Renovation Repair of Doors Windows in Vishnu Boys Hostel, Badminton Court and sewerage line in Gauri Vaishnavi Mangla Girls Hostel at UHF Nauni Solan

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas in all width and depth on plan) including getting out and disposal of excavated earth all leads, lifts and carriage of material as directed by the Engineer-in-charge .a). Ordinary rock

Providing and laying in plain cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level with 1:3:6 (one Cement: three sand : six graded stone aggregate 20 mm (twenty milimetre) nominal size etc. complete in all respect as per satisfaction of Engineer-in-Charge .

Providing and laying in plain cement concrete of specified grade excluding the cost of centering and shuttering work up to plinth level with 1:5:10 (one cement : five sand : ten graded stone aggregate 40 mm (forty milimetre) nominal size etc. complete in all respect as per satisfaction of Engineer-in-charge.

Centering and shuttering including strutting, propping etc. and removal of form for etc. complete in all respect as per satisfaction of Engineer-in-charge. a). Foundations, footings, bases of columns, etc. for mass concrete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length etc. complete in all respect as per satisfaction of Engineer-in-Charge. ( hold fast lugs or dash fastener shall be paid for separately. a).Sal wood

Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick: a) 4 mm thick glass pane (weight not less than 10 kg per sqm).

Providing and fixing Kiln seasoned and chemically treated hollock wood 30 mm thick. Glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 25 mm thick( for cup board) including ISI marked nickel plated bright finished MS piano hinges with necessary screws

Providing and fixing wire gauge shutters Kiln seasoned and chemically treated hollock wood using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with 30 mm (Thirty milimetre) thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing wire gauge shutters Kiln seasoned and chemically treated hollock wood using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with 35 mm (Thirty five milimetre) thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size etc. complete in all respect as per satisfaction of Engineer-in-charge..

Providing and fixing 2nd class teak wood 40mm into 12 mm wooden Chamfered moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing fly proof galvanized MS wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm etc. complete in all respect as per satisfaction of Engineer-in-charge a). Second class teak wood beading 20mm into 20 mm

Providing and fixing 100x58x1.90 mm ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

Providing and fixing ISI marked oxidized/ chromium plated M.S. single acting spring hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.a)150 mm ( one hundred fifty milimetre)

Providing and fixing 20 mm (twenty milimetre) dia heavy type nickel plated M.S. pipe curtain rods with nickel plated brackets etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-charge.

a) Single rubber stopper.

b) Twin rubber stopper.

Providing and fixing ISI marked oxidized/ Chromium plated M.S. Sliding door bolts with nuts and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 250x16 mm ( Two hundred fifty into sixteen milimetre)

Providing and fixing ISI marked oxidized// Chromium plated M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 200x10 mm( Two hundred into ten milimetre)

Pb). 150x10 mm( One hundred fifty into ten milimetre)

Providing and fixing ISI marked oxidized/ chromium plated M.S. handles conforming to IS:4992 with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 125 mm ( One hundred twenty five milimetre)

Providing and fixing aluminum U beading of required size to Pre-laminated/ flush door shutter, including fixing etc. complete as per direction of Engineer-in-charge.

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws andapplying a priming coat of approved steel primer, all complete as per the directionof Engineer-In-charge.

52 mm (fifty two milimetre) thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. as required. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and laying Ceramic jointless glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc complete in all respect as per satisfaction of Engineer-in-Charge (Kazaria / Nitco / Oreintbell / Somanymake).

Providing and laying Vitrified tiles Double Charged in floor with different sizes ( Kazaria/ Nitco/ Oreintbell make) (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately) etc complete in all respect as per satisfaction of Engineer-in-Charge. a) 600 x 600mm

Providing and fixing plain multipurpose cement board (Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete in all respect as per satisfaction of Engineer-in-Charge (frame work to be paid seperatately). a). 6 mm thick Cement fiber board as per IS: 14862

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-Charge. (i) Single socketed pipes a). 110 mm (one hundred ten milimetre) diameter.

Providing and fixing unplasticised – PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50 mm hard wood plugs screwed with MS screws of required length including cutting brick/ RCC work and fixing in cement mortar 1:4 ( one cement; four sand) and making good the wall etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 110 mm (one hundred ten milimetre) diameter.

Providing and fixing on wall face unplasticised – PVC moulded Coupler for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-Charge. a).110 mm(one hundred ten milimetre) diameter).

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint on steel/ wood of approved brand and manufacture to give an even shade etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work.

Finishing walls with Acrylic Smooth exterior paint of Required shade etc. in all respect as per satisfaction of Engineer-in-Charge. a). Old work (Two or more coat applied @ 1.67 ltr./ 10 Sqm) on existing cement paint surface .

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge. a).With cement mortar 1:4 (one cement : four sand)

Demolishing cement concrete manually/ by mechanical means including disposal of material within all leads etc. complete as per direction of Engineer - in – charge. a). Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Taking out doors, windows and clerestory window shutters (wood or steel) including stacking in all leads etc. in all respect as per satisfaction of Engineer-in-Charge a) Of area 3 square metre and below.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within all leads etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Area 3 sq. metres and below.

Providing & fixing White vitreous china water closet squatting pan (Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material including malba, all complete as per the direction of Engineer-in charge(Cera/ Hindware make). a) Orissa pattern W.C Pan of size 580x440 mm

Providing and fixing 10 litre capacity white P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete in all respect as per Engineer-in-Charge (Cera / Hindware make).

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast/Prayag make). a). 110mm (One hundred ten millimetre) dia

Providing and fixing 25 mm (Twenty five milimetre) thick factory made shutters of Pre-laminated HDHMR (High Density High Moisture Resistancee) board both side decorative finish conforming to IS: 12406 Grade of approved design, including fixing of heavy MS hinges 4” long etc. complete as per architectural drawing and direction of Engineer-in-Charge. (Cost of hinges will be paid for separately).

Providing and fixing Marble strips 52mm wide and 15 mm thick in joints of cement concrete floors etc. complete in all respect as per satisfaction of Engineer-in-charge.

shashikant (BID ID -542154)