SMART ROOF TREATMENT, SUNKEN REPAIR AND CERTAIN B/R WORKS UNDER AGE B/R-II AT GE JHANSI

Amount

Removing existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down cement concrete, existing plaster lime cova 80 to 100mm thick mud phuska/cement concrete/lime cova etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush complete all as specified and directed.

M&L of water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane centre core 100mm micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3kg/Sqm as per manufacturer’s instructions with torch applicationcomplete all as specified and directed with following course of description below:- (a) 10 mm thick plaster in CM 1:4 with WPC will be applied over the roof slab when concrete is green. After the plaster is cured the roof will be tested for water tightness by ponding with water for seven days for any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5kg/sqcm using cement based cement grout. After the surface is repaireds the slab will be tested for water tightness again before proceeding with further treatment. (b) the surface of roof, parapet and gutters, drain mouths, etc. over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as, fungus, moss, dust etc by wire brushing and dusting. For cast iron drain out lets a grove shall be cut around to tuck in the treatment. Concrete angle-fillets shall be provided at junctions between roofs and vertical faces of walls (parapet and other walls) around obstacles such as pipes, chimney stacks, etc. and other similar situation to ease up about corners. (c) Bitumious based primer confiorming to IS: 3384 @ 0.3 kg/SM to be applied on prepared surface, till the surface is property. impregnated. (d) After the application of approved bituminous primer the water proofing membrane shall be laid on the primed surface by torch application method as per manufacturer's instruction. The overlap while toching shall be 100mm in longitudinal direction and 100 mm in transverse direction. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer and seling it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (e) All joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane.

M&L for Apply a coat of bituminous aluminium paint @ 0.20 Kg/Sqm over APP membrance, complete all as specified and directed.

M&L for Cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in padding levelling etc and roof kerbs complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) mixed with water proofing compound @ 0.20 Ltr/bags on roof surface when concrete is green, complete all as specified and directed.

M&L for water proofing treatment for roof by applying priming coat of epoxy primer with resin and hardner in 1:3 ratio with water dilution as per manufacturer instructions, applying 2 coats of solvent based Polyurethane liquid applied membrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 kg/sqm (each coat), 2nd coat should be applied once 1st coat becomes dry completely all as specified and directed. Note:(a) The work under this item shall be carried out by the authorized applicator of Manufacturer by using modern techniques. The contractor shall also furnish warranty of quality, finish work and effectiveness of waterproofing treatment under this item for a periof of 10 years from the date of completion along with manufacturer warranty of material for the same period. (b) Height of bldg is more than 10 meters and roof have continous series of trapizium with no staircase to reach at the top of the building. (c) The contractor shall upload MOU letter with any one of manufacturer and also with their authorised applicator mentioned in the tender alongwith their bid in cover-I failing which his bid will be rejected. Authorised applicator shall have valid authorisation letter from the manufacturer (Minimum regional HQs) and shall have been issued not less than 30 days from the date of commencement of the work. The authorisation letter needs to be valid for the complete period of execution work. (d) After preparation of the surface, Engr-in-Charge shall approve the same before applying finishing coats. (e) Building wise stage passing register shall be maintained and shall be signed by Engr-in-Charge and contractor. (f) The equipments to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. (g) Contractor shall submit approved company generated 10 years warranty card at the time of submission of RAR & Final Bill.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc. and hoisting, reconnecting and re-fixing in position of exc. 250 litres & not exc. 500 litres capacity of tanks,Date of cleaning of tank will be marked on the tank by stencil with synthetic enamaled paint in uniform size, Size of letters & numbers should be 40mm. complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc. and hoisting, reconnecting and re-fixing in position of 1000 litres capacity of tanks, Date of cleaning of tank will be marked on the tank by stencil with synthetic enamaled paint in uniform size, Size of letters & numbers should be 40mm. complete all as specified and directed.

S&F in replacement of 20 mm dia of Brass Ball valves high with flynut complete screwed for iron pipe or brass ferrel complete all as specified and directed.

Demolition of cement concrete of any description and in any position of WC’s/Bathroom etc in sunken portion area above ground floor, removing demolished material completely and old waste pipe from sunken portion and cleaning the side/bottom surface of sunken floor with wire brush, complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in padding levelling etc and roof kerbs with liquid water proofing solution finished even and fair with proper slope as prepatory works to water proofing treatment complete all as specified and directed. Note:-liquid water proofing solution shall be provided in 150ml in 50 Kg of Cement by weight and cost of liquid water proofing solutionmeasured and paid seperate item complete all as directed.

