Renovation and Interior Works in the office space of Directorate and Regional Directorate of National Services Scheme (NSS), 10th Floor, Jeevan Prakash Building, New Delhi

S NO DESCRIPTION AMOUNT AMOUNT AMOUNT AMOUNT

DSR Amount (After

DSR Correction NON DSR DSR+NDSR

Grand Total (DSR+NDSR) Including GST 36,136,267.00

Grand Total (DSR+NDSR) Including GST 36,136,267.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CIVIL WORKS

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

A FLOORING WORKS

CEMENT CONCRETE: Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

4.1.8 1: 4: 8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) 20.00 Cum 6812.00 136240.00

IPS FLOORING: 52mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix

2 11.4 : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's 85.00 sq m 978.45 83168.25

specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

WOODEN FLOORING: Supplying and Installation of engineered wooden flooring of total thickness 13 mm -16 mm, Toplayer PEFC controlled Core board PEFC

controlled Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue and groove Length Uniclic Width Uniclic Multifit Domestic use Conditions as per

direction of engineer in charge.

VITRIFIED TILES: Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick

cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement

4 11.41A and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch

trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed vitrified floor tiles polished finish of size

11.41A.3 Glazed vitrified floor tiles matt/Antiskid finish of size

11.41A.3.2 Size of Tile 600X600MM(Anti Skid) 19 Sqmt 1464.85 27832.15

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and

0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 1000x1000 mm

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness 1.30 to 1.50mm. Designed to

conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

RAISED FALSE FLOOR: Providing and fixing removable raised/false access flooring with systemand its components of approved make for different plenum height

with possible height adjustment upto 50mm, comprising of modular loadbearing floor panels supported on G.I. rectangular stinger frame workand G.I. Pedestal etc.

all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded

on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully

threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in

position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine

screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized ofrectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers

on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall

receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted

11.54 clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the

Engineer-in-charge.

Digitally signed by AMIT

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor

panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges:

top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist

epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed

with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm

thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm

without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250

kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification

must be printed on the side of the panel to ensure the quality of the product.

11.54.2 450mm Finished Floor Height (FFH). 9.00 sq m 5977.35 53796.15

TOTAL FLOORING WORKS 1193896.29 442000.00

B FALSE CEILING WORKS

WOODEN CEILING:Providing and fixing Laminated Wooden Ceiling Feature made of 18 mm thick mdfl board/MR grade plywood finished with approved decorative

laminate of approved shade and texture on all exposed surfaces, including backing, edge lipping, framework, all fixing hardware, accessories, making cove, cut-outs

for light fixtures, AC diffusers, sprinklers and other services, and any other incidentals required to complete the work in all respects as per approved drawings and

directions of the Architect.

1 MR The rate shall include providing and fixing supporting framework, necessary suspenders/hitech rods from the structural ceiling, edge finishing with matching 30.00 sq m 6,460 193800.00

laminate/lipping, adhesive, screws, fasteners, making vertical drops, cove details, service cut-outs, scaffolding, labour, tools and tackles, and all materials required

for proper execution and completion of the work as specified and directed by the Architect.

ACOUSTIC CEILING : Providing and fixing 9 mm thick perforated acoustic gypsum ceiling boards of approved pattern, having sound absorption properties, fixed to GI

ceiling suspension system consisting of perimeter channels, intermediate channels, ceiling sections, connecting clips, suspenders, anchor fasteners and all

accessories complete, in true horizontal level.

The perforated gypsum boards shall be backed with factory-laminated acoustic fleece/tissue to improve sound absorption and shall be screw-fixed to the GI

2 framework. The joints shall be treated with paper tape and jointing compound and finished smooth ready to receive paint. 43.13 sq m 2800.00 120752.80

The work shall include cutting and making openings for light fixtures, AC diffusers, grilles, sprinklers, smoke detectors, speakers, access panels and all other services,

including necessary supports, scaffolding, labour, materials, tools and tackles complete as per approved drawings and directions of the Engineer-in-Charge.

BAFFLE CEILING : Providing & Installation of Baffle ceiling system comprises of 50 mm x 100 mm (50 mm width & 100 mm Height) U Shape panels in RAL color finish.

Panels shall be made of 0.5 mm thick galvanized steel after Powder-coated and length up to 4000 mm. Panel shall be high corrosion resistance and good color

stability. Centre to Centre panel gap will be 150 mm. Panels are fixed on to roll formed carriers 20 mm wide x 40 mm deep out of 0.80 mm G.I sheet Powder-coated

3 MR color with cutouts to hold the panels in module of 50 mm at maximum 1200 m c/c. Carriers are suspended from the roof or truss by 6 mm dia. galvanized steel wire 15.00 sqm 8000.00 120000.00

rod hanger with special height adjustment suspension clip at max. 1200 mm c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets and nylon inserts.

Panels are factory cut in lengths up to maximum 4.0 m to suit site dimensions or shop drawings. Top cap and side cap are used to cover the edges of the panels .

GRID CEILING :Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have

Humidity Resistance (RH) of 99%,Light Reflectance ≥ 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizont

al level suspended on interlocking T-Grid of hot dippedall round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of

15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm andsecondary intermediate cross T of size 15x32 mm of length 600 mm to form grid

module of size600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50mm long 8mm outer diameter M-6 dash fasteners, 6

mm diameter fully threaded hanger rod upto 1000 mm length andL-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centreto centre along main ‘T’.

4 26.27.3 The system should rest on periphery walls /partitions with the helpof GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed tothe 90.62 sq m 1800.00 163116.864

wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S.screws. The exposed bottom portion of all T-sections used in false ceiling

support systemshall be pre-painted with polyester baked paint, for all heights. The work shall be carried out asper specifications, drawings and as per directions of

the engineer-in-charge.

With 16 mm thick beveled tegular mineral fibre Anti-microbial false ceiling tile conforming to

ISO 5 (class 100 ) specifications

Digitally signed by AMIT

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts,

other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm

with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with

connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of

20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm

5 12.45 interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including

jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also

including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with

12.45.1 12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) 250.00 sq m 1355.80 338950.00

TOTAL FALSE CEILING WORKS 502066.86 434552.80

WOODEN DOOR FRAMES: Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold

1 9.1 fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood 0.31 cu m 142949.70 44117.85

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard

2 MR. wood and well matched teak 3 ply veneering with vertical grains or cross bands and face laminate on both faces of shutters. 35 mm thick including ISI marked 39.12 SQM 3348.00 130973.76

Stainless Steel butt hinges with necessary screws

WOODEN LIPPING:Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved

3 9.112 quality and screws/nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge. 82.30 metre 102.15 8407.00

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight

4 9.83 upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 15.00 SET 1124.85 16872.75

Providing and fixing bright finished brass hanging type floor door stopper with necessary

screws, etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc.

FLUSH DOOR LOCK CYLINDER : Providing and Fixing 60 mm Eco Pin Cylinder 1CK SS Cylinder One side knob and one side regular key for

7 MR wooden doors of approved make and model all complete as per the direction of Engineer-in-charge. 15.00 each 1986.17 29792.55

8 9.72.1 Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type) 60.00 each 268.65 16119.00

9 9.75 Providing and fixing bright finished brass door latch with necessary screws etc. complete : 300x16x5 mm 15.00 each 322.20 4833.00

10 9.74.1 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm 15.00 each 441.60 6624.00

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &

double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of

11 21.18 Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). 15.00 Sqm 5325 79875.00

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body /

12 21.4.1 plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the 8.00 each 2823.85 22590.80

same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the

direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

TOTAL DOOR WORKS 214205.55 160766.31

Digitally signed by AMIT

D WALL FINISHES

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with

spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame

1 9.154 to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, 100.00 Kg 166.8 16680

switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

KOREAN : Providing and fixing Korean Stone / Solid Surface Wall Cladding of approved colour, pattern and finish, comprising 12 mm thick solid surface sheets fixed

over approved plywood backing/framework as required, including all necessary adhesives, mechanical fasteners, joint treatment, edge finishing, grooves,

mouldings, cut-outs and accessories complete.

The solid surface sheets shall be thermoformable, non-porous, homogeneous and repairable, fixed in true line, level and plumb. All joints shall be seamlessly

2 MR finished using manufacturer-approved adhesives and finishing methods to achieve a uniform monolithic appearance. 10.00 SQM 8500 85000.00

The work shall include cutting, routing, edge profiling, polishing, openings for electrical fixtures, switch boxes, access panels and other services, including all labour,

materials, transportation, scaffolding, wastage, tools and tackles complete as per approved drawings and directions of the Engineer-in-Charge.

GLASS PARTITION Providing & Fixing of Sleek Partition System SG 50 ie. Single glazed modular system consist of Aluminium section of 20*75*2 mm thick. All

sections duly anodised up to 15-20 microns with 6003 grade and required accessories ie glass to glass aluminium I sections, T section & 90 degree sections & Glass

packing to adjust the floor level. Ceiling profile & Floor profile and wall profile are 20 mm visible face and 50 mm wide. Profiles will come in three sides alongwith (

Top, Bottom and Verticle on Wall side) Forth Verticle will come where No adjusant door comes. Partition will have 10mm toughen glass & insertion of

silicon/Thermoplastic gasket to adhere the glass firm & airtight.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section

power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of

32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or

suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed

vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along

both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards

9.105.2 to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed

to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be

provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per

manufacture’s specification and direction

of engineer in charge all complete.

75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS

certification marks)

Providing and fixing thermal insulation with Resin bonded rock wool conforming to IS: 8183, density 48 kg/m3 , 50 mm thick, wrapped in 200 G virgin Polythene bags

placed over existing false ceilng and held in position by criss-crossing Gl wire

Poviding and fixing partition upto ceiling height consisting of G.I. frame and required ply board, including providing and fixing of frame work made of special section

power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of

32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or

suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed

vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along

both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards

to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed

to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be

provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws,

Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the ‘W’ profile (0.55 mm thick) having a knurled

web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange

6 MR of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with 350.00 SQM 1224.65 428627.50

fully threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the

drawing & directions of engineer-in-charge,

Digitally signed by AMIT

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work,

7 9.140.1 complete as per direc on of Engineer-incharge (Frame work shall be paid for separately). 12 mm thick commercial ply conforming to IS : 1328 BWR type 567.00 SQM 1224.65 694376.55

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work,

8 MR complete as per direc on of Engineer-incharge (Frame work shall be paid for separately). 8mm thick commercial ply conforming to IS : 1328 BWR type 283.50 SQM 1080.61 306352.94

Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden/ steel frame work,

complete as per direction of Engineer-in-Charge 6 mm thick commercial ply conforming to IS : 1328 BWR type

Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden/ steel frame work,

complete as per direction of Engineer-in-Charge 6 mm thick mdf

LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass from Saint-Gobain) of approved

color by Architect/ Client / Customer, fixed with SGG ULTRAFIX (compatible neutral core silicon/ double sided tape) on a perfectly leveled 12mm thick water proof

marine plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other structure. Lacquered glass must be made industrially (via curtain coating

process); opaque (if viewed against a support wall), coated with PU lacquer (50 micron thick); color consistency (measured by Minolta spectrophotometer

CM5081); highly durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999); environmentally friendly (no

lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial/ 6% post consumer); compressive strength (1000 MPa) & tensile

strength (40 MPa), same as float glass;

20 mm Flat VMT Panels: Supply of VMT Printed 20 mm LD PET FLAT panels which shall be processed with VMT technology for surface customization, colour options

and pattern as per the designers requirement, the panel shall be made from- -100% polyester fiber, with up to 70% recycled fiber. size of panel 2800mm x 1200mm

(± 0.5mm). Panel Should be anti fungal as per ASTM G:21 and also Non-toxic, non-irritant, and fire compliance with safety standards confirm as per BS 476 Part 6

(Fire Propagation) & Part 7 (Surface spread of flame) ,ASTM E 84 Class A, EN 13501 part 1C, S2,d0 for interior applications. Noice reduction coefficient (NRC) - 0.70

with direct fix. The product should be 100% make in india and OEM must have ISO CERTIFICATIONS- complying to- IGBC membership

ISO 14184-2 (no formaldhyde)

ISO 9001 (Quality Mangement System)

ISO 14001 (Environmental Management System)

ISO 45001 (Ocupational helth & safety management system)

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse

13 9.127.2 side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing Roller Blind system with remote consisting of a coated aluminium tube of 38 mm diameter of approved colour with provision of fabric clamping.

