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each and refixing in the same or other opening as required at site complete all as specified and directed. Note : The rate quoted by the contractor are inclusive of taking down old mild steel hinges carefully without damaging and refixing in the same or other opening as directed. Nothing extra cost will be allowed in this account.

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish,vegetation etc outside complex (MOD land) complete all as specified and directed.

S&F Fiber Glass Reinforced Plastic (FRP) Door Frames of cross section 90mm x 45mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

S&F 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardantgrade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames complete all as specified and directed.

M&L Frame work as in door chowkhats with angle iron welded together ends of angle shouldered and fixed to opening and welding 3 Nos mild steel butt hingese, and 6 nos hold fasts made out of FI 25x3 mm 30 cm long for fixing of chowkhats( Butt hinges paid separately) complete all as specified and directed.

M & L framed work such as grills, grating etc with ends of bars shouldered or riveted or forged into spikes framed guard bars and similar work confirming to Fe - 290-0 or E-165 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 35mm thick factory made flush shutters solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

M&L Factory made 2nd class hard wood glazed and skeleton shutter 35mm thick, factory made, open rebated and prepared to receive glass/guage etc, without sash bars, mitred and rebated, with edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/guage etc, sizes of members of shutter as specified in section 8, clause 8.24(a) of SSR Part I complete all as specified and directed.

S&F 25 mm thick flush shutter solid core construction with block board core and ply wood face panel commerical type on both side to be fixed as shutter of cupboard/kitchen cup board/loft board including two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 100 mm long (size) butt hinges, stainless steel AISI-304 Grade with brass/bronze hinge pin, complete all as specified and directed.

S&F 75 mm long (size) butt hinges, stainless steel AISI-304 Grade with brass/bronze hinge pin, complete all as specified and directede.

S&F 300mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed.

S&F in repair Stainless steel of AISI-304 grade barrel tower bolt 200 mm long, extruded section complete all as specified and directed.

S&F Stainless steel of AISI 304 grade barrel tower bolt 200 mm long , extruded sections complete all as specified and directed.

S&F Stainless steel handle of size 150mm size long complete all as specified and directed.

S&F in repair Stainless steel of AISI 304 grade floor door stopper with hard drawn steel spring 140mm long complete all as specified and directed.

S&F Stainless steel of AISI 304 grade floor door stopper with hard drawn steel spring 140mm long complete all as specified and directed.

S&F in repair 300mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified.

M&L Cement concrete 1:2:4 type B1(using 20mm graded crushed stone aggregate) as in bed blocks for hold fast, coping, benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces complete all as specified and directed upto four storey height.

S&F Hasp and staple, 75mm size, safety type, brass with mild steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified and directed

S&F in repair 40mm dia, cup boards stainless steel knobs fixed with nuts , screw and washer of mild steel bright finished complte all as specified and directed

S&F 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, complete all as specified and directed.

S&F Continuous piano hinges stainless steel of AISI 304 grade width of flaps (when open) 30mm complete all as specified and directed.

M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparing and removal of old wood surface and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

S&F for steel ventilator (top hung) fabricated rom roll formed sections made of galvanized steel colour coated powder coated (Base steel as per IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM with total c oated thickness of 0.60mm. The coated section shall be with primer coated of primer of -7 microns thick, finish painted with a polyster paint of 12.16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure plyster powder upto 50-60microns thick with the following specifications (a) Main frame 72mm x 55mmx0.58mm (b) Mullion 72mmx50mm x0.58mm(c) Glazed /guazed shutter frame 47mmx20.20mmx0.58mm (d) Glass beads size 12mmx12mmx0.58mm Accessories. Each shutter shall be provided the following fittins (a) Stainless steel pipe of hinges 01 set (b) Alumminium powder coated handle-02 Nos . Glass panes Glazed shutter and fixed glass provided with glass of 5.00mm thick float glass . WIRE MESH –Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperature 1.40mm.. Note: The glazed/Guaged shutter shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof shall be made. Area of shutter shall be the area of opening. The rate quoted by the contractor is deemed to inclusive of all aspects as specified in Drg No CEDZ/TD/289 sheet 1 R/2 and 2R/2.

