REPAIR MAINT OF CHAIN LINK FENCING BARBED WIRE CONCERTINA COIL POSTS ETC AND RAISING MAINS OF OH TANK WITH ALLIED WORKS UNDER GE NARANGI

Amount

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation, laying of pipe or for shafts, wells cesspits,man holes etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed.

Returning, filling, in including spreading, levelling, watering and well ramming in layers n.exc. 25cm thick complete all as specified and as directed.

Removing excavated soil to distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point etc complete all as specified and as directed.

Supplying, laying & testing 300 mm dia ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for push-on - joint with inside cement mortar lining, internal metallic zinc coating and external black bitumen coating duly ISI marked laid in trenches including making good disturbed surfaces of road /pavement/PCC surface as required including taking out old existing pipeline of any description and size complete all as specified and as directed.

Supplying, laying & testing 250 mm dia ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for push-on - joint with inside cement mortar lining, internal metallic zinc coating and external black bitumen coating duly ISI marked laid in trenches including making good disturbed surfaces of road /pavement/PCC surface as required including taking out old existing pipeline of any description and size complete all as specified and as directed.

Supplying, laying & testing 200 mm dia ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for push-on - joint with inside cement mortar lining, internal metallic zinc coating and external black bitumen coating duly ISI marked laid in trenches including making good disturbed surfaces of road /pavement/PCC surface as required including taking out old existing pipeline of any description and size complete all as specified and as directed.

Supplying, laying & testing 150 mm dia ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for push-on - joint with inside cement mortar lining, internal metallic zinc coating and external black bitumen coating duly ISI marked laid in trenches including making good disturbed surfaces of road /pavement/PCC surface as required including taking out old existing pipeline of any description and size complete all as specified and as directed.

Supplying, laying & testing 100 mm dia ductile iron pressure pipe socket and spigot end, class K-7, confirming to IS-8329/2000 blast furnace slag cement with portland cement properties suitable for push-on - joint with inside cement mortar lining, internal metallic zinc coating and external black bitumen coating duly ISI marked laid in trenches including making good disturbed surfaces of road /pavement/PCC surface as required including taking out old existing pipeline of any description and size complete all as specified and as directed.

M&L for Ductile iron (DI) fittings 100 mm to 450 mm bore for spigot and socketed pipes such as bends (any type radius and angle), tappers any type (straight, bend, increasing, decreasing or double socket type etc), tee pieces, single branch, Y junction, double branch, cross (all sockets or socket and spigot etc), collars, caps & plugs etc. conforming to IS 9523 complete all as specified and as directed.

S&F GI tubing 50 mm bore, medium grade with all fittings and fixed complete laid in trenches including taking out old existing pipeline of any description and size complete all as specified and as directed.

S&F GI tubing 25 mm bore, medium grade with all fittings and fixed complete laid in trenches including taking out old existing pipeline of any description and size complete all as specified and as directed.

S&F GI tubing 20 mm bore, medium grade with all fittings and fixed complete to wall, ceiling including taking out old existing pipeline of any description and size complete all as specified and as directed.

S & F in repairs 50 mm bore gun metal globe or gate valve cast copper alloy, screwed down, high pressure with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

S & F in repairs 25 mm bore gun metal globe or gate valve cast copper alloy, screwed down, high pressure with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

S & F in repairs 20 mm bore gun metal globe or gate valve cast copper alloy, screwed down, high pressure with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

S&F in repairs, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed for 20mm bore pipe ( minimum weight -210 gms ) complete all as specified and as directed.

S&F in repairs, bib taps 15mm dia cast copper alloy chromium plated, fancy type with crutch or butter fly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

Materials and Labour for Run Lead joints suitable for 300 mm bore cast iron spigot and socket end pipes and fittings including dismantling of old worn out joint by burning out old lead etc and testing complete all as specified and as directed.

Materials and Labour for Run Lead joints suitable for 250 mm bore cast iron spigot and socket end pipes and fittings including dismantling of old worn out joint by burning out old lead etc and testing complete all as specified and as directed.

Materials and Labour for Run Lead joints suitable for 200 mm bore cast iron spigot and socket end pipes and fittings including dismantling of old worn out joint by burning out old lead etc and testing complete all as specified and as directed.

Materials and Labour for Run Lead joints suitable for 150 mm bore cast iron spigot and socket end pipes and fittings including dismantling of old worn out joint by burning out old lead etc and testing complete all as specified and as directed.

Materials and Labour for Run Lead joints suitable for 100 mm bore cast iron spigot and socket end pipes and fittings including dismantling of old worn out joint by burning out old lead etc and testing complete all as specified and as directed.

S&F in repairs, sluice valve (heavy duty) with heavy duty stainless steel spindle conforming to IS 14846 (2000) both end flanged class PN 1.6 of size 300 mm dia including necessary nuts,bolts washers and gasket complete all as specified and as directed.

S&F in repairs, sluice valve (heavy duty) with heavy duty stainless steel spindle conforming to IS 14846 (2000) both end flanged class PN 1.6 of size 200 mm dia including necessary nuts,bolts washers and gasket complete all as specified and as directed.

S&F in repairs, sluice valve (heavy duty) with heavy duty stainless steel spindle conforming to IS 14846 (2000) both end flanged class PN 1.6 of size 150 mm dia including necessary nuts,bolts washers and gasket complete all as specified and as directed.

S&F in repairs, non return valve 200mm dia screwed type ISI marked including jointing materials complete all as specified and as directed.