The Fabric is rolled up and down through a chain drive system with built in drive gear and an over run brake system. The side brackets are universal type suitable

14 MR both for wall and ceiling mounting. The bottom end of the fabric is rolled over an oval shape aluminium tube with provision to lock the fabric.The rate shall be 56.00 SQM 1614.00 90384.00

inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item .

GLASS FILM Providing & Fixing 3M & equivalent Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce Sand-blasting effect on

glass with customized designs, thickness of 2 mil (0.05mm) without adhesive & 3M & equivalentil (0.8)with adhesive having minimum tensile strength of 3.5

pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of

15 MR 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be endorsed by Electronically/computer plotter cut. Applied on glass and other rigid, clear substrates. 29 SQM 1345.00 39005.00

(partitions, doors, windows etc.) Available in 5 colours

PELMET: Fabricate and install pelmet made of 19mm thick board, up to 300mm high and in line with external glazing as per details of Architect. Rate to include

finishing exposed surfaces of the Pelmet with 1mm laminate.

17 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete 550.00 sqm 262.70 144485.00

Digitally signed by AMIT

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement

primer on wall surface having VOC content less than 50 grams/litre

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand

and manufacture, including applying additional coats wherever required to achieve even shade and colour

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and

14.1 preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) 50.00 Sqm 560.50 28025.00

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to

IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement

slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.

1.41 Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

TOTAL WALL FINISHING WORKS 2243609.15 2087070.75

SHOP DRAWINGS: Preparation of complete set of shop drawings including finishing, MEP services, details, design calcualtions etc. and for prepration of as built

1 MR drawing any other details as and when desired by Engineer Incharge/ client. A qualified professsional for the purpose shall be appointed after due appproval from 1.00 LS 360000.00 360000.00

Engineer-In-Charge.

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting,

unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable in

urban areas having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

6.13.1 Cement mortar 1: 3 (1 cement: 3 coarse sand) 25.00 sqm 1150.50 28763.00

DEMOLITION & DISMANTLING WORKS

Demolition of brickwork manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as

per the direction of the engineer in charge. In cement mortar

Dismantling door, windows and clerestory widows (steel or wood) shutter including chowkats, architrave, holdfasts etc complete and stacking within 50 metres

lead. Of area beyond 3 sq. metres

CUSTOMISED STORAGE UNIT: Supply and fixing of full height storage units (upto 450mm depth) made out of 18mm plywood finished with approved .8mm laminate

6 MR on the inside and outside. Including Glss/Handles/nuts/bolts/ all hardware etc. Hardware used of Hettich make.Compleate as per the direction of Engineer in charge 40.00 SQM 11265.00 450600.00

TOTAL MISCELLANEOUS WORKS 88976.75 810600.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ S NO DESCRIPTION UNIT QTY MR RATE DSR RATE NDSR DSR

MR AMOUNT AMOUNT

17.7.A 1 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP EACH 2 3960 7920.00

Brass single hole basin mixer of approved quality and make,

including painting of fittings and brackets, cutting and making good

the walls wherever required:- (a) White Vitreous China Wash basin

size 550x400 mm with a 15 mm CP Brass single hole basin mixer

MR 2 Supply, Installation, Testing and Commisioning of suitable EACH 2 2398.00 4796.00

compatible WASTE COUPLING 32MM- FULL THREAD- WITH

CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP

17.22A 3 Providing and fixing CP Brass 32 mm size Bottle Trap of approved EACH 2 1034.80 0.00 2069.60

quality & make and as per the direction of Engineer-in-charge

17.32.4 4 Providing and fixing mirror of superior glass (of approved quality) EACH 2 2093.00 0.00 4186.00

and of required shape and size with plastic moulded frame of

approved make and shade with 6 mm thick hard board backing :

Rectangular shape 1500x450 mm

MR 5 Providing and fixing white vitreous china extended wall mounting EACH 2 12500.00 25000.00 0.00

water closet of size 780x370x690 mm of approved shape including

seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

MR 6 Supply, Installation, Testing and Commisiong of PNEUMATIC EACH 2 8044.00 0.00 16088.00 0.00

SINGLE PIECE SLIM CONCEALED CISTERN BODY WITH

INSTALLATION KIT & “S-TYPE” DRAIN PIPE CONNECTION SET FOR

WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE)

MR 7 Supply, Installation, Testing and Commissioning of PNEUMATIC EACH 2 6641.00 0.00 13282.00 0.00

17.16A 8 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto EACH 2 349.15 698.30

1 metre long with S.S. triangular plate to Eureopean type W.C. of

quality and make as approved by Engineer - in - charge.

1 Digitally signed by AMIT

18.16.2 9 Providing and fixing brass stop cock of approved quality : 20 mm EACH 2 379.20 758.40

MR 10 Supply, Installation, Testing and Commissioning of CONCEALED EACH 2 4965.00 9930.00

STOP COCK WITH ADJUSTABLE WITH WALL FLANGE 15mm

18.53.1 11 Providing and fixing C.P. brass angle valve for basin mixer and gyser EACH 12 574.30 6891.60

points of approved quality conforming to IS : 8931 15 mm nominal

17.61 12 Cutting chases in brick masonry walls for following diameter sand

cast iron/centrifugally cast (spun) iron pipes and making good the

same with cement concrete 1:3:6 (1 cement: 3 coarse sand: 6

graded stone aggregate 12.5 mm nominal size) including necessary

plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse

18.76.1 13 Cutting holes upto 30x30cm in walls including making good the EACH 4 416.80 1667.20

same. With common burnt clay F.P.S. (non modular) bricks

18.78 14 Making chases upto 7.5 X 7.5 cm in walls including making good METRE 4 202.90 811.60

and finishing with matching surface after housing G.I. pipe etc.

18.7 17 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints complete

as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes METRE 20 335.00 6700.00

18.7.3 25mm nominal outer dia pipes METRE 20 401.55 8031.00

18.7.4 32mm nominal outer dia pipes METRE 5 518.75 2593.75

18.7.5 40mm nominal outer dia pipes METRE 5 702.95 3514.75

18.7.6 50mm nominal outer dia pipes METRE 5 934.15 4670.75

2 Digitally signed by AMIT

18.8 18 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps

at 1.00 m spacing. This includes jointing of pipes & fittings with one

step CPVC solvent cement and the cost of cutting chases and

making good the same including testing of joints complete as per

direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls

18.8.1 15mm nominal outer dia pipes METRE 20 497.80 9956.00

18.8.2 20mm nominal outer dia pipes METRE 20 537.60 10752.00

18.8.3 25mm nominal outer dia pipes METRE 5 627.25 3136.25

18.8.4 32mm nominal outer dia pipes METRE 5 739.30 3696.50

MR 20 Providing, fixing, jointing and testing in position of ISI marked UV

stabilized UPVC pipes for soil, waste, and vent, Type-B as per IS :

13592 suitable for rubber ring joints, including all neccessary

specials and fittings (confirming to IS:14735) i.e. bends, tees,

junctions (with or without doors), reducers, WC connectors,

couplers, expansion joints / bellows, cowels, clamps, rubber rings,

clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp

& hangers etc. in concealed / inside duct / under floor & basement

ceiling / external work etc. including chase cutting as required,

excavation and back filling in all kind of soils, suspended from floor

under false ceiling or embedding the pipes laid under floors /

building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size)

including cost of shuttering for proper completion of the work,

breaking and making good the walls and floors etc. after pipes have

been duly laid and tested. The rubber ring shall confirm to IS:5382.

3 Digitally signed by AMIT

The Pipes will be supported with threaded G I rods & U clamps with 0.00

nuts, washers etc on 50x50x5 mm slotted angle. The cost will

include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications

and as directed by engg-in-charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 40 536.00 21440.00 0.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 10 416.00 4160.00 0.00

MR 21 Providing, fixing, jointing and testing in position ISI marked 0.00

(IS:4985) UPVC pipes of min 6 Kg/ Sqcm rating with fitting for

waste pipe from fixtures to floor trap including reduces, enlarger,

socket, couplers, bends, tees etc including fixing at wall/ ceiling

level supported by clamp & hangers etc. cutting holes in wall/

floors/ slabs and making good the same with cement concrete

1:2:4 complete as required.

MR 22 Providing & fixing UPVC Floor trap of self cleansing design with 0.00

stainless steel grating complete in all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 5 536.00 2680.00 0.00

MR 23 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. EACH 5 726.00 3630.00 0.00

grating over floor traps.

MR 24 Providing & fixing of SS Floor Cleanout, round or square with EACH 5 1001.00 5005.00 0.00

rubber seal and flat round cover with screws and other required

fitting complete as required.

MR 25 Supply, Installation, testing and commisioning of toilet waste water EACH 2 67430.00 134860.00 0.00

super quiet portable pumping station. Pump upto vertical 5 meters

and horizontal 100 meter from toilet to vertical shaft with inlet

connection in portable pump side inlet of 50, 75, 110 as per

requirement to complete the work as per the directions of

engineer in charge

MR 26 Providing and fixing stainless steel tray below sewage pipe of size METRE 20 3629.00 72580.00 0.00

200x200x200 mm of grade SS304 including all accessories

4 Digitally signed by AMIT

MR 31 Supply, Installation, Testing and Commisiong of SOAP DISH HOLDER EACH 2 4392.00 8784.00 0.00

MR 34 Supply, Installation, Testing and Commisiong of ROBE HOOK EACH 2 2045.00 4090.00 0.00

MR 35 Supply, Installation, Testing and Commisiong of TOILET ROLL EACH 1 4978.00 4978.00 0.00

HOLDER WITH COVER

MR 36 Supply, Installation, Testing and Commisiong of TOWEL HOLDER EACH 1 3336.00 3336.00 0.00

17.10 37 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as 0.00

per IS: 13983 with C.I. brackets and stainless steel plug 40 mm,

including painting of fittings and brackets, cutting and making good

the walls wherever required :

MR 38 Supply, Installation, Testing and Commisiong of single lever sink EACH 1 8131.00 8131.00 0.00

mixer (table mounted) with extractable hand shower dual flow

complete with 1.2 m long tube with 450 mm long braided hoses

5 Digitally signed by AMIT

ELECTRICAL WORK

Sr.No. Sch.No. Particulars Qty Unit Rate as per DSR Amount MR Rate MR Amount

1 1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated 150 Nos. 1,704.00 255,600.00 -

2 1.11 copper conductor

Wiring for singlelight

twin control corepoint

in surface / recessed

1.5 sq.mm medium class PVC conduit, with modular switch,

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing

the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

3 1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC 850 Meter 373.00 317,050.00 -

4 1.14 insulated

Wiring forcopper conductor

circuit/ submain single

wiringcore cable inearth

alongwith surface/

wire with the following sizes of FRLS PVC insulated - -

copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

5 1.18 Supplying and drawing following pair 0.5 mm dia FRLS PVC - -

a 1.18.2 insulated

2 Pair annealed copper conductor, unarmored telephone 800 Meter 39.00 31,200.00 -

6 1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded 500 Meter 54.00 27,000.00 -

with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC

7 1.21 conduit asand

Supplying required.

fixing of following sizes of medium class PVC - -

conduit along with accessories in surface/recess including

8 1.24 Supplying and fixing following modular switch/ socket on the - -

a 1.24.1 existing modular plate & switch box including connections but

C 1.24.4 3 pin 5/6 A socket outlet 180 Each 136.00 24,480.00

d 1.24.5 6 pin 15/16 A socket outlet 100 Each 219.00 21,900.00

e 1.24.6 Telephone socket outlet 50 Each 168.00 8,400.00 -

b 1.24.7 TV socket outlet 3 Each 168.00 504.00 -

c RA-1 RJ45 socket cat 6 with shutter 10 Each - 421.58 4,215.78

9 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate 1 Each 402.00 402.00 -

switch box including connections but excluding modular plate etc. as required.