S&F for steel windows fabricatedfrom roll formed sections made of galvanized steel colour coated powder coated (Base steel as per IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM with total coated thickness of 0.60mm. The coated section shall be with primer coated of primer of -7 microns thick, finish painted with a polyster paint of 12.16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure plyster powder upto 50-60microns thick with the following specifications (a) Main frame 72mm x 55mmx0.58mm (b) Mullion 72mmx50mm x0.58mm(c) Glazed /guazed shutter frame 47mmx20.20mmx0.58mm (d) Glass beads size 12mmx12mmx0.58mm Accessories. Each shutter shall be provided the following fittins (a) Stainless steel pipe of hinges 01 set (b) Alumminium powder coated handle-04 Nos . Glass panes Glazed shutter and fixed glass provided with glass of 5.00mm thick float glass . WIRE MESH –Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperature 1.40mm. Grills window shall be provided with grill made of 10mm square MS bars welded to 12mmx6mm thick MS plate . Distance between bars should not be more than 12cm c/c. Total grill unit shall be enamel painted and fixed to window frame with screw . Note: The glazed/Guaged shutter includingguard bars shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof and guard bars shall be made. Area of shutter shall be the area of opening. The rate quoted by the contractor is deemed to inclusive of all aspects as specified in Drg No CEDZ/TD/289 sheet 1 R/2 and 2R/2.

M&L black Granite of bevelled both edges 18 to 20mm thick with uniform texture (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in cement mortar (1:4) including pointing with white cement (1:2) using marble dust with admixture of pigment to match with marble shade of makrana doogri green colour stone for Kitchen cooking platform laid over and including 15mm thick screed bed in cement mortar (1:6) polishing bevelled edges of corner etc complete all as specified and directed.

All as per serial item no 44 above but on vetical surfaces including 15 mm thick rendering in cement mortar 1:4

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified and directed

M&L for Brick work with sub class B bricks of old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan to any radious in half brick thick wall built in CM 1:4 complete all as specified and directed.

S&F Mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for providing reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in kitchen slab, Chajjas, lintels complete all as specified and directed. Note : The rate quoted by the contractor is deemed to include the necessary scafoldings, supports etc. Nothing extra will be claimed on this account. The work will be executed upto G+3 Stories building.

M&L Kota stone slab single piece with uniform texture 20-22 mm thick in floor with laid over and including 15 mm thick screed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L kota stone slab with uniform texture of 18-20 mm thick in treader of steps, riser of steps, skirting, dado and pillars in one single piece (size decided by Engineer-in-Charge) laid over and including cement screed 15mm thick in cement morter 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , bevelled edge of corner etc complete all as specified and directed.

S&F Form work to sides and soffits of shelves etc including supports such as kitchen shelves, platforms and similar works rough finish surface of concrete (the thickness of slab/shelves n.exc. 100 mm) complete all as specified and directed.

M&L Rendering 10mm thick plastering in cement mortar 1:4 as in ceiling finished even and smooth without using extra cement to match with existing surface complete all as specified and directed.

M&L Rendering 15 mm thick in cement mortar 1:6 otther than fair face of brick work/ concrete surfaces and finished even and smooth without using extra cement complete all as specified.

M&L Rendering 15mm thick plastering in cement mortar 1:4 in walls finished even and smooth without using extra cement to match with existing surface complete all as specified and directed.

Note for Item No 54 to 56 : Sand for plastering shall be 100% coarse sand (baderpur/Stone dust) conforming to the sample approved by GE

M&L Non skid Coloured ceramic rectified tile 300x300x7-8 mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Coloured ceramic rectified tiles 300x450 x 7 to 8mm thick, as in vertical surfaces of wall such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L Coloured ceramic vitrified rectified tiles(Double charge) 600mm x 600mm x10 mm thick , joint free as in floors over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Coloured glazed ceramic vitrified rectified tiles (Double charge) 600 mm x 600 mm x 10 mm thick as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

S&F 15mm bore GI tubing heavy grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.

All as per item No 61 above but 20 mm bore.

All as per item No 61 above but 50 mm bore.

S&F white colour Rotational moulded polyethylene water storage tank 500 litres capacity, ISI marked triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S&F in repair viterous china squatting pan 'ORISSA Pattern' size 580x440mm white with integral foot rests incl P or S Trap) (excluding flushing cistern & flush pipe) complete all as specificed and directed.

S&F vitreous chinaware white colour oval shape wash hand basin (WHB) size 550mm x 400mm Ist quality, including pedastal suitable for wash hand basin complete all as specified and directed.

Supply and fixing in repairs PVC valve less syphonic action type Dual flushing cistern 10 ltr capacity, low level, white with inlet, ball valve, float and handle including brackets and connection to pipes and fixing of chain and pull or lever if any complete all as specified and directed.

S & F Brass CP basin mixer for mixing hot & cold water screwed down for iron pipe 15 mm bore, screwed down high pressure, screwed for iron pipe and fixed complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracked guard and railing 60 cm long complete all as specified and directed.