M&L for 15 mm thick rendering in CM (1:4) mixed with water proofing compound @ 0.20 Ltr/bags on roof surface when concrete is green, complete all as specified and directed.

Applying a coat of neat cement slurry with 1.20 kg of cement per sq. metre in horizontal and vertical surface. Test of water tightness by ponding for 48 hours & rectify defects if any till total elimination of defects, complete all as specified and directed.

M&L PCC 1:5:10 Type E2 using 40mm graded stone aggregate as in mass filling in two layer in sunken portion complete all as specified and directed.

M&L 50mm dia G.I pipe as in spout to drain out if any leakage occures in the sunken portion complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain and plug and porcelain stopper but including brackets, CP waste copling, 32 mm PVC Waste pipe 600mm long complete all as specified and directed.

Supply & Fix in repairs Vitreous China Squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests complete all as specified and directed.

Supply & Fix in repairs Vitreous China wash down water closet pan (pedestal pattern), EWC, coloured including jet system & matching coloured seat covered fixed complete all as specified and directed.

Supply and Fix in repairs 10 Litres, PVC, valve less, syphonic action type, Flushing Cistern, low level, white inlet, ball valve, float, chain and pull, and brackets including PTMT PVC connection 600mm long and PVC 32 mm dia flush pipe complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves all as specified and directed

S & F 20 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves all as specified and directed.

S&F in replacement of towel rail 600 mm long and wall bracket made of cast copper alloy, chromium plated, complete all as specified and directed.

M & L for Non- skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F for 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F for 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F for 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement, complete all as specified and directed.

M&L for brick work with fly ash lime bricks (FALB) conforming to IS 12894, old size brick, straight or curved on plan exc 6m mean radius built in cm (1:6), complete all as specified and directed.

M&L for half brick thick wall with fly ash lime bricks (FALB) conforming to IS 12894, old size brick, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:4, complete all as specified and directed.

M&L for 15mm rendering thick in CM (1:4) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement), complete all as specified and directed.

M&L for rendering 15mm thick in CM(1:6) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement), complete all as specified and directed.

Preparing newly plastered surfaces of wall and applying two coats of oil bound distember over a coat of putty to make the surface to be plain and smooth complete all as sppecified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat of cement based paint over and including a coat of cement based primer, complete all as specified and directed.

Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for Non skid ceramic colored tiles of size 400x400mm, 7 to 8 mm thick (square / rectangular) as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

M&L for ceramic colour tiles in vertical surface of size 450 X 300 x 7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and directed.

M&L 20 mm thick granite slab, tabled rubbed, machine cut, duly grinding, polishing, moulding etc of all outer edges / sharp corners, duly fixed in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4), incl pointing in grey cement (1:2) using marble dust with admixture of pigment to match with the shade of slab, complete all specified and directed.

M&L for factory made PU coated, chequered cement concrete tiles of any colour 30 cm x 30cm x 20 to 22 mm thick, set & jointed and pointed in neat cement slurry mixed with grey cement and pigments, laid over and including 15mm thick screed bed or bedding layer in CM 1:6, complete all specified and directed.

Demolition of brick work built in cement mortar or lime mortar including all quoins arches, pillars etc complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

Taking down cement plaster on brick or stone wall including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick rendering in CM (1:4) on fair/other than fair faces of brick work finished even and fair complete all as specified and directed.

M&L for 15 mm thick rendering in CM (1:6) on fair/other than fair faces of brick work finished even and fair complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coat of cement based paint over and incl one coat of exterior grade cement based primer, complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coats of oil bound distemper, over and incl a layer of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

M&L for preparation of new plastered surface and applying three coats of white wash on new plastered wall surface, complete all as specified and as directed.

M&L for writing or repainting letters or figures (Block, Roman, Italic, Indian) exc 15.0 cm but not exc 30 cm in height and line of letters or figures not exc 2.0 cm wide for Bldg No / Name and similar works etc with two coat of synthetic enamel paint, complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all specified and directed.

All as per Ser item No 55 above but not exc 1.5 sqm each complete all as specified and directed.

Taking down shutters of any description not exc 01 Sqm each, complete all as specified and directed.

Taking down shutters of any description exceeding 01 Sqm and not exc 02 Sqm each, complete all as specified and directed.

S&F of Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood coloured PVC sheet and edges, reinforced with MS square tube, as specified in SSR Part-II 2010 (Section 8, on Page no - 175), complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frames shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strips of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/or sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F of 100 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21 anodized complete all specified and directed

S&F of 200mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed.

S&F of 140 mm door stopper of aluminium body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed.