10 1.27 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular - -

a 1.27.1 switches in recess

1 or 2 Module etc. as required.

11 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, 40 Each 545.00 21,800.00 -

including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections

etc. as required.

12 1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, 20 Each 659.00 13,180.00 -

including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,

connections etc. as required.

13 1.35 Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto 20 Each 151.00 3,020.00 -

two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

14 1.36 Supplying and fixing stiff pendent with 300 mm long, 20 mm dia X 1.6 mm thick steel conduit, aluminium 6 Each 353.00 2,118.00 -

cast back plate and brass holder complete, including wiring the down rod with 1.5 sq. mm FRLS PVC

insulated, copper conductor, single core cable and painting etc. as required.

1 Digitally signed by AMIT

15 39.17 Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG Twisted Pair Cable -

in existing conduit/ on surface, Category 6 Unshielded Twisted Pair, 4 pair should be complied as per

UL/ETL verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in

the range of 6.1mm nominal with Operating Temperature Range : -5° to +60°C, Bending Radius : < 4 X

Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg etc. complete as required.

16 2.4 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution - -

board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

17 2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for -

inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

c 2.10.5 Three Phase & Neutral 6 Each 1,301.00 7,806.00 -

18 2.14 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit -

breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

19 2.15 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current -

circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

20 MR Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with required -

suitable number of GI couplers for joining raceways and fixing GI brackets and all accessories complete in

all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment 20 meter 3,603.00 72,060.00

(b) 225mmx38mm(GI) - 3 compartment 35 meter 2,960.00 103,600.00

21 MR Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at the

intersection of raceways supplied completely with base and cover plates, height adjustable junction box

65- 90 mm including all accessories ss plate of 3mm thick complete in all respect as per the directions of

engineer in charge

22 4.2 Supplying and installation following size of perforated painted with powder coating M.S. cable trays bends

with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with two

numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders,

fastener etc as required.

a 4.2.1 100 mm width X 50 mm depth X 1.6 mm thickness 120 Meter 948 113,760.00

b 4.2.2 150 mm width X 50 mm depth X 1.6 mm thickness 10 Meter 1105 11,050.00

c 4.2.4 300 mm width X 50 mm depth X 1.6 mm thickness 40 Meter 1544 61,760.00

23 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing 1.0 Each 8351.00 8,351.00 -

masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.

with charcoal/ coke and salt as required.

2 Digitally signed by AMIT

24 5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing 3.0 Each 15004.00 45,012.00 -

masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.

with charcoal/ coke and salt as required.

25 5.9 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including 200.0 Meter 160.00 32,000.00 -

connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by

overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

26 5.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, 50.0 Meter 1024.00 51,200.00 -

including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by

overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

27 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as 60 Meter 287 17,220.00 -

28 5.18 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with 180 Meter 50 9,000.00 -

existing surface/ recessed conduit/ submain wiring/ cable as required

29 8.1 LED Down lighter (SMD Type) (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing &

Commissioning of LED Recessed / surface Down lighter (Round /square/Rectangular) SMD type of

following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver

as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz,

Operating temp range - 15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open

circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free,

(flicker should be below 5 %), life time (LED,Driver & electrical circuitry), life time of minimum 50000

Burning Hours with , 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11

report, CCT 3000°K / 4000°K / 5700°K / 6000°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color

Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall

be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing

facilities for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated

copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty.

System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing

required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by

Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that

LED junction temperature shall not rise above 90°C).

Powder coated die cast / Extruded aluminum Body including trim.

33 8.4 LED Down lighter (COB Type) (System lumen efficacy ≥105 < 120 lm/Watt ). Supplying,

installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/

Rectangular) COB Type of following body material and construction as per IS : 10322 with driver

as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt,

frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV

with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical

circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends,

CCT 3000°K / 4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color

3 Digitally signed by AMIT

30 8.8 LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing &

Commissioning of Panel light 2x2 ft., of following body material and construction as per IS :

10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-

270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of

2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified

Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical

circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends

,CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour

Matching) required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt

output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be

submitted. Shape size and CCT shall be as approved by Engineer-inCharge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction temperature

shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body (Thickness > 1.20

31 MR Supply, Installation, Testing and Commissioning of Surface type 12W non-dimmable LED clyndical 20 Each 5,561.00 111,220.00

downlighter neutral white (4000 K) with LED having pressure die cast aluminium hang body having high

efficiency diffuser with more than 85% transmittance with rated life of L-70 @50000 hrs having system

lumen output better than 1080 lumens,with efficacy better than 90 lumen/ watt with CRI>80 & Driver

efficiency> 90% (Driver complaince IEC 62384,IEC 61547,IEC 61347-2-13,EMICISPR15, THD<10%,PF>0.95 )

etc. with inbuilt protection against short circuit,Miswiring,over voltage and surge protection upto 3 KV

including making suitable arrangement for fixing complete as required complete as reqd.

32 MR Supply, Installation, Testing and Commissioning of 20W/M LED flexible strip made of 240 LED / meter and 60 METER 1,250.00 75,000.00

Flexible FR4 PCB with copper contacts. CCT = 4000K, CRI >80.Drier shoulb 12V DC, 10Amp contant voltage

With aluminium extrusion casing.

33 MR Supply, Installation, Testing and Commissioning of Surface type 12W non-dimmable LED 40 Nos. 4,500.00 180,000.00

clyndical downlighter neutral white (4000 K) with LED having pressure die cast aluminium hang

body having high efficiency diffuser with more than 85% transmittance with rated life of L-70

@50000 hrs having system lumen output better than 1080 lumens,with efficacy better than 90

lumen/ watt with CRI>80 & Driver efficiency> 90% (Driver complaince IEC 62384,IEC 61547,IEC

61347-2-13,EMICISPR15, THD<10%,PF>0.95 ) etc. with inbuilt protection against short

circuit,Miswiring,over voltage and surge protection upto 3 KV including making suitable

arrangement for fixing complete as required complete as reqd.

34 MR Supply, Installation, Testing and Commissioning of non-dimmable Suspended 30W LED linear 10 Nos. 8,308.00 83,080.00

light(1200mm) Linear wih PBC modules & modular fixture for making continous linear

arrangement including cascading kit etc made up of extruded aluminium housing having high

efficiency diffuser with more than 85% transmittance, system lumen >3000 with luminaire

efficacy 100LPW , CRI >80 ,UGR<22 CCT 4000K. The luminaire rated life (L70) 50000 hours with

inbuilt protection against short circuit,Miswiring,over voltage and surge protection upto 3 KV

PF.0.95 and THD<10% (Driver complaince IEC 62384,IEC 61547,IEC 61347-2-13)including making

suitable arrangement for fixing including connection with 3 x 1.5 sq.mm. PVC insulated FRLS PVC

sheathed copper conductor etc as required.

4 Digitally signed by AMIT

35 MR Supply, Installation, Testing and Commissioning of non-dimmable Suspended 20w/mtr LED 5 Nos. 19,523.00 97,615.00

Curvi linear light with PBC module system & modular fixture for making continous linear

arrangement including cascading kit etc made up of extruded aluminium housing having high

efficiency diffuser with more than 85% transmittance, system lumen >3000 with luminaire

efficacy 100LPW , CRI >80 ,UGR<22 CCT 4000K. The luminaire rated life (L70) 50000 hours with

inbuilt protection against short circuit,Miswiring,over voltage and surge protection upto 3 KV

PF.0.95 and THD<10% (Driver complaince IEC 62384,IEC 61547,IEC 61347-2-13)including making

suitable arrangement for fixing including connection with 3 x 1.5 sq.mm. PVC insulated FRLS PVC

sheathed copper conductor etc as required.

36 MR Supply, Installation, Testing and Commissioning of STRETCHED FABRIC CEILING: Supply & 10 Sqm 19,931.00 199,310.00

installation of fabric false ceiling / wall formed out with TRANSLUCENT CLIPSO Plain fabric

coverings made out of polyester knitted fabric coated with Polyurethane (PU). The

TRANSLUCENT Plain Clipso fabric width of 2m, 3m, 4.1m &5.1m with weight of 200gm/m2,

thickness of 0, 3 mm. The appearance of fabric is matt, smooth and uniform with blanq color

and light transmission of 50%. The tear strength of fabric should be accordance to CH:

4,5daN; TR: 6,5 daN. The fire rating should be accordance to B-S1, d0. The fabric should be

humidity resistant and free of carcinogenic substances(CMR) or volatile organic Compounds

(VOC’s). At labeling in accordance with the French decree no. 2011- 321, Oeko-Tex

standard100 certified. Fabric should be installed with approved manufacturer guidelines. It

comes with 10- year manufacturer guarantee. The installation of TRANSLUCENT Printed fabric

should bper requirement. (Thermal management: heat sink of aluminium housing such that LED

junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium

Body (Thickness > 1.20 mm)esting facilities for LED fixtures. complete in all respect i/c

connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and

earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135

lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-

Charge as per requirement. (Thermal management: heat sink of aluminum housing such that

LED junction temperature shall not rise above 90°C).25 Kgs. The system shall

51 26.2 Online UPS- Input supply: Three Phase, Output supply: Three Phase

Supplying, installation, Testing & Commissioning of of following capacity at full load (Unity Power Factor)

at operating temperature 0 to 40 deg C, Relative humidity 0 to 95%, Online double conversion true sine

phase sequence correction. The UPS systems offered are to be of the latest technology with Digital Control

Microprocessor based for reliable operation using Insulated Gate Bipolar Transistor (IGBT)'s both for the

inductor (L) and a capacitor (C)) filters shall be included in UPS cost),

extreme power factor kit to be included to limit the input power factor (PF) to 0.99 and output power

integration, all hardware & software for iOT Communication as per approved by Engineering in charge.

d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage.