S&F stainless steel sink AISI 316 grade without drainage board of 1 mm thick kitchen or laboratory with plug , washer and waste, bedding in cement morter to dwarf wall or including CP Waste , PVC Down pipe etc and fixing cantilever brackets and connecting union to pipe overall size495mmx 420mm bowl size 410mm x330mm x160mm etc compete all as specified and directed.

S&F stainless steel kitchen plate rack 1 mm thick four shelves made out of stainless steel sheets 1 mm thick over all size 1.20x90x25cm complete all as specificed and directed.

S&F Chromium plated tubular towel rail, 20mm dia, ‘D’ type 60cm long between flanges of brass chromium plated and fixed with brass screws complete all as specified and directed .

S&F stainless steel peg set of six complete all as specified and directed fixed in repair.

S&F in repairs 15 mm bore Angle valve cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed .

S&F wall mixture with bend pipe for over head shower on upper side of 15 mm bore cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs 15mm bore bib taps long body,fancy type(water saving bib tape )Standard of Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed.

S&F in repairs CP brass shower rose size 2000mmx200mm(square size) with chromium plated arm fixed to 15mm pipe of revolving type complete all as specified and directed.

S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron iron complete all as specified and directed.

S&F 15 mm dia Ball brass valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic bell screwed for iron pipe and fixed complete all as specified and directed.

M&L Preparation of new or previously untreated steel surfaces of any description over 10cm in width or girth,not otherwise specifically and applying two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified and directed

S & F 100mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified and directed

All as per item 82 above but except pipes

S & F 75 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified and directed

All as per item 84 above but except pipes

S & F 50 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified and directed

S&F in repair 100mm dia (bore of pipe) cast iron Tee diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified and directed

All as per item 87 but 75mm dia (bore of pipe) Tee

S & F 75mm dia (bore of pipe) branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified and directed

All as per item 89 above but 100mm dia (bore of pipe).

S&F in repair cast iron floor trap square type with Cockroch Proofing CP grating with or without hole including provision of jointing to waste pipes in run lead joint of size 100 mmx100mm (Square shape), complete all as specified and directed.

S&F in repair 100 mm pipe, stack clamps out of 50mmx 5 mm flat iron and 16 mm dia round iron stamp including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

All as per item No 92 above but 75 mm bore pipe.

Cutting holes in brick wall built in CM for inserting hold fast and exc half brick but n exc one brick making good dismantled portionin CM (1:3) or cement concrete (1:2:4) type BO as required complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

S&F Drappery curtain rods decorative type stainless steel 25mm nominal dia of approved quality (3mm wall thickness) including fixing of two number decorative brackets fixed in brick/concrete wall, Two number of latto on both ends of curtain rods ( The length of each curtain rod will be 1.00m to 1.50m long) complete all as specified and directed

M&L for providing pre cast cement concrete jallies, 50mm thick type BO, 1:2:4 (12.mm graded stone agg) set in cment mortar 1:4 incl all moulding complete all as specified and directed

M&L for applying a coat of bituminous primer conforming to IS - 3384 @ 0.50 Litres/qm on prepared surfaces of plaster and applying APP based polymeric membrane with mineral slate finish @ 4.00 Kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric and sealing joints by torch application complete all as specified and directed.

M&L Screed bedding 20mm thick plaster in CM 1:4 on roof finished even and fair using integral water proofing admixtuire.(Note : Supply only water proofing admixture shall be measured and paid separately) complete all as specified and directed .

M&L 75mm thick PCC 1:3:6 type C2 using 40mm graded crushed stone aggregates as in plinth protection finished even and fair complete all as specified and directed.

M&L for mild steel work in bands, straps, holdfast, hookand pintle hinges confirming to Fe-10-0or Fe-310-0 complete all as specified and directed.

M&L Resecuring or Easing and adjusting , without taking down shutters of doors/windows for easy opening /closing ,tightening of hinges and changing its position or adjustment of tower bolts/sliding bolts etc area not exc 2 sqm each complete all as specified and directed.

M&L Cement concrete 1:2:4 type B0(using 12.5mm graded crushed stone agg) as in roof levelling complete all as specified and directed

M&L Cement concrete type B1-1:2:4 (using 20 mm graded crushed stone agg) in roof kerbs or mud stop rounded or chamfered on edge etc complete all as specified and directed.