M&L for stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed.

M&L for stainless steel rod 15mm dia steel pipe cutting into length as required at site with and incl SS end brackets, fixed in cupboard and similar works, complete all as specified and directed.

M&L for box type steel window with 80x40x1.25 m MS tubular frame with side hung shutters (double shutter for glass and gauze) without sash bars jointed together with and incl grill using 12 mm square bar @ 10 cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars doweled and welded complete all as specified & directed. Note:- (a) The Glass / gauze shell be measured and paid separately. (b) Side hung Z-Section shutter shall be of size 20mm x 20mm x 25mm and 0.3mm thick.

S&F of 35mm thick factory made modular designer flush doors, solid core construction, with block board core and prelamination on both sides, complete all as specified and directed.

M&L for second class hard wood. Plain, solid, straight chowkhats and frame, wrought framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixing, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, copings, bond stones, bed plates for hold fast and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for mild steel angles, bars, flats etc, as in hold fasts, pipe clamps, plain angle cleats for securing purlins, supports for stiffening of fencing, wall ties and similar small articles confirming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for mild steel section as in door/windows chowkhats frame of steel gate of grade Fe-290 Gde E-165 including all necessary machine wks i.e. cutting, welding, grinding etc, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

S&F of 3 mm thick sheet figured glass pin headed type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, complete all as specified and directed.

S&F of 3 mm thick sheet glass ordinary quality and glazing type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, complete all as specified and directed.

S&F in replacement of stainless steel wire cloth 0.36 mm in nominal dia of wire average width of aperture 1.40 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.

S&F of stainless steel wire cloth 0.36 mm in nominal dia of wire average width of aperture 1.40 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.

Taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern, complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.

Taking down steel tubing with and incl connections, of 15 mm dia bore, complete all specified and directed.

Taking down steel tubing with and incl connections, of 20 mm dia bore, complete all specified and directed.

M&L for medium grade galvanised steel water tubing with and incl all fittings and fixtures, fixed to wall or laid in floors for 15 mm bore, concealed or exposed, complete all as specified and directed.

M&L for medium grade galvanised steel water tubing with and incl all fittings and fixtures, fixed to wall or laid in floors for 20 mm bore, concealed or exposed, complete all as specified and directed.

M&L for cutting chases, pinning in for concealed water tubing, not exc 10 cm girth and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F in replacement of 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F in replacement of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as specified and directed.

S&F in replacement of stainless steel sink, 1.00 mm thick for kitchen with plug, with and incl 40mm dia CP waste coupling, waste pipe of 750mm long, washers, cantilever brackets, connecting union etc overall approx size 550 mm x 450 mm with approx bowl size of 500 mm x 375 mm x 200 mm etc, complete all as specified and directed.

S&F in replacement of stainless steel kitchen plate rack made out of imm thick sheet of size 765x920mm and 220mm deep, weight not less than 7 Kg, complete all as specified and as directed.

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, complete all specified and directed.

S&F in replacement of 3-in-1 wall mixer incl overhead Shower with 115mm long bend pipe on upperside, connecting legs & wall flanges made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.

S&F in replacement of Stop cock with long shank and cup (concealed type), 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as specified and directed.

S&F in replacement of overhead shower of dia 125 mm round shape single flow, ABS body chrome plated fancy type, with and incl swirl type shower arm of 20mm dia with wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.

S&F in replacement of bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all as specified and directed.

S&F in replacement of long body bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all as specified and directed.

S&F in replacement of handshower (health faucet) with 8 mm dia, 1.0 mtr long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.

S&F in replacement of angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated type, complete all as specified and directed.

S&F in replacement of two way angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated type, complete all as specified and directed.

S&F in replacement of bottle trap 32 mm sizewith 250 mm long wall connection pipe and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.

S&F in replacement of 15 mm bore Push tap any colour high pressure of PTMT screwed for iron pipe and fixed, (Minimum weight 15mm-47gms/ 20mm- 75gms), complete all as specified and directed.

S&F in replacement of 15 mm bore Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm- 125gms), complete all as specified and directed.

S&F in replacement of 15 mm bore Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-110gms, complete all as specified and directed.

S&F in replacement of 15 mm bore Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/ 20mm- 92gms and fixed.(Minimum weight 15mm-110gms, complete all as specified and directed.

S&F in replacement of 15 mm bore Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and directed.

S&F SS grating of squre/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all as specified and directed.

S&F in replacement of toilet roll holder with flap made of cast copper alloy, chromium plated, complete all as specified and directed.