26.2.1 f)Temperature:

10KVA (Each PowerSTS, Inverter, PFC. be

module shall g) Event Logging & Statistical Data (On LCD/LED): UPS should capture

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz power distribution system. The - -

panel shallLTbePanel

The Main Indoor, free

shall usestanding,

all draw floor mounting,

out type sheet

breakers metal

suitable forclad,

V AC, 3 dead front,

50 Hz, and vermin

supply system. Panel shall have Buscoupler switching, auto operation of incommer and bus coupler, auto

Air Circuit Sets, auto

Breaker withD.G. running by pre

microprocessor set timing,

release auto changeover

ge metering etc and

& LCD display having

, with readyfollowing

to clsoe indicator, - -

INCOMINGhave capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet and as per the detail - -

5 Digitally signed by AMIT

1 Nos. 160 Amp TPN MCCB 25KA LSIG having S/C, E/F O/C protection, LCD Display having specs as per

attached annexture From 100KVA Transformer having

1 Nos.Phase indication

63 Amp Lamp 25KA

TPN MCCB with control MCB S/C, E/F O/C protection, LCD Display having specs as per

attached annexture

Buscoupler: 63 AmpFrom 100KVA Transformer having

Outgoings - -

1 Nos. 100 Amp FP MCCB 25 KA - -

2 Nos. Amp Status Indication

FP MCB 25 KA with control MCB - -

3 Nos. Amp Status Indication

DP MCB 10 KA with control MCB - -

Short Trip Status

Circuit Indication

Breaking capacitywith control

should MCBthan 50KA.

RELAYS AS PER SLD - -

6 Digitally signed by AMIT

SCHEDULE OF QUANTITIES - HVAC WORKS

S No DSR 2025 DESCRIPTION UNIT QUANTITY RATE

DSR (INR) NON-DSR (INR)

31.3.3 Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable per HP 38 21659.00 823042.00

Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically

sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with individual

separate PCB) for above 14HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration

Isolators with suitable foundation etc. complete as required. To have better efficiency condenser

fan shall be capable to operate at different speed with respect to load. The unit shall deliver the

rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even

at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the

rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3

Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the

refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film

to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion,

and reduce the risk of degradation, thereby improving overall performance and durability. The

Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation

and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification,

connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40

and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC

2 DSR 2025 - INDOOR UNIT

7.4 Supply, Installation, Testing and Commissioning of following minimum

capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with

synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower,

multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain

pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for

operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units

must shut down upon receiving a singal from the

BMS System/Fire Signals. The system shall be capable to adjust air flow as

per room requirement in auto mode. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB

temperature. (Make will be same as of Outdoor)

4-Way Cassette type

HI - WALLSPLIT SYSTEMS

Digitally signed by AMIT

32.2 Supply , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners

complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping

with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU),

copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R407 Green Refrigerant,

wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and

50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of

following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the

3 rated capacity upto 42 Degree Celsius. Min 5 year Original Equipment Manufacturer (OEM)

warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694

or IS 9968 temperature sensing control IS /International Electro technical Commission (IEC)

60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS

12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able

to operate up to 50 0C (out door ambient temperature).

4.0 MR Corded Remote controls Nos 2 4733 9466.00

5 MR Communication cable (1.5 sqmm X 2 Core) RMT 20 385 7700.00

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T" Joints

i.e. Refnet Joints/ Header with Insulation for refrigearnt piping

Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete

with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including

6 31.14 accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for

Suction and Liquid lines, all accessories as per

specifications etc. as required :

6.1 31.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm m 150 487.0 73050.00

6.2 31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm m 150 615.0 92250.00

6.3 31.14.6 22.2 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm m 200 739.0 147800.00

6.4 31.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm m 100 487.0 48700.00

6.5 31.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm m 100 615.0 61500.00

6.6 31.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm m 100 739.0 73900.00

CABLE TRAY FOR REFRIGERANT PIPING

Supplying and installing of following size of perforated hot dip galvanized G.I cable tray

with perforations not more than 17.5%, in convenient sections, joined with connectors,

7 MR suspended from ceiling with G.I suspenders including bolts and nuts, etc. for carrying

refrigerant pipe in outdoor application as required.

7.1 450 mm width x 62.5 mm depth x 2 mm thickness Rmt 10 1,325 13250.00

7.2 225mm width x 50 mm depth x 1.6 mm thickness Rmt 45 962 43290.00

CONDENSATE DRAIN UPVC PIPE

Digitally signed by AMIT

Supply, installation, testing and commissioning of uPVC Pipe ,complete with fittings,

8 supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and accessories as

per specifications, drawings.

6 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as

Total HVAC-VRV WORKS 2876105.00 285780.00

Digitally signed by AMIT

S NO DSR 2025 DESCRIPTION UNIT DSR RATE DSR AMOUNT NDSR RATE NDSR AMOUNT

1 28.2.1.2 Supplying, installation, testing and commissioning of micro processor

based intelligent addressable main fire alarm panel, central processing

unit with the following loop modules and capable of supporting not less

than 240 devices (including detectors) and minimum 120 detectors per

loop and loop length up to 2 km, network communication card,

minimum 320 character graphics/ LCD display with touch screen or

other keypad and minimum 4000 events history log in the non volatile

memory (EPROM), power supply unit (230 ± 5 % V, 50 hz), 48 hrs back-

up with 24 volt sealed maintenance free batteries with automatic 1 Each 250,420.00 250,420.00

charger. The panel shall have facility to connect printer to printout log

and facility to have seamless integration with analog/digital voice

evacuation system (which is part of the schedule of work under SH: PA

System) and shall be complete with all accessories . The panel shall be

compatible for IBMS system with open protocol BACnet/ Modbus over

IP complete as per specifications.

2 28.2.2 Supplying, installation, testing & commissioning of central graphical fire

alarm management system to centrally monitor and operate the fire 1 Each 210,264.00 210,264.00

alarm system complete as required.

3 28.2.3 Supplying, installation, testing & commissioning of repeater panel with

320 character/ Touch screen LCD display with inbuilt reset, acknowledge 1 Each 113,734.00 113,734.00

and silence switches complete as required.

3 28.2.4 Supplying, installation, testing & commissioning of intelligent analog

addressable photothermal detector complete with mounting base 60 Each 3,004.00 180,240.00

complete as required

4 28.2.5 Supplying, installation, testing & commissioning of response indicator

on surface/recessed MS Box having two LED, metallic cover complete 40 Each 306.00 12,240.00

with all connections etc as required.

5 28.2.7 Supplying, installation, testing & commissioning of fault isolator

complete with base as required.

6 28.2.9 Supplying, installation, testing & commissioning of intelligent

addressable thermal detector with rate of rise cum fixed temperature 40 Each 2,866.00 114,640.00

thermistor complete with base as required.

7 28.2.10 Supplying, installation, testing & commissioning of addressable fire

control module complete as required.

8 28.2.11 Supplying, installation, testing & commissioning of addressable phone

control module complete as required.

9 28.2.13 Supplying, installation, testing & commissioning of intelligent

addressable duct detector including suitable Photo detector complete 3 Each 8,183.00 24,549.00

with base as required.

1 Digitally signed by AMIT

10 28.2.14 Supplying, installation, testing & commissioning of addressable manual

call point complete as required.

11 28.2.15 Supplying, installation, testing & commissioning of addressable horn

cum strobe complete as required 4 Each 3,682.00 14,728.00

12 28.2.17 Supplying, installation, testing & commissioning of fire fighter telephone

handset complete as required. 2 Each 6,016.00 12,032.00

28.3.1 Supplying, installation, testing & commissioning of 6 zone, voice alarm

controller with USB, MP4 player (including 6 zone button paging station)

with seamless integration facility with main fire alarm panel for voice

evacuation complete as required. 1 Each 132,115.00 132,115.00

28.3.2 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling

speaker complete as required.

28.3.6 Supplying, installation, testing & commissioning of digital audio

amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as 1 Each 101,150.00 101,150.00

12 MR SITC of Call station with soft touch button 15 freely programmable 178,560.00 178560

buttons,Customization via built-in display and keys, Provision for

installing emergency button and key switch,EN 54-16 system

certification etc all required

18 MR Supplying & Fixing of battery operated illiminated "EXIT" signage, 4,256.00 42560

with 2hrs power Battery backup complete as required.

ASPIRATION DETECTOR ACCESSORIES

15 28.5.2 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,

600/1000V rated with annealed copper conductor having XLPE

insulation, steel wire armouring & FRLS/HFFR outer sheath complete as

16 28.5.3.4 Supplying and drawing of cable Fire Retardant PVC insulated copper

conductor cable in the existing surface / recessed steel conduit of

following pairs, cores and size including connections and 1200 Mtr 171.00 205,200.00

interconnections etc. as required. speaker cable Four pair, 2-core, 1.5

17 28.5.4 Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along

with all ancillaries and accessories like coupler etc. as required 500 Mtr 60.00 30,000.00

2 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Providing and fixing ISI Marked of approved make Fire

4 Extinguishers complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 8 NOS 12912.00 103296.00

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

TOTAL 164720.00

Digitally signed by AMIT

BILL OF QUANTITIES - FURNITURE

SNO. Item Specification Qty Unit Price Amount

1 MD room table Supplying and placing in position Main Table of the following specifications.3000 x 1050 x 740 MAIN WORKTOP :Made of 43mm Thick (±1)

combination of MDF and particle board with top LAMINATED facecoated with clear lacquer. All edges are edge banded with matching

1mm thick veneerlipping.

LEATHER PAD:Made of 18mm Thick (±1) MDF with Leatherette wrapped around top surface. Thisleather pad is fixed to main top panel.

DRAWER UNIT:Top panel and drawer unit modesty panel is made of 43mm Thick (±1) combination ofMDF and particle board with top

laminatesface coated with clear lacquer. All thicknessedges are edge banded with matching lipping. Remaining construction is of 18mm

Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade confirming to IS-12823:1990, Edge banded with matching 2 mm

thickPVC lipping. Bottom panel of drawer is 9mm thick particle board with leatherette on topsurface.Drawer unit is provided with soft

closing channels for smooth opening and closing.Drawer unit is secured with side central lock.OPEN STORAGE UNIT:Top panel and open

storage unit modesty panel is made of3mm Thick (±1) combination of MDF and particle board with top Laminated face coated with clear

lacquer. Allthickness edges are edge banded with matching lipping.Remaining construction is of 18mm Pre-laminated twin board (PLT) of

E1-P2 grade andapproved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping.MODESTY:Made of

18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching

2 mm thick PVClipping. Modesty is fitted with aluminum trims.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of 2 251608.20 503216.40

E1-P2 grade and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door is fixed with soft

closing hinges and handle is provided for ease of opening.Also lock is provided on side panel for security.ACCESS FLAP WITH POWER

BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2 USB powerpoints, 1 HDMI connection, 1 inbuilt misc. cable

grommet and CAT 3 and CAT 6connections.HIDDEN WIRELESS MOBILE CHARGER:It will only be available in 3000mm main table. It is fitted

below leather pad.Supplying and placing in position height adjustable ERU of the following specifications.1500 x 600 x 610 ERU TOP

PANEL:Made of 43mm Thick (±1) combination of MDF and particle board with top laminatesfacecoated with clear lacquer. All edges are

edge banded with matching 1mm thick veneerlipping. Top panel is provided with elliptical cable cover which contains 2 USBs, 1Universal

socket, 1misc. cable grommet, 1 HDMI connector and 1 CAT-6 connector.

UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade confirming to IS-12823:1990,

Edge banded with matching 2 mm thick PVClipping. DOOR PANELS:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade

and approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door panels are provided with lock.

ERU HEIGHT ADJUSTABLE LEG:The Leg consist of Outer and Inner Aluminum Extrusions (AL 63400 - WP). The Worksurface moves up &

down due to the extension and compression of smooth functioninggas lift with adjustable height and consistent motion during operation.

2 MD Back unit The gas lift and

Providing isactuated using

placing Backlever mechanism,

of size 3000 manually. WORKTOP

mm(L)x470mm(D SUPPORT FRAME:The Worktop

x2325mm(H).CONSTRUCTION Support

AND Frame consist

MATERIAL: Madeoffrom

combination of Top panel(0.5mm CRCA), side panel(0.5mm CRCA), Bottom panel(0.5mm CRCA for 600W and 0.8mm CRCA

for 1200W), Back panel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End Cover(0.5mm CRCA). Shelves are 12

bend panel made of 0.7mm Thick CRCA (D Grade, IS-513). 4 nos of shelves for 1950H and 5 nos of shelves for 2325H back

unit. Storage body is powder coated with Epoxy Polyester to the thickness of 50 microns (+/-10 micron). Finish Laminate

DOOR: Made of 12mm Thick (±1) MDF with 3.5mm laminatesboth side and face coated with clear lacquer. All edges are edge

banded with matching 1mm thick laminate lipping. Door is provided with soft closing hinge. Handle is also provided for ease of

opening. Storage is secured with 3 way cam lock.GLASS DOOR: Made from the combination of aluminium alloy (63400)

extrusion and 4mm clear toughened glass. Aluminium extrusion of glass doors are powder coated with Epoxy Polyester to the

thickness of 50 microns (+/-10 micron). Handle is provided for ease of opening. RH Glass Door is provided with 3 way cam lock

3 MD main chair Proving and placeing High back chair: SEAT ASSEMBLY :The seat assembly is made up of 15mm thick moulded plywoodlayered with

assembly of P.U foam of 45 kg/m3 density and slabstock foam of 28 kg/m3 density and whole sub-assembly is then

upholstered with leatherette cover.

2. BACK ASSEMBLY :The back assembly is made up of 12 mm thick moulded plywood

layered with P.U foam of 45 kg/m3 density and U-foam of 28kg/m3 density. A 200 GSM recron sheet is placed over the P,U foam and

whole sub-assembly is upholstered with leatherette cover,

3, ARMRESTS (FIXED) : The armrest is made of die cast aluminium with buffing finish.

4, CENTER TILT WITH MULTI POSITION LOCK MECHANISM: The mechanism is designed with the following features:

- 3 position locking

- Tilt tension adjustment

5, PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has a stroke of 10.0$0.3cm.

6, PEDESTAL ASSEMBLY :The pedestal is made of high-pressure die-cast polished aluminum with a buffed outside surface and black color

coated internal surface. It is fitted with 5 castors and has a pitch-center diameter of 67.5t0.5 cm.

4 Visitor chair Proving and placeing mid back chair: SEAT ASSEMBLY :The seat assembly is made up of 15mm thick moulded plywoodlayered with

assembly of P.U foam of 45 kg/m3 density and slab stock foam of 28 kg/m3 density and whole sub-assembly is then

upholstered with leatherette cover.

2. BACK ASSEMBLY : The back assembly is made up of 12 mm thick moulded plywood

layered with P.U foam of 45 kg/m3 density and U-foam of 28 kg/m3 density. A 200 GSM recron sheet is placed over the P,U foam and

whole sub-assembly is upholstered with leatherette cover,

3, ARMRESTS (FIXED) : The armrest is made of die cast aluminium with buffing finish.

4, CENTER TILT WITH MULTI POSITION LOCK MECHANISM: The mechanism is designed with the following features:

- 3 position locking

- Tilt tension adjustment

5, PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic

height adjustment has a stroke of 10.0$0.3cm.

6, PEDESTAL ASSEMBLY :

The pedestal is made of high-pressure die-cast polished aluminum with a buffed outside surface and black color coated internal surface. It

is fitted with 5 castors and has a pitch-center diameter of 67.5t0.5 cm.

5 3 seater sofa Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shallbe 1820W x 905D x 855H. The seat

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ±

2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with

Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or

leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 2 56297.86 112595.72

3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly

made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

6 1 seater sofa Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ±

2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with

Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or

leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 4 50067.87 200271.49

3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly

made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

7 Center table TABLE MATERIALS: Glass of 08 mm thk tempered, Solid rubber woood legs and frame, MS sheet as bottom shelf .DECORATION MATERIALS

& SPECIFICATIONS: (DENSITY / TYPE): PU coating to the rubber wood parts, clear glass Rubber wood understructure with 12 mm tempered

glass top. MS sheet at the base, with a laser-cut floral design, can be used as a display shelf.Tapered legs with enhanced aestheticsOverall

8 Corner table Overall Size : Width : 60cm Depth : 60cm Height : 45cmTABLE MATERIALS: Glass of 08 mm thk tempered, Solid rubber woood legs and

frame, MS sheet as bottom shelf .DECORATION MATERIALS & SPECIFICATIONS: (DENSITY / TYPE): PU coating to the rubber wood parts,

clear glass Rubber wood understructure with 12 mm tempered glass top. MS sheet at the base, with a laser-cut floral design, can be used

as a display shelf. Tapered legs with enhanced aesthetics

9 APA/DPA room main Supplying and placing in position Main Table,ERU & pedestal of the following specifications. 2350x2350x750 Primary Work Surface Made

table of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing

access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF

one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm

thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.

Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge

banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and

approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick 3 168827.08 506481.25

MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-

BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft

closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

10 main chair Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood

& seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded

Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give

comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair

seat & back size are

HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H)

SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2

kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast

aluminium with buffing finish designed with the following features :

· Up-Down adjustment–7 steps (7.0 ± 0.5cm range)

· It has to & fro movement along with Swivel adjustment.

CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features:

· 360° revolving type.

· 3 position locking with anti shock mechanism.

· Tilt tension adjustment

PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm.

PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal

is 67.0 ± 0.5cm pitch-center dia.

(77.0 ± 1.0cm with castors).

TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 77.0 CM.

DEPTH (D): 77.0 CM.

HEIGHT (H): 110.5-120.5 CM.

SEAT HEIGHT (SH): 44.5-54.5 CM.

11 Visitor chair Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood

& seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded

Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give

comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair.

The chair seat & back size are

FULL BACK SIZE 51.5 cm. (W) x 69.0 cm. (H)

SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2

kgf as per IS:7888 for 25% compression.

ARMRESTS : The 3-way adjustable armrest is is made of die-cast

aluminium with buffing finish designed with the following features :

· Up-Down adjustment–7 steps (7.0 ± 0.5cm range)

· It has to & fro movement along with Swivel adjustment.

CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: 9 25390.83 228517.44

· 360° revolving type.

· 3 position locking with anti shock mechanism.

· Tilt tension adjustment

PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm

PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal

is 67.0 ± 0.5cm pitch-center dia.

(77.0 ± 1.0cm with castors).

7. TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 77.0 CM.

DEPTH (D): 77.0 CM.

HEIGHT (H): 98.0-108.0 CM.

SEAT HEIGHT (SH): 44.5-54.5 CM.

12 2 seater sofa Dimensions W x H x D (cm)- 127.5 x 83.5 x 80

Finish Color - Fab Brown

Seat Height (cm) - 46.5

Upholstery Material - Synthetic Leather

Warranty - 1 Year Warranty 1 30259.74 30259.74

Primary Material - Leatherette

Aesthetically pleasing, mid-back designer backrest with tufts and clean stitching. • Rounded armrests with soft foam seating provide

ergonomic comfort. • Easy-to-clean synthetic leather or fabric for the cool touch and feel.

13 1 seater sofa Dimensions W x H x D (cm)- 81 x 83.5 x 80 .

Finish Color - Fab Brown

Seat Height (cm) - 46.5

Upholstery Material - Fabric

Warranty - 1 Year Warranty

Primary Material - Pinewood

Aesthetically pleasing, mid-back designer backrest with tufts and clean stitching. • Rounded armrests with soft foam seating provide

ergonomic comfort. • Easy-to-clean synthetic leather or fabric for the cool touch and feel.

14 Center table Overall Size -L x W x H – 1100 x 597 x 455 ,Table-top – 18 mm thick PLT Board in Noce

Versailles Light [Brown]

PLT – 18 mm thick in Noce Versailles Light & Black Ink 1 12198.07 12198.07

Configuration – Shelf storage

15 Corner table L x W x H – 597 x 597 x 605

Table-top – 18 mm thick PLT Board in Noce Versailles

PLT – 18 mm thick in Noce Versailles Light & Black Ink 1 10633.45 10633.45

Configuration – Shelf storage

16 YO/PA/Cabin main Supplying and placing in position Main Table & ERU of the following specifications. Its size shall be 1500 Width mm x 750 Depth mm x 740

table Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing

laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with

1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. ERU size shall be 1050 Width x 450 Depth

x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed

laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick

plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading.

17 Main chair Providing, supplying and placing of high Back Chair. SEAT ASSEMBLY: The seat is made up of 1.5±0.1 cm thick hot-pressed plywood

upholstered with fabric and moulded polyurethane foam. SEAT SIZE: 51.8cm (W) x 49.7cm (D)

BACK ASSEMBLY: The Back is injection moulded in glass filled Polypropylene which is 2 upholstered with Mesh fabric. The back consist of

adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 10.1 cm.

BACK SIZE: 47.9 cm(W) x 66.9 cm (H)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m and hardness 14 ± 2

18 Visitor chair kgf as per IS:7888

Providing, forand

supplying 25%placing

compression. ARMRESTS

of Mid Back (ADJUSTABLE):The

Chair. SEAT height

ASSEMBLY: The seat adjustable

is made up armrest is made

of 1.5±0.1 of Polypropylene

cm thick and can be

hot-pressed plywood

upholstered with fabric and moulded polyurethane foam.

SEAT SIZE: 51.8cm (W) x 49.7cm (D)

BACK ASSEMBLY: The Back is injection moulded in glass filled Polypropylene which is 2 upholstered with Mesh fabric. The back consist of

adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 10.1 cm.

BACK SIZE: 47.9 cm(W) x 66.9 cm (H)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m and hardness 14 ± 2

kgf as per IS:7888 for 25% compression. ARMRESTS (ADJUSTABLE):The height adjustable armrest is made of Polypropylene and can be

adjusted to 6.010.1cm height it also has swivel and To and Fro adjustment with moulded PU armtop

ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features 360° revolving type Front-

pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort Till tension adjustment can be operated in

seating position 5 position Tilt limiter giving option of variable sit angle to the chair Seat/back tilting ratio of 1:2

The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron) PNEUMATIC HEIGHT ADJUSTMENT:

The pneumatic height adjustment with an adjustment stroke of 10.0±0.3cm.

PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The

pedestal pitch-center dia is 166.1±0.5 cm.(76.1 ± 1.0 cm. with castors).

TWIN WHEEL CASTORS: The twin wheel castors are Injection moulded in black Polyamide having 6.01 0.1cm wheel Diameter.

