KMC/WS/ARSM/RT2/31/2025-26

SUPPLY & DELIVERY OF 660 KW, 6.6 KV, 6 POLE , 3 PHASE, 45 DEG C AMBIENT, 51 DUTY, CACA, IP 55, IC 611, SQUIRREL CAGE INDUCTION MOTOR

DISCONNECTION OF THE MOTOR TERMINALS FROM THE EXISTING CABLES CONNECTED WITH THE FEEDER BREAKER/CAPACITOR/SOFT STARTER AND OTHER EXISTING LT CONNECTIONS VIZ. MOTOR SPACE HEATER, TEMPERATURE SCANNERS, EARTH TERMINALS ETC WITH CARE AND CAUTION FOLLOWING THE COMPLIANCE OF RELEVANT PROTECTION AND SAFETY NORMS COMPLETE IN ALL RESPECT AS PER DIRECTION OF EIC. PRE-CONDITION CHECKING AND RECORDING OF THE MEGGER VALUE, IR VALUE ETC OF THE HT MOTOR SHOULD BE RECORDED AS PER DIRECTION OF EIC. (MODE OF MEASUREMENT-DRIVE MOTOR WATT X NO OF POLES / RPM) = 660X1000X6 / 993= 4016.03

SEQUENTIAL DEASSEMBLING OF THE INSPECTION COVER/ WINDOWS/ STRAINER/ LOUVERS ETC AND DECOUPLING OF HT PUMP FROM THE DRIVE MOTOR BY REMOVING THE COUPLING BOLTS ETC. WITH CARE & CAUTION AND KEPT THE COUPLING BOLTS IN THE DEPARTMENT GODOWN & COPLETE AS PER DIRECTION OF EIC (MODE OF MEASUREMENT - DRIVE MOTOR WATT X NO. OF POLES/ RPM) = 660X1000X6 / 993= 4016.03

REMOVAL OF HALF COUPLING USING HYDRAULIC PULLER AND FIXTURES ETC VERY CAUTIOUSLY WITHOUT DAMAGING THE SHAFT AND COMPLETE AS PER DIRECTION OF EIC ( MODE OF MESURMENT : DRIVE MOTOR WATT X NUMBER OF POLES / RPM) =660X1000X6 / 993= 4016.03

FITTING AND FIXING OF HALF COUPLING BY HYDRAULIC JACK AND SPECILIZED FIXTURES AND COMPLETE IN ALL RESPECT AS PER DIRECTION OF EIC (MODE OF MEASUREMENT- DRIVE MOTOR WATT * NO. OF POLES / RPM) = 660X1000X6 / 988= 4056.78

PLACING THE COMPLETE ASSEMBLED MOTOR ON THE SOLE PLATE BY UTILIZING THE OVERHEAD CRANES AVAILABLE IN THE PUMPING STATIONS, TIGHTENING THE FOUNDATION BOLTS, FIXING THE DOWELS PINS, AND COMPLETE IN ALL RESPECT AS PER DIRECTION OF EIC. [MODE OF MEASUREMENT - GROSS WEIGHT OF THE MOTOR] 5.4 MT.

MAKING ALIGNMENT OF THE MOTOR WITH THE PUMP SHAFT BY USING DIAL GAUGE ETC INCLUDING INSERTION OF REQUSIT DIMENTIONED BRASS SHEETS ON SOLE PLATE WITH THE MAINTANENCE OF THE AIR GAP AND COMPLETE IN ALL REAPECT AS PER VDIRECTION OF EIC. [MODE OF MEASUREMENT - WATTAGE OF THE DRIVE MOTOR X NO OF POLES/RPM] = 660X1000X6 / 988= 4056.78

MAKING HT CONNECTIONS OF MOTOR TERMINALS WITH ALL EXISTING CABLES CONNECTED WITH THE FEEDER BREAKER/ CAPACITOR/SOFT STARTER AND LT CONNECTIONS AS EXISTS OF THE MOTOR SPACE HEATER/ MOTOR TEMPERATURE SCANNER AND EARTHING TERMINALS ETC COMPLETE IN ALL RESPECT AS PER DIRECTION OF EIC.

STATUTORY TESTING SUCH AS HV TESTING, SURGE COMPENSATION TESTING, CAPACITANCE TESTING, RESISTANCE TESTING, PI VALUE MEASUREMENT, TAN DELTA ETC AS PER RELEVANT IS OF HT MOTOR & COMPLETE IN ALL RESPECT WITH PROPER CARE & CAUTION AS PER DIRECTION OF EIC. (ALL TEST CERTIFICATES TO BE FURNISHED)

MAKING COUPLING THE HT PUMP WITH THE DRIVE MOTOR BY INSERTING THE COUPLING PINS ETC WITH CARE & CAUTION AND COMPLETE AS PER DIRECTION OF EIC.[ MODE OF MEASUREMENT- DRIVE MOTOR WATT X NO OF POLES /RPM] = 660X1000X6 / 988= 4056.78

DEMOUNTING THE PARTLY DEASSEMBLED INSPECTION COVER/ LOUVERS/ WINDOWS ETC OF THE HT MOTOR FROM SOLE PLATE AND PLACING THE SAME ON THE AVAILABLE WORKING FLOOR BY USING THE DEPARTMENTAL OVERHEAD CRANES ETC. WITH CARE & CAUTION WITH THE COMPLIANCE OF THE RELEVANT SAFETY & PRECAUTION NORMS 7 COMPLETE IN ALL RESPECT AS PER DIRECTION OF EIC. (MODE OF MEASURE MENT - WEIGHT OF MOTOR WITH HALF COUPLING) = MOTOR WT. + HALF COUPLING WT = 5.4 + 0.05 = 5.45 MT

COMMISSIONING THE HT MOTOR WITH LOAD AND DO NEEDFULL OBSERVATION UNDER TRIAL RUN TO ACHIVE THE SATISFACTORY OPERATION OF THE HT MOTOR WITH LOAD AND COMPLETE IN ALL RESPECT WITH PROPER CARE & CAUTION AS PER DIRECTION OF EIC.[MODE OF MEASUREMENT-PER DAY BASIS]

Sub Total

L.W.Cess @1%