M & L 150mm dia Intercepting traps of salt-glazed stoneware, with square ends to inspection arms for building flush into manholes and setting in cement mortar 1:1 complete, including concrete foundation of width and thickness as for pipes of same dia and haunching after setting. Cleaning arm to include a glazed ware stopper, galvanised iron bayonet joint (or other approved pattern) and galvanised iron lever (or trigger), galvanised iron chain, hook and ring

M&L for preparation of old decorated external wall surface by complete removal of existing treatement by mechanised sander of Berger paints or equioovalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechincal removeal is not possible and applying a layer of 2 mm thick wall care putty, again sand papering thus making surface smooth and applying two coat of wheather proofing exterior acrylic emulsion paint Premium quality over a coat of alkali resistant primer on old/new wall surfaces complete all as specified. Note : Material shall be procured from manufacturer and work shall be got executed through authorised applicator. Only for MoU & Guarantee refer Sch ‘A’ Notes and PS for Ser No A to F.

M&L for CP towel ring fixed with and including CP brass screws and wooden/plastic cleats. complete all as specified and directed

Fabrication & fixing of kitchen cabinet & wardrob/cupboard made out of 15 to 18 mm thick PVC board plain sheet including providing cabinet for keeping/basket/cutlery basketwith handles complete all as specified and directed.

Fabrication & fixing of kitchen cabinet & wardrob/cupboard made out of 15 to 18 mm thick PVC board laminatd sheet including providing cabinet for keeping/basket/cutlery basketwith handles complete all as specified and directed.

M&L for PVC sheet white 6mm thick fixed with approved adhesive and stainless steel machine screw (star) in narrow widths of nexc 10 cm width complete all as specified and directed.

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M & L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor s complete all as specified and directed.

S&F steel work in tubular trusses of Fe 410-W(Gde-E-250) quality A including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St-240

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified

S&F 4-5 mm thick SS wire for hanging of clothes including all fitting and fixture complete all as specified and directed..

Propping and supporting the structural members and its adjoining areas with steel props (adjustable or as required), bracings, steel/timber runners etc to relieve the structural member of the required load coming over it as per the pattern given by the contractor & approved by Engineer-in-charge complete all as specified and directed.

Providing and fixing special water tight centering and shuttering including bolting, strutting, propping etc so as to withstand a pressure of 0.1 Mpa including removal of forms for all locations including beams, columns, slabs, walls, foundations, footings, landings, stairs, balconies etc.

Providing and fixing temporary engineered steel tubular standard double scaffolding system on the exterior side, maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc with suitable working platforms at required locations with essential safety features for the workmen etc complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose complete all as specified and directed..

Providing and fixing plywood covering panels as per the directions of Engineer-in-Charge with necessary backing framework to shield windows etc. from falling debris and removing and taking away the material after completion of work including making good any incidental damage (s) to the existing building or its finishes etc complete. (The measurements for payment shall be made in terms of the area protected by such covering).

Providing, erecting, maintaining and removing temporary protective screens made out of woven PVC cloth with all necessary fixing arrangement to ensure that it remains in position for the work duration as required complete all as specified and directed.

SURFACE PREPARATION

Chipping of unsound/weak concrete material from slabs, columns etc. with standard power driven percussion type or pneumatic chisel of standard make as directed by Engineer-in-charge including tapering all edges, making square shoulders of cavities etc complete and disposal of debris up for all lifts and leads

(a) 25 mm average thickness.

(b) 50 mm average thickness

Dismantling & removing existing treatment over RCC slabs at all heights including stacking of serviceable material for reuse as per direction of Engineer-in-charge & disposal of balance unserviceable material within a lead of 50 metre complete all as specified and directed.

Dismantling existing RCC work but excluding cutting of reinforcement bars at all heights including disposal of unserviceable material within a lead of 50 metre Manually using chisel and hammer or Mechanically using power driven/pneumatic percussion type chisel/ hammers complete all as specified and directed.

Cutting reinforcement bars in RCC or reinforced brickwork, carefully without damaging the existing structure and its finished from Bars of dia 8 mm-20mm

Cleaning of reinforcement from rust including behind the reinforcing bars to give it a totally rust free finished steel surface by hammering the rebar, using wirebrushes, chiseling and using alkaline rust remover of approved make with paint brush and removing loose particles after 24 hrs of its application with wire brush and thoroughly washing with water and allowing it to dry all complete all as specified and directed.

(a) Bars up to and including 12mm diameter.

(b) Bars above 12mm diameter.

Introducing new reinforcement bars for structural connections in RCC beams, lintels, columns and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 100mm and upto 200mm, fixing the reinforcement in position using epoxy. (Rate shall include cost of labour, T&P for power drilling in concrete, epoxy cartridges, plastic nozzle etc complete including cleaning the drilled holes of loose dust by blowing air. The cost of reinforcement shall be payable separately.

(a) Bars up to and including 12mm diameter.

(b) Bars above 12mm diameter.

