Providing and Laying Rigid Pavement in the Back up Area in between 7th Berth Approach Road and 8th Berth Approach Road and Resurfacing the 7th Berth Approach Road inside Green Gate at VOCPA

Excavation for roadway in soil using hydraulic excavator of 0.90 Cum. bucket capacity including cutting and loading in tipper, trimming bottom and side slopes in accordance with requirement of lines, grades and cross section and transporting to the embankment location within all lifts and lead upto 1000 meters etc., complete as per clause 301 of MORT&H Specification (Fifth Revision) and as directed by the departmental officers.

Preparation of sub grade by excavating earth work to 15 cm average depth, dressing to camber and consolidating with power road roller including making the undulation area levelling etc., and disposal of surplus earth to the low lying area to a lead of 1km. etc., complete complying with AISS and as directed by departmental officers.

Providing and laying of Granular Sub-base (GSB) - [Plant Mix Method] by mechanically and compacting in layers in each layer 125mm using stone aggregate by providing close Grading - I materials 53 mm to 26.5 mm @ 27.5%, 26.5 mm to 9.5 mm @ 22.5%, 9.50 mmto 4.75 mm @ 10%, 4.75 mm below @ 40% mixing in a mechanical mix plant at OMC and loading tippers conveying of mixed material to work site dumping and spreading in uniform layers with motor grader on prepared surface and compacting with vibrator roller to achieve the desired density complete as per clause 401 of MORT&H Specification (Fifth Revision) and as directed by the departmental officers.

Providing Form work including centring, shuttering for foundation footings of columns, mass concrete so as to give a rough finish shuttering and propping etc., complete complying with AISS and as directed by the departmental officers.

Providing and laying Plain Cement Concrete 1:4:8 (One part of cement, 4 parts of Coarse sand & 8 Parts of 40 mm nominal size metal ) for foundation using 40 mm nominal size graded metal including mixing, laying, levelling, consolidation, finishing and curing etc., complete complying with AISS and as directed by the departmental officers.

Providing and fabricating 32mm dia MS bars and placing in position as dowel bars for expansion joints as per details shown in the drawing and as directed including all handling, cutting, bending, all labour, materials, equipment, tools etc., complete. Dowel bar of length 500mm for expansion joints (one half of the rod painted with bitumen and greased to avoid bonding with concrete) including providing necessary PVC sleeve & cap, cotton waste @ 300mm c/c etc., complete and as directed by the departmental officers.

Fabricating and placing in position of M.S / Tor steel grills for R.C.C works in all floors including cost of Steel, cutting, bending, binding with 16 Gauge GI Binding wire and placing in position etc., complete complying with AISS and as directed by the departmental officers.

Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in abatching and mixing plant as per approved mix design (M40), transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of admixtures as approved, finishing to lines and grades etc., complete as per clause 602 of MoRT&H specification and as directed by the departmental officers.

Supplying and laying bitumen sealing compound of grade 'A' conforming to IS 1834 - 1984 (or its latest edition) for Expansion joints to a width of 20mm and 25mm deep for filling and including painting the edges of the joint with an approved primer all as specified and as directed at site of work including all materials, labour, tools, equipment, fuel, etc., complete and as directed by the departmental officers.

Supplying and laying bitumen sealing compound of grade 'A' conforming to IS 1834 - 1984 (or its latest edition) for Longitudinal joints and Contraction joints to a width of 10mm and 65mm deep for filling and including painting the edges of the joint with an approved primer all as specified and as directed at site of work including all materials, labour, tools, equipment, fuel, etc., complete and as directed by the departmental officers.