WIDTH (W) - 76.0cm

DEPTH (D) - 76.0cm

HEIGHT (H) - 95.5 cm- 105.5cm

SEAT HEIGHT - 43.5 - 54.0cm

19 Worksatation Supplying of workstation of size 1200 X 600x 750 with KBPT .Providing DESK based modular workstation with worktop

1200X600mm thickness 25mm System ht - 750 mm .Understructure - The slanted legs with perforated metal modesty in between are

connected to the understructure with the help of PDC Connectors to provide a stable and sturdy base for the worktops. Modesty

panel shall be of Metal 1.2 mm thick CRCA. Wire Management : Metal powder coated power box with wire raiser+D56 is given

to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop

above power box cut out for accessing switches.Worktop mounted metal modesty made from 0.8 mm thk CRCA (IS: 513) is

provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 28 44483.82 1245546.88

mm d.Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht

3dr = 2box+1file. .The product should be GREENPRO, SCS IAQ, GRIHA, BIFMA certified.

20 chair Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood

and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give

comfort to popliteal area.

The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar

support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm.

The chair seat & back size are *SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H) HIGH RESILIENCE (HR)

POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf as per IS:7888 for 25%

compression. ARMRESTS :The adjustable armrest is designed with the following features :· Up-Down adjustment– 6 steps (7.2 ± 0.5cm

· Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled Nylon insert.

CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism isdesigned with the following features:

· 360° revolving type.

· 3 position locking with anti shock mechanism.

· Tilt tension adjustment

PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm.

PEDESTAL ASSEMBLY : The pedestal is injection moulded in glass-filled Nylon andfitted with 5 nos. twin wheel castors. The pedestal is 66.1

±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors).

TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 76.1 CM.

DEPTH (D): 76.1 CM.

HEIGHT (H): 101.5 - 111.0 CM.

SEAT HEIGHT (SH): 44.5 - 54.0 CM.

21 Board room table Supplying and placing in position conference table of the following specifications with following size shall be 2350W - 2350 X 850 X 740, 2

STR END_RH - 1350 X 600 X 740 Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade

conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to

wires and cables. Work top is available in various shapes. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2

grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP

profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-

laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC

lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 1 343671.11 343671.11

513,epoxy polyester powder coated (DFT 40-60 microns). Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy

polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is

provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video

cables onto worktop and connect devices charger to power socket below worktop.

22 Main chair Providing, supplying and placing of high Back Chair. SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood

and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give

comfort to popliteal area.

The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar

support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm.

The chair seat & back size are SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf

as per IS:7888 for 25% compression. ARMRESTS :The adjustable armrest is designed with the following features :· Up-Down adjustment– 6

steps (7.2 ± 0.5cm range)

· Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled Nylon insert.

CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism isdesigned with the following features:

· 360° revolving type.

· 3 position locking with anti shock mechanism. 1 17065.63 17065.63

· Tilt tension adjustment

PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm.

PEDESTAL ASSEMBLY : The pedestal is injection moulded in glass-filled Nylon andfitted with 5 nos. twin wheel castors. The pedestal is 66.1

±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors).

TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 76.1 CM.

DEPTH (D): 76.1 CM.

HEIGHT (H): 101.5 - 111.0 CM.

SEAT HEIGHT (SH): 44.5 - 54.0 CM.HEADREST: The Headrest sub-assembly is made up of injection moulded glass filled Polypropylene which

is upholstered with moulded HR polyurethane foam and fabric. It has an adjustment of 4.0 ± 0.1cm & it is assembled over Thrill mesh back

chair. The complete headrest assembly is retro fit to the main chair.

23 Visitor chair Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood

and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give

comfort to popliteal area.

The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar

support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm.

The chair seat & back size are

*SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf

as per IS:7888 for 25% compression.

ARMRESTS :The adjustable armrest is designed with the following features :· Up-Down adjustment– 6 steps (7.2 ± 0.5cm range)

· Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled Nylon insert.

CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism isdesigned with the following features:

· 360° revolving type.

· 3 position locking with anti shock mechanism. 46 15572.93 716354.87

· Tilt tension adjustment

PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm.

PEDESTAL ASSEMBLY : The pedestal is injection moulded in glass-filled Nylon andfitted with 5 nos. twin wheel castors. The pedestal is 66.1

±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors).

TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 76.1 CM.

DEPTH (D): 76.1 CM.

HEIGHT (H): 101.5 - 111.0 CM.

SEAT HEIGHT (SH): 44.5 - 54.0 CM.

24 Multipurpose table Supplying and placing in position conference table of the following specifications with overall size shall be 3000 X 1150 X 740.Work top-

Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping. Access panels provided with soft closing hinges

Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved

shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is

added at bottom edges for improving the aesthetics. The product has a knock-down construction.

Wire Raiser-A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and 1 60332.22 60332.22

cables. Cutout provision below Access flap at two locations for standard 8 module Anchor Roma is provided. Beside each cutout, an

additional cutout with plate is provided for mounting Audio Visual Cables (eg.HDMI, VGA-A,etc).

25 Chair Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood

and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give

comfort to popliteal area.

The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar 8 15572.93 124583.46

support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm.

The chair seat & back size are

*SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H)

26 Waiting lounge 3 seater sofa

3 STR Dimensions W x H x D (cm):- 202 x 97.5 x 89

2 STR Dimensions W x H x D (cm) 157 x 97.5 x 89

upply ,Fitting & Fixing of Herman Miller/Haworth/Godrej/Steelcase make BIFMA Level 2, Greenguard (by UL), Greenpro, AIOTA, Greenco

Platinum Certificate, Indoor Advantage Gold, Indian Design Mark, GRIHA, Indoor Air Monitoring Report Certified manfacturer Make

Bayflow 1-Seater Sofa as per following specification.

• Understructure: Understructure of seat is made up of combination of pinewood members and 12mm thick Plywood. Pinewood are

of cross sections 34x64mm, and 16x30mm without having major knots & defects on the surface

Complete understructure of Seat is made by gluing, nailing & stapling, Non-woven fabric of 1O0GSM is stapled on the top surface after

attaching Zig-Zag spring to cover the structure.

•Foam: Foaming of seat is done with and 28kg/m* PU foam. A top layer of supemoft PU foam with density 32 kg/m^ is used to provide

• Understructure: Understructure of armrest is made up of combination of pinewood members,12mm thick Plywood. Pinewood are of

cross sections 16X35mm without having major knots & defects on the surface. 1 83192.24 83192.24

Complete undemtructure of Armrest is made by gluing, nailing & stapling.Rubber wood panel 18mm to be fitted just after the upholstery is

done or before assembling the armrest

• Foam: Foaming of Armrest is done with density 60kg/m^ and 28kg/m^ on all the outer surfaces in order to give definition to the form of

armrest.Foam of 28kg/m* is used on the top surface of armrest.

•FACIA PANEL: Facia panel is having wood-stain matt finish. It is fitted to the armrest with the help of Velcro-strip.

Backrest : (1 Seater, 2 Seater, 3 Seater)

•Understructure: Understructure is made up of combination of pinewood members, 12mm THK Plywood, HDPE sheet at the rear side of

the backrest at the bottom side of the backrest ear

Pinewood are of cross sections 16x35, 22x64mm, 22x40mm without having

major knots and defects on the surface. HDPE sheet is to be stapled on the rear side of backrest.

•Foam: Backrest is made of PU foam with density 6Okg/m^ and 28kg/m* and 32kg/m3. Backrest Lumber foam is of 32kg/m covered with

layer’s of recron sheet of 200gsm.

. Cushion :(1 Seater, 2 Seater, 3 Seater)

27 2 seater sofa Backrest neck cushion

3 STR Dimensions WxH are

202of detachable

x 97.5 x 89 pillows which are connected with the help of Velcro strip of (2 inch). Backrest cushion

2 STR Dimensions W x H x D (cm) 157 x 97.5 x 89

upply ,Fitting & Fixing of Herman Miller/Haworth/Godrej/Steelcase make BIFMA Level 2, Greenguard (by UL), Greenpro, AIOTA, Greenco

Platinum Certificate, Indoor Advantage Gold, Indian Design Mark, GRIHA, Indoor Air Monitoring Report Certified manfacturer Make

Bayflow 1-Seater Sofa as per following specification.

•Understructure: Understructure of seat is made up of combination of pinewood members and 12mm thick Plywood. Pinewood are of

cross sections 34x64mm, and 16x30mm without having major knots & defects on the surface

Complete understructure of Seat is made by gluing, nailing & stapling, Non-woven fabric of 1O0GSM is stapled on the top surface after

attaching Zig-Zag spring to cover the structure.

•Foam: Foaming of seat is done with and 28kg/m* PU foam. A top layer of supemoft PU foam with density 32 kg/m^ is used to provide

• Understructure: Understructure of armrest is made up of combination of pinewood members,12mm thick Plywood. Pinewood are of

cross sections 16X35mm without having major knots & defects on the surface. 2 68962.74 137925.48

Complete undemtructure of Armrest is made by gluing, nailing & stapling.Rubber wood panel 18mm to be fitted just after the upholstery is

done or before assembling the armrest

• Foam: Foaming of Armrest is done with density 60kg/m^ and 28kg/m^ on all the outer surfaces in order to give definition to the form of

armrest.Foam of 28kg/m* is used on the top surface of armrest.

•FACIA PANEL: Facia panel is having wood-stain matt finish. It is fitted to the armrest with the help of Velcro-strip. Backrest : (1 Seater, 2

Seater, 3 Seater)

•Understructure: Understructure is made up of combination of pinewood members, 12mm THK Plywood, HDPE sheet at the rear side of

the backrest at the bottom side of the backrest ear Pinewood are of cross sections 16x35, 22x64mm, 22x40mm without having major

knots and defects on the surface. HDPE sheet is to be stapled on the rear side of backrest.

•Foam: Backrest is made of PU foam with density 6Okg/m^ and 28kg/m* and 32kg/m3. Backrest Lumber foam is of 32kg/m covered with

layer’s of recron sheet of 200gsm.

. Cushion :(1 Seater, 2 Seater, 3 Seater) Backrest neck cushion are in the form of detachable pillows which are connected with the help of

Velcro strip of (2 inch). Backrest cushion consist of 50mm thk 32density PU foam and wrapped with layer of 200gsm recron sheet.

28 corner table Upholstery:

Overall Size :For color: 120cm

Width combination

: 60cmfefer latest

Height color chart

: 36.7cm as there

Materials : All are single-tone

carcass as made

panel are well asofdual-tone option for Leatherite

18 mm prelaminated fabric.

with edge banding 1.5 mm thickness.Drawer bottom is made of .9 mm thick prelaminated particle board .Drawer front is made of 18 mm

thick PU painted MDF . Legs : Rubber wood . Hardware : Hettich . Construction : Knock down .Finish : All 18 mm prelaminated particle

board panels are Noce Versaillies with walnut edge band. PU lamination is high gloss in Ecru shade .Packets : 1 nos . Materials : All carcass

panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness. Hardware : Hettich . Construction : Knock

down .Finish : • All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band . PU lamination is high gloss in

Ecru shade .Packets : 1 nos

29 Reception 3 seater sofa Providing, supplying and placing of three seater sofa. SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an

additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette.

BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2

kg/cu. mtr, upholstered with fabric or leatherette. UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood

[moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat

& 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY : It is a welded Assembly 1 64870.03 64870.03

made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM.

Seat Height (SH): 45.0 CM.

30 1 seater sofa Providing, supplying and placing of one seater sofa. SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an

additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette.

BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2

kg/cu. mtr, upholstered with fabric or leatherette.

UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303]

& pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over

understructure for cushioning purpose.

LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Width (W): 86.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

31 Center table Providing, supplying and placing of coffee table. CENTER TABLE GLASS: It is 10 ±0.3 mm thick black tinted Toughened glass UV glued with

bushes made in SS 202 grade for focing with understructure.

CENTER TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade

Width of table= 112.0 cm, Depth=60.0 cm, height=34.9 cm.

32 Corner table Providing, supplying and placing of side table. SIDE TABLE GLASS: It is 10 ±0.3 mm thick black tinted Toughened glass UV glued with bushes

made in SS 202 grade for focing with understructure. SIDE TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade Dia.

12±0.04 as per IS:1762. Width of table= 60.0 cm, Depth=60.0 cm, height=34.9 cm. 2 13686.70 27373.40

33 chair Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood

and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give

comfort to popliteal area.

The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar

support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm. The chair seat & back size are

*SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf

as per IS:7888 for 25% compression.

ARMRESTS :The adjustable armrest is designed with the following features :· Up-Down adjustment– 6 steps (7.2 ± 0.5cm range)

· Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled Nylon insert.

CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism isdesigned with the following features:

· 360° revolving type.

· 3 position locking with anti shock mechanism.

· Tilt tension adjustment 1 15572.93 15572.93

PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm.

PEDESTAL ASSEMBLY : The pedestal is injection moulded in glass-filled Nylon andfitted with 5 nos. twin wheel castors. The pedestal is 66.1

±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors).

TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 76.1 CM.

DEPTH (D): 76.1 CM.

HEIGHT (H): 101.5 - 111.0 CM.

SEAT HEIGHT (SH): 44.5 - 54.0 CM.

S.No. Item Specifications Unit Qty Unit Price Total Price

3 Ceiling Supply, Installation, testing and commissioning of Ceiling microphone with Nos.

micropho automatic dynamic Beamforming technology, The beam will automatically detect

ne the position of the person speaking and will follow the person around the room at

all times. It should have 2 x Dante digital audio (Redundancy), Analog audio out

(Phoenix 3-pin), and Ethernet for Control and PoE connectivity ports. The

coverage of the ceiling microphone should be min 800 square feet or more. It

should have a true voice lift feature to increase audio intelligibility above the

ambient noise floor. It should support IT industry standards like IEEE 802.1x. It

can be controlled through software that can control and monitor the microphone in 2 ₹ 689,570.00 ₹ 1,379,140.00

any network. It should have min 100 dB SPL, 5ms latency, and min 90dBA or

higher dynamic range. High-precision audio settings for maximum control, setting

to exclude (min 5) and prioritize the areas of the room. It should certified from

Microsoft Teams and Zoom Video conferencing applications. It should have UL

62368 certification (including UL 2043 testing and compliance) and safety

certifications.

4 Digital Suppy Installation Testing and Commissioning of digital signal processor with Nos.

Signal minimum 12no. Or more Mic / line input with phantom power and AEC and 8 or

Processo more line level output, 1no. Or more GPIO at least 2 channel of USB input and

r output for software Video Conferencing, should have 8x8 channel of digital dante

input output, Should have sampline rate of 48kHz or better, Should be expandable

for port expansion, should support Control with App via iOS and Android devices, 1 ₹ 875,700.00 ₹ 875,700.00

or any third-party control system, Shall have Built-in filters, feedback suppression,

AGC single-device(chassis) use is permitted, but the combination of devices is not

accepted etc complete as required as per specifications

5 Amplifier Supply, Installation, testing and commissioning of 8 channel energy star rated Nos.

digital power amplifier,8 channel at 4 Ohm or 8 ohm energy-efficient amplifier - 8

x 30W or more at 70/100V Technology : Class-D,Input linking through miniature

switches, Switching mode power supply, Protection : DC Short circuit & Over

heating & Over load & Signal limiting, Frequency Response 120 Hz - 20 kHz or 1 ₹ 335,500.00 ₹ 335,500.00

better, Silent passive cooling etc complete required as per specifications.

Digitally signed by AMIT

6 Ceiling Supply, Installation, testing and commissioning of 6.5" two-way coaxial thin edge Nos.

Speakers ceiling loudspeaker having 100V transformer power taps from 60watts to 15watts

or better it should have metal back can for premium performance in demanding

applications, Conical dispersion : 142° or more, Low impedance RMS continuous

power of 60watts, impedance : 8 or less,frequency range (-10dB) : 70 Hz - 20

kHz, frequency response (±3dB) : 100Hz - 20KHz, Max SPL on 100v should be

105dB or more etc complete required as per specifications.

7 Camera Supply Installation Testing and Commissioning of Full HD 1080p @ 60 frames Nos.

per second PTZ Camera with minimum 20X Optical Zoom and FoV of minimum 57

deg, min 100 Presets.Camera should support simultaneous outputs through

Ethernet, HDMI, 3G-SDI, Audio In and can be controlled via RS232 & 422 In &

Out & IP.Panning angle -170° ~ +170°, Tilting angle -30° ~ +90° . The tilting and 0 ₹ 495,000.00 ₹ -

panning speed of camera should be minimum 300° per second. Camera should

support SRT, FreeD Protocol, PoE and Virtual USB Driver. OEM should be CE,

FCC, RoHS & BIS Certified with test lab report supporting the certifications.

8 Tracking Supply, Installation, Testing & Commissioning of Processor which can enable Nos.

Device Voice Tracking through PTZ Cameras integrated with Ceiling Tiles on IP. The

Processor should be capable of connecting minimum 4x Ceiling Tiles with 4x IP

based PTZ Cameras for Quadview output and Auto Switching . The processor

should have USB 3.0 Output for Soft VC. Quoted model should be BIS, CE, FCC 1 ₹ 295,700.00 ₹ 295,700.00

& RoHS Certified with Test Lab Reports.

9 USB to Supply Installation Testing and Commissioning of surface-mount USB-to-Dante Nos.

Dante endpoint, two-way volume and mute sync for Microsoft Teams,compliant with CE

Device and FCC, device shouold have Power-over-Ethernet (PoE) to IEEE 802.3af Class

0 standard and support Dante networking using standard CatX cable, device

should support the Speakerphone profile with and without echo cancellation,

enable two-way volume and mute syncronization with both PC and Mac platforms,

Dante with AES67 compliance,Sampling Rate(s) 48 kHz,should be from same 1 ₹ 195,500.00 ₹ 195,500.00

OEM as DSP etc complete required as per specifications.

10 Touch Suppy Installation Testing and Commissioning of control system with touch Nos.

Controlle panel/Ipad, 100/1000 Mbps, auto-switching, auto-negotiating, auto-discovery,

r full/half duplex, industry-standard TCP/IP stack, UDP/IP, CIP, DHCP, SSL, TLS, 1 ₹ 545,000.00 ₹ 545,000.00

SSH, SFTP (SSH File Transfer Protocol), FIPS 140-2 compliant encryption

Digitally signed by AMIT

11 Switch Supply, Installation, testing and commissioning of 16 port switch Nos.

12 Wireless Supply, Installation, testing and commissioning of wireless presentation device Nos.

Presente which should have following features Wireless content input up to 1080P, HDMI

r 2.0 output, should Support native wireless mirroring protocols like Airplay,

Miracast, Chromecast should Support plug-n-play HDMI/Type-C/U disk dongles

for wireless connection, Support Windows APP for wireless connection (MAC

APP will be available soon), Support 4 split screen view, Support wireless touch 1 ₹ 335,000.00 ₹ 335,000.00

back on interactive whiteboard/touch screen, Best-in-class data security with dual

network and high standard encryption, PoE supported, saving PSU when

connecting with PoE ethernet switch

13 TX Supply, Installation, testing and commissioning of HDMI RX extender with Nos.

complies with the advanced HDCP 2.2 and HDMI 2.0 standards, uncompressed

HD audio and video as well as control via a single run of Cat.5e/6/7 cable over

distances of up to 70 meters and upto 40mat 4K, HDBaseT feature support: HD

Video and Audio, and Control (IR/RS-232 pass-through) and CEC bypass, 6 ₹ 55,750.00 ₹ 334,500.00

Supports pass-through of many audio formats including LPCM (up to 8 channels),

Bitstream and HD Bitstream

14 RX Supply, Installation, testing and commissioning of HDMI TX extender complies Nos.

with the advanced HDCP 2.2 and HDMI 2.0 standards, uncompressed HD audio

and video as well as control via a single run of Cat.5e/6/7 cable over distances of

up to 70 meters and upto 40mat 4K, HDBaseT feature support: HD Video and

Audio, and Control (IR/RS-232 pass-through) and CEC bypass, Supports pass- 6 ₹ 55,750.00 ₹ 334,500.00

through of many audio formats including LPCM (up to 8 channels), Bitstream and

15 Cable Supply, Installation, testing and commissioning of Cable cubby (1 HDMI, 1LAN,1 Nos.

cubby Charging socket)

Digitally signed by AMIT

16 HDMI Supply Installation Testing and Commissioning of HDMI Audio Extractor should Nos.

Deembe extract up to 2 channels of LPCM audio or 5.1 channels of Bitstream audio from

dder an HDMI source, allowing the user to convert high quality HDMI audio into more

convenient analog (LPCM 2.0 sources only) or optical signals for use with

powered speakers or non-HDMI AV receivers. Both the input and output HDMI

ports should support 4K UHD resolutions up to 4K@60Hz (4:4:4, 8-bit) and should

capable of providing high quality audio and video performance. The unit should 1 ₹ 93,100.00 ₹ 93,100.00

supports passthrough of HD and standard Bitstream formats as well as LPCM 7.1

with audio sampling rates up to 192kHz. Built-in EDID management support

allows the user select from multiple EDIDs and, with the use of optional PC

software, to upload, download, or edit EDID files etc and complete as required

17 USB Supply, installation, testing and commissioning of USB peripheral switch which Nos.

switcher should be a 4x4 industrial USB 3.2 Gen 1 hub switch that enables four computers

to share up to four USB 3.2 Gen 1 peripheral devices such as keyboard, mouse,

and other USB equipment. The switch should support SuperSpeed data transfer

rates up to 5 Gbps, be compatible with Windows, Mac, and Linux platforms, and

allow port selection via front panel pushbutton, external remote controller, or RS-

422/RS-485 link through a 5-pin terminal block. The device should feature four

USB Type-B ports for computer connections and four USB Type-A ports for

peripheral devices, with support for USB BC 1.2 battery charging and overcurrent

protection. The unit must offer hot plugging, power-on detection with automatic

focus switching, and display port focus via LED indicators. It should be housed in

a robust metal chassis with wall and rack mount options

18 USB Tx Supply, Installation, Testing & Commissioning of USB 3.2 Extenders. Transmitter Nos.

Rx should have 1xUSB C input port, 1X RJ45, 1xUSB-A Output Port. Receiver

should have Input Port 1×Cat5e/6A/7 (RJ45). 1×USB-C, 3×USB-A Output Port.

Bandwidth upto 5Gbps (SuperSpeed), Tranmission distance upto 100M. Devices

should be controlable by the USB host on a transmitter. Should have backward 1 ₹ 96,000.00 ₹ 96,000.00

compatibility with USB 2.0

19 8x8 Supply, Installation, testing and commissioning of Eight HDMI inputs matrixed to Nos.