Providing and inserting 10 mm dia 200 mm long mild steel shear key bars of required length and diameter in reinforced/ plain concrete as per drawing and directions of Engineer-in-Charge including power drilling holes of appropriate diameters to a minimum depth of equal to 12 items the diameter of shear key bar/levelling gauge, cleaning the drilled holes of loose dust by blowing, insertion of epoxy from cartridge, placing the shear key bar in position and allowing it to stay undisturbed for 24 hours. (Rate shall include cost of labour, all materials, T&P for power drilling in concrete, epoxy cartridges, plastic nozzle etc complete including cleaning the drilled holes of loose dust by blowing air.

Cleaning with wire brush, chisel etc for all height exposed concrete surface of lightly sticking materials including foreign materials, loose concrete/ aggregates, etc. The rates shall include cost of movable scaffolding & working platform (cost of working platform shall not be paid under other item) disposing of all debris up to lead of 50 metres and complete in all respects.

CRACK/HONEYCOMB AREA REPAIR

Providing and inserting 12mm dia Aluminium / galvanized iron injection nipples along crack lines or honey-comb area, including:- (i) Drilling holes of required diameter up to depth from 40mm to 80mm or half the thickness of member (whichever is less), at required spacing of 30 mm. (ii) Making grooves of size 12mm x 12mm along the crack line. (iii) Making the crack dust free by blowing compressed air and then washing with water. (iv). Sealing the distance between the injection nipples with approved putty (Polymer modified cement mortar/ polyester putty/ epoxy putty) etc and allow it to cure. (v) If cementitious grout material proposed to be used, washing and saturating the cracked surface with water by pumping from top most nipple and downwards complete as per the direction of Engineer-in-Charge. (The rate shall include all material, labour and all operations above. The cost of grout material shall be paid separately on the basis of actual quantity consumed.

Supply and injecting approved grout in appropriate proportion excluding cost of such grout material covered under Ser No 20 into cracks/ honey-comb area of concrete/ masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete all as specified and directed.. (The payment shall be made on the basis of actual weight of approved grout injected).

(a) Epoxy grout in Concrete/ RCC work.

(b) Stirrer mixed SBR Polymer modified cement slurry made with shrinkage compensating cement in Masonry Work.

BONDING COATS

Supply, mixing and applying bonding coat, including cost of material, on prepared non-metallic surface of parent material as per specifications and directions of Engineer-in-charge complete, SBR polymer @10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area with its proportion complete all as specified and directed.

Supply & Applying alkaline passivating & bonding coat of approved adhesive over reinforcement duly approved by Enginner-in-charge with approved epoxy bonding coat as per manufacturer’s specifications including sprinkling silica sand (Nos 10) for:

(a) Bars upto 12 mm diameter.

(b) Bars above 12 mm diameter.

STRUCTURAL REPAIR ITEMS

Providing and placing in position Grade M25 Micro-concrete, which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion obtained from approved manufacturer as per specification and directions of Engineer-in-charge (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/ tapping with a blunt metal instrument

Reinforced Concrete: Providing and laying in position M25 grade of reinforced concrete in beams, slabs, columns upto a floor 5 level excluding the cost of centering, shuttering, formwork.

Reinforcement for R.C.C work including Cutting, bending, binding, straightening and placing in position &/or welding with the existing bars wherever necessary complete.

Providing, mixing and applying Polymer Modified Mortar in layers, each layer not execeeding 10mm thick, including trowelling with wooden tools etc. complete as per specifications and directions of Engineer-in-charge For payment purposes, pre-measurment of thickness shall be done just after the surface preparation is completed. (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) Cement (75mm size cube crushing strength at the end of 28-daynot to be not less than 25 N/sqmm)

(a) 25 mm average thickness (in 2 layers).

(b) 50 mm average thickness (in 3 layers).

Cleaning the concrete surface of by sand blasting with coarse sand followed by and including cleaning with oil free air blast complete all as specified and directed.

Providing and fixing reinfoorcement with hard drawn steel wire fabric of 3 mm dia wire,100 mm pitching fixed to existing RCC slab (bottom face)

Shotcreting (Guniting) RCC slab 20 mm thick with approved mix mortar (with ordinary portland cement ,coarse sand in propertion (1:3) including the cost of centering and shuttering at edges and corner if required,wet curing etc.complete all as specified and directed. Surface shall be satisfactory evaluated by sounding /tapping with a blue metal instrument.

M&L for complete removal of old paint on old steel surface of any description over 10cm in width or girth , not otherwise specifically for applying D CHLORO METHANE CHEMICAL and applying two coats of synthetic enamel paint ovar a coatof red oxide primercomplete complete all as specified and directed.

Removing existing paint by scrapping with Trucare wall sander : L-01/H-01 (having mechanical vacume mechanism) having RPM not less than 1500, sanding pad of 80 grit having dia of 7”/9” to make the surface free from dust, loose paint etc by skilled labour, complete all as spd and directed.