S&F in repairs, non return valve 150mm dia screwed type ISI marked including jointing materials complete all as specified and as directed.

S&F in repairs, non return valve 100mm dia screwed type ISI marked including jointing materials complete all as specified and as directed.

S&F in repairs, cast iron foot valve 200mm dia screwed type ISI marked confirming to IS 4018 including jointing materials complete all as specified and as directed.

S&F in repairs, cast iron foot valve 150mm dia screwed type ISI marked confirming to IS 4018 including jointing materials complete all as specified and as directed.

S&F in repairs, cast iron foot valve 100mm dia screwed type ISI marked confirming to IS 4018 including jointing materials complete all as specified and as directed.

S&F Straight plain brass ferrules 25mm (or connecting screws) screwed both ends and fixed complete all as specified and as directed.

Supply only glad packing of different sizes as directed complete all as specified and directed.

M & L for construction of brick masonry valve pit of size 90 cmx 90 cm x 90 cm (internal dimension) one brick thick wall built in CM (1:4) on 100mm thick PCC (1:4:8) type D2, (nominal mix) as in foundation, and 15mm thick rendering in cement mortar (1:4) both externally and internally, external plaster shall be up to 15cm below GL, providing valve pit cover made of 3.15mm thick MS sheet/plate, including provision of hinges, handle and locking arrangement including40X40X 6mm angle iron frame fixed on top of valve pit by means of MS hold fast 40x6mm and 150mm long, embedded in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) block of size 230X200X100mm, including two coats of anti-corrosive paint over a coat of red oxide zinc Chrome primer and necessary earth work in soft/loose soil including demolition of old valve pit complete all as specified & directed.

Cutting the existing road of 3.65 m wide and pathway as per site requirement for laying various size of DI pipe under the road and making good distrubed surface as per existing road/ pavement/ PCC surface complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillar including coping etc. complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan any radius, built in cement mortar 1:4 as in half brick thick work complete all as specified and as directed.

M & L for PCC 1:2:4 type B-1 (using20 mm graded stone aggregate) as in coping / benching etc. including weathering , slightly rounded or chamfered angles and necessary form work complete all as specified and as directed.

M & L for PCC 1:3:6, type C2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M & L for precast RCC 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in post, fencing posts, starining or terminal posts, struts etc. for fencing average sectional area exceeding 100 Sqcm and not exceeding 250 Sqcm with or without chamfered angles and flat , splayed, rounded or mitred tops complete all as specified and as directed.

M & L for rendering 15 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed

M&L for preparation of newly plastered surface of walls and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of primer complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

M & L pre-polished cement concrete chequered tiles area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm and 25 mm thick with white cement and pigments of approved make jointed with cement slurry and pointed with white cement mixed with pigment to match with the tiles over and including screed bed of 20 mm thick in cement mortar (1:6) including demolition of old slabs and tiles complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape as required including cranking, bending spirally for hooping for columns,hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia as in reinforcement bar complete all as specified and as directed.

M&L for mild steel TMT bars 6 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

S&F in repair mild steel angle iron post & strut etc. in fencing including embedding in concrete and screwing etc. including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work confoRming to Fe-290 GdeE-165 completed all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F rolled mild steel framed works as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hangings also fastening and fixing etcconforming to Fe.290.Gde-E-165.

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5cm but not exceeding 10 cm long and diameter of shank 5 to 10mm completed all as specified and as directed.

Dismantling fencing wire mesh of any size and type complete all as specified and as directed.

Supply only chain link fencing wire mesh of size 75X75mm, made with 3.15 mm dia including 5mm dia line wire conforming to IS 2721 mild steel galvanised wire complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolt etc including provision of binding wire complete all as specified and as directed

S & F galvanized two strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to RCC / steel post etc. including securing or tying at crossing with and providing of galvanized mild steel wire, staples or steel pins, etc. (each line of wire to be measured separately) complete all as specified and as directed.

Restraining and resuring including making good staple of galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing complete all as specified & as directed.

S & F providing and fixing 610mm dia Razor Concertina coil fencing with and including required clips, pins, etc. as per manufacturer's instruction and as per specification fixed on the Y angle. Each concertina coil shall be fixed to MS angle with existing rows of barbed wire on each of Y angle. There shalll be 80 ( eighty) circles in each 9.00 mtr length. Number of clips in each 9.00 mte shall be 200 Nos., central core wire 12 SWG hot galvanised high tensileed wire : UTS- 145-160 Kg/Sqmm. Razor strip 0.50mm thick hot dipped galvanised and of length 19mm, clips 1.5mm thick made of SSAISI 410 complete. ( Note: Measurment and payment shall be considered on length of security wall/ fencing and not actual length of concertina coil complete all as specified and as directed.

M&L for construction of brick masonry valve pit of size 60 cmx 60 cm x 60 cm (internal dimension) one brick thick wall built in CM (1:4) on 100mm thick PCC (1:4:8) type D2, (nominal mix) as in foundation, and 15mm thick rendering in cement mortar (1:4) both externally and internally, external plaster shall be up to 15cm below GL, providing valve pit cover made of 3.15mm thick MS sheet/plate, including provision of hinges, handle and locking arrangement including40X40X 6mm angle iron frame fixed on top of valve pit by means of MS hold fast 40x6mm and 150mm long, embedded in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) block of size 230X200X100mm, including two coats of anti-corrosive paint over a coat of red oxide zinc Chrome primer and necessary earth work in soft/loose soil including demolition of old valve pitcomplete all as specified & directed.

S. R. TRADING