HDMI eight HDMI outputs with HDMI 2.0a specification and 18Gbps (600MHz) 4K UHD

Switcher support, HD resolutions up to 3840×2160@60Hz (4:4:4, 8-bit) &

4096×2160@60Hz (4:4:4, 8-bit), 16-bit Deep Color up to 1080p@60Hz. Eight

Audio output ports can pair with eight HDMI outputs individually. Audio support

Digital and analog Formats. Device should be provides an intuitive set of front

panel controls with an LCD as well as RS-232, Telnet, WebGUI, and IR remote

control options.

20 Cables Cables & connectors Lot 1 ₹ 150,000.00 ₹ 150,000.00

Digitally signed by AMIT

SI.NO DSR DESCRIPTION

UNIT QTY RATE NDSR AMOUNT DSR AMOUNT

1 MR Supply, Installation, Testing & Commissioning of Server based Communication System with all the

required Software licenses and Hardware - IP-PBX/IP Telephony Communications Server: The IP

Telephony Solution shall support the following Services - Voice, Video, IM, Presence and Audio

Conference The IP Telephony Solution should support H.323 and SIP The Solution should support the

following Trunks - FXO, E1 PRI and SIP The IP Telephony solution should incorporate all licenses for the

Phones and Trunks Solution should support all Extensions from Day 1 with future scalabilityupto 500 Nos 1 ₹ 2,250,000.00 ₹ 2,250,000.00 0

users. Licenses for all Phones supplied should be provisioned on Day1 Solution should support Hard 20

IP Phones, Softphones, Video Phones, Extensions with necessary Licenses, and 50 Analog Phones,

Rack mount architecture, complete as required and as per technical specifications.or its equivalent

2 MR Supply, Installation, Testing & Commissioning of 2.8” (diagonal) color display—320 x 240 pixels,

Multiple line phone with four red / green line / feature indicators around display, 4 Context sensitive

soft keys, Hard buttons for phone, messages, contacts, history, home, navigation cluster, headset,

speaker, volume, mute, LEDs for speaker, mute, headset, essage, history, Wideband audio in handset

and wired headset, Full duplex speakerphone & handset, Ergonomic hearing aid compatible handset

supports TTD acoustic coupler, Message waiting indicator, Mute key with optional mute alerting, IC

call alerting with 360-degree visibility, Dual-position stand, optional wall-mount stand, Gigabit

Ethernet (10 / 100 / 1000) line interface, Second Ethernet interface 10 / 100 / 1000 Mbps, PoE Class

(IEEE 802.3af) registers as class 1 device and supports 802.3az, Optional AC to 5 volt power supply • Nos 2 ₹ 27,750.00 ₹ 55,500.00 0

SIP protocol support, Standards-based codec support: G.722, Opus, Configurable via Web interface,

Support for HTTPS, TLS and SRTP for encryption, Recent Call Log (100 entries), Zero touch deployment

via Device Enrollment Services Support, Supports the following languages: Dutch, English (UK & US),

French, (Canada), French (France), German, Italian, Japanese, Portuguese (Brazil), Simplified Chinese,

Spanish (Latin America), Spanish (Spain),Traditional Chinese, Includ Licence.or its equivalent

3 MR Supply, Installation, Testing & Commissioning of Analog Phones

4 MR Supply, Installation,Testing and commisioning of IP phone license complete as required

Digitally signed by AMIT

ACTIVE & PASSIVE

Item Total Price

S.No. CODE Units Qty Rate

NDSR Amount DSR Amount

Supply, Installation, Testing and Commissioning of 24port L3 Switch with switching capacity of 3.2 Tbps,

forwarding performance of 1 Bpps with 24x 1/10/25G Gigabit Ethernet + 4x 40/100G Uplink

ports,Redundant hot swappable Power Supply and fans/Fantray.Should have advance layer 3 (RIPng,

OSPF,IS-IS, BGP , VRF , VXLAN , 802.1x, Macsec , PIM SM, PIM SSM, PIM-BIDIR and MPLS) from day-1.MAC

1 MR address support for 32 K , 200,000 IPv4 unicast routes and 100,000 IPv6 unicast routes entries ,32,000 Nos 1 ₹ 887,500.00 ₹ 887,500.00 ₹ -

IPv6 multicast routes , 25K Security ACL , Should support min 16 GB internal DRAM, 16 GB internal Flash

memory , 32 MB Packet buffer. Common Criteria Certification like NDPP or EAL and Ipv6

Certification from day-1

Supply, Installation, Testing and Commissioning of 24 Port POE+ Access Switch to provide 24 nos. 1G Base-

T ports with minimum PoE budget of 350W and 4x 10G SFP+ uplink ports. Should support internal

redundant Power Supply and support dedicated slot for modular stacking, in addition to asked uplink

ports with stacking bandwidth of minimum 80 Gbps with 8 switch in single stack. Should support min 2GB

2 internal DRAM, 4GB internal Flash memory , 6 MB Packet buffer, 16 K MAC address, 11 K IPv4 routes ,1k Nos 5 ₹ 280,500.00 ₹ 1,402,500.00

Multicast Routes , 1500 ACL entries, Should have static, RIPv1, RIPv2, RIPng,OSPF, MACSEC,802.1x , PBR

and VRRP from day 1 & upgradable to support IS-IS, VXLAN & VRF. Common Criteria Certification NDPP

and Ipv6 Certification from day-1

Supplying and drawing of LSZH STP 4 pair CAT 6 LAN low smoke Cable in the

existing surface/recessed Steel/ PVC conduit as required.

Supply, Installation, Testing & Commissioning of CAT 6 Information Outlet, meets all TIA

and ISO requirements Complete in all respect as required by the site etc. complete as required.

Supply, Installation, Testing & Commissioning of CAT 6 Patch Cord LSZH 1 Mtr, 4 pair

26 AWG stranded copper wire, Pre-terminated with RJ45 plugs, Slim clear anti-snag slip

on boots meets all TIA and ISO requirements. Complete in all respect as required by site

5 39.12.1 completion etc. complete as Nos 100 ₹ 151.00 ₹ 15,100.00

Supply, Installation, Testing & Commissioning of CAT 6 Patch Cord LSZH 3 Mtr, 4 pair

26 AWG stranded copper wire, Pre-terminated with RJ45 plugs, Slim clear anti-snag slip

on boots meets all TIA and ISO requirements. Complete in all respect as required by site

completion etc. complete as

Supply, Installation, Testing & Commissioning of dual face plate having provision for

one I/O along with spring type shutter for dust proof, made of ABS PVC plastic etc.

7 MR complete as required. Nos 50 ₹ 460.00 ₹ 23,000.00 ₹ -

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of 24 Port loaded Cat 6 Jack Panel,

Staggered 24 Port panel with All port LED in 1U Rack Unit, Copper Alloyed Contact Material,

8 MR black color, Front Port Labeling, 22-24 AWG Wire Accumulation etc. Nos 4 ₹ 36,625.00 ₹ 146,500.00 ₹ -

complete as required.

Supply, Installation, testing and commissioning of 42U Normal Rack with accessories

Supply, Installation, Testing & Commissioning of Horizontal cable manager etc.

complete as required.

Digitally signed by AMIT

S No Description Unit Qty Rate DSR Amount

Supplying Installation Testing and Commissioning of 4MP IP IR Dome Camera having following

specifications and features etc :- 1) Signal System: PAL/NTSC, Signal to Noise Ratio: > 50

dB,Camera should display Camera title, Date & Time in live & recorded video 2)Image Sensor:

1/2.8" or better progressive Scan CMOS to get color image even at night condition(Minimum

Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with IR or better) True Day & Night High

Performance Mechanical IR cut filter with auto switch, Integrated IR Source (Auto, Manual)-

Inbuilt IR LED's with effective distance upto 50 meter or better and 30 meter for colour view in

night, Imaging: 1/3s to 1/30000s electronic shutter support, Auto Gain Control , White Balance-

Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking.3)

Compression (Minimum): Video:- H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC,

G.723 4) Wide Dynamic Range:- WDR (120dB or more) 5) Digital Noise Reduction:- DNR (3D)

On/Off 6) Video Streaming & Frame Rates :- Triple streaming , configurable Main stream: 4MP

(2560×1440)25/30fps , Sub streams minimum: 720P@25/30 fps 7) Image Setting: Rotate Mode,

saturation, brightness, contrast, sharpness adjustable through client software or web browser,

Edge Analytics: Tripwire, Intrusion, Motion Detection 8) Cyber Security: AES 256-bit Encryption,

Configuration encryption, trusted execution, Digest, security logs, account lockout, video

4MP @ 25/30fps@1440P (2560 x 1440) Dome Camera with 2.8/ 3.6/ 6/8/12 mm fixed lens (as

40.3.1 per site requirement).

Digitally signed by AMIT

NVR:- Supplying Installation Testing and Commissioning of following Channel Network Video

Recorder (NVR) with camera licenses to record for all channels having specifications and

features etc as mentioned below : 1) Network Video Recorder Embedded/ Installed OS (Linux)

along with Camera Licenses for number ofchannels of NVR to record per NVR and to provide a

live view, storage and simultaneously Multi-channel playback of all IP, IR camera or more and

must be ONVIF with minimum support of 256Mbps incoming Bandwidth. 2) NVR should

support H.265 or better, H.264,

MJPEG, MPEG4 support 3) Must support 1 channel Input, 1 channel Output, RCA for Two-way

Talk 4) Intelligent auto power on when power resumes after

power outage. 5) Storage: It should support minimum 2 SATA Slots with 20TB capacity/ Slot. 6)

Connectivity Interface : 1 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x RS232 7)

Backup Interface : Its should have 2 Nosx USB port (1x USB3.0, 1xUSB2.0) 8) Video Output

Ports: 1x HDMI and 1 VGA 9) Alarm Ports: It should have 4/1 Ch In/ Out ports to connect

40.10 various type of external sensors and output devices like hooter/ Siren etc. 10) Email & SMS

Altert options: Option for SMS/ Email Alerts to minimum 5 designated mobile number for

power failure, HDD failure, vandalism, tempring, network disconnection and panic 11) Web &

Mobile Application: Web, Mobile app ( For

iPhone, iPad, Android Phone) for alerts and viewing. 12) Protocols: HTTP, HTTPS, TCP/IP, IPv4,

UDP, NTP, DHCP, DNS, SMTP, UPnP, DDNS, Alarm Server, IP Search, Multicast, Auto

Registration, ONVIF (Profile T, Profile S, Profile G), CGI, SDK and OEM

Cloud for remote monitoring without any public IP need. 13) Standards: CE, FCC, RoHS and BIS

Certified 14) Power Supply : Should support 12VDC, 4Amp or AC100-240V, 50/60Hz Power

supply. 15) Operating Condition : Ambient Temperature (-5°C

to 50°C), humidity 90% (max) (non-condensing) 16) The VMS, NVR application shall support all

the features & functionalities of the offered cameras. 17) VMS should consist of Base license

and Channel Licenses. VMS should be provided with camera

Licenses , with no dependency of VMS licenses by binding with the MAC address of the cameras

to achieve the functionality. 18) The NVR OEM shall be responsible for providing a mobile

08 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9, 2nd Nos. 1 10078 10,078.00

HARDDISK:- Supplying, Installation, Testing and Commissioning following capacity Serveillance

grade Hard Disk with upto 256MB/s Transfer Rate, 256 MB Cache, 7200

40.12 RPM Disk Speed, 3.5 inch form factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC,

KC, Maghreb, RCM, UKCA, VCCI, CB-Scheme, TUV, UL Certifications.

Digitally signed by AMIT