Providing 2mm thick wall care putty and applying one coat of acylic water based interior grade primer @0.8 ltr (undiluted)/10 Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application of asian paints Trucare Graco or equivalent having an electric motor of min HH with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI allow 6-8 hrs to dry the surface for painting of subsequent coats, complete all as spd and directed. Note : Material shall be procured from manufacturer and work shall be got executed through authorised applicator. Only for MoU & Guarantee refer Sch ‘A’ Notes and PS for Ser No A to F.

Providing two coats of Oil bound distemper on wall/ceiling on old/new surfaces with rich matt finish having BOC less than 50 gms per litre complyikng leed criteria @ 1 Ltr (undiluted/10Sqm) diluted in the ration 2:1, applied over priming coat with fully automatic airless spray machine of paint application of Asian paint Trucare Graco or equivalent having and electric motor of min 1 HP with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI allow 6-8 hrs to dry the surface for painting of subsequent coats, complete all as spd and directed.Note : Material shall be procured from manufacturer and work shall be got executed through authorised applicator. Only for MoU & Guarantee refer Sch ‘A’ Notes and PS for Ser No A to F.

S&F Stainless steel Armoured Connection size 15mm bore and 45cm long with washer complete all as specified and directed.

M&L for heat resistance tiles sizes 300x300x20mm for roof and joints grouted flush and pointing in cement mortar 1:3 over 20mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for UPVC 50 mm dia pipe fixed complete to walls, ceiling or in floors etc.. complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in CM 1:3 to ends or edges of landing steps, cills sunshades, shelves, lintels and cutting chasing for concealed water tubing and making good, cutting not exc 10cm girth complete all as specified and directed.

M&L for brass bottle trap of size 32 mm dia of discharge pipe for WHB complete all as spd and directed

M&L for door seal 25mm wide for prevent of insect complete all as specified and directed.

M&L for brass magnetic catcher for kitchen cabinet complete all as specified and directed.

M&L two coats of Black bituminous paint one GI tubbing (New/old) surfaces of any description not exceeding 10 cm width or girth complete all as spd and directed

M&L non skid clolorued ceremic tiles 600mmx600mmx10mm thick as in floor over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Description of Work / Item(s)

Amount

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

M/L 75 mm thick Plain cement concrete (1:4:8) Type D-2 using 12.5mm graded stone aggregate as in floors and finished the surface fair to received screed bed all as specified and directed. even and smooth without using extra cement

Sand filling under floors or in foundations including watering and consolidations complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 80mm thickness M-40 Grade with grey cement and pigment complete all as specified and directed.

Description of Work / Item(s)

Amount

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed.

Returning filling in, including spreading levelling watering and well ramming in layers n exc 25cm thick (after the pipes have been laid and tested) in soft/loose soil complete all as specified and directed

Removing excavated material (soil) not exceeding 50M and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

M&L for cement concrete 1:4:8 type D2 (using 40mm graded agg)incl packing under and haunching against the sides for 163mm internal dia DWCPE (SNP) pipes after they are laid and tested complete all as specified and directed. (thickness of concrete bed 150mm).

Supply and laying, DWCPE (SNP) pipes of 163mm internal dia and 180mm external dia incl testing and laid in trenches to a level on concrete bed complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L Brick work using sub class’B’ bricks in CM ( 1:4) straight or curved on plan exc 6 mtr mean radiuscomplete all as specified and directed.

M&L for rendering 12mm thick in CM 1: 4 on fair faces of brick work or concrete surfaces with water proofing compound finished even and smooth without using extra cement complete all as specified and directed.(Water proofing compound shall be measure and paid separatelly)

Supply only liquid water proofing compound ,

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150/200mm dia pipes complete all as specified and directed.

S&F Precast plastic fibre reinforced concrete man hole covers" medium duty " of overall size 1000 mm x 500 mm x 75 to 80 mm factary made complete all as specified and directed .

M&L for providing PCC 1:2:4 type B2 in surface channels and drains (using 20 mm graded crushed stone aggregate ) complete all as specified & directed.

M&L Cement concrete 1:2:4 type B1(using 20mm graded crushed stone aggregate) as in bed blocks for hold fast, coping, benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces complete all as specified and directed upto two storey height.

Description of Work / Item(s)

Amount

Taking down old unserviceable point wiring from existing conduit / batten type (light, fan, socket or power point) complete such as switches, ceiling rose, pendent holder, regulator and socket etc and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing complete all as specified and directed.