S&F in replacement of towel rail 600 mm long and wall bracket made of cast copper alloy, chromium plated, complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.

S&F in replacement of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as specified and directed.

S&F in replacement of PVC waste pipe 32 mm dia 750 mm long with for wash hand basin or for kitchen sink, complete all as specified and directed.

S&F in replacement of waste coupling, chromium plated (half or full threaded), 32 mm dia size, complete all as specified and directed.

S&F in replacement of waste coupling, chromium plated (half or full threaded), 40 mm dia size, complete all as specified and directed.

S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all as specified and directed.

S&F in replacement of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor,complete all specified and directed.

S&F in replacement of 1st quality vitreous china ware European type WC with "P" or "S" type traps and same make plastic seat cover of white colour including flush pipe, fixing bolts etc and making good of the wall & floor surface, complete all as specified and directed.

S&F in replacement of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface, complete all as specified and directed.

S&F in replacement of 1st quality vitreous china wash hand basin, white flat/angle back, size 550x400mm, complete including necessary cutting for and pinning in ends of brackets) with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size, complete all as specified and directed.

M&L for preparation of newly steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed

M&L 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and directed. Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.

M&L 40 mm thick plain cement concrete type B1 1:2:4 (using 20 mm graded stone agg) as in floor, finished even and smooth (without using extra cement), laid in panels using 4.0mm thick & 38mm wide glass strip, panels will be not more than 1.2 x 1.2 mtr in size, laid to slope 1:30, complete all as specified and as directed. Note : The quoted rates are deemed to be inclusive of 4mm thick & 38mm wide glass strip.

M&L for 75 mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) for sub base and similar other work etc , complete all as specified and directed.

Dismantling/striping out of existing roof treatment (tarfelt, roof plaster, brick tiles, mud phuska, concrete tiles etc) including PCC padding of any description and any thickness including backing and remove the debris, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in padding levelling etc and roof kerbs complete all as specified and directed.

M&L for 15 mm thick rendering in cement morter (1:4) mixed with water proofing compound @ 0.20 Ltr/bags on roof surface when concrete is green, complete all as specified and directed. Note: WPC shall be measured and paid separately.

Supply only integral liquid water proofing compound, mixed in cement morter as per manufacturer instruction, complete all as specified and directed.

M&L for clearing the non accessible roof top surface of concrete and providing water proofing treatment to roof slab with APP based modified polymeric membrane centre core 100 micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3 kg/sqm with 100mm overlap laid as per manufacturers instructions, complete all as specified and directed with following courses of description below :- (a) Applying evenly a coat of bituminous primer confirming to IS-3384-1965 @ 0.40 kg/sqm on prepared surfaces till the surface is properly impregnated. (b) Second coat of bonding material using blown grade bitumen 85/25 conforming to IS-702 @ 1.20 kg/sqm (c) third course is laying APP based modified membrane described hereinbefore with 100mm overlap in longitudinal direction and 100mm in tranverse direction, all joints and changes in all directions should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. (d) Fourth coat of bonding materials using blown grade bitumen 85/25 confirming to IS-702 @ 1.20 kg/sqm (e) Apply a coat of bituminous aluminium paint @ 0.20 kg/sqm in case of non accessible.

M&L for clearing the accessible roof top surface of concrete and providing water proofing treatment to roof slab with APP based modified polymeric membrane centre core 100 micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3 kg/sqm with 100mm overlap laid as per manufacturers instructions, complete all as specified and directed with following courses of description below :- (a) Applying evenly a coat of bituminous primer confirming to IS-3384-1965 @ 0.40 kg/sqm on prepared surfaces till the surface is properly impregnated. (b) Second coat of bonding material using blown grade bitumen 85/25 conforming to IS-702 @ 1.20 kg/sqm ( c) third course is laying APP based modified membrane described hereinbefore with 100mm overlap in longitudinal direction and 100mm in tranverse direction, all joints and changes in all directions should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. (d) Fourth coat of bonding materials using blown grade bitumen 85/25 confirming to IS-702 @ 1.20 kg/sqm (e) cement concrete tiles of size 30cm x 30cm, 22 mm thick, machine pressed (rubber mould type), confirming to IS-13801, laid over and including 15 mm thick screed bed in CM 1:6, set and jointed and pointed with neat cement slurry and no pigment, complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B1 (20mm graded stone aggregate) in sub base, flooring, complete all as specified and directed.

M&L for factory made PU coated, machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. Note : The cost of sand cushion and plastering to edges is included in quoted rate.

M/s Jagdish Chandra Arora

m/s ramesh saran agarwal

VIJAY BUILDERS