M & L Point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated un-sheathed and stranded copper conductor cable ISI marked in and including PVC concealed conduit ISI marked of suitable size but not less than 20 mm dia and 1.5 mm wall thickness and PVC conduit fittings such as tees, bends, elbow, reducers and conduit junction box (junction box will be of MS) including FRLS PVC insulated unsheathed 1.5 Sqmm single core copper as earth wire, connecting to common earth dolly with thimble, including pressed steel powder coated MS sunken box of suitable size, covered with & including 3 mm thick bakelite, laminated hylem sheet top cover and making good surface as original by plastering and whitewash/colour/distemper etc complete all as specified (cost of MS sunken box and bakelite sheet is included in the rate) for the following.

(a) One light/ fan/bell point controlled by one by one way switch ( switch to be measured and paid separtely)

(b) one socket outet point 5 amps on the same board.

(c) one socket outet point 5 amps on the independent board.

(d) one light point controlled by two Nos of two way switches.

M & L in replacement for point wiring complete with 2.5 sq mm (nominal area) FRLS PVC insulated, unsheathed and stranded copper conductor cable ISI marked, in and including PVC concealed conduit of size 15 mm dia and 1.5 sqmm wall thickness and conduit fitting such as tees, bends, elbow, reducers except conduit junction box (junction box will be of MS) for one 15 Amp/ Geyser /AC including FRLS PVC insulated 2.5 sq mm copper earth wire, connected to common earth dolly with thimble and including pressed steel powder coated MS sunken box of suitable size covered with and including 3 mm thick bakelite laminated hylem sheet top cover etc complete all as specified (cost of MS sunken box and bakelite sheet is included in the rate). Note : Point wiring for above item will not be mixed with light/fan point circuit or not in the same conduit pipe.

M & L sub main wiring with 2 run of 6 Sqmm (nominal area) FRLS PVC insulated, unsheathed and stranded copper conductor cable ISI marked drawn in to PVC conduit with and including independent 6 Sqmm (nominal area) FRLS PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire connected with thimble from main DB to sub main DB complete all as specified (conduit, conduit accessories and cost of earth wire is included in sub main wiring).

S & F of Switch piano flush type single pole one way ,5/6 Amps.

S & F of Switch piano flush type single pole two way ,5/6 Amps.

S & F mega Bell push of socket size with neon lamp, 5/6 Amps, 240 volts SP.

S & F in replacement of socket two-in-one 2/3 pin, 5/6 Amp universal type.

S & F of Socket 16 Amp multipurpose shutter type.

S & F of Switch 16 Amp single pole one way type.

S & F of Phase indicator switch type 6 amp.

S & F of Ceiling rose, surface bakelite 3 terminal, 240 volts, 5 Amps with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size & MS box of suitable size complete ,all as specified and directed.

S & F of lamp holder insulated body with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size & MS box of suitable size with and including LED 9W etc complete all as specified and directed.

S&F of bell DINGDONG type, 6 Amps, 240 volts, SP all as specified and directed. .

S & F of fan regulator electronic step type switch size and making all necessary connections complete all as specified and directed.

S & F of MCCB Incomer distribution board double door vertical type made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating surface mounting VTPN 4 way, 415 volts with copper bus bar rating 250 Amps, dust and vermin proof suitable for incorporation of MCCB and IP 54 - IK 09 protection with and incorporation of MCCB upto160 amp complete all as specified and directed. (Note : cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quoted rate).

S & F of MCB C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA of capacity 10 to 32 Amps complete all as specified and directed.

S & F of MCB C Curve type suitable for 240 volts AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA of capacity 40 to 63 Amps complete all as specified and directed.

S & F of MCCB 3 pole 415 volt fixed type of capacity 125 Amps with braking capacity 16 KA complete all as specified and directed. .

S & F of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and directed. (Note : cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quoted rate)

Supply and fixing metal body heavy duty exhaust fan 300 mm sweep 230 volt AC with & including louvers and all fixing arrangements including making hole in the wall of suitable size for fixing ventilating fan, plastering and making the surface good as original, complete all as specified & directed.

Supply and fixing of LED tube light fitting, diffuesed type suitable for 22 W LED tube light with extruded aluminium heat sink for efficient heat dissipation alongwith integrated HF electronic driver complete all as specified and directed.

S & F of bulk head light fitting as per sketch no 11 of plate no 6. including LED lamp 7 W and making all electric connections complete all as specified and directed.

Supply and fixing of LED tube light fitting, diffused type suitable for 10 W , 2 feet length to use as mirror light LED tube light with extruded aluminium heat sink for efficient heat dissipation alongwith integrated HF electronic driver complete.

S & F of street light bracket incl clamp, nut and anchor bolt etc make to shape for street light fitting made out of GI pipe light grade 25 mm bore 1.5 mtr long on the top of wall of existing building complete all as specified and directed.

S & F in of energy efficicent LED fittings 40 W LED 6K suitable for street/builing area light pressure diecast aluminium roadway luminaire with high power LEDs and HF electronic driver ccomplete all as specified and directed.

M & L of Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6.3 mm thick burried in ground vertically to a depth not less than 2.25 meters below ground level with top edge of the earth plate at a depth not lesss than 1.5 meter below the ground level, earth plate surrounded 15 cm thick layers of common salt and charcoal dust starting from ground below 15 cm of earth plate and up to 15 cm above the same. GI plate connected with galvanised iron earth lead of size 4 mm by means of galvnised nuts, bolts and washers. GI wire of 4 mm dia laid in 15 mm dia light grade GI pipe as protection from top of the plate up to test point (cost of protection pipe up to 7.5 meters from earth electrode will be included in the rates quoted by the contractor) with following:- (a) test point of GI.

(b) Watering pipe GI light grade 20mm dia from top of the earth electrode up to MS funnel with brass wire mesh embeded in floor of PCC earth pit. (GI watering pipe should properly tightned on GI plate & Funnel and embeded in PCC floor of earth pit)

(c) PCC earth pit 30cmx30cmx30cm constructed in PCC 1:2:4 type B1 exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC pit cover 25mm thick with 1 Nos MS handles suitable for carrying of pit cover.

(d) Angle Iron Frame Made of 40x40x4 mm size angle iron for holding earth pit cover.

S&F water storage heater 5 star in white colour with metal body (Geyser) of capacity 25 ltr, vertical type, AC, electric, 230 volt, complete with heating element, thermostat, 3 core lead, Plug top, safty valve, inluding electric and water connection using MS Iron suitable nut, bolts & washers and making good to disturbed surface complete all as specified and directed.

S & F of fresh air fan 200 mm sweep size incl all fixing accessories,making hole in wall and electric connections incl taking down issue as per dircted to Engr-in-Charge complete all as specified and directed.

S&F BLDC (Brushless Direct Current) Ceiling Fan, 1200 mm suitable for regulator, not less than 350 RPM, not less than Air delivery 215 cum/minute, voltage 220V, high air follow with silence operation, having full copper motor winding & ribbed 3 Nos A/M blades. The BLDC motor fan shall have 100% rust-free blade. The fan shall have BEE 5 star rating and compliant with IS-374 and making necessary electric connection of suitable PVC copper wire from ceiling rose to ceiling fan including taking down existing ceiling fan and depositing the same in the storeyard of AGE E/M or GE (East) complete all as specified and directed.

S & F of Sheet metal enclosure with a two pin top plug and socket incl one SP MCB 20 Amp complete all as specified and directed.

Material and labour for laying of LT underground cable XLPE insulated, PVC sheathed, galvanised steel strip / wire armoured, aluminium conductor, 1100 volts grade, of size 50 Sqmm 3.5 core suitable for earthed system laid in duct / trench / along pole / wall etc including making connection complete all as directed. Make:- Finolex/Grandly/Havells.Note : 1. The cost of Al thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it.2. The excavation, earth work, sand cushioning and brick protection etc will be measured and paid separately under respective items.

Excavation in trenches in loose/soft soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep and getting out including forming bottom surface for laying LT cable as specified and directed.

M&L for sand cushioning to under ground cable provided with layers of snad(8 cms deep before laying the cable and 15 cms deep after laying) complete all as specified and directed.

Supply and laying burnt bricks class - B for protection of cable complete all as specified and directed.

Returning filling in soil including spreading, levelling, watering and well rammingin layers not exceeding 25 cm complete as specified and directed.

Removing exccavated soil not exceeding 50 mtr and depositing wheredirected at a level not exceeding 1.5 mtr above the starting point complete as specified and directed.

M & L in replacement for laying of Galvanised Iron tubes light grade 80 mm dia for cable protection at site complete all as specified and directed.

Rough excavation in trenches in hard rock/ road not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for shafts, wells, cesspits, manholes, pier holes and getting out including forming bottom surface for laying LT cable as specified and directed.

imran construction company

ASSOCIATED CONSTRUCTION CO.

M/s Puja Construction Company

AMIT ASSOCIATES

tarun construction co

imran construction company

M/S Chhavi Constructions Co

AMIT ASSOCIATES

M/s Puja Construction Company

tarun construction co

AMIT ASSOCIATES

imran construction company

tarun construction co

ASSOCIATED CONSTRUCTION CO.

M/s Puja Construction Company

imran construction company

AMIT ASSOCIATES

tarun construction co

M/S Chhavi Constructions Co

M/s Puja Construction Company